Search Documents

By N. W. Munro

SYNOPSIS Certain disadvantages associated with the use of Anfex have been raised on previous occasions. This interim investigation shows that by loading at lower pressures the sensitivity to initiation of Anfex can be improved. Associated with this is a reduction in velocity of detonation and charge density which should lead to more desirable fragmentation. The effect of lower loading pressure on other factors is also considered. INTRODUCTION Discussion at the Symposium on the use of Anfex in Underground Mining, conducted by the South African Institute of Mining and Metallurgy during May 1968 showed that there was considerable uncertainty and diversity of opinion on the characteristics of Anfex and its method of application. Some of the disadvantages associated with the use of Anfex were: Inadequate sensitivity to initiation; Excessive fragmentation of the rock and damage to the hanging and footwalls; Wastage as a result of blow-back; Poor water resistance. As a result of this, further investigations on the properties of Anfex have been carried out and, although these have not reached finality, it is considered that a progress review may be of interest and assistance to the mining industry. EXPERIMENTAL TECHNIQUE The work was carried out on a laboratory-scale where, for test purposes, the explosive was loaded into 1 in. (nominal) internal diameter steel pipes unless otherwise stated. Charging was conducted with a 1 in. (nominal) Schutte-Koerting eductor having a 0.2 in. internal diameter venturi nozzle, the Anfex being fed into the eductor from a conical hopper fitted directly above it. A 5 ft long copper loading tube with outside and internal diameters of 3/4 in. and 5/8 in., respectively, was fitted to the discharge end of the eductor. The remote end of the loading tube was inserted into the test pipe so that it was about 6 to 8 in. from the closed end of the pipe. The loading apparatus was withdrawn as the pipe filled, maintaining approximately the same stand-off distance throughout the operation. REVIEW Sensitivity to initiation Sensitivity of Anfex to initiation was found to deteriorate when the dynamic pressure of the air to the eductor was increased. This was attributed to increasing charge density and it was found that at a charge density of about 1.05 g/cm3, which

The following notes have been compiled to assist authors in the preparation of papers for presentation to the Institute and for publication in the Journal. All papers must meet the standards set by the Council of the Institute, and for this purpose all papers are referred to at least two referees appointed by the Council. Although the worldwide readership of the Journal results in a preference for papers in English, the Council treats papers in Afrikaans on an equal basis, but, to meet the needs of the majority of readers, an English summary of some 5OO to 750 words should be provided.

Jan 1, 1984

By A. Cambitsis

We show that the prioritization of business improvement and performance management decisions may be significantly improved by taking into account the systemic effects of changes made in a single process area. To do so we build a model of a mining value chain, taking into account consequential downtime that arises from downstream and upstream starvation and choking effects of each activity. Introducing the concept of internal capacity, this approach yields insight into the relative importance of key metrics such as loading and hauling rates. We suggest that a holistic view of this type should be a core component of business improvement and performance management decisions.

Jan 1, 2012

Since 2001, the Hybrid Stress Blast Model (HSBM) project members have developed a software suite to model the complete blasting process from non-ideal detonation to muck pile formation. To preserve the physics and improve solution time, the breakage engine uses a combination of analytical models and 2D axisym-metric finite differences to model near-field crushing, coupled to 3D discrete lattice fracturing and distinct element numerical methods to model throw and muck pile development. The model has been validated by comparison with laboratory and field tests in kimberlite. Multiple blasthole simulations are used to demonstrate how changes to blasting parameters can influence downstream efficiencies. Case studies of wall control blasting show that the presplit design must balance the two opposing effects of increased damage with increased charge and decreasing attenuation of the seismic waves with decreasing charge. Modelling of decoupled explosives needs further development. Reducing the charge towards the back of the trim blast results in a much more significant decrease in back damage than altering the timing. The model demonstrates how separation along the weaker planes in a jointed rock can coarsen the fragmentation, leading to inefficient beneficiation, and extends the damage to a distance of at least twice the burden behind from the blasthole, severely compromising the wall stability.

Jan 1, 2012

By G. A. Wiebols, N. G. W. Cook, N. C. Joughin

Discussion R. E. Rarnes (Member): The original concepts and the pioneering work now brought to the practical test stage by the Mining Research Laboratory team deserve our highest praise. The authors of this comprehensive paper rightly stress the urgency of establishing the extent to which the apparent potential can profitably be realised in practice. It is to be hoped that adequate funds will be made available by individual mining companies, the Chamber of Mines and manufacturers to attract the necessary staff and maintain the high rate of achievement of the last two years. From the Seventy-Eighth Annual Report of the Chamber of Mines and its members we see that, in 1967, with a Working Revenue of R759.8 million from gold and R54.6 million pit mouth coal sales and with profits from gold and uranium and pyrite of R307.9 million, only R1.9 million was spent by the Chamber on all forms of Research. It is considered unlikely that the associated mining companies and manufacturers exceeded this investment expenditure. Assuming a total of R4 million spent by the industry on Research and Development, this is less than half of 1 per cent of sales of gold and coal. This percentage, so low in comparison to North America and Europe, is no worse than that of Exploration expenditure which, in 1967, with South Africa's total mineral production of R1,287 million, was estimated to have been R6 million (Pretorius 1968). In a primary industry with ever present depletion of ore deposits and with cost escalation, expenditure on Exploration and on Research and Development is not a risky luxury but a tactical obligation. The potential rate of return on research expenditure into rock breaking is high. Stores consumed by gold and coal mines, members of the Chamber of Mines, totalled R316.2 million in 1967. Except for purchased power costing R42.2 million the highest cost group was explosives, drills and drill steel totalling R33.8 million or 10.7 per cent of the total stores consumed. In the paper under discussion it is claimed that the low 'effective stoping width' should greatly reduce the likelihood of rock falls or rock bursts to the extent that permanent support can be dispensed with. Insofar as this narrow cut is only 12 in. in advance of the working area which, with a 10 in. channel, is unlikely to be much reduced in width from that achieved by current methods, this claim is not readily understandable. Were it to have been based upon the regional support gained from packed waste it would have been more acceptable. Pre-developed stope drives may give serious trouble at depth and for this reason it is questioned whether a stoping area can avoid periodic sub-development blasting-the spoil and fumes from which will interfere with the rock flow and continuous mining of the rock-cutter. If, in the mining method proposed by the authors, stope drives are cut as small as possible (6 ft by 6 ft) then 25 per cent of the total tons handled (excluding resued waste) and 5 per cent of the gold will be blasted conventionally in the stope. At this stage one cannot envisage tunnelling machines economically or practically capable of such work. The various methods described by the authors and subsequent contributors for breaking waste are most interesting. It was noted that the 'bull wedge' and 'explosives' in Fig. 1 of the paper were no further from the ideal point 'A' than was 'cutting'. The writer considers that the bold and imaginative steps taken by the Mining Research Laboratory Team, the mining companies and the manufacturers concerned will eventually lead to a successful rock cutting machine with universal application largely independent of rock type. This may take many years. In the meantime other methods of improving productivity of saleable metal by rock breaking teams should be investigated even if such methods have local applications only. In 1955 the writer conducted tests with a wire saw similar to those used in quarries in the Northern Transvaal and elsewhere. Jeppestown shale, the immediate footwall of much of the East Rand gold field, was cut at the rate of 6 in. per hour using sand, water and a special endless rope driven by a low h.p. motor. A hypothesis on its application was submitted to the Office of the Government Mining Engineer in 1955 and to other mining institutions in 1966 after the writer returned to South Africa. By inference, rope sawing was classed as less promising than other methods tested in the Orange Free State Goldfields (Parker 1969). With highly resilicified hanging and footwall quartzites this was not surprising and confirmed the writers findings when testing hanging wall quartzite from the East Rand in 1955. The relatively uniform conditions, the low strength, hardness, and silica content of the Merensky Reef platinum deposits (Gray and von Bardeleben 1969) and in particular, the existence of overlying Merensky pyroxenite (Cousins 1964) make this and the East Rand attractive areas for larger scale testing of wire saws. It is envisaged that in suitable rock types the 5/8 in. slot would be advanced down dip or down a minor dip. In undisturbed areas 'faces' of up to 200 ft in length could be cut several feet in advance of breaking which could then consist of light blasting to the second free face or some of the methods now being tested for breaking waste in rock-cutting operations. A wire saw is an inexpensive and simple machine which, in some areas, could make significant and early gains in rock breaking efficiency as well as in ground and stoping width control.

Jan 5, 1968

By D. F. Malan, L. Scheepers

Seismic risk in the deep gold mines of South Africa has been studied for many decades. A clear understanding of the effect of geotechnical conditions on the seismic hazard nevertheless remains elusive. Certain reef types seem to be associated with a higher risk of rockbursts. The stability and deformation behaviour of excavations on the different reef horizons are affected by the rock types and the varying strength properties. The seismic response to mining is therefore also expected to differ according to the geotechnical conditions. As a case study of this behaviour, the seismicity at Mponeng mine was investigated. On the VCR (Ventersdorp Contact Reef) horizon, two areas can be delineated. On the eastern side of the mine, the footwall is shale, and on the western side it is a strong brittle quartzite. More large-magnitude events occur in the area with the shale footwall than the area with the quartzite footwall. Moment tensor analyses indicated that the majority of the large-magnitude events are not related to geological structures, but are face-related, implying that shear failure of intact rock is occurring ahead of the mining front. Preliminary modelling indicated that the closure volume for the shale footwall may be higher than that for the quartzite footwall, providing a possible explanation for the observed difference in seismic response.

Mar 2, 2022

By D. F. Malan, J. A. L. Napier

A number of shallow coal or hard rock mines employ pillar mining systems as a strategy for roof failure control. In certain platinum mine layouts, pillars are designed to ‘crush’ in a stable manner as they become loaded in the panel back area. The correct sizing of pillars demands some knowledge of the pillar strength and the overall layout stress distribution. It is particularly important to understand the impact of the layout geometry on the effective regional ‘stiffness’ of the rock mass around each pillar. An important design strategy is to model relatively detailed layout configurations which include a precise representation of the local pillar layout geometry and to analyse multiple mining scenarios and extraction sequences to select optimal pillar sizes and barrier pillar spacing. Although computational solution techniques are now impressive in terms of run time efficiency, a major difficulty is often encountered in assigning suitable material properties to the pillars and in devising an effective material description of the layered rock strata overlying the mine excavations. This paper outlines an efficient numerical strategy that can be used to assess large-scale pillar layout performance while retaining the ability to modify individual pillar constitutive behaviour. The proposed method is applied to selected layouts to compare estimated average pillar stress values against values determined by detailed modelling and against observed behaviour.

May 3, 2023

The most important event in the Institute's recent history is the strategic plan, which was drawn up in 1986 during Henry James's term of office. This plan was formulated at a workshop attended by most of the senior members of Council, and from it has flowed a number of changes that have been introduced over the past four years.

Jan 1, 1990

By S. V. Lukichev, O. V. Nagovitsyn, V. V. Laptev

In this paper the authors describe the developed algorithms of short- and medium-term planning of underground mining operations. The algorithms were developed using the example of the flat-back cut-and-fill method, and provide multifactor accounting of mining conditions, technical and technological limitations: state and properties of the rock mass; the current mining situation; mining rules; availability of safety pillars; properties of the filling; additional characteristics of technological objects that complicate the driving of workings; sufficiency of human and technical resources; employee specialisation; existing machinery and equipment; opportunities and limitations of the transport scheme of the mine, and work schedule. The paper is presented by means of a dynamic model of mining development, which shows the sequence of mining operations in the mine workings. Besides animation, the tool provides an opportunity to form tabular and graphical reports.

Sep 1, 2021

Cutting strong rock with a drag bit assisted by high-pressure water jets By M. HOOD. B.Sc. Hons. (Min. Eng.). B.Sc. (Mech. Eng.). A.M.I.M.M. (Visitor) Experiments are described that led to the discovery that coherent high-pressure water jets directed immediately ahead of drag bits while they are cutting strong rock reduce the magnitudes of the forces on the bits significantly. Tests were carried out to assess the effects of the pressure of the water jets on bit-cutting performance. The pressure was varied between 10 MPa and 50 MPa, the water flow rate being a constant 30 I/min. Over this pressure range, the force on the bit was reduced to the extent that the depth of cut of the bit was at least doubled with the point of impingement of the jets optimized. Forces on the bit were found to be particularly sensitive to the point of impingement of the water jets relative to the bit. The optimum configuration was found to be with two jets, one directed towards each corner of the bit and impinging on the rock approximately 2 mm ahead of the leading edge of the bit. Experiments in which a drag bit and high-pressure water jets were used to cut strong abrasive quartzite in the underground mining situation have demonstrated a potential increase of up to five times in the average depth of cut due to reduction of the forces on the bit. The results from the underground tests indicate that the life of the bit is improved significantly - by a factor of approximately two - when highpressure water jets are used.

Jan 11, 1976

By C. F. Vos, J. D. Miller, J. C. Davidtz

"This work presents the potential for improving the flotation recovery of slow-floating sulphide minerals with the use of starvation dosages of a normal dodecyl (n-C12) trithiocarbonate (TTC) co-collector, together with a sodium isobutyl xanthate (SiBX) and dithiophosphate (DTP) collector mixture.At potentials below –150 mV (SHE), addition of nC12-TTC with SiBX improves the hydrophobicity of pyrrhotite, yielding captive bubble contact angles greater than those measured for SiBX or nC12-TTC alone, suggesting a low potential synergistic effect. This synergistic effect is further studied using Fourier transform infrared (FTIR) spectroscopy, the results indicating an increase in the surface concentration of the collector species when in a mixture. Thus, nC12-TTC with SiBX may act as an immobile surface anchor to which SiBX/SiBX2 molecules bond, increasing the localized concentration of collector species.Bench-scale flotation tests using mixtures of SiBX/DTP/nC12-TTC on a platinum group element (PGE)-bearing ore from the Bushveld Complex in South Africa confirm an improved metallurgical performance at very low substitutions (approx. 5 molar per cent) of SiBX. The improved recoveries for PGE, Cu, and Ni are correlated with improvements in the flotation kinetics of their slow-floating components. IntroductionShort-chain (less than C6) xanthates are very effective for the bulk flotation of sulphides (Fuerstenau, 1982), and early work (Leja, 1968; Gaudin, 1957; Plaksin and Bessonov, 1957; Taggart, Giudice, and Ziehl, 1934) indicated that the presence of oxygen in flotation slurries is necessary for the oxidation of the xanthate collector at the sulphide mineral surface to induce hydrophobicity. Fundamental research into the chemistry and adsorption mechanisms of xanthates over the years (Finkelstein and Poling, 1977; Woods, 1976; Winter and Woods, 1973) has revealed that for iron-bearing sulphide minerals, adsorption occurs predominantly through a charge transfer process. Oxidation of the adsorbed collector to the corresponding dimer takes place if the mixed potential of the system is greater than the reversible potential for dimer formation. In oxygenated slurries the rate of adsorption and oxidation of the collector depends greatly on the substrate surfaces. For chalcopyrite (Guler et al., 2005; Leppinen, 1990; Roos, Celis, and Sudrassono, 1990) and pentlandite (Hodgson and Agar, 1989) a two-step interaction with xanthate is proposed in which the chemisorbed xanthate is further oxidized to the dimer. The initial interaction of xanthate with pyrrhotite is through physisorption where xanthate physisorbs onto positive surface sites followed by oxidation to dixanthogen (Khan and Kellebek, 2004; Bozkurt, Xu, and Finch., 1998). This process is, however, slow and increased reaction time is needed to improve flotation recovery (Buswell and Nicol, 2002)."

Oct 1, 2018

By J. L. Louw

The utilization of centralized blasting systems is progressively becoming a feature of the South African mining industry, owing to increased pressure from the Department of Mineral Resources (DMR) to ensure safer blasting conditions. The purpose of a centralized blasting system (CBS) is to ensure reduced blasting-related incidents and to improve the underground working environment for the mine?s employees. The brief from Samancor Western Chrome Mines (WCM) pertaining to this study was to explore?at a conceptual level?all variables pertaining to the implementation of the CBS. Studies have indicated that Sasol?s SafeBlast? was preferred due to low overall risks and user-friendliness. Empirical observations, however, indicated that attention should be given to the current shaft-clearing procedure and to the installation of additional transformers. This is required to co-ordinate the power supply from 2 level to 10 level with the required supply of the network slave station. A cost analysis indicated that an electronically initiated CBS will result in a R24 cost increase per panel, which relates to a mere 1% cost increase per panel. This cost, in addition to the R1.1 million capital cost, proved to be negligible in comparison to the possible direct and indirect costs incurred by the mine in the event of a blasting-related incident. It was found that Samancor should conduct further studies incorporating the necessary requirements to ensure a successful transition, while considering all stakeholders on the mine. This study proved that the transition to a CBS would ensure safe and efficient blasting at Samancor?s Mooinooi Mine.

Jan 1, 2012

By D. Mjonono, S. T. L. Harrison, N. Maliela, A. Kotsiopoulos

The improvement of coal waste management practices, through the co-disposal of waste rock with sulphur-lean fine waste tailings (<1 mm in size), can potentially mitigate acid rock drainage (ARD). On exposure to natural oxidants, the sulphide compounds present in mine discards generate acidity, creating a cyclical oxidation process intensified by iron and sulphur oxidising microorganisms. To inhibit the emergence of ARD, a stable mine dump may be constructed that is structurally stable and incompressible through the mixing of complementary waste fractions that reduce voids and access to acid generating surfaces. However, large voids manifest as scale increases, due to decreased particle interlock, enabling the unrestricted access of oxidants leading to the early onset of ARD. To avoid this phenomenon, enhanced packing approaches based on geochemical and geotechnical characterisation tests were employed to improve bed stability. These were assessed for long-term prevention using aggressive oxidative conditions typical of heap leaching applications. Favourable results were obtained for both blended and multi-layered systems. However, long-term success was most notable in beds with alternating layers of waste rock and fine waste tailings with co-mingled systems being more susceptible to failure. Deconstructed co-disposed beds provided valuable insight into post-leach structural transformations. Results indicated that relative changes in initial coarse discards to fine waste ratios were most notable in blended systems. Mass fractions of the comparatively more mobile fine wastes increased axially down these test columns that ultimately resulted in increased contact of oxidants with the acid generating waste discards. Conversely, more consistent ratios were observed in multi-layered configurations. In these systems, near impervious hardpans were created by the moisture retaining fine tailings, forming stable structures with neutralising barriers sustained at each alternating layer. Consistent with post-leach geotechnical characteristics, static acid-base accounting tests showed that the uppermost sections of blended systems were more susceptible to oxidation due to structural failure with fine particles migration, while the more stable multi-layered configuration evenly maintained neutralising capacity. Keywords: Acid rock drainage (ARD), bed structure, mobility of fine particles

Jan 1, 2020

O.F.S. Branch Proceedings of the Annual General Meeting on Wednesday, 30th July, 1975 The Aromal General Meeting of the Branch was held at the St. Helena Club on Wednesday, 30th July, 1975 at 7.45 p.m. Mr D. A. Smith (Chairman) was in the Chair. There was also present: Professor R. P. Plewman, President of the S.A. Institute of Mining and Metallurgy. Conference on Vacuum Metallurgy The Fifth International Conference on Vacuum Metallurgy is to be held in Munich from 11th to 15th October, 1976. Excavation and tunnelling A conference on &apos;Rapid Excavation and Tunneling&apos; is to be held in Las Vegas from 14th to 17th June, 1976. Book reviews Mine filling. Queensland (Australia), Mt. Isa Mines, Limited, ] 973. 293 pp. $A20,00 incl. postage. Young, R. S. Cheml:cal phase analysis. London, Charles Griffin, 1974. 126 pp. £4.50. NIM reports Report no. 1714 The efficiency of the fire-assay procedure with nickel sulphide as the collector in the determination of platinum,silver, gold, and iridium. Report no. 1721 A preliminary investigation into the mechanism of depression in the flotation of sulphide minerals at the Prieska Copper Mine. Report no. 1725 The determination of silica in fluorspar by 14 Me V neutron-activation analysis. Report no. 1736 The determination, by atomic- absorption spectrophotometry and liquid extraction, of antimony (parts per million) in ores and concentrates. Report no. 1741 South African costs of equipment for the metall&apos;urgical industry(1975}. Report no. 1744 The refining of the platinum-group metals . Report no. 1746 The determination, by atomic-absorption spectrophotometry, of minor elements in zinc, lead, and copper sulphide concentrates. Report no. 1747 Magnetohydrostatic separation of gold from gravity concentrates. Report no. 1750 A review of the present and future development of sulphur production in South Africa. Report no. 1754 A new three-dimensional anodic electrode for reduced power consumption du,ring the electrowinning of metals. Report no. 139 A preliminary survey of goldrecovery problems arising in the production of pyrite. (9th Feb., 1967, re-issued Jun. 1975.) 16 pp. Report no. 140 A preliminary mineralogical investigation of pyrite from the K imberley and the Main Reefs, VogelstruisbuU Gold Mine. (13th Feb., 1967, re-issued Jut 1975.) 11 pp. Report no. 165 Gold recovery from pyrite flotation mill products by cyanidation. Progress made up to 1st May, 1967. (5th May, 1967, re-issued Jun. 1975.) 8 pp. Report no. 133 Gold recovery by cyanidation from mill products obtained after pyrite flotation. Progress made up to ht July, 1967. (18th Jul., 1967, reissued Jun. 1975.) 14 pp. Report no. 219 A review of some of the mineralogical factors influencing the flotation of pyrite. (29th Nov., 1967 reissued Jun. 1975.) 20 pp. Report no. 278 Gold recovery by cyanidation from mill products obtained after pyrite flotation. (24th Jan., 1968, re-issued Sep. 1975.) 51 pp. Report no. 306 The effect of preaeration on two samples of thickener under flow from the Venterspost Gold Mine. (30th Mar., 1968, re-issued Jul. 1975.) 14 pp. Report no. 317 Results of tests carried out at the Loraine Gold Mine during the period 5th to 7th February, 1968. (21st Mar., 1968, re-issued Jul. 1975.) 11 pp. Report no. 321 Aeration of ore from the Loraine Gold Mine before theaddition of cyanide.(17th Apr., 1968, reissued Jul. 1975.) 30 pp. Report no. 380 The effect of aeration, before cyanidation, of pulps of gold ores containing xanthate. (14th Aug., 1968, re-issued Jul. 1975.) 44 pp.

Jan 10, 1975

By D. Savile Davis

D. Savile Davis* (Member): The members of the Chamber of Mines Research Laboratories, headed by Dr Cook, indeed deserve all the plaudits that have been given for the original conception of the rock-cutter, and for the research work that has gone into designing the equipment now being tested. Underground trials with the rock-cutting machines at the Doornfontein Gold Mining Company Limited have been encouraging to the extent that 29 square fathoms of rock have been cut in the past three months with two modified prototype machines. Both the hangingwalI condition of the stope and the control of stoping width have been excellent. So far, however, the rate of production has been too slow and does not compare with conventional stoping methods, due firstly to the time-consuming operation of moving the machine forward and resetting it in its next cutting section and secondly to mechanical defects. Although great strides have been made in improving the tungsten carbide cutting tool, further progress is dependent upon engineering development in the design of a more reliable and versatile machine within economic limits. Commenting briefly on the experiments that have been carried out on the Gold Fields mines, the rock-cutter, when used at the Luipaards Vlei mine, some 600 ft below surface, cut very nearly perfect slots above and below the reef on a stope face but was unable to cut slots in the reef itself. At the Doornfontein mine, however, where the tests are currently being carried out at a depth of 8,000 ft below surface and where there is a much greater pressure acting on the rock face, vertical fracture planes can be clearly seen in the hangingwall running parallel to the face. Owing to the presence of these fracture planes it has been found impossible to cut slots of any depth and the action of the machine is more one of spalling than of cutting, resulting in slabs of combined reef and waste falling from the face as the cutting tool advances. This is accentuated by the existence of a well-defined hangingwall parting plane. Most of the slabbing takes place from the slot cut below the reef to the hangingwalI of the stope. Since waste sorting in narrow conditions and poor lighting is not an efficient operation, the reef together with a proportion of waste rock, has to be removed from the stope. The ripping action of the machine as opposed to slot cutting under these particular conditions may not be a great disadvantage, as the volume of waste which can be packed depends on the ratio of reef width to stope width and with a narrow reef body some waste has to be removed to the surface. In these circumstances mining at depth with this type of machine should not be viewed as selective mining but more correctly mining without explosives. Another type of rock-cutter is being tested by the Gold Fields Group, consisting of a diamond studded rotating disc, which has, to date, cut slots 10 ft in length and averaging 7 1/2 in. in depth. It is, however, too early to comment on the practicability and economics of such a cutter. The great interest that is at present being shown in breaking rock without the use of explosives warrants comment on the Robins raise-borer, recently introduced into South Africa, and used for the first time with great success at the Doornfontein mine.

By P. G. Henderson, G. C. Thompson

The organization and mechanized colliery management of a large by G. C. THOMPSON, B.Sc. (Min. Eng.) (Witwatersrand), M.B.L. (Member), and P. G. HENDERSON, B.Sc. (Min. Eng.) (Pretoria), M.B.A. (Member). Usutu Collieries Limited, at present the largest single producer of coal in South Africa, supplies Cam den power station. and produces 435 000 tonnes per month by conventional mechanized methods from bord-and-pillar workings in three mines. The thickness of the seams averages 2 metres, and the depth below surface varies from 15 to 150 metres. Each mine depends to a different extent on certain common facilities and services. Two of the mines are located on the same coalfield, and their rationalization would possibly be advantageous. Production policy is one of productivity with flexibility. The double-loader system is widely used, and one section at each mine is worked on single shift. Pillar extraction is practised where possible. In addition to lubrication and inspections, planned maintenance of mining equipment consists of sub-assembly replacements and overhauls. Conveyor and tractor/trailer transport is used underground. but trolley-wire locomotive haulage is being considered. The organization is such that co-ordination is relatively difficult, and certain changes could possibly improve the functioning of the engineering and mining departments. Technical and management training is carried out. Long-term planning will make use of a computer programme and will involve the investigation of other mining methods. Five-year and twelve-month plans are prepared, the planning of coal quality being based on the view that the mine and the power station together constitute a system. Control information systems make use of a remote computer terminal located at the mine. An improved integrated system is being investigated.

Jan 3, 1975

By P. G. Kovalchik

Overexposure to noise remains a widespread, serious health hazard in the US mining and other industries despite 25 years of regulation. Most categories of illnesses and injuries associated with mining have improved, with the exception of hearing loss. The drilling of rock in a confined work environment contributes to high levels of noise exposure in mining. The National Institute for Occupational Safety and Health (NIOSH) is conducting research to reduce the noise exposures of jackleg drill operators and to prevent additional cases of noise induced hearing loss (NIHL) by developing and evaluating low-cost retrofit noise controls for equipment. This report describes the procedure for the measurement and reporting of noise from portable pneumatic tools such as jackleg drills. The technique used in this research allows for the determination of the source A-weighted sound power levels and the radiation patterns in octave and 1/3 octave bands. Overall sound power level is also determined. This paper also reports the results obtained by using this procedure to evaluate a SECO S215 standard production drill and a CSIR Miningtek prototype rock drill incorporating engineering noise control measures. It was found that by using the manufacture?s recommended operating pressure of 496 kPa (72 psi) that the CSIR prototype?s sound power was 10 dB(A) less then that of the SECO S215.

Jan 1, 2009

By P. A. Laxen, P. J. van Staden

In situ leaching tests with thiourea as the lixiviant were caried out in two worked-out stopes at the No. 6 shaft at Rand Leases Gold Mining Company. Dissolution rates of 0,9 and 0,7 9 of gold per week per 100 m2 of footwal area were achieved. A major disadvantage of the method seems to be the slow rate of dissolution of the gold, which is probably caused by poor contact and slow mass transfer between the lixiviant and the gold surfaces. Under full-scale application, the loss of lixiviant by leakage could also be a very important factor. Furthermore, the oxidation products of thiourea may &apos;poison&apos; the activated carbon that is used for the recovery of the gold. The method may therefore be economically viable only in stopes that contain high values of residual gold.

Jan 1, 1989

By A. W. S. Schumann

G. H. HENDERSON INTRODUCTION It is a pleasure to have read Mr Schuman&apos;s wide ranging and highly informative paper and also to congratulate him. Before proceeding to give views on the use and preservation of coal in South Africa, it is perhaps apposite to look at the South African scene on the world canvas. Mr Schuman&apos;s figures in his Table I are highly revealing. The Table shows expected consumption, export and import demand in the year 1980 by the continents of the world. The Republic of South Africa is shown as one of only four exporting countries at that date, although in the interim, Australia has become an exporter and will continue to grow as an exporter of coal. Huge fields have been proved in recent years. There is reason to think that for some years, coal and its economical uses have been under-estimated. The importation of oil carries a constant question mark and the exciting possibilities expressed in the uses of Dranium a decade ago for power generation, appear to have met with some setback. Present indications are that breederreactors will be delayed until about 1990. The capital cost of such reactors, too, is enormous. By 1980 it has been estimated that 20 per cent of the energy required by the leading ten nations of the world will come from nuclear power, but 80 per cent would then remain for fossil fuels and hydro generation. COAL DEMAND AND USAGE It is of interest to record that coal production in all the countries of Europe has declined markedly in the last 25 years. This is due to competition from oil, gas and nuclear power and also for sociological reasons; but there are signs that efforts will be made to resuscitate, at least in some measure, the mining of coking coals for which there is a strong and growing demand. Possibly all hard coal now mined in Germany has coking properties and that country is self-sufficient in this commodity. Germany might perhaps consider selling coking coal to her neighbours and importing additional coal for power-raising purposes. It has been frequently stated in American publications that the coal reserves of the D.S.A. are sufficient for 1 000 years. What that means, I do not know, but it is at least an indication that America has huge reserves of coal. Domestic and export demand in the U.S.A. in 1968 exceeded production for the first time. In 1969, the United States&apos; output amounted to some 556 million tons, an increase of less than 2 per cent on the previous year. The output achieved fell short of demand, domestic and export, by more than 7 000 000 tons. This has caused and is continuing to cause anxiety in the U.S.A. In many countries young men for a number of reasons, largely environmental and social, are not coming forward in sufficient numbers for mining requirements and the same pattern has revealed itself in the Republic. This is, indeed, alarming because mining men in large numbers will be required to meet the estimated tonnage requirements set out in the following Table: It is difficult to visualise the replacement of these coal requirements either by oil or by nuclear fuels. The coal must be mined and men are required for the purpose. Unless a greater section of the population is allowed to participate in the more responsible aspects of mining, there is a serious likelihood that demand will not be matched by output. In addition to local demand, a lively export trade is possible. Exports are dependent on the future capacity of the South African Railways and Harbours and on Government policy. An export figure of 10000000 tons per year during the decade can be visualised and this figure would raise total estimated sales production to a figure of over 100 000 000 tons in 1980. At this point, it is necessary to examine the desirability or otherwise of exporting coal. How much coal

Jan 11, 1970

By J. le Grange, M. Tullmin, A. Strauss, F. P. A. Robinson, C. A. O. Henning

An experimental feritic stainless steel with a chromium content of 40 per cent was welded by laser and electron beam (EB) welding processes. These techniques were found to be particularly suited to the welding of this alloy in that the impact toughness of the weld metal and heat-affected zone (HAZ) of the laser welds compared favourably with those of the parent aloy. When the EB process was used, the impact toughness of the weld metal was over 180 J/cm2. Grain growth in the HAZ was minimal for welding with these two processes. Corosion tests, conducted in a solution consisting of 20 per cent sulphuric acid and 100 p.p.m. of potassium thiocyanate, and In a highly corrosive industrial solution, indicated that the laser and EB welds were free of sensitization effects, thus confirming the metalographic results.

Jan 1, 1989