Search Documents

By E. Keskinkilic

"Electrical steels are used in motors, power generators, and transformers for electrical applications owing to their superior magnetic properties. These properties are attributed to the presence of a significant amount of silicon in the steel composition. Silicon steels are mainly grouped into two categories: grain-oriented (GO) and non-grain-oriented (NGO). The Si content of silicon steels is generally between about 0.50% and 6.5%. Therefore, silicon steels are further classified as low-, medium-, and high- Si steels. In this paper, liquid steel processing practices for certain silicon steel grades are outlined by considering a steelmaking company that integrates a basic oxygen furnace (BOF), a ladle furnace (LF), and an RHtype degassing unit (RH). Possible problems are identified, suggestions are discussed, and conclusions are drawn on the basis of real plant data. IntroductionSilicon steels are widely used in motors, power generators, and transformers for electrical applications owing to their superior magnetic properties. They are mainly grouped into grain-oriented (GO) and non-grain-oriented (NGO) silicon steel grades. However, the differences in the properties and thermomechanical production of GO and NGO grades are outside the scope of this paper. In this study, liquid steel processing of certain silicon steels will be discussed. In the integrated iron and steelmaking process, converters are the primary steelmaking units that are used mainly for decarburization and removal of phosphorus, and for obtaining liquid steel with a specific chemical composition and suitable temperature for secondary steelmaking operations. Ladle furnaces are a type of ladle metallurgy station consisting of electrical and/or chemical heating facilities for adjusting the liquid steel temperature during alloying. Various types of vacuum units are used for decarburization and removal of nitrogen, hydrogen, and sulphur, depending on the metallurgical conditions of the vacuum units. In this study, an actual steel-production company is considered in which the primary steelmaking operation uses a basic oxygen furnace (BOF) converter with N2/Ar bottom blowing, and the secondary steelmaking operations involve (1) a ladle furnace (LF) heated by three graphite electrodes and equipped with Ar and N2 top/bottom mixing facilities, and (2) an RHtype (circulation) vacuum degassing unit equipped with a top-blowing attachment for oxygen blowing and an Ar-purging system from an up-leg snorkel."

Jan 1, 2018

By K. J. Kruger

Aluminium alloys have gained popularity in many industries due to their high strength and low weight. One shortcoming of aluminium alloys is their poor resistance to abrasion and erosion wear compared to materials such as stainless steels. In this project, aluminium alloy 2014 (AA2014) was coated with a 1.5 mm thick laser-deposited layer composed of silicon, copper, and aluminium with the aim of increasing the wear resistance. The amount of silicon, copper, and aluminium added to each sample was determined by a mixtures model. It was discovered that the Al-Cu system is very sensitive to silicon additions and that wear resistance depends on the primary phase to solidify as well as on the final phase distribution. Two primary phases were identified; alpha aluminium and theta intermetallic. It was observed that the clad layer increases both the hardness and wear resistance of AA2014, and that the material solidifying as primary alpha aluminium displayed a lower hardness but higher wear resistance than the samples containing primary theta phase. All clad layers performed better in terms of wear resistance than the unclad samples. The knowledge gained and principles used in this project could be applied to many other aluminium alloys.

Jan 1, 2014

By S. Polansky, J. Kolacz

The new sorting system has been developed to achieve efficient separation at low mineral content levels. The system employs high resolution X-ray sensors providing multi-energy analysis, thus giving maximal information about processed materials measurable by X-ray radiography. It makes it possible to analyse the internal structure of the particles and directly detect inclusion of minerals and metals like copper or gold. The paper describes sorting application examples for zinc, lead, copper and gold ore with low metal content below 0.1% of Cu. The sorting system still allows high efficiency analysis, quantification and removal of rock particles representing waste fraction with no metal or a negligible amount being uneconomic to process. This brings a huge advantage during pre-concentration, where almost no losses of valuable minerals in the waste fraction can be achieved. The presented sorting system has been developed by Comex and X-MINE EU Project Consortium. Keywords: X-ray sorting, ore sorting, XRF analysis, XRT analysis

Jan 1, 2020

By T. Steyn, M. Fofana

"One of the most important performance indicators of a dense medium cyclone (DMC) circuit is the Tromp curve, and by extension the separation density and Ecart Probable (Ep) values. The densimetric profiles of DMC product streams have been traditionally acquired using heavy liquid sinkfloat analysis, which has certain disadvantages, such as the associated safety and health risks. More recently, non-toxic media such as lithium hetero-polytungstates (LST) have been used, with the desired densities being achieved by maintaining the solutions at specific temperatures. However, the high costs of these liquids can be prohibitive. The long turnaround time of the sink-float analysis is a further disadvantage for timeous interventions to the operating set-points of the DMC process.The RhoVol technology can generate the density distribution of a batch of particles in a rapid, accurate, repeatable, and safe manner. Additional data of interest, such as particle size and shape, are also measured and reported on a per-particle basis. Furthermore, samples can be sorted into discrete sorting bins based on any of the measured parameters of the particle, making further analyses of the material possible.This technology has applications across all commodities that use the DMC, particularly in the size fractions –25 +8 mm and –8 +3 mm. To date, laboratory results have proved very encouraging – separation densities are within 5% of traditional sink-float results, and the technology is being introduced to diamond DMC plants. IntroductionDense medium separation is a commonly applied beneficiation technique for the density separation of valuable products from crushed ores. The industrial applications of dense medium separation have been summarized and reviewed by various authors (Scott and Napier-Munn, 2000; Bosman, 2014; Napier- Munn, 2018). Dense medium cyclones (DMCs) are widely used in the coal and diamond industries to produce clean coal or to preconcentrate kimberlitic ores, respectively. Cyclone performance (separation density monitoring) techniques are varied. In the mineral industry. Density tracer tests (Napier- Munn, 1985, 2014; Davis, Wood, and Lyman, 1985) without mineral material, are widely used, although their accuracy in predicting operating cut-points becomes limited once mineral material is introduced. More recently, radio frequency tracers have been also used for the determination of cyclone efficiency (Partition Enterprises, 2017)."

Feb 1, 2019

The Institute of Lighting Engineers of South Africa The Institute of Lighting Engineers of South Africa (ILESA) was constituted in May 1972 and now has over 70 members. The first Annual General Meeting was held on 15th August, 1973, at the Philips Auditorium, when the first presentation of membership certificates was made. Book Reviews Der Hochofenprozess. Das kinetischdynamische Simulationsmodell des Vereins Deutscher Eisenhiittenleute.Diisseldorf, Verlag Stahleisen M.B.H., 1973. Jones, M. H. and Woodcock, J. T. Ultraviolet spectrophotometry of flotation agents with special reference to the determination of xanthate in flotation liquors. London, Institution of Mining and Metallurgy. 1973. 25 pp. £2,50. Notice VI INTERNATIONAL CONGRESS OF ENGINEERS The above congress is to be held in Barcelona from 6th to 10th October, 1974. NIM reports Report No. 1568 A computer programme for the estimation of parameters in flotation. Report No. 1571 The commissioning of a direct-reading spectrometer for the analysis of silicate rocks by use of the graphite-pellet technique. Report No. 1579 The determination of tin tn geochemical- survey samples. Report No. 1587 A preliminary investigation of the flotation of copper-activated sphalerite without the use of collectors. Report No. 1589 Preliminary investigations into the flotation of tin dioxide, cassiterite, and some related gangue minerals. Professional . engineers Reference (18/19/1) 22nd November, 1973 Dear Sir/Madam, From time to time questions are being asked publicly concerning registration of professional engineers. These questions mainly concern the time it takes to finalise applications, especially those of applicants who do not hold a recognised engineering qualification. Professionele . . Ingenleors Verwysing (18/19/1) 22 November 1973 Geagte heer/dame, Van tyd tot tyd word daar vrae in die openbaar gestel oor die registrasie van Professionele Ingenieurs. Vrae gaan veral oor waarom dit so lank neem om aansoeke af te handel, veral van aansoekers wat nie 'n erkende ingenieurskwalifikasie besit nie.

Jan 3, 1974

By E. Saari, B. Musuku, K. Jansson

The quality of the concentrator plant process water is crucial for high performing mineral flotation circuits. Significant metal recovery and concentrate grade losses have been noticed particularly in more closed water loops. The recovery and quality losses have started to emerge mainly with decreased freshwater usage and because of changes in tailings management towards tailings thickening, paste, or dry stacking. These changes result in shorter, closed water loops with a rapid build-up of harmful components with negative impact on the beneficiation process. Consequently, water quality has a direct link to decreased product value and sales returns. Complete cleaning or water blending might not be the right way to achieve high recovery and high-quality products. Instead, the key is to understand what kind of water qualities are needed for the flotation of specific minerals. In this study harmful substances in various plant water streams were removed and/or modified by pilot-scale dissolved air flotation. Batch-scale mineral flotation tests with the untreated and treated water were then performed by using fresh ore samples and the plant’s own laboratory flotation procedure. The results indicate that because of dissolved air flotation, the mineral flotation recoveries were enhanced by 1‒3.3%. Keywords: Mineral recovery, metal recovery, mineral quality, process water, concentrator, beneficiation, mineral processing, flotation, process water treatment

Jan 1, 2020

A Colloquium and General Meeting was held jointly with the Mine Ventilation Society of S.A. in Kelvin House, Johannesburg, on 17th November, 1971, the theme being "The Economics of Mine Ventilation". Professor D. Howat (President) was in the chair. The Colloquium was attended by 150 delegates and was opened by the President at 9.00 a.m. MEMBERSHIP The President: "I have much pleasure in announcing that the names of the candidates, having been published in accordance with By-Law 5.2.2, Council has elected them to membership of the Institute in the following Grades: Fellows: Frederich-Wilhelm Volk, Peter Bennet Columbine. Members: Allan Colin Lawrence, Karel Anton van Gessel, Christopher Robert Harrison, Christopher Michael George Wartley, Frank Heinrich Deist, Ralph Morris, Benjamin Johannes Nolte. Associates: Wolf gang Freidrich Gottsman. TRANSFERS From Member to Fellow: Hugh Edward Keith Alien. From Graduate to Member: Errol Vincent Bosman, Christopher Roderick Stewart Needes, Bernard Wessels Holthousen. From Student to Graduate: David Robert Fleming. I welcome the new members to the Institute and congratulate them on their election. CO-OPTION TO COUNCIL The President announced that at the Council meeting held on 5th October, 1971, it was agreed, in terms of Rule 3.9 to co-opt Dr T. B. Beeton to Council. COLLOQUIUM The President welcomed visitors and members. He stressed that the discussion would be informal and that any contributor requiring publication should submit his contribution in writing. He then thanked the authors for providing pre-prints of the papers. After the President had concluded his opening remarks, he asked Professor J. de V. Lambrechts to act as Colloquium Chairman for the day and he, in turn, introduced the three Session Chairmen namely, Dr A. Whillier (Chamber of Mines and President of the Mine Ventilation Society); Mr M. Barcza (Managing Director, Corner House Laboratories); and Mr L. W. P. v.d. Bosch (Chief Consulting Engineer, Union Corporation). The following papers were presented: "Fan efficiency investigation on mines of the Union Corporation, Ltd." by J. A. Drummond. Published in the Journal Feb. 1972. "The design of underground cooling towers" by A. Whilliel'. Published in the Journal, Oct. 1971. "Some aspects of the design of cooling plant installations" by R. Hemp. Published in the Journal, Nov. 1971. "The planning of ventilation and refrigeration requirements in deep mines" by D. F. H. Grave and R. M. Stroh. Published in the Journal, Dec. 1971. "Cooling power of underground environments" by D. Mitchell and A. Whillier. Published in the Journal, Oct. 1971. At the conclusion of the three technical sessions the Symposium Chairman commented as follows, indicating that he would prepare a written summing up at a later stage: "The tone of the colloquium has had a sincerely practical note about it. It would have been a pity if the ventilation experts talked only theory and little practice. This practical theme has, I am sure, made the colloquium interesting to both ventilation men and others whose daily tasks do not touch so closely on this fascinating subject. This practical theme was in evidence through all the papers and contributions. Some of you may have felt that there was not enough emphasis on the word 'economics' as advertised in the broad title of the colloquium. I do not think this was really a valid criticism because as someone said 'it all boils down to Rands in the end!' So whether it was a case of low fan efficiency, poor design of cooling towers, wrong planning or low human efficiency due to high heat stress. . . it all boils down to money saving and therefore economics, whenever improvements are forthcoming. The title of the colloquium was thus not misplaced. The views of senior mining men on the production side are appreciated. Let us say that this exchange of views between ventilation engineers and those who have to take the final decisions and spend the money, should prove to be most rewarding." Professor Lambrechts finally thanked the Session Chairmen and everybody who had helped to make the colloquium a success and the meeting closed at 4.0 p.m. In a subsequent written summing up, the Colloquium Chairman gave the following as his impressions of some of the highlights which emerged from the papers and discussion thereof: (The names indicate the authors only). Drummond: It was hinted that the time had arrived to consider the introduction of a South African fan test code which would be better suited to local conditions than the currently acknowledged B.S.S. code which, however, is seldom enforceable in practice. In this connection also, there was prominent reference to the thermodynamic approach of McPherson. Wide variations in the quality of maintenance of, and repair work on, fans were stressed. It was mooted that ventilation engineers responsible for estimating the basic duty specifications for large fans, frequently played safe by overestimating the pressure required, thus ensuring that there would not be a shortfall in air volume delivered. This usually meant reduced fan efficiency and it was suggested that decision makers seemed to lay more emphasis on volume of air delivered than on real eco-

By R. T. Rudd

The impact of slimes-dam formation on water quality and pollution by R. T. RUDD*, B.Sc., AMI (S.A.) CE (Visitor) This paper discusses the mechanics of pollution by slimes dams in the gold- and fluorspar-mining industry, as well as that caused by coal dumps and slurry dams. The effect of coal mining on two typical rivers in Natal is shown and the implications discussed. The implications and trends of sulphates pollution on the Rand Water Barrage in the Vaal River are discussed. The spread of pollutants (sulphates and fluorides) from the Reef and elsewhere, and the impact on urban use and agriculture downstream of the barrage, are illustrated. Conclusions and future policy are outlined.

Jan 12, 1973

By P. J. Petit

"The complex planning required to achieve any planned production yields multiple and dissociated responses over the life of project (LOP). The customary decision-making process negates the possibilities of developing optimized and integral solutions from operating levels up to business and strategic levels. This results in an inefficient project or overall underperformance of the operation.In the project setting, disconnected trade-offs and improved performance studies become inadequate, because they are site-specific and use only a few comparative parameters. They are often based on a small data-set.Decisions taken to achieve overall objectives require the correct determination and dissemination of key performance indicators (KPIs). The KPIs indicate efficiency in operation, whereby the marginal rate of technical substitution corresponds to the rate of production. It is the necessary condition for optimization. Performance realization for sustainability follows optimization modelling, the latter often being presented with financial results such as business net present value (NPV). It considers techno-financial constraints and provides a strategic and aligned outlook of KPI decisions for an enhanced and integrated outcome.This paper explains a mining case study that is rendered efficient, and through business optimization (BO) short-term and sustainable targets are reached. Business optimization increases the NPV by 14.7%. This is achieved by challenging conventional decision-making associated with maximizing business value by including environmental externalities within the LOP."

Jan 1, 2016

By L. A. Cornish, J. W. van der Merwe

"The hydrofluoric acid (HF) industry in South Africa uses normalized mild steel (SA 516 Gr 70) for the storage and distribution of its technical-grade product (70% HF). The technical-grade acid is split from the anhydrous hydrogen fluoride (AHF) product during distillation just after HF is produced, in a stainless-steel-lined kiln, from the reaction of calcium fluoride (CaF2) with sulphuric acid (H2SO4). Uniform corrosion of the storage tanks is mitigated during commissioning by contacting the steel with 70% HF. A corrosive reaction takes place (2H+ + 2F- + Fe - H2 + FeF2) to form scale inside the tank which diminishes the attack of the steel by fresh HF, thus prolonging the service life expectancy of the vessels. This iron fluoride scale in the vessel grows continually, resulting in corrosion of the vessels continuing at a predictable rate (approx.0.5 mm/a) since the first commissioning of the tanks at Necsa in 1993. In early 2012, an increase in the average corrosion rate of the tanks to 3 mm/a measured at and below the liquid band in the storage vessels was noted. Three months later the corrosion rate had increased to 30 mm/a, just before the first leak from the tank was detected. The tanks were decommissioned shortly afterwards and an investigation revealed that the rapid corrosion was due to the presence of increased levels (>50 ppm) of nitric acid (HNO3) in the tanks, which attacked the fluoride layer protecting the steel.The oxidation characteristics of high concentrations of HNO3 with low concentrations of HF on stainless steel surface treatment are well documented. The effects of low levels of nitric acid on the corrosion of steels in sulphuric acid are also known, but no suitable published data currently exists on corrosion by high HF concentrations with low HNO3 concentrations. Establishing the rate and mechanism of corrosion by HNO3 (0.1 to 1%) in 70% HF is currently a high priority for the HF industry in South Africa and will become increasingly important in the near future due to depleting fluorite reserves and cheaper, but less efficient, processes producing H2SO4 with higher impurity levels, which were not anticipated in the original plant design. The aim of this study is to simulate the corrosion conditions in the plant on a laboratory scale in order to establish the corrosion characteristics of the steels used in the HF plant, which are increasingly exposed to the HNO3 impurities that tend to concentrate in the final technical-grade HF acid product."

Jan 1, 2016

Council and Standing Committees, 1977-1978 President: P. A. von Wielligh. Vice-Presidents: Dr M. G. Atmore and D. A. Viljoen. Honorary Treasurer: J. K. E. Douglas. Immediate Past President, Dr M. D. G. Salamon. Members of Council: J. D. Austin, A. N. Brown, A. A. Hazell, Dr P. R. Jochens, Prof. R. P. King, Dr D. G. Krige, Prof. F. Q. P. Leiding, D. G. Malan, J. C. Mostert, H. G. M. Rose, W. T. Ruhmer, A. A. Sealey, R. A. von Maltitz. Chairman, Witbank-Middelburg Branch: T. S. Wilmot. Chairman, Orange Free State-Klerksdorp Branch: A. N. Shand. Past Presidents Serving on Council: R. J. Adamson, H. Britten, J. K. E. Douglas, Prof. D. D. Howat, Dr J. P. Hugo, D. G. Maxwell, Prof. R. P. Plowman, Dr R. E. Robinson, P. W. J. van Rensburg. Standing Committee Chairmen: Membership, D. A. Vil¬joen; Technical Programme - Metallurgy, Dr P. R. Jochens ; Technical Programme - Mining, Dr D. K. Krige ; Vacation School - Metallurgy, Prof. R. P. King ; Vacation School - Mining, Dr M. D. G. Salamon; Awards, Dr M. D. G. Salamon; Excursions, Dr M. G. Atmore; Adjudication, Dr M. D. G. Salamon; Consti¬tution, Rules, and Policy, Dr M. D. G. Salamon; Mines and Works, P. A. von Wielligh ; Education, Dr M. D. G. Salamon; Monograph Series, Dr R. E. Robinson; Phoenix National Committee, Dr R. E. Robinson ; Pyrometallurgical Discussion Group Convenor, Dr J. B. See/Dr D. I. Ossin.

Jan 1, 1979

By J. O. Roux

The Impala Platinum Limited Base Metals Refinery in Springs, South Africa, refines convertor matte containing base metals and PGM?s (platinum group metals) using a hydrometallurgical process. In addition to a PGM-rich concentrate that is further refined, the Base Metals Refinery produces nickel (in powder or briquette form), copper cathodes and cobalt powder. Five leaching stages are utilized to remove the base metals and impurities from the PGM concentrate. The project described in this paper involves a radical redesign of the second stage leach autoclave with the aim of reducing maintenance costs and downtime, increasing throughput and ensuring a safer working environment. The second stage leach process at the Base Metals Refinery, produces a PGM-rich residue through the extraction of copper and any remaining base metals from the first stage leach solid residue material. Leaching is performed in an autoclave operating at a pressure of 600 kPaG and a temperature of 140°C to 150°C. Concentrated H2SO4 is added to the feed to produce a solution with a free acid content between 10 and 30 g/L and a pH of less than 2. Oxygen is passed into the 1st and 2nd compartments of the autoclave. As a result of the aggressive, highly oxidizing conditions within the autoclave, the original design utilized a heavy wall carbon steel shell with lead lining and two layers of acid bricks. The bricks acted as a wear resistant material and ensured a low surface temperature at the skin of the lead lining, whereas the lead lining acted as a corrosion barrier to protect the steel shell. These brick lined autoclaves were heavy, maintenance intensive and prone to catastrophic failure. A radical autoclave redesign was needed to reduce the high costs of manufacturing, installation and operation. Finite element modelling was used to optimize the design and various high alloy materials were investigated for the application. Based on extensive test work, the carbon steel shell was replaced with duplex SAF 2205 stainless steel in the new design. The use of this highly corrosion resistant material, eliminates the need for the lead and brick linings and reduces the wall thickness requirements substantially, resulting in an increase in the available volume for the same external shell dimensions. The vessel is welded in circular sections to form an elongated, impermeable, cylindrical body, with several agitator nozzles and compartments. The first new duplex stainless steel unit has been in continuous operation for more than 24 months and its performance has exceeded the highest expectations. The design was so successful that a patent has been registered. The major benefits of the new stainless steel design include increased throughput, improved performance, less downtime and a safer working environment. Lead has been eliminated and replaced with a more environmentally safe material, and the total lifespan of the vessel has been extended. In addition, the autoclave project has made significant developments in advancing the field of welding and optimizing the integrity of welding quality standards in South Africa.

Jan 1, 2009

By M. Shaw, H. R. Heydenrych, A. E. Lewis, E. Glass, J. Chivavava

The removal of calcium from the retentates of reverse osmosis (RO) treated minewater is desirable since it allows the recovery of both additional potable water (through RO) and higher-purity salts (in downstream processing). This, in turn, reduces the need for costly and unsustainable evaporation ponds and enhances the economics and operability of potential zero-liquid discharge downstream processes, e.g. evaporative-, cooling- and eutectic freeze-crystallisation. For this study, a multi-component retentate high in sodium content was considered, typical of those emanating from minewater reclamation plants in Mpumalanga, South Africa. Four technologies were evaluated to remove calcium: gypsum precipitation by addition of lime; calcium carbonate precipitation by addition of soda-ash; heating crystallisation of calcium sulphate anhydrite; and cooling crystallisation of gypsum. Full processes were developed and simulated using electrolyte thermodynamics. Using the results of these simulations, capital- and operating costs, as well as revenues were calculated and used in economic comparisons of the processes. Sensitivities to key purchasing and selling prices were also investigated to understand the impact of changes in these variables. For the case of a low magnesium-to-sodium ratio in the feed, gypsum precipitation through lime addition was found to have the lowest operating and total annualised costs; but, if revenue could be derived from the sale of sodium sulphate, calcium carbonate precipitation through soda-ash addition was favoured. Keywords: Calcium removal, gypsum precipitation, calcium carbonate precipitation, heating crystallsation, cooling crystallisation, economic comparison

Jan 1, 2020

By K. C. Naidoo

There are two main types of densifying cyclones currently available in the market, namely polyeurethane (PU) and ceramic. The PU densifying cyclones are currently used throughout the Grootegeluk complex and coal beneficiation in general. It has been identified that PU densifiers wear relatively fast depending on the operating pressure and need to be replaced frequently as a result. The motivation for this paper is to achieve an increase in the densifying cyclone lifetime through less wear and an increase in efficiency resulting in the ability to build higher relative densities (RD) more quickly. This will allow for a reduction in downtimes due to replacing densifying cyclones as well as building RD and a reduction in the operating costs associated with replacing worn densifying cyclones. Some of the major findings of the study indicated that the ceramic cyclone theoretically undergoes less wear than the PU cyclone, but since wear is application-specific and was evaluated, the wear on the polyurethane cyclone was found to be minimal. The RD differential is higher on the PU cyclones than the ceramic cyclones, showing that the PU cyclones perform better in a densifying application. This is the first test conducted on this application and type of cyclones. It should therefore be noted that having the PU cyclone significantly outperform the ceramic cyclone was not expected, due to the only change being the material of construction. This is an indication to take the material of construction into account when selecting cyclones as it can have a significant impact on the cyclone performance in specific applications. Keywords: Ceramic, cyclone, densifying, density, dense medium, polyurethane, wear

Jan 1, 2020

By J. W. Latilla, J. J. van Wijk

In late 1997 a request was received to assist with determining the powered support unit (shield) load capacities for the planned 2 seam short wall. This project had a number of aspects which made it attractive to utilize numerical modelling in conjunction with other more conventional design tools in the design of the shields. Amongst these were: The 2 seam panels were to be laid out about 25 m below the previously short walled 4 seam, the 4 seam had in turn been over-mined by the 5 seam long wall, the proposed face height of the 2 seam short wall was 5.5 m while the 4 seam had been mined at 4 m. The top seam in the area (5 seam) had been mined at between 1.5 and 2.2 m high, the face conditions with about 95 m of broken material applying dead weight loading to the 2 to 4 seam inter-burden septum were hard to predict and cyclical loading due to the presence of strong sandstone bands in the 2 to 4 seam inter-burden. The basic thrust of the study was to take the known, and successful, situation (4 seam short wall) and carry out comparative modelling to enable prediction of likely 2 seam conditions. Some two dimensional aspects studied were: 5 m goaf hanging up behind shields, stresses in beams to determine likely first goaf roof span, stresses in cantilever beams to asses cyclical loading due to sandstone bands in the interburden being loaded by the overlying goaf and stresses on chain and crush pillars adjacent to the goaf edge. Three dimensional aspects that were investigated included: Load distribution along face for close goafing and 5 m goaf hang-up and load in a 1 m wide rib modelled in the position of the powered support units. From the modelling it was possible to determine the optimal shield leg capacity of the new 2 seam equipment. These outputs were used when drawing up the technical specifications for manufacture of the new equipment. The face was successfully commissioned in August 2002. Fin 1997, requête fut faite pour aider à la détermination des capacités de charge pour l’unité de soutènement mécanisée (bouclier) pour la couche 2 courte taille en projet. Certains aspects de ce projet le rendaient intéressant pour utiliser la modélisation numérique en même temps que d’autres méthodes conventionnelles pour la conception des boucliers. Parmi ces aspects se trouvaient : Les panneaux de la couche 2 devaient être placés environ 25 m au dessous de la couche 4 courte taille ; la couche 4 avait été remplacée par la couche 5 longue taille ; la hauteur de taille proposée pour la couche 2 courte taille était 5.5 m, tandis que la couche 4 avait été exploitée à 4 m. La couche supérieure de la région (couche 5) avait été exploitée entre 1.5 et 2.2 m de hauteur ; il était difficile de prédire les conditions de taille, avec environ 95m de matériaux cassés ajoutant une charge morte à la plaque de séparation entre les couches 2 et 4 et un chargement cyclique causé par des bandes de grès dans l’entre-fardeau 2-4. L’idée principale de l’étude fut de prendre la situation connue et réussie (couche 4 courte taille) et de faire une modélisation comparative pour prédire les conditions probables de la couche 2. Certains des aspects à double dimension qui furent étudiés étaient : Un accrochage de remblai de 5m derrière les boucliers ; contraintes dans les poutres pour déterminer le premier intervalle probable entre remblai et toit ; contraintes dans les poutres en porte-à-faux pour évaluer le chargement cyclique causé par les bandes de grès dans l’entre-fardeau qui est accablé par le remblai et les contraintes sur les piliers par chaîne et d’écrasement adjacents au bord du remblai. Aspects à trois dimensions qui furent étudiés : Distribution de la charge le long de la taille pour les remblais proches et l’accrochage de remblai de 5 m et la charge dans une nervure de 1 m de large modelée dans la position des unités de soutènement mécanisées. La modélisation a permis de déterminer la capacité de portée optimale du bouclier du dispositif nouveau pour la couche 2. Ces résultats furent utilisés pour dresser les spécifications techniques pour la fabrication de l’équipement nouveau. La taille fut commissionnée avec succès en août

Jan 1, 2003

By M. J. U. T. Van Wijngaarden

SYNOPSIS The corrosion characteristics of a new steel, 14Cr, which is a modification of the well-known 3CR12, in aqueous sulphate solution were studied through polarization diagrams and a computer analysis based on the polarization¬resistance technique. It was found that the corrosion rate of 14Cr steel is independent of pH for pH values above 6, but, below a pH value of 4, the corrosion rate increases sharply with decreasing pH. In air-saturated solutions of neutral and mildly alkaline pH, the corrosion rate is approximately 60 µm per year. The 14Cr steel shows a twentyfold improvement in corrosion resistance over that of 3CR12 in sulphate solutions at pH 2,0. This is considered to be due to the beneficial effect of its higher chromium and nickel contents.

Jan 1, 1985

By E. Emami, J. Valencia, J. Sattarvand

The knowledge of the final location of a drillhole is critical in obtaining the expected blasting results. This paper proposes a new methodology to control the drilling accuracy in open-pit mines using aerial images and machine learning. Specifically, it investigates how support vector machines (SVM) and convolutional neural networks (CNN) are useful for automatically detecting blastholes over drone images captured in blasting patterns. Several datasets were obtained from different mines in Nevada (USA) and were used to train and test models. We then processed those images to create orthomosaic and digital elevation representations of the patterns. Thousands of patches were then extracted and augmented to develop SVM and CNN models. The results demonstrate that machine learning is useful for drillhole detection and, in this way, to control the drilling accuracy and use the explosive energy more efficiently.

Sep 1, 2021

By C. D. Winkler

Vanadium-based sulphuric acid catalyst has been utilized to oxidize SO2 to SO3 since the early 1900s. This versatile product displaced the expensive and easily poisoned platinum-based catalyst in nearly all applications by the 1930s. MECS has been manufacturing the vanadium-based catalyst since 1925 and today is the leading supplier in the world of sulphuric acid catalysts in a variety of forms. Currently, MECS has worldwide customer/technical support for the catalyst as well as a dedicated catalyst manufacturing plant in Martinez, California. MECS also has a strong technical and research and development programme dedicated to creating new and improved products and services. This paper will describe some of the technical details of vanadium-based sulphuric acid catalysts as well as offering a unique look into how caesium-promoted MECS catalysts can be used in single and double absorption acid plants, and off-gas plants running on irregular gas feeds, to reduce emissions and preheater run times. An update on MECS technical services extended for use in characterizing converter performance is also presented.

Jan 1, 2009

By S. Swanepoel, A. V. Cherkaev, Q. G. Reynolds, M. Erwee

Ferrochrome (FeCr) is a vital ingredient in stainless steel production and is commonly produced by smelting chromite ores in submerged arc furnaces. Silicon (Si) is a componrnt of the FeCr alloy from the smelting process. Being both a contaminant and an indicator of the state of the process, its content needs to be kept within a narrow range. The complex chemistry of the smelting process and interactions between various factors make Si prediction by fundamental models infeasible. A data-driven approach offers an alternative by formulating the model based on historical data. This paper presents a systematic development of a data-driven model for predicting Si content. The model includes dimensionality reduction, regularized linear regression, and a boosting method to reduce the variability of the linear model residuals. It shows a good performance on testing data (R2 = 0.63). The most significant predictors, as determined by linear model analysis and permutation testing, are previous Si content, carbon and titanium in the alloy, calcium oxide in the slag, resistance between electrodes, and electrode slips. Further analysis using thermodynamic data and models, links these predictors to electrode control and slag chemistry. This analysis lays the foundation for implementing Si content control on a ferrochrome smelter.

Mar 14, 2024

By L. Zhou, J. Qiu, M. Tang, J. Wang, G. Dai

Coal spontaneous combustion in longwall gobs is a major concern in coal mines. In comparison to other hazards, this phenomenon is difficult to detect. Fifteen factors influencing coal spontaneous combustion in longwall gobs were identified from the literature. The logical relationships between these factors were evaluated and quantified by decision-making trial and evaluation laboratory (DEMATEL) and interpretive structural modelling (ISM) methods. A four-level hierarchical structure model was established. The research shows that combining DEMATEL and ISM can reveal the key factors that influence coal spontaneous combustion in longwall gobs and establishthe interactions and relationships among these factors. The results can provide the basis for preventing and controlling coal spontaneous combustion in longwall gobs.

Jun 10, 2024