Search Documents

By A. F. Colombo

In an effort to maintain an adequate supply of iron to meet national economic and strategic needs, the Bureau of Mines, U.S. Department of the Interior, is conducting research on methods for beneficiating the oxidized taconite resources located on the western Mesabi range in Minnesota, thus expanding domestic iron ore reserves. The selective flocculation and cationic flotation process was investigated in a pilot plant using an ore feed rate of 410 kg/hr (900 1b/hr) and 88 percent recycled water. Lime and a cationic flocculant were used to clarify the waste slurries treated in the water reclamation circuit. An oxidized taconite assaying approximately 36 percent Fe yielded concentrates averaging 63.5 percent Fe and 4.3 percent SiO2 and having an average iron recovery of 84.4 percent. The estimated reagent cost per tonne of concentrate was approximately $1.10. In an attempt to recover more of the iron lost in the flotation tailing, wet high-intensity magnetic (WHIM) separation was incorporated in the pilot plant circuit. The flotation concentrate grades obtained from beneficiation circuits with and without WHIM scavenging were similar, but when WHIM separation was used the overall iron recovery was increased by 2 to 9.5 percent, depending on the iron assay of the flotation tailing.

Jan 1, 1978

By R. V. Ramani, R. Bhaskar

"One of the primary means of control of health hazards from respirable contaminants in mine atmospheres is through design and operation of mines to meet mine health and safety regulations and recommended practices. A U.S. National Academy of Sciences study concluded that for significant progress in coal mine dust control, research should be directed more toward obtaining fundamental understanding of the origin, transport and characteristics of respirable coal mine dust. Theoretical and experimental studies on transport of dust · in mine airways, particularly coordinated efforts to validate theory with practice, are scarce. Some empirical models, developed on the basis of experimental data, are available but these models cannot be applied to new conditions. The purpose of this paper is to present the results of theoretical and experimental studies on the transport and deposition of dust in mine airways. This study is a part of an ongoing research project in the Generic Mineral Technology Center on Respirable Dust.In the paper, the assumptions of the modeling phase of the project and the development of a convectiondiffusion equation for dust transport in mine airways are outlined. The important aspect of the modeling effort is the capture of the deposition phenomenon. The experiments performed under controlled conditions in a typical mine airway, as well as under normal mine operating conditions, are discussed. The comparison of the model predictions with experimental results are made to identify critical areas of agreements and deviations. The implications of the findings and areas for further research and development are presented."

Jan 1, 1990

Develop a user-friendly computer program that permits those interested in mine health and safety to access and analyze on a personal computer (PC) employment, production, and accident data for U.S. coal and metal-nonmetal mines. This software is being designed with a major focus on flexibility and case of use. The Mine Accident Decision Support System (MADSS) will be available for distribution in mid-1994. Currently, the U.S. Bureau of Mines (USBM) is seeking volunteers willing to pilot test a preliminary version of the software and to provide suggestions for its improvement. Background Since 1975, the Mine Safety and Health Administration (MSHA) has compiled large data bases of information about U.S. mines and the reportable accidents, injuries, and illnesses that have occurred in those mines. Employment and production data arc collected on a quarterly basis from each mine and accident information is collected on an incident -by-incident basis. The USBM has compiled estimated costs for each of these accidents using computer models. All of this information is potentially useful to mine health and safety researchers. However, it has been underutilized because it is stored in large mainframe data bases that arc inaccessible to many users and/or are cumbersome and difficult to use.

Jan 1, 1993

By Wilbur I. Duvall

In a previous report, entitled A Gage and Recording Equipment for Measuring Dynamic Strain in Rock, a control circuit for a drum camera was described. The purpose of this control circuit was to provide a means for firing seismic caps, synchronizing the firing of the cap with the opening of the camera shutters and generating an electrical impulse at the instant of detonation. The operation of this circuit depended on the following two characteristics of seismic caps: (1) these caps contain a bridge, which breaks at the instant of detonation, and, the firing delay time of the cap is a function of the firing current. During the course of the Bureau's studies, considerable difficulty was experienced from "firing hash", i.e., spurious vibrations that appeared on the records at the time of detonation. The cause of most of this "firing hash" was traced to the intermittent grounding of the cap leads at the time of detonation. As the cap leads were still connected to the firing battery, the grounding of the leads permitted current to flow through the rock to the gage and to return to the firing battery through the shield on the gage cables. The intermittent flow of current along the cable shield produced potentials on the gage leads that were recorded as the "firing hash." To eliminate this difficulty, it is necessary to remove the firing voltage from the cap leads the instant the cap detonates. This report supplements the previous report and describes an improved circuit that can be used to fire seismic caps, remove the firing voltage from the cap leads the instant the cap fires, control the firing delay time in the cap, and generate reference signals at the time current starts flowing in the cap circuit and at the time the cap detonates. These reference signals can be used to determine the firing delay time of seismic caps and the time at which the seismic wave is generated by the explosion.

Jan 1, 1950

At the present time many coal preparation plants handle coal-clay wastes in one of two methods. In one method, the waste is processed in a thickener, followed by further dewatering through filtration, and subsequent blending with coarse waste refuse from the preparation plant. The resulting mixture is then disposed by stacking it in available storage locations. The coal-clay waste is often reslurried by rain or water from other sources, causing a potentially unsafe situation such as mud flows. The other method often used requires thickening and impoundment of the thickened slurry behind earthen dams which poses safety risks if structural failure of the dams occurs. To overcome these two problems, a flocculation method was developed which produces a stable agglomerated material resistant to reslurrying. How It Works The new method involves treating coal-clay waste with lime to raise the pH and flocculating the slurry with a nontoxic polymer of polyethylene oxide. The resulting floes are dewatered on a static screen and agglomerated. For extremely fine waste, further dewatering of the material is accomplished on a rotary trammel screen. The dewatered material may be ponded or mixed with coarse waste from the preparation plant to produce a stable mixture that can be stacked.

Jan 1, 1985

Reduce mine worker dust exposure by capturing airborne coal and quartz dust generated by a continuous mining machine. Approach Install a water-powered scrubber system operating at 1,000 psi on the side of a continuous miner boom. Dusty air under the boom is drawn through the scrubber, and cleaned air is discharged into the face return. How It Works Most coal mines use exhaust face ventilation to send fresh air over the miner operator, and contaminated air behind the line curtain to the section return. The difficulty with exhaust face ventilation is that the line curtain should be within 10 feet of the face for maximum effectiveness. If the line curtain is not extended properly, or water sprays for dust control are poorly installed, dust rolls back toward the operator. A scrubber mounted on the mining machine will effectively reduce this dust rollback and the dust in the return airstream.

Jan 1, 1989

By J. B. Littlefield

The term "konimeter" is used generally to designate a type of dust-sampling instrument that collects the dust from a small volume of air by impingement on a glass plate prepared aced with an adhesive film. The konimeter was first developed by Sir R. N. Kotze about 20 years ago and was followed a few years later by the circular-type konimeter, by which a number of samples may be collected on a glass disk. The present discussion will be confined to the circular type, as it is used most. Various techniques have been developed for using the konimeter, and many materials, such as petrolatum, mineral oil, and glycerine jelly, have been used in preparing the adhesive film. In South Africa, Australia, and Canada, where the konimeter has been employed most widely, dust samples are treated by ignition and washing before being counted. In Canada the dust samples are collected on a disk of special heat-resistant glass prepared with a film of mineral oil; the disk is then heated to a dull cherry-red in a muffle-furnace to remove the film and organic matter, cooled, and washed with a few drops of 50-percent hydrochloric acid followed by distilled water and alcohol, and then heated again to remove residue left by evaporation of the alcohol. After this treatment, the dust samples are counted under a magnification of 150 diameters with dark field illumination.

Jan 1, 1938

Improve face ventilation in mines with large cross-sectional entries. Approach Oil shale, salt, and limestone mines typically have large entries. Providing adequate airflow to the working faces of such mines for worker comfort, health, and safety is a substantial ventilation problem. If diesel equipment is used at the face or if a methane hazard exists in the mine, the problem becomes even more complex. To address this problem, a study was conducted under a joint contract between the Oil Shale Committee of the Colorado Mining Association and the Bureau of Mines. The study evaluated two face-ventilation concepts for large-entry mines. Improving Ventilation Two face-ventilation systems were selected for testing of an oil-shale mine, based on results of a cost/benefit analysis. The systems were a free-standing jet fan and a ducted fan operating in the blowing mode. The jet fan was spotted on the intake side in the mouth of the entry being advanced with final positioning, in or out, deter-mined by minimum recirculation. The ducted fan was also positioned in the mouth of the entry being advanced, with its tubing terminating 75 feet from the working face. The mine face entry was a dead heading 55 feet wide, 30 feet high, and 320 feet long. Sulfur hexafluoride (SF.) tracer gas was used to measure the performance of the two systems in diluting mine face pollutants including after-gases from blasting, hot diesel emissions, methane roof layers, and methane emitted from muckpiles.

Jan 1, 1987

Generate less respirable dust during mining by reducing the clogging and downtime of the water sprays on mining machines, especially on continuous miners. Approach An improved filtering system, having commercially available components, has been designed and tested. How It Works The improved filtering system shown opposite is mounted on the mining machine, where It traps particles of coal and pipe scale which cause most clogging of the water sprays. Water entering the system first flows through a ?Y" strainer, which screens out particles larger than 1/8 inch diameter. Next, the water whirls through a small hydrocyclone. Most of the remaining smaller particles are removed and pass Into the accumulator compartment built into the hydrocyclone. The water also flows through a final filter. This filter catches particles that might pass the hydrocyclone, especially during water spray start-up and shut-down, when the speed of the water flow is not sufficient for

Jan 1, 1976

Control respirable dust in underground coal mines through selection of optimum water spray pressures. Approach Through underground trials at longwall and continuous mining operations, the relationship between operating water spray pressure and respirable dust levels at the machine operator's location was determined. Defining the Application Water sprays are used for two significantly different control applications. On longwall mining machines, sprays are commonly installed both on the body of the machine and on the cutting drum. Sprays on the body of the machine are used to redirect dust which has already become airborne away from the machine operator. Each spray acts as a small fan, directing the primary airflow over and around the machine and towards the face, away from the operator. The energy of this system is directly related to the spray pressure. Higher pressures move more air, but care must be taken not to cause turbulence and boilout into the walkway. Sprays mounted on the drum are, effective at suppressing the respirable dust at the bit/coal interface and preventing it from becoming airborne. Again, these sprays must not impart excessive energy to the dust particles thus stirring up more dust than they suppress. While mounting sprays on the shearer drum is standard industry practice, there is no reliable technology available to successfully mount water sprays on the cutting drum of continuous miners. Instead, sprays are mounted on the machine body, close to the drum, and directed at the cutting head. This allows the water to reach the bit/coal interface and mix with the cut material. Here again, care must be exercised to prevent these sprays from imparting excessive energy to the dust particles and stirring up more dust than they suppress. These sprays can also cause dust "rollback" from the face, toward the operator, if operated at too high pressures.

Jan 1, 1986

"Fire fighting in metal mines under the best of conditions is a dangerous, a slow, and a difficult task. Certain gases generated from combustible material burning in restricted areas are poisonous, even in small quantities, and can not be breathed without serious and often fatal results. In addition to poisonous gases, smoke is given off which obscures the vision of the fire fighter and frequently prevents him from gaining access to the fire area. Many fire-fighting crews have had to turn back because their vision was so impaired by the dense smoke that the fire area could not be located and there was danger of them becoming lost in the mine.In mines having mechanically controlled ventilation - that is, mines not dependent entirely upon natural air currents - the gas and smoke can be forced ahead of the fire-fighting crews, thereby facilitating exploration of the mine and saving the time, energy and oxygen of the mine rescue apparatus crews.Where currents of fresh air can be circulated up to points near the fire without danger of seriously spreading the fire, fresh air bases can be established in the immediate vicinity, and a more intelligent campaign for fighting or controlling the fire can be mapped out.Positive air currents through forced ventilation may also result in saving the lives of miners who otherwise might have been trapped in smoke and poisonous gases.It is generally known that comparatively few metal mines have attempted to regulate or control air currents, with the result that when a fire occurs underground, the normal ventilation may be reversed, short circuited, or the air current may be in one direction one minute and in the opposite direction the next; or, generally speaking, the ventilation can not be depended upon, and smoke and poisonous gases may accumulate in any part of the mine or ""drift"" on the fire-fighters or on the miners endeavoring to escape."

Apr 1, 1921

By John D. Corrick

Three species of chemosynthetic iron- and sulfur-oxidizing autotrophic bacteria have been isolated from the leaching waters of copper mining areas. These species are: The sulfur-oxidizing Thiobacillus concretivorus, the iron-oxidizing Ferrobacillus ferrooxidans, and a sulfur- and iron-oxidizing bacterium closely resembling Thiobacillus ferrooxidans, INTRODUCTION Among several suggested new processes for treating marginal ores in the United States, none is more intriguing than the possibility of extracting metals from low-grade materials by the action of microorganisms One phase of a Federal Bureau of Mines investigation toward developing such a procedure was to isolate and identify specific chemosynthetic iron and sulfur. oxidizing autotrophic bacteria native to certain domestic copper deposits where leaching is practiced. The bacteria or microorganisms considered important to this investigation are those capable of producing solutions of ferric sulfate and sulfuric acid. Solutions of this type are excellent solvents for some copper minerals By establishing the presence of these bacteria at certain copper-leaching areas, strength would be given to a theory that microbial activity is partly responsible for the oxidation that takes place at these areas. Their presence also advances possibilities for controlled use of microbial action in metal extraction processes. Leathen4/ has demonstrated that one of the chemosynthetic iron-oxidizing bacteria, Ferrobacillus ferrooxidans, can oxidize 200 parts per million of ferrous iron to the ferric state in 3 days,

Jan 1, 1961

By C. E. Jordan

Under its program of advancing minerals technology, the Federal Bureau of Mines has invented a laboratory apparatus for continuous separation of minerals based on differences in dielectric properties. The separator consists of a rotating drum electrode and a wire screen electrode positioned 3 mm apart. A high voltage applied across the electrodes that are immersed in a dielectric fluid produces a high-gradient electric field. The high-dielectric-constant (K) minerals are attracted to and conveyed through the separator by the rotating drum electrode, while the low K minerals settle through the screen electrode. Several design and operating parameters, such as electrode configurations, the dielectric liquid and its dielectric constant, electrical voltage and frequencies, feed rates, and particle sizes were studied. In addition, 28 different mineral mixtures were tested with the dielectric separator. In typical tests, a sample of rutile and quartz gangue containing 10-percent rutile was concentrated to 62-percent rutile with 94-percent rutile recovery. A second-stage dielectric separation of the rutile concentrate produced a 92-percent-rutile concentrate. The overall rutile recovery for the two-stage dielectric separation was 86 percent.

Jan 1, 1980

By Sean Gallagher, Thomas G. Bobick, Diane M. Doyle-Coombs, Richard L. Unger

The U.S. Bureau of Mines has developed an in-house facility to evaluate selected effects of whole-body vibration (WBV) levels experienced by underground mobile equipment operators, Vertical vibration data were collected from a coal haulage vehicle via a uniaxial accelerometer attached to the machine frame under the operator&apos;s seat. Data were analyzed and processed so a computer-controlled platform could approximate the vibration signals. Eight men (35.5 yr 2 6.5 SD) participated in a pilot study to evaluate the effects of shock and kBV on heart rate (HR), blood pressure (BP), and subjective discomfort. Subjects were exposed to vibration for 30-min periods while seated in a typical seat (backrest angle at 90° or 130°) &apos;that was plain steel or modified with 2 in foam padding. Subjects repeated the same protocol on a separate day, without the vibration. Results indicated the vibration significantly increased the HR (Q< 0.01), systolic BP, mean BP, the number of times subjects reported discomfort, and overall subjective discomfort rating (pc 0.85). When seated in the steel seat, the overall discomfort rating (E< 0,081) ad the number of times discomfort was reported (p< 0.05) increased significantly. Seatback angle had no significant effect on any of the dependent measures.

By W. R. Reed

Dust dispersion modeling is a subject that has had a large amount of research activity. Much of the research has focused on large-scale global or regional dispersion models. Other models have been created for industry-specific purposes. Furthermore, some of the past research has focused on dust dispersion modeling in the mining industry. This report presents the various dust dispersion models that have been developed specifically for the mining industry. The report first gives a brief background of the regulatory environment that helped to promote development of such models. It then presents an overview of the mathematical concepts used in this dispersion modeling. Finally, each of the various models developed for the mining industry are described, along with their associated mathematical algorithms and any field validation conducted on the different models.

Jan 9, 2005

By John J. McClelland, Gerald T. Homce, John R. Thalimer

The U.S. Bureau of Mines has investigated the early detection of insulation failure in squirrel cage induction motors for the past 4 years. Research was done using a sophisticated empirical data-modeling technique based on values calculated from a motor&apos;s voltage and current phasors. This technique produces two polynomial equations that calculate the insulation leakage current and power. These models were implemented in a prototype system that monitors six motors on a continuous miner for insulation leakage. These insulation leakage values are used to anticipate insulation failure. The system consists of a motor-data-system for each motor on the machine and a control computer located away from the miner. Each motor-data-system consists of an analog interface to the motor&apos;s voltages and currents, a single-board computer that reads digitized data and calculates voltage and current phasors, and a bus node that interfaces the single-board computer with the rest of the system by way of a serial bus system. Using this bus system, the control computer requests and receives phasor data from the motor-data-systems. From these data the control computer calculates and displays two deterioration values for each motor, for leakage current and power, using Bureau-developed models. These values are stored in a data base from which the user can display graphs of each motor&apos;s deterioration values over time.

Jan 1, 1992

By John C. Edwards, Gerald S. Morrow

The U.S. Bureau of Mines has constructed a smoke chamber and developed sensitivity tests for smoke detectors. Response of ionization- and optical-type commercially available smoke detectors have been investigated. Six smoke detectors were measured with respect to visually obscuring smoke characterized by a corresponding optical density for smoldering and flaming coal combustion in the smoke chamber. It was determined that for one type of ionization smoke detector the alarm time was nearly equivalent to that of an odor monitor&apos;s alarm for smoldering coal combustion experiments and earlier for flaming coal combustion experiments. The experiments showed that an average CO concentration of 5 ppm corresponded to an optical density of 0.022 m for smoldering and flaming-1coal combustion. Two of the commercially available ionization-type smoke detectors were more responsive to flaming than smoldering coal combustion at an optical density of 0.022 m, whereas the optical smoke detectors-1showed the opposite trend. The responsive characteristics of the detectors evaluated with respect to known smoke conditions in the smoke chamber shows their potential for use as mine fire sensors or part of a mine atmospheric monitoring system to improve mine safety.

Jan 1, 1995

Develop a full-length-anchored roof bolt that is economical, nontoxic, nonflammable, and non-allergenic. Approach Grout roof bolts with a storable mixture of ultra-fast setting inorganic cement and water. How It Works A loose mixture of dry cement powder, and pinhead-size water droplets encased in waxy globules, are pack-aged in sausage shaped cartridges for storage and use. After the cartridge is inserted Into a drilled hole, the roof bolt is thrust In and rotated to mix the cement and water. The cement hardens in seconds, providing usuable anchoring strengths in minutes. Prior to filling of the sausage shaped cartridges, the microcapsules of water are Intimately mixed with the dry cement. The currently used grouting consists of a mixture of one part water (minimum) with three parts alpha-type gypsum cement and a minor amount of accelerator.

Jan 1, 1978

By Launa G. Mallett, Kathleen Kowalski-Trakofler, Robert H. Peters, Charles PH. D. Vaught, Peter Keating, William J. Wiehagen

On-the-job training is a common means of training or retraining workers and the practice may seem simple and straightforward. Doing it effectively however requires more thought and preparation than simply having someone follow an experienced worker around and watch what they&apos;re doing. Over the years, various techniques and practices have evolved that pass on the skills and knowledge of a trainer or coach in a manner that leads an inexperienced trainee to really absorb the information being taught. On-the-job training thus becomes less a haphazard show-and-tell and more a real transfer of information. The goal of this document is to describe how to develop or manage an on-the-job training program so that information is passed on from trainer/coach to trainee efficiently and effectively. By efficient is meant the best use of time and resources of all those involved in the training process, and by effective is meant that the trainee truly learns the skills and internalizes the knowledge needed to perform the job well. The first part of the document discusses topics to think about when developing a formal on- the-job training program. A structure based on coaching is suggested. Then a workshop designed to prepare trainers as coaches is described. Workshop materials include an instructor’s guide and trainee workbook. These materials can be used to train coaches and to assist trainees as they go through the learning process. Content related to specific jobs can be added to these materials to create targeted on-the job-training manuals. Structuring a formal on-the-job training program It is likely that some form of on-the-job training (OJT) is being conducted at your workplace. The formality of that training can range from a structured program to an informal “follow Joe around” method. If your program is completely unstructured, it may not be meeting current training needs. Worse, it may perpetuate bad habits and create “trained” employees who are not given the same information or evaluated to the same standards. Wiehagen et al. comment that, “Success in using unplanned OJT is usually dependent on the luck of the draw, that is, whether the informal trainer is competent at the task he or she is teaching, is motivated to teach, can organize the job into logical components, and knows something about good practices in teaching and evaluating” (2002, p. 27). It is only through planning a structured OJT program that consistency can be created and maintained. At the least, all trainees who have successfully completed such a program can be expected to perform at an established level—they will know what they must do to be successful.

Jan 7, 2005

By L. J. Prosser, A. T. Iannacchione

From 1991 through 1995, 44 miners out of a total workforce of less than 2,000 were fatally injured in the stone industry. Of these, 12 occurred at underground mining operations with nine deaths resulting from roof or rib falls. A safer environment can be achieved by evaluating the nature of the hazardous ground and by developing more efficient and effective ground-control strategies Roof and rib conditions were observed and assessed in 33 underground stone mines in Illinois, Indiana, Kentucky, Maryland, Missouri, Pennsylvania and West Virginia (Fig. 1). Hazard assessment indicated that the ground failures that occurred under moderate to substantial overburden. i.e., >30 at (100 ft), were caused by stress concentrations and geologic strictures. Ground failures near the surface are caused by solution (water) processes. Selection of the mining horizon and mine-layout decisions tremendously influence ground stability.