Search Documents

By W. E. Wallace, V. Castranova, P. Hathaway, F. H. Y. Green, E. D. Recad, V. Vallyathan, M. J. Keane

Inhaled particle contact with pulmonary surfactant in the hypophase lining pulmonary alveoli was modeled in vitro by exposing two respirable sized dusts, kaolin and silica quartz, to lecithin, a major component of pulmonary surfactant, emulsified in physiologic saline. Lecithin adsorbs to the dusts upon incubation at 37º C and suppresses their cytotoxicity as measured by pulmonary macrophage and erythrocyte assays, suggesting that pulmonary surfactant provides a defense system against prompt cell membrane lysis by inhaled dusts. Subsequent pulmonary macrophage phagocytosis and lysosomal enzyme digestion of the coated dusts was modeled in vitro by incubation with phospholipase A2 for one hour. With increasing lipase activity, silica hemolytic potential was restored to native silica levels. Kaolin was retoxified to levels far in excess of native kaolin hemolytic potential. Elution, thin layer chromatography and phosphate assay of treated dusts indicate most lecithin on silica is digested to lysolecithin and desorbed, silica retoxification being due to surface and adherent lysolecithin effects. Most lecithin on kaolin is not digested in this same time; that which is results in adherent lysolecithin which is responsible for the kaolin retoxification. Digestion with phospholipases A2 and C together produces only weakly retoxified kaolin. Results suggest that surface adsorption properties which control the adherence of prophylactic surfactant distinguish the pathogenic potentials of quartz, kaolin and mixed dust.

Jun 1, 1988

By Charles P. Lazzara, Charles D. Litton, Frank J. Perzak

This U.S. Bureau of Mines report details the results of a series of large-scale experiments where small coal fires were used to ignite the conveyor belt at air velocities ranging from 0.76 to 6.1 m/s. In the tests, electrical strip heaters imbedded within a pile of coal were used to heat the coal to a point of flaming ignition. The flaming coal subsequently ignited the conveyor belt located approximately 5 to 10 cm above the coal pile. During the tests, temperature, CO, and smoke levels were continuously measured in order to determine both alarm time and level as the fire intensity progressed through the stages of smoldering coal, flaming coal, and flaming coal plus flaming belt. Analysis of the data leads to certain conditions of air velocity and sensor alarm levels that are required for early detection of conveyor belt entry fires. Two nomographs are presented, which define sensor alarm levels and sensor spacings as a function of belt entry cross-sectional area and belt entry air velocity.

Jan 1, 1991

By Charles Vaught

This paper discusses the fact that US coal mining organisations are losing the knowledge they need in order to be able to respond to emergencies. The authors note that knowledge management provides a useful perspective from which to view the problem, but that the debate about what constitutes knowledge should be broadened to include a debate about what constitutes management. It is argued here that knowledge is actually shared knowing distributed across group members; that such knowledge can be managed by cultivating it; and that narrative is the medium through which this may be done. The paper then examines NIOSH research that has attempted to use such an alternative knowledge management approach to help potential mine emergency responders better deal with the predicaments they are likely to encounter on-site.

Jan 1, 2006

By G. B. Atkinson

To develop technology to help assure an ample domestic supply of zinc, the Bureau of Mines is investigating an aqueous chlorine-oxygen leaching process for treating complex sulfide concentrates. This report discusses the purification of aqueous C12-02 leaching solutions by utilizing zinc cementation to remove Cd, Co, Cu, Ni, and Pb. Additional processing of the purified solution is necessary to produce ZnC12 crystals suitable for molten-salt zinc electrowinning cells. The effects of solution temperature, reaction time, zinc dust concentration, ZnCl2 concentration, and degree of agitation on the removal of impurities were investigated for both simulated and actual leaching solutions. Zinc dust addition to a leaching solution at 30° C decreased the Cd, Cu, Ni, and Pb concentrations to acceptable levels of less than 3 mg/1 each. By increasing the solution temperature to 75° C, the cobalt content was decreased to less than 5 mg/l, an acceptable level for producing electrolytic cell-grade ZnC12. Impurity removal rates from ZnCl2 solutions are Pb>Cu=Cd>Ni>>Co. An increase in the solution temperature increases the rate of removal for these metal impurities.

Jan 1, 1982

By L. B. Pankratz

The Bureau of Mines determined low-and high-temperature thermodynamic properties for anhydrous ferric sulfate and anhydrous indium sulfate. Low-temperature heat capacities were measured between 50° and 298° K, and enthalpy increments above 298° K were determined. The high-temperature measurements of Fe2(S04)3 extended to 900° K and those of In2(S04)3 to about 1,000° K. A minor transition was found for Fe2(S04)3 at 800° K, with a heat of transition of 540 cal/mole. Tabulations were made of the low-temperature heat capacities and the high-temperature enthalpy and entropy increments. The 298° K entropies derived from the low-temperature measurements were 67.6±0.S ca1/deg mole for ferric sulfate and 72.2±O.5 cal/deg mole for indium sulfate. High-temperature enthalpy increments were also given in equation form.

Jan 1, 1969

By Kenneth H. Johnston

Information and data necessary for research on improving methods of oil recovery from low-permeability reservoirs and for comparison and evaluation of performance of such reservoirs with those producing from more permeable sands were obtained. Core analyses, well logs, production tests, well stimulation techniques, primary and secondary production records, and data on two water-flood projects were examined for wells producing from the Bartlesville sand, West Avant field, Osage County, Okla. Overall recovery from the study area was generally poor with only 9.0 percent of the pore volume recovered to January 1, 1968. Larger fracture treatments (8,000 to 12,000 gal) could have resulted in an increase in primary oil recovery. Secondary recovery by water-flooding accounted for only 1.9 percent of the pore volume because of the inability to control the large volume of injection fluid that escaped from the flood patterns and the excessive volumes of water produced with the oil. Future waterflood development in other low-permeability reservoirs should include the drilling of new input wells, use of injectivity surveys to locate possible natural fracture systems, or zones of high permeability, and control of injection fluids by altering flood patterns and/or plugging of the more permeable zones.

Jan 1, 1968

By Timothy J. Orr, Michael J. Beus, Frank T. Duda

The technology to enhance safety and control features for mine shaft hoists is being investigated by researchers at the U.S. Bureau of Mines (USBM). The objective of the research is to prevent injuries and fatalities related to hoist and elevator operations. Monitoring and controlling mine hoisting operations will allow hoist operators, inspectors, and maintenance personnel to increase their awareness of potentially dangerous situations and provide controls for safer operations. Process simulation and visualization software, real-time data sensing, and advanced programming techniques are being applied to this problem. Development of reliable and cost-effective sensors and data acquisition interfaces to monitor hoist loads and detect slack rope conditions is underway. Three-dimensional design software was used to visualize mine hoisting to enhance understanding of hoist operations. Quick Basic and Visual Basic (an object-oriented Windows interface) are being used for acquiring and processing hoisting data. Testing and evaluation of components are underway at USBM testing facilities. The resulting system will allow hoist personnel to assess critical operating parameters, such as hoist position, speed, acceleration, conveyance load, and rope tension.

By Fred C. Turin, Sean Gallagher, Kim M. Cornelius, William J. Wiehagen

An important part of initiating a site-wide ergonomics evaluation process is prioritizing jobs to be analyzed. While injury data is important, other factors such as worker discomfort and physical exertion requirements, should be considered. This paper describes the use of four sources of data (injury records, the Nordic Standardized Musculoskeletal Questionnaire, supervisor interviews, and management concerns) to prioritize jobs for ergonomic analysis. The approach described integrates the four sources using a decision matrix to prioritize jobs for ergonomics analysis.

By E. J. Gleim

The construction of explosion-proof electric mine equipment for operation in gassy coal mines of the United States was begun as early as 1903. In 1.906, similar equipment with special protective devices was built for export. An investigation of explosion-proof motors was conducted by the United States Bureau of Mines during 1910 and 1911. In other words, this was among the first efforts of the Bureau directed toward the saving of life and property subsequent to its establishment by act of Congress in 1910. In these early motors, those with special devices for relief of explosion pressures predominated. At that time it was generally considered that, by providing for pressure relief, the enclosures could be made lighter in weight because of the lower explosion pressures developed within.

Jan 1, 1954

To inexpensively monitor the ventilating airflow anywhere in underground working places. The Approach: The Bureau has developed a small self-contained monitor which sounds an audible alarm and energizes a flashing lamp if air velocity decreases below normal. How It Works: The sensing element of this inexpensive monitor is a thermistor, which is self-heated by a constant-current electrical source. Airflow over the thermistor increases heat removal and lowers the thermistor temperature. Since the electrical resistance of a thermistor is a function of temperature change, the voltage across it varies with temperature, and, therefore, the air velocity. Changes in the voltage across the thermistor are amplified, and can be used to trigger the alarms.

Jan 1, 1975

Improve mine refrigeration system efficiency while providing free electrical energy to mines. Approach Convert the potential energy of incoming mine water falling down long vertical shafts into electrical energy by means of a turbine-generator system located at the bottom of the mine shaft. How it Works Converting the energy of falling water into useful work is a well-developed engineering concept. Water flowing down long vertical pipelines into deep mines develops high pressure that can be used to operate a turbine-generator system at the bottom of the pipeline. A thermal energy recovery system of this type offers three advantages: 1. In systems without turbines, the potential energy of the water is converted to heat. The water temper-ture will automatically

Jan 1, 1985

By L. R. Burdick

The Smokescope is an instrument recently developed for determining the density of smoke by shade comparison. The instrument is designed so that the smoke is seen adjacent to two shades of gray corresponding to Nos. 2 and 3 on the Ringelmann chart. Data on smoke density are important in the smoke-abatement field. The method that is specified and accepted as standard for smoke-density determination by the majority of city smoke regulations involves comparing the smoke shade with the four shades on the Ringelmann chart as published by the Bureau of Mines.2/ This investigation was made to determine the accuracy and convenience of the Smokescope. It was conducted as a part of the Bureau I s air-pollution work, which includes the study of techniques that will promote smoke abatement. The accuracy of the Smokescope was arbitrarily defined as the difference between the Smokescope determinations and the determinations by the accepted, standard method and was expressed as Smokescope correction. Although the corrections obtained were strictly correct only for the two observers and the Smokescope of the investigation, they indicate what might be expected from any observer who uses a Smokescope with reference shades that duplicate those of the test instrument. The report is devoted largely to the data on Smokescope correction, which were taken from a single stack under controlled smoke conditions. Field work, which was done at various locations with different stacks, is mentioned briefly in connection with the comparison of the convenience of the two methods. The data for estimating Smokescope correction were taken for the three variables that were expected to affect the results, namely, the density of the smoke, the amount of light, and the color of the sky behind the smoke.

Jan 1, 1955

By John J. Sammarco, Janet S. Flynt

This report (Independent Functional Safety Assessment Guidance 7.0) is the last in a nine-part series of recommendations and guidance addressing the functional safety of processor-controlled mining equipment. It is part of a risk-based system safety process encompassing hardware, software, humans, and the operating environment for the equipment’s life cycle. Figure1 shows a safety framework containing these recommendations. The reports in this series address the various life cycle stages of inception, design, approval and certification, commissioning, operation, maintenance, and decommissioning. These recommendations were developed as a joint project between the National Institute for Occupational Safety and Health and the Mine Safety and Health Administration. They are intended for use by mining companies, original equipment manufacturers, and after-market suppliers to these mining companies. Users of these reports are expected to consider the set in total during the design cycle. • 1.0 Safety Introduction (Part 1).—This is an introductory report for the general mining industry. It provides basic system/software safety concepts, discusses the need for mining to address the functional safety of programmable electronics (PE), and includes the benefits of implementing a system/software safety program. • 2.1 System Safety (Part 2) and 2.2 Software Safety (Part 3).—These reports draw heavily from International Electrotechnical Commission (IEC) standard IEC 61508 [IEC 1998a,b,c,d,e,f,g]and other standards. The scope is “surface and underground safety-related mining systems employing embedded, networked, and nonnetworked programmable electronics.” System safety seeks to design safety into all phases of the entire system. Software is a subsystem; thus, software safety is a part of the system’s safety. • 3.0 Safety File (Part 4).—This report contains the documentation that demonstrates the level of safety built into the system and identifies limitations for the system’s use and operation. In essence, it is a “proof of safety” that the system and its operation meet the appropriate level of safety for the intended application. It starts from the beginning of the design, is maintained during the full life cycle of the system, and provides administrative support for the safety program of the full system. • 4.0 Safety Assessment (Part 5).—The independent assessment of the safety file is addressed. It establishes consistent methods to determine the completeness and suitability of safety evidence and justifications. This assessment could be conducted by an independent third party. • Safety Framework Guidance.—It is intended to supplement the safety framework reports with guidance providing users with additional information. The purpose is to assist users in applying the concepts presented. In other words, the safety framework is what needs to be done and the guidance is how it can be done. The guidance information reinforces the concepts, describes various methodologies that can be used, and gives examples and references. It also gives information on the benefits and drawbacks of various methodologies. The guidance reports are not intended to promote a single methodology or to be an exhaustive treatment of the subject material. They provide information and references so that the user can more intelligently choose and implement the appropriate methodologies given the user’s application and capabilities. The guidance reports comprise parts 6 through 9 of the series and are listed below: [< 5.1 System Safety Guidance (Part 6).—This guidance supplements 2.1 System Safety. < 5.2 Software Safety Guidance (Part 7).—This guidance supplements 2.2 Software Safety. < 6.0 Safety File Guidance (Part 8).—This guidance supplements 3.0 Safety File. < 7.0 Independent Functional Safety Assessment Guidance (Part 9).—This guidance supplements 4.0 Independent Functional Safety Assessment.] [ ]

Jan 4, 2006

By J. G. Croeni

The titanium-iridium alloy system was investigated to determine whether alloys of this system would merit further development as control-rod material for nuclear reactors. A study was made to determine the titanium-iridium phase diagram by using melting-point, thermal analyses, X-ray diffraction, dilatometric, electrical resistivity, and metallographic techniques. The titanium-iridium alloy system was investigated between 500° and 2,400° C. Results indicate the formation of two intermetallic compounds, Ti3Ir rind TiIr3, and one intermediate solid solution centered about the 50 atomic percent iridium composition. A eutectic reaction occurs at 1,475° C, and 19 atomic percent iridium. The Ti3Ir decomposes peritectically at 1,520° C. The intermediate solid solution exhibits a maxima of 2,140° C. at 50 atomic percent iridium. This phase is also believed to undergo an order-disorder transformation at 1,750° C. Another eutectic reaction takes place at 2,000" C. and 60 atomic percent iridium. The compound TiIr3 formed at 75 atomic percent iridium decomposes peritectically at 2,115° C. Further increases in iridium content result in the formation of an iridium-rich terminal solid solution. Information obtained below 900° C. in titanium-rich alloys indicates that iridium acts as a beta stabilizer in titanium, and the authors believe that a eutectoid decomposition of beta-titanium occurs near 500° C. and 10 atomic percent iridium.

Jan 1, 1962

By W. L. Staker

The Bureau of Mines investigated methods for selectively eluting mercury, silver, and gold from strong-base anion-exchange resins, including Rohm and Haas resins lRA-430 and 900 and Dow Chemical resins 2lK, SMA-I, and SBR. Resins were typically loaded to 145 oz/st of each metal. Loaded resins were eluted with H2S04, NaCl-H Cl, NaOCl, and NaCl04 solutions. The resins tested had similar elution characteristics for mercury and precious metals. The best selective elution scheme was achieved by eluting in a column with 2N H2S04 to recover 99 to 100 pct Hg, with 200 giL NaCl in IN HCI to rec;ver 99 to 100 pct Ag, and with 2M NaCl04 to recover 79 to 89 pct Au.

Jan 1, 1987

By Ann G. Kim

Samples of gas were obtained directly from the coalbed during drilling of horizontal and vertical boreholes in six different formations. The samples were analyzed by gas chromatography for C1 to C5 hydrocarbons and for O2, N2, H2, He, and Co2. Methane in the gas varied from 63 to 99 percent; carbon dioxide from 0.1 to 15 percent. The CH4/CO2 ratio varied and showed no apparent correlation with age, rank, or bed. The majority of samples contained ethane, propane, and butane; hydrogen and helium were found in some samples. Oxygen and nitrogen were usually present, possibly as a result of air contamination. A more extensive sampling program would be necessary to establish relationship between the amount and composition of the gas in the coalbed and other factors.

Jan 1, 1973

By Alice V. Peter

Meerschaum or sepiolite is employed principally in tobacco pipes and cigar and cigarette holders, although a few other uses of minor importance are Down. The unique value of a meerschaum pipe is derived from the owner&apos;s pleasure in watching the color deepen with smoking and in having the color "set" at the desired shade. The name "meerschaum" (German for "sea foam") is applied because the material, when pure and dry, will float on water. Owing to its resemblance to the porous, bonelike structure of the cuttlefish, or septa, it is also known as sepiolite. There are a few scattered deposits of meerschaum in. the United States which have yielded a small product ion, but the world&apos;s supply of the&apos; material is obtained fined principally from Asia Minor, Meerschaum deposits near Eski-Shehir, Turkey, are said to have been worked 2,000 years ago, but commercial exploitation is a development of the last hundred years DESCRIPTION AND PROPERTIES Meerschaum is a hydrous magnesium silicate (H4Mg2Si3010) having the following theoretical analysis: Si02, 60.8 percent; MgO, 27.1 percent; H20, 12.1 percent. It is a soft. (H.2 - 2.5), fine-grained, earthy, white, gray, or yellow material. It is very light weight when pure (specific gravity, 1 to 2) and is highly absorbent. Because of its porosity the proportion of water present in the mineral is affected by the humidity&apos;of the atmosphere. In a moist atmosphere the water content may be as much as 21.7 percent. Then wet the material is soft and somewhat plastic. When dried again it becomes lard and tough. The toughness is especially apparent in some forms that have a fibrous or leathery texture.

Jan 1, 1934

By L. H. Adami

Heats of formation were obtained for four anhydrous crystalline sodium borates by hydrochloric acid solution calorimetry. The heats of formation at 298.15° K from the elements are NAB02, -233.2 ±0.6 kcal/mole; Na2B07, -786.4 ±1.0 kcal/mole; NaB305, -549.9 ±0.8 kcal/mole; and Na2B6013, -1,412.5 ±2.0 kcal/mole, The heats of formation from the constituent oxides are NaB02, -31.5 ±0.8 kcal/mole; Na2B407, -78.8 ±1.3 kcal/mole; NaB305, -44.1 ±0.8 kcal/mole; and Na2B8013, -96.7 ±1.5 kcal/mole.

Jan 1, 1968

By C. E. Saxon, F. E. Cash

"Adequate lighting for all mining operations would unquestionably tend to promote both safety and efficiency; this would be true not only for men but also for the animals that man impresses into service in mines. The Markeeta Coal Co. and the Alabama Fuel & Iron Co. both operating mines in Alabama, have found that equipping mine mules with portable electric lights is more efficient, much more humane, and far more safe for both men and animals then the more or less usual method of forcing the animal to do its work essentially in darkness.This report is intended to give the mining industry data, that will aid in trying to bring about safe and efficient operation of mines.The authors desire to thank Charles F. DeBardeleben, president, Fred R. Bell, general manager, Hewett Smith, C. H. Shepherd, and R. A. Sensing, superintendents for the Alabama Fuel & Iron Co.; and Charles F. DeBardeleben, Jr., president, and H. M. House, superintendent for the Markeeta Coal Co., for their cooperation in furnishing the data for this paper.The eight mines operated by the Alabama Fuel & Iron Co. and one operated by the Markeeta Coal Co. in Jefferson and St. Clair Counties, Ala., are the only mines in Alabama where mules are provided with portable electric lights, and there are few if any mines in other States in which this system is in use.These two companies are convinced that equipping all mine mules with good lights decreases underground haulage cost by animals by prolonging the useful life of the animals, increasing their efficiency, lessening haulage wrecks and delays on haulage, and increasing production. Last but not least of the advantages would be the more humane treatment of the animals.The nine mines are developed by slopes along the dip of the coal bed, with double-room entries on 200- to 300-foot centers turned right and left off the slopes and with approximately 1 per cent grade in favor of the loads. Rooms are driven up or diagonally up the pitch from these entries.A surface hoist delivers the empties from the surface to the entry sidetracks at the slope and pulls the loads to the surface. From these sidetracks, mules pull one to four wooden cars, each of which holds 1-1/2 to 2-1/2 tons of coal, deliver the empties to the rooms and entry faces, and pull the loads to the slope sidetracks. The mule haul varies from 100 to 3,000 feet; there are no locomotives or trolley wires in any of these nine mines, seven of which are rated as gassy and two as nongassy by the Alabama state Mining Department."

May 1, 1933

By T. O. Llewellyn

The Bureau of Mines conducted laboratory batch beneficiation tests on a waste granite sludge from New Hampshire to determine the feasibility of recovering a reusable silicon carbide product. The granite sludge responded to attrition scrubbing, desliming, and flotation in either alkaline or acid circuits using fatty acid as a collector. Recovery of over 80 percent of the contained silicon carbide at grades of up to 96 percent SiC was obtained.

Jan 1, 1975