Search Documents

By Michael J. Friedel

As part of an investigation aimed at improving the health and safety and competitiveness of the mining industry, the U.S. Bureau of Mines evaluated the application of common offset radar profiling, using a 250-MHz ground-penetrating radar (GPR) system, for the detection of fractures in igneous rock. A series of radar reflection surveys were conducted to detect and delineate the extent of fracturing at various granodiorite and gabbro quarries and outcrops located in Minnesota. The application of radar profiling for detecting joints, sheeting fractures, shear zones, and depth to water table was demonstrated to be feasible with minimal processing. Radar reflection interpretations were verified by visual inspection of the rock mass and field mapping of local structure. The radar reflection section provides a simple, rapid, and cost-effective means for mapping of shallow (less than 10 m) small-scale fractures (greater than 0.25 cm) in igneous rock masses (characteristic of velocities between 0.061 m/ns for gabbro and 0.125 m/ns for granodiorite). Depth or distance estimates to fractures are within 10 pct of the actual, and time-shift compensation is necessary only when topographic irregularities exceed 30 cm.

Jan 1, 2010

By C. W. Owings

Recent recommendations of the Bureau of Mines regarding, rock dusting to prevent dust explosions in coal mines have been issued as Mine Safety Board Decision 32 and printed as Information Circular 7109.5/ The last paragraph on page 2 of I. C. 7109 states: After a mine or any part of a mine has been rock-dusted, samples of dust for analysis should be taken from the floor, ribs, roof, and timbers at such intervals of time as will give apple warning of need far redusting in order to maintain the required minimum percentage of incombustible in the mine dust. Details of the methods of sampling and analysis are given in Bureau of Mines Information Circular 7113.

Jan 1, 1940

By C. L. Brown

The frequency of mine fires during recent years, with an apparent increase in recent months, has focused attention on the necessity of reducing this hazard by every means possible. Investigation reports are available on 51 mine fires of electrical origin between August 15, 1949, and August 16, 1954. Nine other fires in the same period were suspected as being of electrical origin. Every mine fire is a potential hazard to underground workmen; it is remarkable that only six lives were lost as a result of these fires, since the injury list was very high. Modern mining methods, with increased power demands and extended distribution systems underground, involve greater electrical hazards and possibilities of costly production delays as a result of inadequate electrical service. Improvements in electric-power-distribution facilities in many underground coal mines is desirable. The purpose of this paper is to show the need for this improvement as revealed by studies and investigations of electric-power-distribution systems representative of those in a large number of coal mines.

Jan 1, 1955

By McHenry Mosier

Diamond -drilling blast holes at Eastern Magnetite Mine C is proving economical in boundary shrinks , in removing pillars not readily accessible for percussion drilling , and in driving scraper drifts . The cost per foot drilled is greater than for percussion drilling , but savings in associated factors outweigh this handicap . The rocks drilled include trap rock and magnetite ore . The mining method is the panel , block- caving system utilizing scraper sublevel drifts instead of branch raises to convey the ore to the haulage level . Diamond -drilling blast holes was begun early in 1945. Three rigs equipped with noncoring bits are now in active operation two shifts per day . They are owned by the company , and the drill operators are paid by the day . In shrinkage stopes the drill is mounted on a horizontal bar set against opposite walls of the stope . Stoping holes are horizontal , which gives better results in blasting and requires fewer set ups . In scraper drifts the drill is mounted on a horizontal bar clamped to two columns about feet apart . Trim holes around the periphery of the drift and reliever holes are drilled 50 to 80 feet in length . A 10 - foot wedge cut drilled with a stoper is blasted in conjunction with a corresponding length of the trim holes to effect a 10 -foot advance of the full- sized drift . Recent drilling averages 97 feet per machine shift , excluding time utilized in setting up and moving the machine , hand mucking , and barring down . The feet drilled per bit at present is 417. These data represent the average for drilling in both rock (waste) and ore . Percussion drilling utilizes three types of wet drills . Detachable bits are standard . Gage changes for new bits is 1/8 inch and for reconditioned bits 1/16 inch . The life of a bit is five uses . Resharpening is on contract . A drill carriage is used in haulage headings .

Feb 1, 1948

By M. C. Simmons, Boyd Gutorie

Desulfurization experiments at the Petroleum Experiment Station of the Bureau of Mines at Bartlesville on virgin light distillates obtained from some ‘high-sulfur’ crude oils have shown that the octane numbers of the original distillates are increased on the average about one unit, that the octane numbers of distillates with 4 ml. tetraethyl lead are increased 2 to 3 units, and that the The Petroleum Experiment Station, at the request of the Petroleum Administration for War, instigated and has in progress an investigation of crude oils of the United States to determine their possibilities for yielding straight-run distillates suitable for use as base or blending stocks to produce high octane aviation gasoline. One phase of this investigation deals primarily with so-called ‘high-sulfur’ or ‘sour’ crude oils by seeking to determine the effects of sulfur removal upon the virgin distillates prepared from these crude oils. To date, virgin distillates from several ‘high-sulfur’ crude oils from Texas, New Mexico, and Oklahoma have been prepared and desulfurized in pilot-plant distillation and desulfurization units at the Petroleum Experiment Station. The properties of the undesulfurized and desulfurized distillates were determined and compared to show the effect of sulfur removal. Results of these investigations showing the suitability of these crude oils as sources of virgin naphtha aviation base stocks have been prepared and forwarded to the Petroleum Administration for War and other approved persons. The following preliminary summary is presented to acquaint those interested not only with the present results of the investigation of several ‘high-sulfur’ Texas, New Mexico, and Oklahoma crude oils, but also to give some basic information as to certain sulfur compounds, especially their identification in straight-run distillates, their depressing effects upon the octane numbers of leaded fuels, the benefits obtained by their partial and complete removal, and some of the processes being used to effect their removal.

Nov 1, 1943

By Oliver Bowles

"The manufacture of asbestos paper began commercially about 40 years age but its principal development has taken place during the past twenty-five years. The asbestos used by the ancients, termed amiantus by Pliny was used for winding sheets, tablecloths and other fabrics. It was probably chrysotile fiber and was a woven and not a felted product, and there¬fore is not to be confused with asbestos paper. There are, however, some early references to paper manufacture that are of interest. Pontoppidian, Bishop of Bergen, in his Natural History of Norway, published in 1750, refers to paper made from asbestos found in the parish of Waldens. He states that this paper did not burn when thrown in the fire, but the writing on it totally disappeared. This indicates that the primary ob¬ject was to obtain an indestructible writing paper. About 100 years later, further efforts were made with the same object in view. In 1853, a patent was issued for a process of making paper from a mixture of asbestos and alum. Many experiments were made to manufacture suitable asbestos printing paper. Some such papers contained only about one-third asbestos, the remainder being of combustible material. Such papers would burn, but would leave a white residue which retained its shape and preserved the written characters. On account of the difficulty of obtaining a smooth and even surface, and the tendency for the material to absorb ink like blotting paper, asbestos paper is not well adapted for writing or printing purposes. Other early uses of asbestos paper were for ornamental wall-paper and carpet linings. None of the uses mentioned above have developed to anything of importance in a practical way, but the manufacture of asbestos paper has become a very important industry, and it has found extensive uses in ways that were never dreamed of by the early investigators.It is recorded that the first sheet of asbestos paper made in America was manufactured in 1876 by John Roberts & Son Company, in a mill near Waltham, Mass. The material first used was a long-fibered amphibole asbestos from Italy. About three years later, Canadian fiber was introduced and proved to be very satisfactory. The shorter grades of fiber which would otherwise be wasted were used for the manufacture of paper and board. For several years, the product of this mill was sold through Rice Kendall of Boston, Mass. From 1881 to 1900, the H. W. Johns Company, of New York, took the entire product which was 30C to 700 tons per year. The latter company built their own asbestos paper mill at Brooklyn in 1900. Keasbey & Mattison Company, of Ambler, Pennsylvania, began to manufacture in 1897. Other early manufacturers were: the Asbestos Paper Company, at Baldwinsville, Mass„ and Mr. B. S. Binney, at Shirley, Mass. The number of manufacturers gradually increased until at present asbestos paper is manufactured by the following ten companies:"

Nov 1, 1919

By John R. Reeves

The development of an new industry, which must prepare its marketable products at or near the source of the raw material, and ship them to a market which may cover half a nation, is more or less influenced by a number of natural and cultural conditions such as (1) location of plants with respect to a large market, (2) climatic conditions, (3) transportation facilities, (4) labor supply, and (5) water supply. An effort is made in this pager to give in detail a number of the more important of these conditions as they affect, either favorably or unfavorably, the development of the oil-shale resources of southeastern Indiana. The utilization of the New Albany formation for the production of oil will be similar to a large scale low-grade ore proposition in which the raw material can be obtained in very large quantities at a relatively low cost. It appears, therefore, in considering the value of this shale or its economic position in relation to other oil shales, tie cost of mining and preparation for the retort are of prime importance.

Jan 1, 1923

By H. R. Batchelder

Much information on oxygen production and the manufacture of synthetic liquid fuels has been published during the past several years. From time to tine the investment and operating cost of oxygen plants of various sizes has been estimated. Surveys have been made so that the various processes by which oxygen is produced commercially might be compared. The gas-making processes in which oxygen is employed, which wore used in Germany during the war, have been described in T.O.M. reels, and this information has been published. Descriptions of pilot-scale or proposed commercial plants for the production of synthesis gas or hydrogen and their conversion to synthetic liquid fuels also have been published. In general, each of these publications has dealt with a particular phase of the over-all problem. The present paper will discuss the relationship between these phases: The factors that affect oxygen manufacture and costs, the methods for the use of oxygen and for the production of synthetic liquid fuels, and, to some extent, the economic factors that must be considered.

Jan 1, 1951

By F. Garcia, J. Cervik

Recent advances in the commercial separation of gases using membranes have renewed interest in the possibility of applying this technology to the recovery of methane ( CH4 ) from mining operations . This Bureau of Mines report briefly reviews the history of the development of membranes for gas separation , the theory of how they work , and their application to the separation of methane from air and associated problems . However , methane -air mixtures are difficult to separate with membranes because the pertinent gas couples , 02 - N2 , 02 - CH4 , and N2 -CH4 , have poor separation characteristics , as indicated by their separation factors of about 3 or less . Even if these separation factors were substantially higher , there is doubt that methane could be recovered economically from the low concentrations in mine ventilation exhaust ( 2 vol pct or less ) . The exhaust pressures are not sufficient for adequate separation . The power cost of compressing the methane recovered . these mixtures would far exceed the value of New discoveries could make separation of gob hole methane - air mixtures practical . These mixtures have much higher concentrations of methane (from 30 to 100 vol pct ) ; however , for safety reasons , be limited to gob gas with 60 vol pct CH4 or more .

Jan 1, 1988

By L. C. IlsLey

Permissible blasting units are approved with the understanding that if actively marketed they will be listed as permissible so that all interested in such safety equipment may know what is available. The last detailed lint of permissible units was published as Technical Paper 4294/. All of the blasting units of that list have become obsolete or have boon modified as covered by extensions of the original approvals.

Jan 1, 1941

By Oliver Bowles

Granites are classed as igneous rocks ; they have been formed by the solidification of rock magmas or solutions from deep within the earth . It is an almost invariable law of nature that magmas which cool quickly form fine- grained or glassy rocks , while those that cool slowly are completely crystallized and are coarser- grained . Granites , being of the latter class , are regarded as having attained their solid form at considerable depth below the surface under conditions of high temperature and pressure . The constituent minerals crystallized out slowly , the crystals interlocking with one another . The great depth of overlying rocks that must have been present when crystallization took place has been removed by erosion over large areas on the surface of the earth , in consequence of which granites appear at or near the surface in many localities . The chief minerals of which granites are formed are feldspars , quartz , and either mica or hornblende . All the essential constituents except mica are as hard as , or harder than steel , therefore granites are difficult rocks to cut and dress . Granites are usually red , pink , or gray , depending on the color of the feldspars . If hornblende or black mica is abundant the rock may be dark green or almost black . Granites are characterized by massive homogeneous texture . They are classified as fine- grained , medium- grained , or coarse - grained . Medium- grained granites are those in which the feldspar crystals average about one- fourth inch in diameter . If relatively coarsegrained crystals appear in a fine -grained ground mass the rock is designated a porphyritic granite . Uniformity in texture and grain size are desirable in building and ornamental stone , although occasionally rocks of variable texture , such as the porphyritic granites , are used . A rock may have the mineral constituents of a granite but show a banded or platy structure due to recrystallization , folding , or other changes while the rock was in a plastic or semimolten condition . Such metamorphic rocks are called granite gneisses . They are used occasionally for building purposes but not as commonly as the uniformly textured granites . - Granites are named from the most abundant mineral other than quartz and feldspar that they contain , being called , for example , biotite granite or hornblende granite . - Commercially other igneous rocks granitoid in texture but more properly classified as syenites , diorites , or gabbros may be classed as granites . Thus the " black granite " of Little Falls , Minn . , is a diorite , and the " black granite " of Eastern Pennsylvania consists of diabase or gabbro . The question is sometimes raised as to the depth to which a granite occurrence may extend . In this respect granites differ notably from limestones , sandstones , or other sedimentary rocks . The sediments were originally laid down in relatively thin beds , and individual formations providing rock of economic value may be quite limited in thickness . Usually the usable beds range between 40 and 200 feet in thickness . On the other hand , granite comes up from below . Its depth is unknown , but in general is very great . It may even be measurable in miles . The reserves of material at depth are to be measured , therefore , by the economic depth of working rather than by the vertical extent of the rock mass . Exceptionally , granites of commercial quality may occur in sills or sheets of limited thickness flanked on either side by rocks of different character , as , for example , at Westerly , R. I.

May 1, 1930

By G. S. Rice

[This paper describes preliminary tests at the Bureau's Experimental Mine to determine, under conditions that may prevail ira bituminous coal-mine heading, how small a quantity of fire damp may bring coal-dust into suspension and ignite to it. The results show that the explosion of as little as 150 cubic feet of an explosive mixture of gas and air containing 9 per cent natural gas may start a disastrous explosion Of coal-dust. This is a very small volume, of gas, to cause such a result. Let us suppose that this amount of exclusive mixture, was at the face of an entry which was 10 feet wide and the face was overcut to a depth of 6 foot and an upper layer of coal 2 1/2 feet thick had been removed, the recess so made would save a volume of 150 cubic feet. Furthermore, only 13 cubic feet of pure methane is needed in this volume to produce this 9 per cent explosive mixture.]

Jan 1, 1930

By Suresh K. Bhatt, Dennis R. Dolinar

The roof bolt system of a mine, if properly selected and installed, can allow for better roof control and reduce the potential for roof falls. Because of this potential to reduce roof falls and improve ground control conditions, the National Institute for Occupational Safety and Health (NIOSH) has an interest in the types of roof bolts that are used by the coal industry. Further, NIOSH has conducted research into how various support parameters can affect the number of roof falls that occur, including support type. Today, the five main types of roof bolts installed in U.S. coal mines are mechanical anchor bolts, point-anchor or resin-assisted mechanical anchor bolts, torque-tension bolts, combination bolts, and fully grouted resin rebar. This paper describes each support in detail. Because of the importance of resin in the functioning of the majority of bolts installed, resin grouts are also discussed. Further, trends in the types of roof bolts used are reviewed. Over the last 10 years, the significant trend has been the large reduction in the relative number of mechanical anchor bolts that are installed. These bolts have been replaced mainly by the resin-grouted rebar system. Data are also presented to show the impact of these changes in bolting on the number of roof falls.

Jan 10, 2000

By R. W. Smith, S. H. Ash

Marked progress in safety has characterized the operation of coal mines in general in the State of Washington during the 5- year period 1928-1932 , particularly during the years 1931 and 1932. Physical conditions such as steep pitches , inherently bad roof and floor , prevalence of gas , and explosibility of the dust of Washington coals present certain definite hazards . Although advances have been made in accident reduction in Washington , the State still has far to go in that direction . The State has endeavored to reduce its coal -mine accidents by the usual method of making certain definite safety requirements mandatory . The value of education has not been underrated , but the educational method used has not altogether achieved the res lts desired by the industry itself , particularly within certain imdividual organizations . The past 2 years have witnessed a growth , in certain instances , of the essential ideas that the observance of safety precautions on the part of all is demanded if accidents are to be reduced , and that the initiating and carrying out of any program to promote and obtain desired results in accident elimination must begin and function from the top downward . Mining operations of Washington mines have been described in various publications of the United States Bureau of Mines .

Jun 1, 1933

By Hylton R. Brown

Although extensive research has been carried on to determine the factors affecting the explosibility of carbonaceous dusts, as much has been published on coal-dust and grain-dust explosions recent reports of loss of life and property in explosions if metal dusts emphasize the lack of information on the extent of the dust-explosion hazard in plants manufacturing or handling; aluminum, magnesium, or zinc powder, as well as other metal or mineral dusts. Early investigators believed that only the carbonaceous dusts formed explosive mixtures with air, and it was not until near the beginning of the present century that the explosibility of certain metal and mineral dusts was recognized generally. In his book, entitled "Fire and Explosion Risks," published in 1904, Von Schwartz called attention to such hazards. Many vague references to metallic-dust explosions are found in the literature, such as "a severe explosion of aluminum dust occurred in the Middle West several years ago," but very little information seems to be available on the extent of the hazard, the number of explosions, or the amount of loss caused by explosions in pants handling metallic or mineral dusts or powders other than those of a carbonaceous nature. A search of the records of insurance companies, rating bureaus, fire underwriters,and fire-protection associations as well as the files and records of Government agencies has been made to obtain authentic data on explosion losses. To indicate the extent of the hazard a summary of laboratory tests covering the explosibility of certain metal dusts, with brief reference to their uses and Methods of manufacture, and the data compiled from the information available on losses are presented in this publication.

Jan 1, 1941

By R. L. Handy

The goal of this research was to adapt the highly successful rock borehole shear test for use in deep, small-diameter boreholes. Operating somewhat on the principle of a rock bolt, the borehole shear test measures both the expansion pressure and pulling force to give discrete measures of rock shearing strength as a function of the applied normal pressure. A new instrument was designed and built to fit into a 2-3/8 inch diameter hole. Unfortunately the design became so complicated, the operation is nut reliable. This is attributed to constraints of the small hole, and added requirements of an in-hole anchor to push against, and a rotating shear plate cleaner for repeated tests down-hole. A clue to the d: vice complexity is its length, which is over 10 feet. Furthermore it employs concentric cylinders and one hydraulic cylinder bored into the piston of another, or it would be even longer. Meanwhile drilling technology has advanced to greatly reduce costs of drilling 5- or 6-inch diameter holes. The downhole tester therefore should be redesigned and simplified for use in a larger diameter drill hole.

Jan 1, 1982

By G. S. Rice

This paper describes preliminary tests at the Bureau's Experimental Mine to determine, under conditions that may prevail in a bituminous coal-mine heading, how small a quantity of fire damp may bring coal-dust into suspension and ignite it. The results show that the explosion of as little as 150 cubic feet of an explosive mixture of gas and air containing 9 per cent natural gas may start a disastrous explosion of coal-dust. This is a very small volume, of gas, to cause such a result. Let us suppose that this amount of explosive mixture, as at the face of an entry which was 10 feet wide and the face was overcut to a depth of 6 feet and an upper layer of coal 2.5 feet thick had been removed, the recess so made would have a volume of 150 cubic feet. Furthermore, only 13 cubic feet of pure methane is needed in thin volume to produce this 9 per cent explosive mixture.

Jan 1, 1930

By David Schlain

This Bureau of Mines report describes a method for electrodepositing titanium diboride from a molten salt bath. Initially, the electrolyte is a mixture of LiBO2, NaB02, Na2 Ti03 , Li2Ti03, and Ti02? The cell is operated at 900° C in a dry, inert atmosphere with consumable anodes of titanium or hot-pressed titanium diboride (TiB2) powder. Agitation of the electrolyte is essential. Current densities may be 6 to 9 amperes per square decimeter (amp/dm2) with titanium anodes and 9 to 30 amp/dm2 with titanium diboride anodes. A current density of 6 amp/dm2 is equivalent to a plating rate of about 35 micrometers per hour. The adherence of the TiB2 deposit varies with the substrate material. It is most adherent on molybdenum and on 4130 steel that has been preplated with copper and nickel, less adherent on nickel, and still less adherent on Inconel and on 4130 steel without the preplate. Cathode and anode reactions are suggested.

Jan 1, 1976

By P. C. Good

Work was done to determine conditions necessary for efficient electrodeposition of aluminum from fused chloride electrolytes. Aluminum was deposited from a molten chloride salt electrolyte over a temperature range of 150° to 750° C. At lower temperatures in a heat-resistant glass cell, aluminum was deposited on stainless steel and on aluminum cathodes. The deposit was recovered in the form of light, feathery dendrites that could not be consolidated. At 750° C, molten aluminum was deposited at cathode current efficiencies as high as 90 to 100 percent on titanium diboride cathodes and in molten aluminum cathodes. Nitride-bonded silicon carbide was the best cell material, although porcelain was also used. The electrolyte consisted of a mixture of sodium and potassium chlorides in 1 to 1 mole ratio, containing aluminum chloride in concentrations ranging from 2 to 30 weight-percent in cells holding up to 1,000 grams of electrolyte. Generally favorable results were attained in studies made at temperatures greater than the melting point of aluminum.

Jan 1, 1966

By J. J. McClelland

The face area of a continuous mining section of an underground coal mine is the most dangerous area in the mine. Workers there are at nearly twice the risk of death or disabling injury than those in other parts of the mine. Despite extensive training of miners and improved equipment and mining methods, fatality and injury rates have remained constant during the past few years. It is clear that advanced research is necessary to apply new technologies or modify work procedures to solve the continuing problem of the loss of lives and the numerous injuries at the mine face. A U.S. Bureau of Mines research program is developing a Reduced-Exposure Mining System (REMS) that relocates personnel operating the mining machinery at the face away from the hazards to a nearby haven of relative safety. REMS uses proven technologies of computer automation and robotics to help control the operation of the mining machines at the face, while personnel are moved away to a nearby, safe control room. In this protected, well-ventilated environment, they can supervise or control the operation of the machines while viewing what the machine is doing using video and graphic display monitors.

Jan 1, 1994