Search Documents

1. In 2003, a total of 7,070 sand and gravel mining operations reported employment to the Mine Safety and Health Administration (MSHA). The largest percentage of all mining sectors was sand and gravel mines (49.1%). • Sand and gravel mines are found throughout all 50 states.

Feb 1, 2005

Coaxial cable structures form the subject of substantial theoretical and experimental investigations either directly related, or which can be extrapolated, to the communications needs and environments of U.S. coal mines. Communication systems based on "guided" waves, of which "leaky" coaxial cables are one implementation, are attractive candidates for providing a range of communication functions primarily along haulage ways, and possible also within sections up to the working face. (However, there are still strong reservations as to whether a practical coaxial cable sys tem could provide sufficient communications coverage within a section. ) In this Part, we present the results of some theoretical calculations of the performance of leaky coaxial cable communication systems. We also analyze the applicability of the theoretical and experimental results obtained by other researchers to the needs of U.S. coal mines. In particular, this investigation has been focused on the utility of relatively low cost, conventional, flexible, coaxial cable at frequencies covering the LF through HF bands and extending into the lower part of the VHF band, as opposed to relatively high cost, special semi-rigid, coaxial cable* at frequencies in the VHF and UHF bands. There are three major design alternatives for coaxial cable communication systems considered in this chapter: • Base station feeding a coaxial cable with high surface transfer impedance (holes in outer conductor, e.g., braid construction). • Base station feeding a coaxial cable with repeaters (U.K. experiments). • No base station, direct communication via a coaxial cable with periodic radiative structures.

Jan 1, 1974

By Charles H. Atkinson

The Rio Blanco massive hydraulic fracturing demonstration has been undertaken by the Bureau of Mines, Atomic Energy Commission, and a group of 15 industry participants. CER Geonuclear Corp. has been retained as program manager to evaluate the stimulation effects of very long fractures, suitably propped open in thick sections containing multiple intervals of low-permeability gas-bearing sands. The zone of interest for this demonstration includes Fort Union and Mesaverde sands from about 5,800 to 8,.200 feet deep in Rio Blanco County, Colo., about 1 mile from the site of the May 1973 triple nuclear detonation aimed at stimulating production from the same reservoirs. Drilling the test well and evaluating the reservoir prior to fracturing was funded by Government participants; fracturing and production testing will be funded by industry. The test well has row been completed at a total depth of 8,170 feet, and data obtained from logs, cores, production and drill-stem tests indicate reservoir conditions to be less favorable for gas production than anticipated. Structural position is lower than expected, resulting in higher water saturation than was determined for the same sands at the nuclear fracturing location. The lower sands of the Fort Union sequence appear to have higher shale content than has been encountered in other wells in the area. Despite the likelihood that gas productivity will be undesirably low following stimulation, the industry participants decided to proceed with the stimulation program with the thought that the resulting data would be useful. The success of the stimulation test probably will have to be judged by production increase rather than by production volume.

Jan 1, 1975

By Alfred E. Schwaneke

The surface tension from 240° to 844° C and the density from 236° to 583° C of 99.999 percent purity liquid tin has been measured using the maximum-bubble-pressure method. Results for surface tension (y) show y (dynes/em) = 566.84 -4.76 X 10-2 T (° C) with a standard error of 1.9 dynes/cm. Results for density (p) show p (g/cm3) = 7.16 -6.3 X 10-4 T (° C) with a standard error of 0.012 g/cm3. Comparisons with other data found in the literature are discussed. The experimental results are considered to be as good as any data presently available.

Jan 1, 1970

By H. F. Yancey

A relatively large proportion of the coal produced in the state or Washington, especially in the coking coal areas is of fine size; hence washing by means of coal-washing tables to reduce the ash content is commonly practiced. For this reason the program of research in coal washing conducted jointly by the U. S. Bureau of mines and the College of Mines, University of Washington, has given special attention to the mechanism of the separation of coal from its impurities as affected by the coal-washing table with the object of

Jan 1, 1931

By Kenneth J. Miner

Pittsburgh bed and Lower Freeport bed coals were tested in the U.S. Bureau of Mines two-stage froth flotation pilot plant, which utilizes a new flotation process to remove pyritic sulfur. The process consists of a first-stage coal flotation step to remove coarse, free pyrite and other refuse in the tailings. The clean coal froth concentrate is then repulped and treated with a coal depressant, a pyrite collector, and a frother to selectively float the remaining pyrite in a second stage. Results in the pilot plant were excellent, comparing well with those obtained in laboratory batch tests. That is, about 70 percent of the pyrite present in the Pittsburgh bed coal and about 90 percent of the pyrite present in the Lower Freeport bed coal were removed with excellent final clean coal recoveries.

Jan 1, 1973

By H. F. Yancey

A relatively large proportion of the coal produced 1n the State of Washington, especially in the coking coal areas is of fine size; hence washing by means or coal-washing tables to reduce the ash content is commonly practiced. For this reason the program of research in coal washing conducted jointly by the U. S. Bureau of Mines and the College of Mines, University of Washington, has given special attention to the mechanism or the separation of coal from its impurities as effected by the coal-washing table with the object of increasing its efficiency. Previous work has evaluated the role of stratification the influence of size, specific gravity and respective shapes of particles in the feed, and the affect of hindered-settling classification of the feed prior to tabling.

Jan 1, 1931

By J. A. Ruppert, P. M. Sullivan

A process was developed on a laboratory scale in which iron contained in galvanizers ' zinc dross and aluminum contained in scrap zinc die - cast alloy were removed simultaneously . Melting both types of scrap together in the proper proportions resulted in formation of solid intermetallic Fe₂ Alg , which was readily removed from the melt by filtration and centrifugation . Recovery was 87 to 92 percent of the available zinc . Refined filtrate contained 0.02 percent iron and 0.20 percent aluminum. Aluminum content was further reduced to less than 0.01 percent by fluxing with zinc chloride . Low temperatures employed and inexpensive equipment requirements make the process commercially attractive .

Jan 1, 1964

By John Durkin, Roy J. Greenfield

This report discusses the configuration and system deployment for the postdisaster surface seismic system for detecting and locating trapped miners. It analyzes the results of 15 field tests to define a signal model, background noise levels, and subarray performance. A waveform modeling procedure is described and compared with observed waveforms. The resulting similarity indicates that the major factors affecting the signal amplitude, waveform, and spectral character are understood. A model is presented which gives the signal amplitude as a function of source type, source depth, and horizontal off- set between source and receiver. Using this model a curve is presented which gives the range at which a signal will be detected for different signal and noise levels. Finally, and most important relative to the mission of the sys- tem, the ability of the system to detect signals on one or more subarrays is put into a probabilistic framework. For a strong source it is almost certain that a subarray directly over the source will detect the signal. After signal processing, it is highly likely that signals will he detected on sufficient subarrays to locate the trapped miner. Location errors have been found to be less than 100 ft in the majority of cases. Techniques have been used that can reduce the location errors to this level even when soil layer variation between subarrays is severe.

Jan 1, 1981

By John F. Papp

The Bureau of Mines has sampled microstructure of low-pressure flat flames by mass spectrometer for normal methane-oxygen-argon and for methane-oxygen-argon-bromotrifluoromethane flames. The physical and chemical phenomena, and the method of analysis of mole fraction data to evaluate net reaction rates are here considered in detail. Included is a computer program listing with output on one flame. Chemical species considered are CH4 , CO, CO2, H, H20, OH, Ar, H2, O2 , O, H2CO, CH3 , CF3Br, HF, HBr, Br, CH3Br, HCO, F2CO, CH2 CF2 , H02.

Jan 1, 1975

By Steven J. Schatzel, Gerrit V. R. Goodman, Robert B. Krog, C. Özgen Karacan, Gabriel S. Esterhuizen

Although longwall mining productivity can far exceed that of room-and-pillar mining, the total methane emissions per extracted volume associated with longwall sections are generally higher than those for continuous miner or pillar removal sections. Increased face advance rates, increased productivities, increased panel sizes, and more extensive gate road developments have challenged existing designs for controlling methane on longwalls. Methane control research by the National Institute for Occupational Safety and Health (NIOSH) recently examined a number of practices designed to maintain concentrations in mine air within statutory limits and consistently below the lower explosive limit. These included a reservoir modeling approach to predict methane inflows in gate road entries. The outputs sug­gested that emission rates in the gate roads decreased with the use of shielding boreholes and increased degasification time. Also, mining perpendicular to the face cleats liberated more gas into the mine workings, emissions were almost a linear function of Langmuir pressure and volume, and emissions were inversely related to sorption time constant. Subsequent simulations predicted changes in methane drainage using in-seam boreholes. The results showed that longer degasification times resulted in lower face emission rates. Premining degasification produced more methane than that produced during panel extraction, a fact attributed to the already decreased methane content of the coalbed. This work concluded that longer premining degasification periods would be more advantageous to the operator. The industry trend toward increasing longwall face width can produce increased methane emissions from the face due to a higher volume of cut coal on the face conveyor. Two methods were used to estimate face methane levels on longer faces. In the first method, segmented methane data were extrapolated for greater face widths. The second method estimated emissions contributions from the shearer, face conveyor, panel belt, longwall face, and ribs, and summed these for wider panels. Permeability changes in the gob behind the longwall shields were estimated using a NIOSH-developed numerical model. The results showed that permeability was highest near the edges and corners of the gob.

Jan 3, 2008

By David W. Houseknecht

Probabilities of encountering coalbed discontinuities during vertical or horizontal drilling in a specific coalbed can be estimated based on analysis of mined-out areas of the coalbed where the size, shape, orientation, and distribution of discontinuities are known. The result-ant probability estimates can be applied to cost-risk evaluations of drilling programs proposed for exploratory, developmental, or methane drainage purposes in undeveloped areas of that coalbed. Data compiled from mine maps of the Beckley Coalbed in southern West Virginia were used to estimate the probabilities that discontinuities would be encountered in two illustrative hypothetical drilling programs--one for drilling vertical boreholes and the other for drilling horizontal boreholes. Analysis based on a mined-out area of the Beckley Coal bed indicated that vertical methane drainage boreholes spaced 1,000 feet apart in a square grid pattern would each have a 29 percent probability of encountering a discontinuity in a geologically unexplored area of the coalbed. It was also determined that exploratory vertical drilling could locate most of the discontinuities if a borehole spacing of 2,500 feet were used. For horizontal drainage boreholes in the Beckley Coalbed, the analysis indicated a linear relationship between hole length and the probability of encountering a discontinuity.

Jan 1, 1982

By Neil B. Young

Carbonate minerals constitute a major fraction of the oil shale in Colorado's Green River Formation. Quantification of carbonate minerals is important for the characterization of oil shale, particularly because of their thermal activity in production of oil from shale. The carbonate minerals found in this oil shale are nahcolite (NaHCO3), dawsonite [NaA1(OH)2CO3], dolomite [(Mg1-xFx)Ca(CO3)2], calcite (CaCO3), and ferroan [(Mg1-xFex)CO3]. Although carbonate minerals can be removed by acid extraction from the balance of the oil shale, direct determination of carbonate minerals is complicated by the occurrence of the same cations in more than one mineral. A method for assigning the acid-soluble cations to the individual carbonate minerals was developed from two assumptions based on oil shale geochemistry: (1) Calcite and ferroan do not occur together, and (2) the ratio of iron and magnesium is the same in dolomite and ferroan. These assumptions were tested by the Bureau of Mines by applying the technique for assigning cations to 219 samples from the saline section of the formation. The reported carbonate mineral amounts were compared statistically with X-ray diffraction peak heights, verifying the cation assignment method.

Jan 1, 1975

Prevention of coal-mine explosions depends largely upon thorough knowledge of the causes that initiate explosions. A review of coal-mine explosions in one geographical area when supplemented by nationwide data of similar nature, should serve as a guide for the adoption of measures for explosion prevention. Explosions in bituminous-coal mines of the United States during the 10 years ended December 31, 1932, ranked third in the causes of fatal accidents and constituted 16.1 percent of all fatal accidents in bituminous mines. Kentucky now ranks fourth in coal output in the coal-producing States of this country; a study of the coal-mine explosions in this state will be of definite interest locally among coal-mining people, as well as to those in the coal-mining industry who are concerned in preventing coal-mine explosions. This circular reviews gas and dust explosions in Kentucky coal mines to show their hazards, to point out the influence of certain factors in causing explosions, and to indicate the effectiveness of preventive measures.

Jan 1, 1934

By N. S. Dalal, B. Jafari, X. Shi, M. M. Suryan

"It is well known that prevalence and severity of coal worker's pneumoconiosis (CWP) differ markedly in different regions and mines despite comparable exposures. These variations in the pathogenicity of different coal mine dusts can only partially be explained by the mineral composition of the coal mine dust and the rank of coal. Laboratory studies also do not correlate with the human experience. One major difference between human exposure and laboratory studies is that the coal miner breathes dust from freshly broken coal, while the animals or cells are exposed to stale dust. In an effort to find biochemical clues for resolving this apparent paradox, we have carried experiments to detect differences in chemical reactivities of fresh versus stale coal dust from several U.S. coal mines. Electron spin resonance (ESR) was used as a technique for the direct detection of the concentration and reactivity of free radicals. ESR measurements of freshly ground coal dusts of different ranks and composition showed significant differences in the amount and reactivities of the organic free radicals produced. The half-lives and reactivity patterns of these newly formed species of free radicals seem to correlate with the expected toxicity and pathogenicity of the dust, thereby, providing new clues to the biochemical mechanisms and pathogenesis of CWP. Similar detection of free radicals in freshly crushed quartz suggest that free radicals might play a significant role in the pathogenicity of quartz in causing fibrosis and eventually silicosis.IntroductionThe pathogenesis of coal workers' pneumoconiosis (CWP) has been an important topic of concern for decades, but the mechanism of CWP is still not understood. It is well known, for example, that the prevalence and severity of CWP differ markedly in different regions and mines despite com¬parable exposure'(1,2) but these observations can only par¬tially be explained by differences in mineral composition and rank of coal (3-5) Specifically, while epidemiological studies of coal miners indicate (1,2) that the effectiveness of coal in producing CWP correlates roughly with the rank (i.e. %,carbon content) of coal, such correlation has not been established via biological studies.(4-6)"

Mar 1, 1989

By R. K. Koch

The vapor pressures of liquid molybdenum and liquid zirconium were determined by the Langmuir free-evaporation method. An electron-beam furnace with a water-cooled copper crucible was used for melting. Temperature was measured with a two-color ratio pyrometer. The vapor-pressure data led to the following equations: [log p (atm) = 5.429 - 28,380 T for liquid molybdenum in the range 2,890° to 2,990° K, and log p (atm) = 6.521 - 30,940 T for liquid zirconium in the range 2,229° to 2,795° K.] Third-law evaluations of each data set gave mean heats of sublimation (298.15° K) of 157.6 ± 1.8 kcal/mole and 148.4 ± 2.4 kcal/mole for molybdenum and zirconium, respectively, where the uncertainties are two standard devia¬tions. Second-law standard heats of sublimation determined from sigma plots and tabulated enthalpies were 143.5 ± 2.7 kcal/mole and 149.2 ± 3.8 kcal/mole for molybdenum and zirconium, respectively. The better agreement in heats of sublimation for zirconium is attributed to the 566° K temperature range studied which permitted a more accurate definition of the vapor pressure curve than could be obtained from the 100° K span for molybdenum. This supposition was verified by making a sigma-prime plot which utilized solid vapor pressure data for molybdenum to extend the evaluation range by 800° K. This gave a standard heat of sublimation of 155.2 ± 1.6 kcal/mole which is in good agree¬ment with the third-law value. The plot also gave a standard entropy of sublimation (298.15° K) of 35.73 ± 0.48 eu.

Jan 1, 1968

By W. W. Adams

Reports received by the Bureau of Mines, Department of Commerce, from State mine inspectors, for November, 1930, showed that 219 men were killed in the coal mines of the United States during the month, an increase of 25 over the previous month and 33 over November, 1929. On the other hand the production of coal decreased, the output of 43,329,000 tons in November being 8,397,000 tons less than in October and 9,005,000 tone less than in November a year ago. The larger number of fatalities accompanied by a smaller output of coal resulted in a higher death rate4 per million tons in November than in the same month last year or in October, 1930. The November rate was 5.05, as compared with 3.55 for November, 1929 and 3.75 for October, 1930. The increase in the rate for the industry as a whole was chargeable entirely to bituminous mines, as the anthracite mines had fewer fatalities in November than in either of the previous months to which reference has been made. Reports for bituminous mines alone showed that accidents at this class of mines resulted in a death rate of 5.12, based on 195 fatalities and a production of 38,122,000 tons. This rate indicated an increase of 55 per cent over the rate for October, of the same year, and 72 per cent over the rate for November, 1929. The October record was 146 fatalities and 44,150,000 tons, and that for November a year ago was 138 deaths and a production of 46,514,000 tons.

Jan 1, 1930

By W. M. Weigel

"Sand is one of the most useful and, fortunately, one of the most common mineral commodities. By far the largest proportion of the production is used in construction, including all forms of building, concrete and paving, sand for this purpose is produced in every State in appreciable amounts. Excluding send used for railroad ballast, molding sand stands not in tonnage produced, followed by glass sand.Special sands. In addition to the above, many grades of sands, with special characteristics, are used in industrial processes, and may be classed in a group as ""special sends"". This includes filter sand, sand blast sand, engine sand, abrasive send, fire or furnace send, special flooring sand, roofing sand used as a finish for prepared roofings and pottery placing sand sand blast and filter sand have been discussed in previous reports.Very few send companies depend upon the production of any one of these grades, as their source of revenue. They are generally especially prepared from the bank run of sand by different methods of screening or washing, or may, in some instances, be by-products from the production of ether grades. Many companies not now producing them might be able to supply local demands by a slight addition to their plant. In nearly all cases, they command a better price than the usual grades of building sand.Definitions and Properties.Engine sand, or traction sand, as it is sometimes called, is used to prevent the slipping of the driving wheels of locomotives, or other self-propelled vehicles, on wet or slippery rails. Its greatest use is, of course, for railroad locomotives, but street cars use considerable amounts and mine locomotives require its use. As the send must be very dry when used, most consumers have their can drying equipment, so it is often shipped damp, with its natural water content on what resulting from washing by the producer."

Oct 1, 1924

By M. C. Irani, Maurice Deul, M. G. Zabetakis, T. G. Bobick

This survey was conducted to determine the magnitude of the methane emission and control problem in U.S. bituminous coal mines. The resultant data indicate that the emission rate for any given coalbed depends primarily on the coal production rate and on mine depth, as well as on the nature of the coalbed and the surrounding strata. An excellent correlation was found between (1) the methane emission rate and (2) the product of coal production rate and mine depth for the mines in the Pittsburgh, Pocahontas Nos. 3 and 4, and the Illinois Nos. 5 and 6 coalbeds. The highest total emission rates found in U.S. bituminous coal mines were as follows, in million cubic feet per day: Monongalia County, W. Va., 39; Marion County, W. Va., 30.4; McDowell County, W. Va., 13.1; Washington County, Pa., 11.9; Greene County, Pa., 11.4; Buchanan County, Va., 21.6; Jefferson County, Ala., 10.3; and Franklin County, Ill., 6.6.

Jan 1, 1972

By E. J. Gleim

A list of permissible mine equipment, tested and approved previous to January 1, 1942, was published In Bureau of Mines Information Circular 7207.3/ The present list covers additional equipment approved during the calendar year 1942. The items have been numbered to indicate the order in which each type of machine or device was approved in its particular classification. Thus, Information Circular 7207 gives four air compressors on the Bureau's active list, and the present circular gives the fifth to be approved. Items 90 and 94 under Loading; Machines land Conveyors also appear in Information Circular 7207. These numbers are repeated hero to show that approval was granted during 1942 for additional voltages on machines previously listed one voltage only. Equipment listed in these circulars is approved by the Bureau of Mines only when found upon inspection and test to comply with minimum standards of safety as outlined in schedules prepared on the basis of many years of experience in dealing with safety problems of the coal-mining industry. The use of such equipment in mines known to be gassy, as well as in those which may become so, is earnestly recommended in the interests of safety. This circular is published so that the industry may be kept informed as to the many types of machines, devices, and lamps that arc available for reducing explosion and other hazards incidental to coal mining. The present paper and Information Circular 7207 together give the complete list of all available permissible .Mine equipment.

Jan 1, 1943