Search Documents

A knowledge of the mechanics of wave propagation through the earth is essential if reliable communication systems are to be designed for coal mine environments. To obtain a reliable basis from which accurate propagation predictions could be drawn, a series of theoretical studies have been prepared for the US Bureau of Mines by Mr. Ramsay Decker of Spectra Associates, Inc. through a subcontract with Collins Radio Group. These reports formulate the analytical techniques from which we may derive frequencies and antenna configurations that yield the optimum signal-to-noise ratios over the greatest distances in mine environments. The reports of sections 2 and 4 deal with analytical techniques for determining the signal-to- noise ratio within a mine environment for loop-to-loop and line source-to-loop antenna con- figurations. The analytical results of these reports were then implemented into computer programs to obtain predictions concerning through-the-earth signal propagation. These preliminary predictions are based on noise data compiled by Bensema, Maxwell and Stone, and WVU prior to the extensive research conducted by the National Bureau of Standards (NBS). These initial measurements indicated a 20- to 30-dB lower noise level than that measured recently by NBS. The recent NBS data is that used by Collins in the final predictions. The following outline indicates the order and subject matter treated in the subsequent sections: Section 2 - Signal-to-Noise Analysis for Loop-to-Loop Mine Communications Section 3 - The Horizontal Electric Dipole Section 4 - Signal-to-Noise Analysis for Down-Link Line Source Mine Communications Section 5 - LF Communication Section 6 - The Application of Recent NBS Noise Data to Mine Communications Section 7 - Analysis of Mine Communication Propagation Programs

Nov 15, 1974

By A. F. Cohen

When location guidelines are followed in choosing sites for fixed point velocity transducers for use in underground coal mine monitoring, mine air turbulence intensities <11% are generally expected at those sites. The objective of this Bureau of Mines investigation to determine the effect of turbulence intensities <11% on vortex shedding sensors and transducers. Measurements were made at velocity levels of interest for underground coal mine monitoring use (?200, ?500, ?1,000, ?1,500 ft/min). The effect of grid-produced turbulence intensities (2% to ?14%) on the output of vortex-shedding air-velocity transducers was less than ±10%.

Jan 1, 1985

By J. H. Hild

The Shanton magnetite-ilmenite deposits lie on the east flank of the Laramie Mountains, 43 miles northeast of Laramie, Albany County, Wyo. (fig. 1). The Shanton and other similar deposits in the Laramie Mountains were examined by Bureau of Mines engineers during 1942, 1943, and 1945, and a report2/ describing the results of a dip-needle survey and surface sampling was published in 1946. The Shanton deposits occur in a relatively flat section of the range at altitudes varying from 7,500 to 1,650 feet (fig. la). Prevailing rocks in the Shanton area consist of anorthosite with intrusive dikes of gabbro differentiates and granite. Titaniferous magnetite outcrops in five masses, which are separated at the surface by overburden and anorthosite.

Jan 1, 1953

By Robert Stefanko

Transients are results of sudden changes which take place in power systems and can be created by the opening and closing of switches and circuit breakers or the occurrence of a fault anywhere in the complex. Transients are of short duration, and the time during which they occur is an extremely small percentage of the total operating time. However, it is during these short periods that the greatest electrical stresses occur, mainly due to excessive currents or voltages. In extreme cases, system parts are damaged, and equipment failure follows. Safety can be further compromised because anomalous voltages can exist at machine frames. For several years, the electric utilities have been well aware of the serious nature of transients on their systems, but problems firmly believed to directly result from these phenomena are just now becoming apparent to the coal mining industry. The situation became discernible after the underground introduction of high voltage distribution systems (along with vacuum circuit breakers) and sensitive solid state electronic apparatus. In order to protect against such transients, knowledge about their characteristics and origin must be obtained.

Jan 1, 1974

By R. D. Govier

The U.S. Bureau of Mines has developed a thin-film X-ray fluorescence technique to rapidly determine Cu, Ni, Co, Fe, and Cr in super alloy leach liquors. Total analysis time per sample was less than 15 min, as opposed to several hours for traditional wet chemical methods. Precision and accuracy were checked by replicate analyses of solutions similar in composition to leach liquors, whose analyte concentrations were well known. Coefficients of variation for all elements were found to be less than 2 pet. With the exception of the results for Fe, all relative errors of estimation were also found to be less than 2 pet. Bulk liquids are not introduced into the spectrometer; thus, the potential for damage to the instrument by leakage of corrosive liquids is eliminated.

Jan 1, 1989

By M. H. Kline, Wing G. Agnew

"INTRODUCTION The Yancey-Crawford tract, located 1-1/2 nines east of Yancey station on the Norfolk & Western Railway in Rockingham County, Va. was from 1917 to 1941 considered an unusually promising manganese prospect. Because of the favorable geologic formations and because of the common occurrence of manganese in the district and Virginia's large production of these minerals from this area, geological report 3/ have listed this tract as the No. 1 prospect in the State. During World War I, extensive geologic studies were made to locate manganese deposits similar to those exploited at the Crimera mine near Waynesboro to alleviate this mineral shortage during the existing emergency.In September 1941 the Bureau of Mines started exploratory drilling on the tract in an effort to discover and block out reserves of manganese minerals as authorized by the 76th Congress under the Strategic Materials Act. After five drill holes wore sunk, the project was terminated October 1941."

Apr 1, 1948

By Hugo E. Camargo

In an effort to reduce Noise Induced Hearing Loss (NIHL) in the mining industry, the National Institute for Occupational Safety and Health (NIOSH) is conducting research to develop noise controls for mining equipment whose operators exceed the Permissible Exposure Level (PEL). The process involves three steps: 1) Noise source identification (NSI), 2) development of noise controls, and 3) evaluation of the developed noise controls. For the first and third steps, microphone phased array measurements are typically conducted and data are processed using the conventional beamforming (CB) algorithm. However, due to the size and complexity of the machines, this task is not straight forward. Furthermore, because of the low frequency range of interest, i.e., 200 Hz to 1000 Hz, results obtained using CB may show poor resolution issues which result in inaccuracy in the noise source location. To overcome this resolution issue, two alternative approaches are explored in this paper, namely the CLEAN-SC algorithm and a variarion of an adaptive beamforming algorithm known as Robust Capon Beamformer (RCB). These algorithms were used along with the CB algorithm to process data collected from a horizontal Vibrating Screen (VS) machine used in coal preparation plants. Results with the array in the overhead position showed that despite the use of a large array, i.e., 3.5-meter diameter, the acoustic maps obtained using CB showed "hot spots" that covered various components, i.e., the screen deck, the side walls, the I-beam, the eccentric mechanisms, and the electric motor. Thus, it was not possible to identify which component was the dominant contributor to the sound radiated by the machine. The acoustic maps obtained using the RCB algorithm showed smaller "hot" spots that in general covered only one or two components. Nevertheless, the most dramatic reduction in "hot" spot size was obtained using the CLEAN-SC algorithm. This algorithm yielded acoustic maps with small and well localized "hot" spots that pinpointed dominant noise sources. However, because the CLEAN-SC algorithm yields small and localized "hot" spots, extra care needs to be used when aligning the acoustic maps with the actual pictures of the machine. In conclusion, use of the RCB and the CLEAN-SC algorithms in the low frequency range of interest helped pinpoint dominant noise sources which otherwise would be very hard to identify.

Jan 1, 2009

By R. V. Ramani, S. Shankar

"The phenomenon of re-entrainment is seen in environments such as sand dune formation, soil erosion, fugitive dust emission and the spread of radionuclides from accidents involving nuclear weapons. A thorough review of existing literature reveals that work on re-entrainment of dust in mine atmospheres is scant. The present study was undertaken as a part of ongoing research at the Generic Mineral Technology Center on Respirable Dust at the Pennsylvania State University on the development of methods to predict ambient dust concentrations in mine atmospheres (Ramani, 1983). The contribution of re-entrainment to the spatial and temporal concentration of dust in mine airways is being studied. The research has included wind tunnel and in-mine studies.A set of seven experiments was performed under controlled conditions in the US Bureau of Mines' Lake Lynn Laboratory mine. Two types of source coal dust, anthracite and bituminous, were subjected to various airflow rates and were subjected to walking by two different individuals. Six sets of instruments were used along the test section for sampling airborne particles. The average air velocity just above the coal dust bed varied between 2.1 to 3.2 m/sec.Due to re-entrainment as a result of the airflow conditions, the average respirable dust concentration in the center of the mine airway increased to 0.09 mg!m3 (standard deviation= 0.03 mg/m3)from an initial value of 0.02 mg/m3. The concentration of all (total) airborne dust increased to 0.17 mg/m3 (standard deviation = 0.10 mg/m3) from an initial value of 0. 02 mg/m3. The action of people walking, however, caused higher amounts of re-entrainment. The average concentration of respirable and total dust at the center of the mine airway increased to values of 0. 28 mg/m3 (standard deviation of 0.12 mg/m3) and 1.53 mg/m3 (standard deviation of 1.0 mg/m3), from initial values of 0.03 and 0.05 mg/m3, respectively. Jr was observed that the dust concentrations were much higher near the floor, immediately at the end of the coal-dust bed.Depending on the level of activity and the amount of dust deposited in the mine airways, re-entrainment may become an important source of airborne dust in areas away from the point of actual mining."

Dec 1, 1996

By Perry G. Cotter

The objective of this investigation was to synthesize and investigate the properties of a high-temperature refractory material based on a combination of boron, silica, and magnesium. A magnesium-thermic reaction was used for the synthesis. X-ray examination of the product indicates that the crystalline portion of the composition is a combination of magnesium borides, magnesium silicate, and magnesium orthoborate. Chemical analysis of a representative sample shows, in weight-percent, boron 17.6, silicon 23.9, magnesium 17.8, and chromium 0.5. The balance is largely oxygen. The composition is resistant to high temperatures under oxidizing conditions and is stable in water, hydrochloric acid, and hydrogen. It has a low density (less than 3 grams per cubic centimeter) and a hardness value in the range of quartz. It has a melting point above 1,700° C. and can be hot-pressed to shape in the temperature range between 1,200° and 1,350° C. The properties described in this paper indicate that the material may have some uses as a high-temperature refractory, and because of its boron content it may have some value as a thermal-neutron-absorption material.

Jan 1, 1961

By George N. Aul

This report describes a method developed by the Bureau of Mines for sealing horizontal degasification holes so that they do not create a gas explosion hazard when intercepted by mining. A cement slurry is pumped into the hole through an injection pipe that extends to the back of the hole. Pumping continues until the slurry returns through the annulus to the hole collar. The hole is then shut in and the grout allowed to harden. Application of the procedure to six horizontal degasification holes at Eastern Associated Coal Corp.&apos;s Honey Run shaft is discussed.

Jan 1, 1979

By Jon C. Volkwein

The U.S. Bureau of Mines has developed a method to measure methane and other gases during the auger mining of coal. An intrinsically safe commercial gas detector with a built-in data logger was mounted in the center of the hollow conveying auger. A sampling head through the wall of the auger conducted a gas sample to the detector. Results showed that gas levels can be monitored on a continuous basis during the auger mining of coal and the data retrieved upon completion of the hole.

Jan 1, 1994

By Miles B. Royer

The experimental blast furnace has attracted increasing interest during the past decade as a practical means for investigating a broad range of blast-furnace smelting problems. Under experimental-furnace conditions, information can be obtained with less expenditure of time and raw materials and, therefore, at lower cost than comparable information could be obtained under industrial operating conditions. Furthermore, the experimental furnace may be operated beyond the range of smooth operation, even to failure, to delineate the limits of operability. Such deviation from normal operating practice would be economically intolerable in industrial operations where production and operating stability might be disrupted. The Federal Bureau of Mines experimental blast furnace at Bruceton, Pa., near Pittsburgh, has been operated and under development since 1951. However, the usefulness of this experimental data to industrial practice was somewhat nebulous in early experiments, and the correlation of the experimental blast furnace with the industrial blast furnace was not known.

Jan 1, 1961

By Scott Turner

Since my whole life has been spent in the mining business , I naturally tend to address my remarks particularly to the newly- graduated mining and metallurgical engineers among you . To a certain extent , all forms of engineering principles are involved in the training of the mining engineer , and most sorts of engineering are certainly utilized by him , so that every one of this graduating class is concerned with the field I propose to discuss . The fact that , beginning with to - day , you will always be styled engineers , indicates that you have passed successfully through preparatory school , and have survived the hard grind of the technical college . One object of your training here has been to instruct you in accurate , close , and clear thinking . Your minds have been taught to act directly , calmly . and always to the point . By now , you should know how to get facts , look far , and think through . You are supposed to be willing to recognize and adopt sound engineering principles and practices , in so far as they are known to you , and to furnish character , ability , and devotion to your calling . Some of you may have had a general college course before coming here to specialize in engineering . Where that has been possible , I hope it is the case , since a liberal educational course tends to make the alumnus more flexible and adaptable than the purely scientific graduate. The broader education enables one to change , with less serious loss , from one job to another; ready adaptability is a great asset ; the engineer should be capable of much more than a single special task . The necessary preliminary training for a professional occupation is intellectual in character , involving knowledge , and to some extent learning , as distinguished from mere skill . The well -balanced engineer is expected to embody a happy combination of theory and fact , of pure science and material reality ; experience shows that he is apt to give a good account of himself , once he gets the chance . For the long pull , the importance of unquestioned integrity can not be overemphasized . Leaders of big business sometimes have need for a man as agile and unscrupulous as a cat on a back fence ; on occasion , they may have to employ brilliant , smart , spectacular , and crafty people , but when the special purposes for which such men are hired have been accomplished , they are no longer wanted . Given natural health , intelligence , ability , and adequate training , probably the characteristics most admired in the young employee are steadiness , dependability , and loyalty . The last is the best . If you can not be simple , direct , and faithful in your dealings with your administrative superiors , no one will want you for long . I believe these points are of primary importance to the young engineer . Your groundwork must be right before you can get far . These personal characteristics are what eventually determine your relations with men and affairs . They are vital in the human engineering which may be a large part of your work .

Aug 1, 1932

By E. G. King

This report contains experimentally determined heat-content values for cerium dioxide and Columbium (niobium) dioxide in the temperature range from 298° to 1,800° K. There are no previous similar data for Columbium dioxide, and those for cerium dioxide have an upper limit of 373° K. The heat-content and corresponding entropy-increment data are presented in tabular form. Equations were derived to represent the heat contents and heat capacities. The data for cerium dioxide are entirely regular, but those for columbium dioxide show two previously unreported anomalies at 1,090° and 1,200° K.

Jan 1, 1961

By John H. Soulé

"INTRODUCTION Spodumene and lepidolite were shipped from the Harding pegmatite deposit, Taos County, N. Mex., in the period from 1930 to 1930. Tantalum minerals were noted as early as 1924 and described in 1931 3/ but no tantalum ore was shipped until 1942. The deposit was mapped and studied by geologists of the Federal Geological Survey and engineers of the Bureau of Mines late in 1942 and early in 1943, and a Bureau of Minus exploratory project was carried out in 1943. 4/ Thu following report presents the results of that project.ACKNOWLEDGMENTSIn its program of exploration of mineral deposits, the Bureau of Minos has as its primary objective the more effective utilization of our mineral resources to the end that they make the greates possible contribution to national security and economy. It i the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lovell B. Moor, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallugiical Branch, R. G. Knickerbocker, chief, analyzes samples and performs beneficiation tests. Both these branches are under the supervision of Dr. R. S. Dean, Assistant Director."

Dec 1, 1946

Objective To characterize the roof fall risk associated with underground limestone mining. Background During the first 5 years of this decade, more than one-fourth of the underground mining fatalities occurred as the result of fall of ground. The large openings in underground stone mines present limitations in observing ground conditions because of floor-to-roof heights ranging from 20 to 60 ft or more. Generally, the status of ground conditions in under-ground stone mines is based on observation and experience obtained during mining development. Some mines use monitoring instruments to gain information on roof conditions, but this practice is typically focused and localized to address issues in a particular area or section of the mine. The Roof Fall Risk Index (RFRI) described here provides a method of systematically characterizing the risk of roof falls to enhance the safety of mine workers. Approach As in many industries, a defective product signals the potential for failure. Similarly, defective rock or strata in an underground stone mine presents a potential risk. Assessing ground conditions relative to the concentration of defects observed provides a way to index or rate these conditions and the subsequent risk. Through observations at approximately 50 underground limestone mines in the United States, strata defects were categorized to develop a quantitative method for determining the RFRI. This method is specifically geared to underground lime-stone mines because strata defects are difficult to see and limited by the experience and knowledge of the observer. Overall, 10 defect categories were deter-mined: 3 that relate to geology, 4 that result from mine development, 2 that are indicative of the roof profile, and 1 that addresses moisture or water flow (see RFRI Chart 1). The defect categories are also weighted to reflect the conditions indicative of roof or strata movement or separation (categories 4 through 8). These weights are multiplied by the assessment value to determine the total category value. The benefit of using monitoring techniques to gain information on roof conditions is also factored into the RFRI for overall assessment of an area in the mine. Each defect category is assessed with a value of 1 to 5 based on parameters as defined in each defect category, with 5 indicating the highest degree or level of defect. The assessment value of 3 is also used when information on a parameter is unknown. The parameters for the defect categories are illustrated in RFRI Chart 2 for use in determining the assessed value. How It Works The RFRI provides a means to categorize the risk for roof falls in underground stone mines. The concept of this calculation is aimed at providing an indication of the level or degree of defect relative to the area of the mine examined. The RFRI for the calculation produces a distribution where RFRI values approaching 0 represent a stable condition and those ap-proaching 100 represent an unstable condition.

Oct 1, 2006

By T. A. Henrie, E. K. Kleespies

Electrolytic studies were conducted to determine the transfer rates of the alloying constituents from molten titanium anodes to solid titanium cathodes in molten salt systems . The metals , nickel , tin , copper , bismuth , and manganese , were selected on the basis of thermodynamic data and the melting point of the alloy system . The transfer of nickel , tin , and bismuth was very low . The content of these elements in the cathode was in the range of less than 0.01 to 0.001 percent . The copper transfer was 0.6 to 0.8 weight - percent in electrolytes containing titanium chlorides and 0.12 weight - percent in titanium fluoride salt systems . The manganese transferred at rates comparable to that of titanium . Highpurity titanium and titanium- manganese alloys of uniform composition were produced by electrorefining molten titanium alloys in chloride electrolytes . Comparisons are made between the calculated and the actual quantities of metal transfer .

Jan 1, 1964

By W. E. Wallace

Volume-rate-of-flow measurements were made of the flow of mercury through porous samples under conditions of no field, magnetic field transverse to the direction of flow, and transverse magnetic field and electric current to determine if a magnetic method might be potentially useful in the study of pore-size distribution. No change was observed in the flow rate from the application of a magnetic field alone. The application of both field and current produced an electromagnetic pumping action with or against the direction of flow, depending upon the direction of the electric current. This pumping effect was observed to be greater in a rectangular porcelain sample than the calculated value for an equal-Sized open channel.

Jan 1, 1969

By J. J. Drost

This Bureau of Mines investigation studied the effect of thermal treatments upon concentratability of a western Mesabi Range nonmagnetic taconite ore and is a sequel to Bureau of Mines RI 7567. Magnetic tube tests were used to develop the data needed to calculate separation efficiency, the primary measure of concentratability. A horizontal tube furnace was employed to heat treat and reduce the hematitic ore samples. The two variables studied were roasting temperature and cooling method. The manner of cooling, either by slow cooling or quenching in water, produced no significant difference in concentratability. Roasting temperatures employed ranged from 500° to 1,000° C, and a temperature of 650° C effected the best concentratability. The temperature of 650° C correlated with the most effective roasting temperature for grindability.

Jan 1, 1973

By James V. Kelly

During the winter of 1946 and the spring of 1947, the Bureau of Mines conducted an investigation and drilling program in the vicinity of the village of Fairplay, Wis. Fifteen diamond drill holes totaling 2,457.6 feet of bore were completed. This work was part of a general study of the zinc-producing area of southwestern Wisconsin and had the particular purpose of investigating a structural trend, determined by the Federal Geological Survey, in an area some distance from known ore bodies or active mines.

Jan 1, 1948