Search Documents

By Robert C. Dyni

This report details the investigation of multiple-seam longwall subsidence conducted by the U.S. Bureau of Mines from 1978 to 1989. A field investigation monitored ground surface movements over four upper-seam longwall panels and six lower-seam panels. The characteristics of the subsidence occurring as a result of mining these panels are examined; in particular, the angle of draw, subsidence development, total magnitude and areal extent, and critical width are evaluated and discussed. Comparisons are also made between the characteristics of multiple-seam longwall subsidence and single-seam longwall subsidence that occurred at the same site.

Jan 1, 1991

By Harry R. Nicholls

Preliminary tests on presplitting rock in the presence of an in situ static stress field were undertaken to study the influence of a horizontal static stress field on the creation of a vertical presplit fracture plane. These tests indicated that it is easier to fracture the rock parallel to the in situ maximum compressive stress than in other directions. Instrumented shots indicate that the interaction of stress waves generated by the detonating charges is probably responsible for starting tensile fractures between shotholes and that expanding gases may propagate these initial cracks by a wedging action. The hole spacing for presplitting appears to be equal to the half wavelength of the stress wave. However, wider hole spacing appears feasible if the initial fracture is started by closer hole spacing.

Jan 1, 1966

By S. C. Termes

The Bureau of Mines conducted research on the flocculation of various minerals with insoluble cross-linked starch xanthate (ISX) to determine its potential as a beneficiation technique for low-grade, highly dissem-inated ores and for selective desliming. Covellite, chalcocite, pyrite, pyrrhotite, chalcopyrite, bornite, sphalerite, galena, and molybdenite fines flocculate with ISX. Floc formation, floc size, and settling rate are dependent on pH, with the pH dependence differing for each mineral. Quartz is not flocculated by ISX. Experiments to obtain selective flocculation of sulfides from quartz were attempted. Good selectivity was only obtained for the bornite-quartz system. postflocculation separations resulted in flocculated bornite in grades as high as 92 pet. Evidence is presented that the flocculation of many of the sulfide minerals with ISX may involve covalent bonding of the xanthate group to lattice metal site(s).

Jan 1, 1983

By Carlton E. Brown

Broom and Yant6/ recently described a. microprojection method for determining the particle-size distribution and number concentration of samples of dust collected from the air by such samplers as the Owens jet dust counter) and the thermal precipitator8/ . This method was developed to obviate or reduce the eyestrain consequent to the regular filar-micrometer method9/ and to save time and work. The article stated that work was in progress on a micrcprojection method for counting impinger dust samples; this article describes the method developed. ACKNOWLEDGMENTS The assistance of the personnel of the ventilation Department of the Anaconda Copper Miring Co., Butte, Mont., in developing this method and particularly in suggesting a suitable material to use for the microprojector screen is sincerely appreciated. Much of the work was done in the laboratory of the Anaconda Copper Mining Co. on samples collected in Butte mines during a cooperative study with this Bureau.

Jan 1, 1938

By Robert F. Randolph

Research on improving haulage truck safety, started by the U.S. Bureau of Mines, is being continued by its successors. This two-part article reports the orientation of the renewed research efforts, beginning with an update on accident data analysis, the role of multiple causes in these accidents, and the search for practical methods for addressing the most important causes. Fatal haulage accidents most often involve loss of control or collisions caused by a variety of factors. Lost-time injuries most often involve sprains or strains to the back or multiple body areas, which can often be attributed to rough roads and the shocks of loading and unloading. Part II will describe research to reduce these accidents, including improved warning systems, shock isolation for drivers, encouraging seatbelt usage, and general improvements to system and task design.

Jun 1, 1997

By Robert F. Randolph

Research on improving haulage truck safety, started by the U.S. Bureau of Mines, is being continued by its successors. This two-part article reports the orientation of the renewed research efforts, beginning with an update on accident data analysis, the role of multiple causes in these accidents, and the search for practical methods for addressing the most important causes. Fatal haulage accidents most often involve loss of control or collisions caused by a variety of factors. Lost-time injuries most often involve sprains or strains to the back or multiple body areas, which can often be attributed to rough roads and the shocks of loading and unloading. Part II will describe research to reduce these accidents, including improved warning systems, shock isolation for drivers, encouraging seatbelt usage, and general improvements to system and task design.

Jan 1, 1997

By John P. McDonnell

Coal mine bounces and bursts are major problems facing U.S. mine operators. Bounces and bursts have the potential to inflict severe injury on mining personnel, damage equipment, and cause mine closures. High- stress conditions, at or near the working face, are the common denominator in the burst problem, If mine operators can locate high-stress and potentially burst-prone zones, they can then use stress-relief methods to control the burst condition. One method of locating the high-stress zone is the probe-hole-drilling or drilling-yield method. Probe-hole drilling is used frequently in Europe, the U.S.S.R., and Japan as a means for locating potential burst zones. Consequently, the Bureau of Nines performed tests in the laboratory and in a deep, burst-prone western mine to analyze probe-hole drilling. The in-mine method, very simply, involves drilling a hole into the coal seam and measuring the volume of cuttings obtained. A certain volume of cuttings can be expected from a certain diameter and length drill hole. A significant increase in the volume of cuttings means the zone around that particular hole is highly stressed. In-mine use of the drilling yield method has shown it to be a useful tool for locating highly stressed and potential burst zones. Results from laboratory testing confirm that high stress applied tri-axially to a cube specimen will cause a significant increase in the volume of cuttings from a small-diameter drill hole in the specimen.

Jan 1, 1988

By John H. Soule

The Royal John mine was examined in November 1942 by a mining engineer of the Bureau of Mines, who proposed development of the Royal John and other properties in the area. Geologists of the U. S. Geological Survey studied the area in 1943 and 1944 and made definite recommendations. Also, in 1943 the Peru Miring Co. mapped the Royal John and did considerable diamond drilling. The Bureau of Mines started the Royal John portion of a project pertaining to the general district in April 1944. This project was completed in Juno 1945. The work, consisting of diamond drilling, was supervised by Robert O. Hill, mining engineer, and the results were published in Report of investigations 3904, Exploration of Grey Eagle, Grandview and Royal John Claims, Grant County, N. WIC. In 1947 and 1948 the Royal John was re-examined by a Bureau engineer, and additional development to increase the reserves of low-grade lead-zinc ore was proposed. This project was started in August 1948 and completed in Juno 1949.

Jan 1, 1950

By Carlton E. Brown

Brown and Yant6/ recently described a microprojection method for determining the particle-size distribution and number concentration of samples of dust collected from the air by such samplers as the Owens jet dust counter7/ and the thermal precipitator8/. This method was developed to obviate or reduce the eyestrain consequent to the regular filar-micrometer method9/ and to save time and work. The article stated that work was in progress on a microprojection method for courting impinger dust samples; this article describes the method developed. ACKNOWLEDGMENTS The assistance of the personnel of the Ventilation Department of the Anaconda Copper Mining Co., Butte, Mont., in developing this method and particularly in suggesting a suitable material to use for the microprojector screen is sincerely appreciated. Much of the work was done in the laboratory of the Anaconda Copper Mining Co. on samples collected in Butte mines during a cooperative study with this Bureau.

Jan 1, 1938

By L. A. Haas

The Bureau of Mines conducted bench-scale leaching tests with recycled spent copper electrolytes and copper-nickel mattes produced from the Minnesota Duluth Complex concentrates. This report describes the first stage of an overall two-stage leach operation. The objective of this research was to determine the matte-leach technology required to convert spent copper electrolyte into an enriched nickel liquor suitable for a nickel refinery and there-fore essentially free of copper, iron, and sulfuric acid. The experimental variables investigated were matte composition, particle size, spent electrolyte content, pulp concentration, oxygenation, temperature, and time. The time required to produce an enriched purified nickel liquor decreased with increasing pulp concentration, temperature, and oxygenation, but increased with increasing particle size and electrolyte copper and acid content. Nickel-rich (about 50 g/l) liquors at a pH of about 4 and containing less than 1 g/l of copper and iron were produced at 70° C by leaching minus 325-mesh low-iron (less than 5 pct) matte for 8 hours with spent electrolyte containing 22.4 g/l Cu, 28.9 g/l Ni, less than 0.1 g/l Fe, and 50 g/l H2S04 at a pulp concentration of 1 kg of matte per liter of spent electrolyteo Varying the nickel content of the spent electrolyte from 11 to 101 g/l appeared to have no appreciable influence on the matte leaching characteristics.

Jan 1, 1981

By R. O. Dannenberg

A metallic displacement process, utilizing easily available steel wool or steel window screen, was devised and successfully used for the recovery of silver from waste photographic fixing solutions. Laboratory and prolonged commercial-scale testing established that the iron filament type unit will efficiently precipitate silver, as a high-grade sludge, from acidic waste photographic fixing solutions ranging in grade from less than 1 to over 10 grams of silver per liter. Data and design information are presented to facilitate the construction and operation of a practical unit of any desired size. A smelting process for recovering pure silver from precipitated sludge containing 27 to 80 percent silver was devised.

Jan 1, 1968

By E. L. Burwell

Preliminary results of an in situ oil shale retorting experiment conducted by the Bureau of Mines in a shallow bed of Green River oil shale at Rock Springs, Sweetwater County, Wyo., are described. Eleven wells were drilled into a 20-ft-thick section of the shale lying between 68 and 88 It deep, and attempts were made to connect the wells through the shale with a fracture system created by application of high-voltage electricity (electro-linking), hydraulic fracturing, and explosive fracturing. Ignition of the shale through the central well was easily achieved with a propane burner, and shale oil began to collect in three wells within 3 hours. Propane injection was discontinued after 7 days, and combustion continues, although attempts to control the direction of the combustion front have been unsuccessful. Production rates as high as 4 ½ barrels of nil per day have been recorded, but too little is known about underground conditions to permit an estimate of recovery efficiency at this time.

Jan 1, 1969

By L. B. Pankratzt

The heat content above 298.15° K of ferroelectric lithium columbate (LiCbO3) was measured to 1,770° K. The Curie temperature was determined to be 1,450° K, the melting point 1,540° K, and the heat of fusion 16.94 kcal/mole. Heat content and entropy increments have been tabulated for the temperature range from i98.15° to 1,800° K. Heat contents are also given in equation form.

Jan 1, 1966

By J. W. Jensen

Alloys of manganese and copper containing from 65 to 80 percent manganese possess mechanical strength and vibration-damping capacity in an unusually high degree. The success of their use in reducing vibration in structures depends, to some extent, on their fatigue properties. This report describes the results of fatigue tests on alloys of four compositions. Three metallurgical conditions were investigated for each alloy. Or the basis of the data in this report, the general rule that vibration-damping manganese-copper alloys are comparable to mild steel in hardness and strength may be extended to include fatigue strength. Methods for casting and fabricating these alloys were described in a previous report,4 which contained data on the mechanical and damping properties of the solid-solution alloys, and on alloys aged for 2 hours at 450° C. The aging heat treatment of solution-treated alloys results in optimum mechanical and damping properties throughout the range of specified composition. However, in the present work, measurements also were made on alloys aged for 2 hours at 500° C., because it was theorized that the additional precipitation of a-manganese under these conditions might have a pronounced effect on the fatigue strength of the alloy.

Jan 1, 1961

By H. Kenworthy

A zinc-pyrite ore from the Gray deposit in Jo Daviess County, Ill., was successfully concentrated on a laboratory scale. Initially, drill cuttings were submitted for separation of zinc and iron concentrates. Subsequent to mine development, a large sample of coarse ore was submitted to ascertain its amenability to sink-float treatment to produce a low-grade zinc-iron concentrate and discard a clean tailing. The samples of ore were submitted to the Rolla Metallurgical Branch by the Mining Division of the Federal-Bureau-of Mines. They were obtained during the recent war as a part of the extensive government program to increase metal production through exploration for new mineral deposits and investigation of old mineralized areas. The first sample consisted of about 3,000 pounds of drill cuttings collected, during the Bureau?s churn and diamond- drilling program. The second sample was taken at a later date, after Tri-State Zinc, Inc., had opened the deposit and commenced milling the ore. This sample consisted of a ?ton-of mill feed crushed through 2 inches and collected over a period of 3 days.

Jan 1, 1949

By Constantine C. Popoff

During 1946 several limestone deposits near Fortson, Snohomish County, Wash., were examined by the Bureau of Mines. These examinations were part of a long-range investigative program of regional mineral supplies required by the anticipated industrial development of the Pacific Northwest. The .study outlined in the following paper was specifically undertaken to disclose new sources of high-purity limestone and to appraise, their economic aspects. The deposits examined -namely the Galbraith, Climax, and Hi, Hi -are somewhat similar in physical features and geologic environment. They are lenticular and belong to the same formation of metamorphosed sediments that underlies the prominent Whitehorse Ridge.

Jan 1, 1949

By Ralph H. Espach

In the spring of 1943, when it was evident that the Tensleep sandstone in the Elk Basin field, Wyoming and Montana, held a large reserve of petroleum, Bureau of Mines engineers obtained samples of oil from the bottom of nine wells and analyzed them for such physical characteristics as the volumes of gas in solution, saturation pressures or bubble points, shrinkage in volume caused by the release of gas from solution, expansion of the oil with decrease in pressure, and other related properties. The composition of the gas in solution in the oil was studied. The pressures and temperatures existing in the reservoir and the productivity characteristics of the oil wells were determined. The data obtained indicate that the oil in the Tensleep reservoir of the Elk Basin field has unusually varying physical characteristics, such as a saturation pressure of 1,250 pounds per square inch absolute and 490 cubic feet of gas in solution in a barrel of oil at the crest of the structure, and a saturation pressure of 530 pounds per square inch absolute and 134 cubic feet of gas in solution in a barrel of oil low on the flanks. The hydrogen sulfide content of the 6a r; in solution in the oil varies from 18 percent for oil on the crest to 5 percent for oil low on the flanks of the structure. Of even greater significance is the fact that these and other variable characteristics of the reservoir oil are related to the position of oil in the structure. Many geologists and petroleum engineers have considered all the oil in a petroleum reservoir to have uniform physical characteristics and that equilibrium conditions prevailed in all underground accumulations of oil and gas. That such is not always so is borne out by the results of the study made by the writers.

Jan 1, 1951

By D. Harrington, R. R. Sayers

For several years the writers have been studying various phases of the effect of air conditions in metal mines upon underground workers ; in 1918 a short study was made in certain hot and deep mines and brief reports were issued in the Engineering and Mining Journal ( August , 1920) and in the U. S. Public Health Reports (Vol . 36 , No. 4 , January 28 , 1921 ) . In 1921 a more extended study was made (also in hot and deep metel mines ) with intent to determine the limiting conditions imposed upon underground workers by the physiological effect of various air movements , temperatures , and humidities , with and without work . It is the purpose to publish a series of short papers on this later investigation , each paper to consider one particular phase of the work . The present paper deals with the effect on body temperature and pulse rate in still air as compared with moving air of temperatures from 90 to 100° F . and 100 per cent relative humidity, the subjects at rest .

Apr 1, 1923

By James A. Whelan

The Bureau of Mines sponsored research studies of variables in rotary drilling, done in the Department of Mineral Engineering, University of Minnesota. By studying carefully controlled drilling with good instrumentation, it was hoped to obtain a better understanding of rock failure during drilling and of the stresses in drill bits during drilling. Experimental procedures and equipment are described. From these studies it was concluded that 1. Thrust requirements, other things being equal, are proportional to the total length of cutting edge in the bit. 2. Data from penetrating a wedge into rock under thrust only are not directly applicable to rotary drilling. 3, In rotary drilling the initial wear on a bit greatly decreases penetration rate under any given set of conditions; however, after initial wear the effect of wear on penetration rate is reduced. 4. An increase in rotary speed increases the overall penetration rate but decreases the penetration per revolution. 5. An increase in thrust increases the overall penetration rate and the penetration per revolution. 6, Torque on a drill bit is proportional to both penetration rate and bit diameter. 7. For small-diameter holes full-hole drilling will save both drilling time and energy compared with pilot drilling followed by reaming; for large-diameter holes pilot drilling-reaming is advantageous in both respects,

Jan 1, 1962

By H. G. Iverson

As a part of the program of investigation of domestic sources of manganese ore, mining engineers of the Bureau of Mines examined and sampled three properties in the vicinity of Winnemucca, Nev. As the ores were too low grade for direct production of ferromanganese, they were tested for their amenability to concentration by ore-dressing methods. Two samples of ore were procured by examining engineers of the Bureau of Mines from several outcrops in the Pollard Canyon area, Pershing County, about 30 miles southeast of Winnemucca. The manganese occurs in relatively small lenticular bodies as secondary replacement deposits in chert and quartzite. The first sample represented average run -of -mine ore as exposed in the Pollard Canyon deposits. Sample 2 was composed of hand-sorted, high-grade ore.

Jan 1, 1954