Search Documents

By R. J. Leary

The natural gas-air burner described in this report was designed and constructed to meet the thermal requirements of a convective process for heating steel scrap. This process involved downward combustion of natural gas with air, blending the combustion products with diluent air, and then passing this tempered stream of gases downward through a porous bed of steel scrap contained in the furnace chamber. The scrap would be heated to a temperature limited by the adiabatic flame temperature of the gas stream in a period that depended on the rate at which heat was supplied per unit of bed cross section. The temperature of the gas stream would be limited to that beyond which an objectionable degree of oxidation would occur; for carbon steel this limit had been found to vary from 1,900° to 2,100° F. with the superficial velocity of the gas stream. The productivity of the process was dependent on the rate of heat input per unit of furnace cross section; for the 3-foot-diameter experimental furnace an input of 680,000 B.t.u. per hour was desired. The burner described was designed to meet these conditions of temperature and heat input. It provided for three streams of entering gases: (1) A primary air-fuel mixture too rich to be combustible, that is, above the upper flammable limit; (2) secondary air for combustion of the primary mixture; and (3) tertiary air, principally for cooling the combustion products to the temperatures desired for process operation. Downward combustion of the primary and secondary streams occurred in a flame stabilized on an annular port, while tertiary air flowed in an annular path surrounding the port and also through an axial channel whose wall formed the inner ring of the annular port. This burner performed beyond the designed heat-input rates while producing stable flames, which were adjusted readily to the temperatures desired. Gas-stream temperatures were easily controlled to within 15° F. of the desired value by simple manual adjustment of the flow valves.

Jan 1, 1959

By D. S. Burgess

An investigation of the hazard of spillage of liquefied natural gas (LNG) onto water is described. About 2,000 gallons of LNG were consumed in various tests. The initial vaporization rate of LNG following spillage was found to be 0.037 lb/ft2 sec; when the spill was confined, this vaporization rate was moderated after about 20 seconds by the growth of an ice layer on the water surface; when the spill was unconfined, a coherent ice floe was not observed and the vaporization rate was essentially time independent. The maximum diameter (in feet) of the spreading LNG pool was found to be given by 6.25 Wo 1/3, where Wo is the weight of LNG in pounds, Downwind of a natural gas source, time-averaged methane concentrations were given in good approximation by standard air pollution equations. However, peak concentrations were as much as twentyfold higher than average, adding an additional factor to the assessment of hazard. The effect of layering by the cold vaporized natural gas was similar to the effect of a temperature inversion on normal gases in the atmosphere. Small-scale explosions were observed on pouring LNG onto a water surface; no single explanation seems pertinent to all of the incidents observed.

Jan 1, 1970

By R. F. Droullard

The Bureau of Mines has developed test facilities for use in a research program that deals with radiation hazards in mining. This report describes the radon test chamber located at the Denver Research Center and the Twilight experimental mine located near Uravan, CO.

Jan 1, 1984

By Robert L. Mentch

CADMIUM is one of the metals apparently destined to remain relatively scarce. The en tire supply of primary cadmium is recovered as a byproduct, concurrently with the treatment of ores of other metals. Development of the cadmium industry is attributed to metallurgical improvements in the zinc industry; output depends almost wholly upon zinc production. Cadmium is a metal of specialized uses where its superior performance has developed a strong, expanding demand. The supply, however, has been relatively unresponsive to price because of its byproduct nature. Cadmium's outstanding properties would assure it a manyfold greater market if more were available at lower prices.

Jan 1, 1958

By James A. Browning

Conventional flame channelling operates continuously at over 120 db --flame-drill channelling at a maximum of 95 db. The latter process was developed under this program. Individual drill holes are spaced to leave narrow rock webs. Sound and dust passing from the hole are effectively treated by a muffler and water injection.

Jan 1, 1980

By R. F. Zaffarano

Reservoir oil in the Greater Aneth area, Utah, part of the Paradox basin, was studied to detect variation in oil characteristics within the reservoir and to determine its relation to age of accumulation and fluid equilibrium. At least three subsurface oil samples were obtained from each of the four largest of five field divisions comprising a producing area of 45,000 acres. Height of the oil column in the Pennsylvanian Desert Creek zone is about 230 ft. In general, the oil characteristics were found to be uniform across the area, and averages were developed for use in engineering applications. Average saturation pressure was 1,780 psia; the oil was undersaturated at the initial reservoir pressure, 2,200 psia. Variation in saturation pressure shows a lack of complete fluid equilibrium and continuing diffusion of solution gas from the main body of the reservoir to two extensions linked by narrow arms. By assuming early accumulation, the time involved in this diffusion process was calculated to be about the same as the age of the reservoir formation. Cause of the concentration of gas in the main body is attributed to differential entrapment during accumulation of oil and gas from an exterior source.

Jan 1, 1963

By W. A. Grosh

The Piquette Mining and Milling Co, operates a zinc mine and concentrating mill in the Upper Mississippi Valley zinc-lead district near Tennyson, Wis. The principal ore mineral is zinc sulfide, which occurs in limestones and dolomites of the Decorah formation. Exploration in the district is by churn drilling from the surface. An adit at the base of the ore zone provides access to the mine. A room-and- pillar mining method with irregular pillars is used. Drilling is done with Jumbo-mounted drills. The broken ore is loaded by crawler-mounted front-end loaders into diesel-powered trucks for haulage direct to the mill.

Jan 1, 1959

Unfortunate occurrences resulting in injuries, loss of life, and destruction of property by explosion, fire, and other mishaps during shaft sinking in the past few years have focused the attention of the Bureau of Mines on the need for safety standards for such operations. Several States have some rules and regulations applicable to local conditions, and several Bureau publications (including some now out of print) cover the hazards that may be encountered in shaft sinking. Certain requirements of the Federal Mine Safety Code and Federal Coal Mine Safety Act may be applied, but there are no definite, uniform standards that will guide those desiring to sink a shaft safely and bring about uniform safety inspections.

Jan 1, 1957

By Ludwig Schmidt

This report, the second of a series, presents the results of laboratory corrosion studies which were made in connection with a one-year test on aluminum lease tanks conducted by the United States Bureau of Mines. Part I of the report contains the results of the field teats.5 The studies were made on an oil lease in a so-called "sour district," near Borger, Tag., where free hydrogen sulphide accompanied the production of oil, gas, and salt water. Steel tanks previously used on the lease had suffered severe corrosion, because steel is inherently susceptible to attack by hydrogen sulphide. Because of the high resistivity of aluminum to the action of hydrogen sulphide, it Was believed that this metal had promising possibilities as a material for the construction of lease tanks in "sour districts." The results of the one-year field teat proved that aluminum lease tanks will withstand corrosion by hydrogen sulphide, but it was found that aluminum was susceptible to attack by salt water, which was invariably present in certain portions of the tanks, and that hydrogen sulphide accelerated this salt-water corrosion in an indirect manner, as will be explained hereinafter. In order to study corrosion conditions encountered in the tanks during the test period, a laboratory was maintained at the site of the aluminum lease tanks.

Jan 1, 1931

By E. S. Shedd

Misch metal was electrowon from a treated bastnasite concentrate in a REF3-LiF-BaF2 electrolyte at 950° C. The metal was prepared and tapped from a 1,000-ampere cell, and nearly 100-percent utilization of the rare-earth oxide was achieved. Prolonged operation in a smaller cell (40 amperes) indicated that the composition of the misch metal product was reasonably constant, and no significant increase of impurities, with the exception of carbon, was noted.

Jan 1, 1970

By William H. Pomroy

Spontaneous combustion fires involving high-sulfide-content ores are a relatively infrequent yet serious safety hazard in mining. They are also the cause of lengthy mine shutdowns because they typically occur in areas of a mine where abundant fuel material is present but which are inaccessible for fire fighting. This Bureau of Mines report describes research to design, fabricate, and test in the laboratory and field a system that warns of spontaneous combustion fires in metal mines. Overall performance of the detection system was found to be satisfactory, in that the system was capable of reliably detecting low levels of combustion products believed to indicate the preflaming stage of spontaneous combustion in metal mines. Installation of similar systems in mines with a high risk of spontaneous combustion is recommended. Principal operating problems and recommended corrective actions are also discussed.

Jan 1, 1987

By K. B. Rojiani

Surface mining activities disturb large tracts of land resulting in the potential for greatly increased downstream sediment loads. The Surface Mining Control and Reclamation Act of 1977 places increased emphasis on the protection of the environment from the adverse effects of surface mining operations. Surface mining activities must be planned to minimize disturbance to the hydrologic balance, erosion and sediment contributions to receiving streams. Sediment ponds must provide a sediment storage volume equal to the accumulated sediment volume from the drainage area as determined by the Universal Soil Loss Equation (USLE) or other empirical methods established by the regulatory authority. It has thus become extremely important for the mining industry to secure more accurate estimates of potential erosion losses and sediment yield. Accurate estimates of sediment yield are required for the planning, design and successful operation of sediment control systems such as detention ponds and other alternative control structures and for evaluating the effectiveness of land management practices. The principal soil loss prediction procedure available for use is the LISLE. The USLE procedure is inadequate for use in predicting soil loss from surface mine regions for a number of reasons. These include: 1. The USLE was developed to estimate average average annual loss from agricultural soils. It cannot predict accurately soil loss for specific storm events. In surface mine regions a major portion of the soil loss occurs during the initial six months to one year of active mining. Accurate estimates of soil loss over short periods are thus required for the design of control structures. 2. The slope length and gradient factors used in the USLE were obtained from data or cropland having slopes ranging

Jan 1, 1983

By N. L. Wimmler

The Metaline mining district was examined in 1942 by Bureau of Mines engineers with the cooperation of geologists of the Federal Geological Survey. Because the demands of war production were rapidly depleting reserves in some of the older zinc-lead producing districts of the United States, it was decided that an attempt should be made to increase the proved or indicated ore reserves of the Metaline district. With this objective, certain areas to be explored by diamond drilling were selected. The Bureau of Mines began work on this program. January 15, 1943; work terminated September 8, 1945. Forty-five holes were drilled in seven areas, The holes ranged from 154 feet to 2,050 feet in length. Their combined length was 38,150 feet. Thirty-three of the holes were drilled in. the North Pend Oreille and the West Bella May areas.

Jan 1, 1949

By Henry P. Cole

A series of studies are described that identify critical health and safety skills needed by underground coal miners for coping with mine emergencies. First aid and self-rescue and escape were selected as two broad performance domains that include many subordinate skills needed for preventing, recognizing, and coping with mine emergencies. The performance domains and their objectives were used to direct the development of simulation exercises that permit miners to experience mine emergencies in the safety of a training room. The exercises are based upon research with similar simulations for the training of flight crews and medical personnel in information gathering, judgment, and decision making skills. Exercise content is drawn from actual mine accident and disaster case studies. The exercises incorporate recent principles of cognitive psychology and instructional design. Initial studies in annual refresher training classes suggest the exercises are stimulating for miners and their instructors, easy to use and read, sufficiently complex and authentic to challenge experienced miners, and useful devices for both teaching and testing critical problem solving skills required for preventing and minimizing emergencies.

Jan 1, 1988

By J. P. Coughlin

The U.S. Bureau of Mines has developed a monitoring system that acquires and analyzes data for use in determining the conditions that may precede mountain bumps in coal mines. Based on a UNIX workstation linked to an array of geophones in a working longwall operation, the system captures complete waveforms of microseismic events and simultaneously obtains continuous samples of the voltage levels of each geophone. Event rates and locations are calculated and displayed in real time on the UNIX workstation, which is situated in an underground instrumentation room. These results also are transmitted from the workstation to a display computer near the longwall face. The system runs continuously and has the capability to acquire, analyze, display, and archive microseismic (transient) data and single point data, such as closure and pressure changes, simultaneously.

Jan 1, 1993

By D. K. Steele

The domestic primary copper industry generates in excess of 600 million t of mining and mineral-processing waste annually. Most of the waste poses negligible environmental threat, but a small fraction, because of toxic or corrosive characteristics, may be subject to regulation under Subtitle C of the Resource Conservation and Recovery Act (RCRA) or other pertinent regulations. Among the wastes generated by various copper producers are flue dusts, slags, refinery-bleed solutions, and. acid-plant wastes. The U.S. Bureau of Mines (USBM) has researched methods to mitigate the environmental threat posed by copper-processing wastes while recovering valuable metals from these materials. Acid-leach processing of flue dusts has been demonstrated feasible along with sulfide treatment of liquid refinery wastes and acid-plant-bleed and gas-cleaning solutions to precipitate dissolved metals. In, addition, the feasibility of removing copper and molybdenum from slag, as well as stabilization of precipitated sulfide wastes by vitrification, have been investigated.

Jan 1, 2010

By R. E. Brewer

Published investigations show that many different chemical reagents have been used in determining the constitution of coals , but only a few studies have been applied directly in evaluating the effects of such reagents on the carbonization products of coal , Most of the treatments have been so drastic that any permissible conclusions that may be drawn are inferential in respect to any favorable effects on the yields and composition of the usual carbonization products .

Sep 1, 1943

By Oliver Bowles

The use of fire as a source of heat was the first step from primitive existence toward modern civilization, and heat has performed functions of inestimable importance throughout the ensuing ages. The first commercial steam engine invented in 1698 demonstrated that heat was an important source of power, and heat has since become the motivating force for railroad trains and steamboats as well as for machines in multitudes of factories. Aside from its function of supplying power, heat is an agent of vast importance in chemical reactions and engineering processes. Because of the high temperature of steam under pressure, losses by radiation from boilers and pipes become excessive unless the radiating surfaces are covered with insulating materials. Insulation is important also for hot-water pipes and many other types of equipment from which heat may radiate. Radiation losses from heated surfaces increase rapidly

Jan 1, 1943

By J. B. Gayle

Many investigators have reported studies of size distributions for particulate solids ; usually , these have involved the fitting of size distribution data to a particular mathematical function . Such studies are of unquestioned value and have contributed much worthwhile information regarding the breakage mechanisms for a variety of brittle materials . In connection with a Bureau of Mines study of the size distribution of coke , which has been subjected to the standard American Society for Testing Materials (ASTM) tumbler test , attention was focused on the relation between the 1 -inch tumbler index (usually considered to be indicative of the ability of coke to resist degradation by impact ) and the 1 /4 - inch tumbler index ( indicative of the ability to resist degradation by abrasion ) . Specifically , it was noted that for certain sets of data the correlation coefficients denoting the relation between these indexes were positive ; for other sets of data , these coefficients were negative . Preliminary consideration of this problem indicated that the usual interpretation placed on correlation coefficients was erroneous in this particular instance because the variables being correlated were necessarily related . The work described in this report was undertaken to clarify the interpretation of results of correlation studies for variables of this type .

Jul 1, 1960

By D. J. Bauer

The Bureau of Mines demonstrated the feasibility of fractionating lanthanide nitrates with a tertiary amine on lanthanum-cerium and thulium-ytterbium pairs. Optimum values were determined for pH, phase concentration, and percent chelation of metal ions in the aqueous phase. Percent extraction is markedly dependent on the concentration of lithium nitrate in the aqueous phase. Selective masking of the heavier element in each extraction system with DTPA or EDTA aqueous-phase chelating agents resulted in lanthanum-cerium separation factors of 8.5 and thulium-ytterbium separation factors of 3.4.

Jan 1, 1966