Search Documents

By G. E. McElroy

When mechanical ventilation is to supersede the natural ventilation of a mine it is desirable to determine what resistance the mine as a whole offers to the flow of air in order to specify properly the limiting duties of a ventilating fan. The relation of pressure to volume of flow for the mine as a whole may be calculated from experimental data, or it may be determined directly by measurements of volume of flow and the natural draft pressures causing flow; but in both methods the determinations are affected by many variables. With the intention of making a practical application of both methods, a small metal mine in process of development at Butte, Mont., was selected by the writers as the object of experiments planned to compare the mine resistances determined by measurements of natural draft and volume of flow with those calculated from experimental data. Four sets of teats were made with natural draft in October, 1925, December, 1925, April, .1926, and September to December, 1926; the last set consisted of a series of weekly observations. DESCRIPTION OF MINE The mine selected for the experiments was a typical vertical shaft metal mine in the development stage. No stoping had been done, and ventilation was confined to shafts, crosscuts, drifts, and raises. Figure 1 is a dia¬grammatic sketch of the main openings. All were timbered with full sets on approximately 5-foot centers. The shaft compartments were 4 by 4.5 feet, and one in each shaft was partly blocked by staggered manway landings. A pump column in the upcast shaft was discharging about 280 gallons a minute of water at 70° F. from the 1,000-foot level. The drifts were slightly sinuous, but the crosscuts were exceptionally straight and uniform in area; both drifts and crosscuts were about 5 by 7 feet in cross section. The raises were composed of vertical sections joined by frequent 450 offsets; each had three 4.5 by 4.5-foot compartments, of which two were plank-lined ore chutes and one was partly

Jan 1, 1928

By Robert Lee Stahl

Comprehensive field tests were made by the Federal Bureau of Hines at the Conda open pit mine near Soda Springs, Idaho, to determine whether surface geophysical techniques could be used to detect and delineate faults in phosphate deposits. The tests included seismic refraction, magnetometry, electrical resistivity, and airborne photography. Of the several geophysical techniques tested in the field, horizontal resistivity profiling was the most effective method for diagnosing faults. The method is quick, inexpensive, accurate, and can be easily used by mining company personnel to detect and delineate faults.

Jan 1, 1975

By James R. Boyle

The mining methods and practices used at the Young zinc mine, American Zinc Co. of Tennessee, have resulted in a low-cost, high-yield operation. Zinc ore (sphalerite) occurs in limestone-dolomite beds of the Kingsport Formation and is mined by modified room and pillar method. Utilizing trackless mining equipment which incorporates a high degree of flexibility, this operation has had a steady increase in productivity.

Jan 1, 1965

By H. D. Jacobs

A process for recovering both iron and manganese from four manganiferous ores of the Cuyuna Range was evaluated. It comprised: (1) Low-temperature gaseous reduction to convert nonmagnetic iron minerals to magnetite and manganic minerals to manganous oxide, (2) acid leaching to extract manganese, and (3) magnetic separation to reclaim iron from the leach residue. Iron recoveries from the magnetic products ranged from 70 percent to 90 percent; manganese recoveries from leach filtrates ranged from 75 percent to 95 percent. Two ores, from the Hillcrest and South Alstead properties, yielded magnetic products considered adequate for use as blast furnace feed. Although good yields of manganese were attained on all ores, appreciable iron accompanied the manganese into solution. Previous work, however, has shown that this iron can be precipitated almost quantitatively under autoclave oxygen pressure with very little loss of manganese.

Jan 1, 1970

By E. G. Davis

The Bureau of Mines made laboratory-scale experiments to examine the technical possibilities of reclaiming manganese from slags produced by oxygen lancing of high-manganese pig iron. Ferromanganese was added to molten pig iron to yield a 4-to 5-percent manganese hot metal, which simulated a product obtainable from the blast furnace. This was injected with oxygen to reduce the metal to 1 percent or less manganese and form a slag containing about 40 percent manganese. The molten slag was water-quenched, treated with H2SO4) roasted at 660° C, and water-leached to give soluble manganese and iron sulfates. The sulfates were precipitated as hydroxides, converted to the oxide form, and smelted to produce a standard ferromanganese containing 74.6 percent Mn and 0.01 percent P. As an alternate method of manganese recovery, a manganese cell feed was prepared from the leach solutions and electrolytic manganese was produced. Direct smelting of the high-manganese slag resulted in 74.2 ferromanganese meeting ASTM specifications except for phosphorus content. The high phosphorus content of the metal and high slag-to-metal ratio obtained made this approach unattractive.

Jan 1, 1966

By John Ward Smith

The Bureau of Mines drilled Wyoming Corehole No. 1 in Sweetwater County, Wyo., to sample Green River Formation oil shale. Core obtained was assayed for oil yield to determine richness and stratigraphic distribution of oil shale in the deposit. Oil shale in place at Wyoming No. 1 site represents over 200 million barrels of oil per square mile. Additional data useful in evaluating the deposit, including generalized stratigraphy and mineralogy, detailed lithologic descriptions of the core, rock specific gravity, and bore-hole logs, are presented with the oil-yield data. The sampled Wyoming oil shale resembles Mahogany-zone oil shale in rock properties and gross mineralogy. A statistically derived equation relating shale density to oil yield for the Wyoming deposit compares with a similar relationship valid for the better known Mahogany-zone oil shales in Colorado and Utah. A density log from Wyoming Corehole No. 1 is calibrated for direct oil-yield logging. The alternating rich and lean beds of shale at this site may permit creating the permeability necessary for direct production of shale oil from the shale in place.

Jan 1, 1968

Objective To develop and evaluate the effectiveness of safety training tools specific to the underground hard-rock mining industry. Background Scaling, the removal of loose rock from the roofs and walls of a mine by manual or mechanized means, may be necessary during any stage of mining. Manual scaling is very labor intensive, and mechanical methods can be too powerful and actually produce a less stable roof.

Jan 1, 2001

By D. A. Paice

Direct current electrical systems are used in most coal mines primarily to power the main haulage trains and secondarily to feed other equipment and passageway lighting. Electrical power is supplied from rotary machines or static rectifier equipment and is distributed through the mine by open trolley wires and feeder cables. The rails of the haulageway are used as a current return path. This exposed power distribution system is very vulnerable to conditions which lead to undesired leakage currents and short circuits and, consequently, the possibility of fires or other hazards to personnel. Present techniques and equipment have been utilized in so far as practical to improve the safety of the dc electrical system; however, there still appears a need for further improvement. Because of this need, this program was sponsored by the Bureau of Mines to investigate two specific technical areas related to improvement of dc electrical system safety. One area included the determination of the characteristics of mine electrical systems and their protection requirements and the verification of the adequacy of available protective devices for mine service. Despite the widespread application of industrial protective equipment in mines, there was little detailed technical information available related specifically to the performance of this equipment in service. Our task was not only to develop useful information regarding mine system protection, but also to define and verify the adequacy of the protective devices available. The second area of investigation called for development of a practical technique for detecting low level electrical fault or leakage currents. Conventional protective devices

Jan 1, 2012

By D. S. Burgess

A commercially available Halon 1301 extinguisher has been evaluated as part of an explosion-suppression system for use in coal mines. Studies were made both of the dispersion pattern of the Halon 1301 at an initial pressure of 280 psig, and of the efficacy of this suppressant against 9.5 percent methane-air flames. These flames were quenched successfully only when the suppressant was applied before the fireball diameter exceeded 18 inches.

Jan 1, 1971

By William S. Roberts

The Bureau of Mines has initiated a program to determine the availability of land for mineral exploration and development in Alaska. Researchers involved in this pro-gram are comparing land availability, based on ownership and government policies and regulations, to the distribution of known mineral deposits and terranes. This report on southeastern Alaska presents the findings of the first of six regional studies that will cover the State. The study consisted largely of data compilation and analysis using various mapping techniques. Summary land availability data are presented on copies of U.S. Geological Survey (USGS) quadrangles at a scale of 1:500,000. Five categories of land availability were identified: open to mineral exploration and development (approximately 9.4 million acres, or 38% of the 24.8-million-acre study area), open but with possible use restrictions (4.2 million acres, or 17%), selected (0.5 million acres, or 2%), patented (0.74 million acres, or 3%), and formally closed to mineral exploration and development (10 million acres, or 40%). Of the 1,187 known mineral deposits in the study area, approximately 38% are on land in the open category. Mineral terranes comprise approximately 6.7 million acres, or 27% of southeastern Alaska. Approximately 34% of these terranes are on open land.

Jan 1, 1985

By d&apos, Dennis V. Andrea

The Bureau of Mines and El Paso Mining and Milling Co. conducted a cooperative in situ leaching research program at the Emerald Isle mine near Kingman, Ariz. The objective of this research was to develop in situ leaching methods for 200,000 tons of ore exposed in the pit bottom and also 3,000,000 tons of ore under 200 feet of overburden adjacent to the pit. The research included core drilling for fragmentation analysis, inplace permeability testing, seismic surveys, blasting tests, blast vibration measurements, inplace leaching, and ground water monitoring. A l5,000-ton test area in the pit bottom was blasted and leached inplace for 117 days. This successful test was followed by leaching 100,000 additional tons of unblasted pit bottom ore. Two test blasts, under 205 feet of overburden and extending to 290 feet, were detonated in an area near the open pit. The second blast was detonated because the first blast did not create adequate permeability for leaching. Pit bottom leaching was discontinued and the test area under 200 feet of overburden was not leached because the company terminated operations at the Emerald Isle mine. Based on the research completed, an expanded in situ leaching system was designed, but not implemented, to recover copper from a 1,500,000-ton area at the Emerald Isle mine.

Jan 1, 1977

By A. J. Forney

Recent experiments used catalysts of plate assemblies in synthesizing high-Btu gas and gasoline indirectly from coal. A gas with a heating value of 925 to 943 Bt-: per cubic foot has been prod u la the hot-gas-recycle pilot plant from synthesis gas (3H2+100) with lathe turnings used as catalyst in the first reactor, and assemblies of parallel sprayed plats of nickel in the second. Solid plates made of Raney nickel, and steel and aluminum plates sprayed with Raney nickel or nickel oxide were tested. Those catalysts had very low resistance to gas flow; 90 percent lower than nickel granules used in previous experiments. In a single stage of synthesis thee nickel plates were only partially successful. Although the heating values of the product gas ranged from 856 to 941 Btu per cubic foot, the carbon monoxide content of he gas was above 0.1 percent. Both steel and wrought turnings were tested in single-stage synthesis, but the conversion of hydrogen and carbon monoxide was too low to attain the desired heating value of 900 Btu per cubic foot in the product gas. Assemblies of plates thermally sprayed with fusel iron were tried in an experiment to make gasoline. A gasoline yield of 52 percent (of the hydro¬carbons produced) was obtained using a 1H2-10O feed These sprayed assemblies were in service for 1,500 hours, the longest that this type of catalyst has been used. When a second reactor containing Raney nickel catalyst was added in series with the first reactor, complete utilization of the feed gas was obtained because in addition to the liquid product, a high-Btu gas with a heating value of 800 Btu per cubic foot was made.

Jan 1, 1965

By L. B. Pankratz

The Bureau of Mines measured heat capacities of alpha and beta spodumene (LiAlSi2O5) and of beta eucryptite (LiAlSiO4) over the temperature range 51° to 298° K. The entropies at 298° K were found to be 30.9 ± 0.2 cal/deg mole for alpha spodumene, 36.9 ± 0.3 cal/deg mole for beta spodumene, and 24.8±0.2 cal/deg mole for beta eucryptite. High-temperature heat content measurements above 298° K were conducted for the same compounds. Measurements were made to 1,150° K for alpha spodumene, 1,600° K for beta spodumene, and 1,470° K for beta eucryptite. Tables of heats and free energies of formation are given from the elements and from the constituent oxides.

Jan 1, 1967

By L. C. IlsLey

In January, 1922, a conference relative to trailing cables for use with permissible mining machines was held at the Pittsburgh Experiment Station of the U. S. Bureau of Mines. At this conference it was recommended that the bureau take steps to investigate the rubber-sheathed type of cables and to bring about the establishment of a list of approved cables. Effective until such time as a complete investigation could be made, the bureau asked the several manufacturers holding approvals for mining machines to recommend cables for use with their machines. In general the cables recommended were tentatively approved. Due to the lack of available personnel, no actual tests of cables were made until mid-1927. Meanwhile a field investigation of trailing cables was made at 20 mines of three coal companies in western Pennsylvania, and samples of cables were obtained from the manufacturers for laboratory tests. Twenty-five samples of the concentric-type cable, representing the product of five manufacturers, were obtained for the tests. These cables were of four sizes, as follows: 3 cables of No. 2 B & S gage, 17 cables of No. 3 B & S gage, 3 cables of No. 4 B & S gage, and 2 cables of No. 6 B & S gage.

Jan 1, 1929

By Susan E. Brink

The first step in determining whether Mn can be recovered by in situ leaching is to develop and test a selective lixiviant. Two column leach tests and one core leach test Were conducted by the U.S. Bureau of Mines on Mn oxide ore using aqueous sulfur dioxide (SO2) as the lixiviant. The column tests showed that aqueous S02 could selectively dissolve available Mn oxides from calcite-rich ore in a heap leach system. However, the core test showed that calcite gangue side reactions can have pronounced negative effects on the likelihood of successful in situ leaching of a calcite-rich ore with aqueous S02. Petrographic and geochemical analyses showed that both Mn (IV, III) oxides and calcite were dissolved. The abundance of dissolved Ca caused precipitation of gypsum. Acid consumption by calcite dissolution caused a rise in pH that caused the SO/S species to shift to S032-(sulfIte), which hindered reductive dissolution of Mn oxide. Gypsum precipitation did not affect complete leaching of the rock fragments in the column tests; however, it plugged the natural permeability in the core. Manganese recoveries were high for the column tests and low for the core test.

Jan 1, 2010

By Gary E. Sherman

The Bureau of Mines estimated the remaining lode gold endowment of eight mining districts in Alaska using historic production data. A log-arithmic model of cumulative tonnage of ore processed versus cumulative grade was applied to the following districts: Chichagof, Fairbanks, Homer, Hope-Seward, Juneau, Ketchikan, Prince William Sound, and Willow Creek. To assess the remaining endowment, a computerized production data base was compiled from Bureau records. These data were aggregated in 5-yr intervals for each district. Data were sorted in order of declining grade, and log cumulative grade was plotted against log cumulative tonnage. Linear regression was performed on the data for each district. The linear equation for each curve was used to predict remaining endowment at a limiting mining grade. Based on conservative extrapolation of the grade-tonnage curves, a substantial total endowment of 8,415,100 tr oz of gold remains in the eight districts. The districts with the greatest remaining endowment are the Juneau, Chichagof, Fairbanks, and Willow Creek Districts.

Jan 1, 1987

By John J. Sammarco

Illumination plays a critical role in an underground miner?s safety because miners depend most heavily on visual cues to recognize hazards. Mobile mining machinery, located in the miner?s peripheral field-of-view (±10° to about ±60° off-axis), may pose potential pinning and striking hazards. The main objective of this research was to determine if there were peripheral visual performance improvements for the detection of moving objects when using cool-white light-emitting diode (LED) cap lamps as compared to incandescent (INC) light bulbs commonly used in miner cap lamps. The cap lamp variable of interest is the spectral power distribution (SPD); the illuminances were normalized by a diffusion filter. The second objective was to determine if age is a factor for peripheral visual performance. This is important because the workforce is aging ? the average miner age is about 43 years old. Thirty subjects participated in the study; ten subjects each in the age groups of younger (18 to 25 years), middle (40 to 50 years), and older (50+ years). Visual performance was quantified by the subjects? speed and accuracy of response to detect the rotation of high-contrast (white) circular targets located 3.83 meters (m) away at -20°, 40°, and 50° off-axis. The speed of detection and the number of missed target rotations (accuracy) were measured. The prototype LED cap lamp results were best with a 11% to 15% improvement compared to the INC and LED cap lamps respectively. Age does appear to be a significant factor. For the middle and older age groups?, target movement detection time increased 75% and 60% and the number of missed targets increased 500% and 450% respectively in comparison to the youngest age group. The results also suggest that target location is a significant factor. The subjects? target movement detection time for the 40° and 50° target movements increased 16% and 69% respectively as compared to the -20° target.

Jan 1, 2008

By Kenneth M. Earl

This report describes the results of a field study conducted by the Bureau of Mines during 1956 and 1957 on manganese-and iron-bearing mineral deposits in the southern district of Aroostook County, Maine. The work was undertaken to determine the extent of deposits largely concealed under glacial drift and to obtain subsurface samples for manganese mineral identification and research in ore dressing and extractive metallurgy. The investigation was confined to the Westford Hill-Daggett Hill area in Hodgdon Township and to the Stewart prospects and vicinity in Linneus Township. Over 50 magnetic anomalies were mapped by magnetometric surveys in the Westford Hill-Daggett Hill area, Hodgdon Township. The largest anomaly, as outlined by the 1,000-gamma contour, indicates a deposit 3,200 feet long with a maximum width of 350 feet. The smallest anomaly measures about 10 feet wide by 25 feet long.

Jan 1, 1962

By R. C. Corey

GERMANIUM is an element that has come into widespread use in the electronics industry in recent, years. So far this increasing demand has been, met by ample supply: however, the future balance is uncertain, and the need has been recognized to discover additional domestic sources of germanium. This investigation was conducted to study the possibility of obtaining a potential supply of germanium from coal or coal ash. It has been known for some time that coal contains germanium; the discovery that By ash from coal-fired boilers often contains appreciably more germanium than the original coal suggested the possibility that coal ash might be an abundant and economical source of this element. In this study the concentration of germanium was determined in numerous samples of coal and ash. A number of miscellaneous waste materials also were examined in the course of the investigation; the results are reported as a matter of general interest. The methods and equipment employed are discussed in detail. Sample-preparation and analytical techniques are described in the appendix. Spectrographic analyses were made on a total of 639 samples, including coal, coal ash, slap ash from lignite and peat, wood ash, and various inorganic materials. Qualitative analyses were run on all samples, and quantitative determinations were made on those samples that contained enough germanium to be measured by this method The lower limit at which germanium can be determined quantitatively by spectrographic analysis is 50 parts per million (p. p. m.), but concentrations of less than 20 p. p. m. can be detected qualitatively.

Jan 1, 1959

By K. E. Tame

An alkaline leaching procedure for recovering uranium from a submarginal 0.1 percent Ug Og calcareous carnotite ore from the Shiprock , N. Mex . , area was investigated . A recovery of 72 percent of the uranium was attained in a preliminary test embodying the commonly accepted practice of ( 1 ) alkaline leaching at 90° C , ( 2 ) multiple stage filtration and washing for recovery of a clear pregnant solution , and ( 3 ) caustic precipitation of uranium as sodium diuranate , with recycle of the barren solution to the leaching and washing circuits . Ion exchange resins were used in a second , less orthodox test that comprised ( 1 ) sodium carbonate leaching of minus 10- mesh ore at 90 ° C to dissolve the uranium , ( 2 ) filtration to recover the leaching reagent for reuse , (3 ) recovery of the uranium- bearing solution in the filter cake as a pregnant slime slurry by repulping of the filter cake followed by a sand- slime separation and countercurrent decantation (CCD ) washing for rejection of the sand fraction , (4 ) recovery of the dissolved uranium from the pregnant slime slurry by resin- in- pulp (RIP ) , ( 5 ) elution of the uranium from the resin with a solution of ammonium chloride acidified with hydrochloric acid , and (6 ) precipitation of the uranium with ammonia gas . About 83 percent of the uranium was extracted from the ore and 95.5 percent of the dissolved uranium recovered by ion exchange . Improved laboratory results were obtained using the RIP process , but larger scale tests would be necessary for economic evaluation of the two processes .

Jan 1, 1964