Search Documents

By A. C. Fieldner

The past full year of war has increased greatly the demand for virtually all kinds of fuel, and the Bureau of Mines research and service facilities have been extended to meet these unprecedented requirements. Liquid fuels, such as aviation and motor gasolines, are fundamental to modern warfare. Bituminous coal and anthracite are needed, not only to servo the expanded industrial program for which coal normally is used but also to replace natural gas, wherever possible, and fuel oil in the Eastern States, New England, and the Pacific Northwest. Railroad transportation with energy derived from coal is replacing much of the motor-vehicle transportation that has been stopped or curtailed to conserve rubber. Pulverized coal hoe been sound to be a satisfactory and cheaper substitute for fuel oil in metallurgical heating furnaces. Celloidal fuel - a mixture of coal dust and oil - may offer a partial substitution for curtain coal-burning equipment. Several industrial experiments have been made with this type of fuel. The expansion of the steel industry in connection with the war program has required a corresponding increase in the production of metallurgical coke and its associated byproducts - light oil, tar, ammonium sulfate, and surplus gas. If the war is of long duration and new reserves of petroleum are not discovered, wartime trends from fuel oil to coal probably will not be reversed.

Jan 1, 1945

By Donald W. Mitchell

Studies were made in the Bureau of Mines Experimental coal mine to evaluate the effectiveness of a few extinguishing agents and techniques for controlling a fire on a simulated mining machine. The investigation showed that water containing an alkali-metal salt or a surface-active (wetting) agent was more effective than water alone. For close attack, fog applications was the most effective technique studied; high rates of agent application controlled the fire more quickly than low rates. The ability to control the fire increased as the distance of attack decreased. Dry powders controlled the fire when applied by shovel but not when applied airborne by rock-dust distributor or by hand fire extinguishers. Dry alkali-metal salt powders (potassium and sodium bicarbonates and sodium tetraborate) quenched the fire more readily than limestone dust. In each instance the finer powder, the greater its effectiveness. In an open ventilated entry, smoke and hot gases backed against the air currents. An airspeed of 230 feet per minute was required to permit approach to within 10 feet of the fire. At lower airspeeds, approach could be made by extending the brattice across the bottom two-thirds of the entry, by pushing the smoke ahead with water sprays, or by discharging dust from a rock-dust distributor. In a dead-end entry, the fire was approached to within 30 feet by coursing fresh air along an airtight line brattice; however, it was safer, easier, and less time-consuming to attack the fire from a fresh-air base 100 feet away with a solid stream or by high-expansion foam; the latter method was more effective.

Jan 1, 1961

By S. L. Windes

This report presents physical and petrographic properties of approximately 60 types of rock from operating mines or mineral-investigation projects and supplements Repot of Investigations 4459, Physical Properties of Mine Rock (hereinafter referred to as Part I). The physical properties evaluated include the following: Apparent specific gravity Apparent porosity Compressive strength Flexural strength (modulus of rupture) Impact touchiness Abrasion hardness Scleroscope hardness Modulus of elasticity (Yourg?s modulus) Modulus of rigidity Specific damping capacity Longitudinal bar velocity

Jan 1, 1950

By C. A. Geffen-Fowler

This report, sponsored by the Bureau of Mines, presents the results of an examination of the safety of the Blind Shaft Borer (BSB) shaft sinking system and an alternative modified BSB design concept in comparison to conventional shaft sinking technology. Detailed study of the two systems was also performed to identify and recommend design changes for optimum safety conditions. A comparison of the BSB systems with conventional shaft sinking was made on the basis of relative risk levels. Risk incorporates both the frequency and the potential consequence of accidents. A safety evaluation of the component operations of the two BSB systems was performed using a Failure Modes and Effects Analysis (FMEA) methodology. The results of this analysis show generally that both BSB systems are safer than conventional shaft sinking. The potential risk of conventional shaft sinking operations could be reduced by over 30%, on the average, with the use of the original BSB system, and by an average of about 10% with the modified BSB. Design change recommendations to further improve the safety of these systems include better fire suppression systems, improved man haulage systems and more compact hydraulics. An operational safety manual was also developed for the modified BSB system.

Jan 1, 1981

By P. S. Haury

"INTRODUCTION Many ore deposits were discovered in the Wallapai Mining District, which covers the Cerbat Range in Mohave County, Ariz., during the early period of mining there from about 1865 to the 1890's. A considerable amount of production was obtained from shallow lead carbonate ores that carried considerable gold and silver.Mining was revived in 1906 and again during the First World War, and soma of the mines were deepened into the underlying sulfide zone. Substantial quantities of metal were recovered from two mines, the Golconda and the Tennessee-Schuylkill, that were, developed to depths of 1,600 and 1,400 feet, respectively. The Golconda is credited with $6,500,000 gross productions. 2/ This mine was not operated after 1917. The Tennessee-Schuylkill is still operating after a yield of about 300,000 tons of ore that averaged 4.33 percent lead and 7.74 percent zinc and contained an appreciable amount of gold and silver.Many of the old mines were reopened in 1942 or 1943 under the stimulus of premium prices for lead and zinc. A large proportion of this work was finished with loans from the Reconstruction Finance Corporation. It was believed that a good deal of lead and zinc could be recovered from the mines if a custom mill for concentration of the ores was available locally."

Aug 1, 1947

By F. L. Wideman

This paper lists resources of sulfur in Wyoming, Colorado, Utah, New Mexico, and Arizons, an area comprising approximately 522,600 square miles, Sources of sulfur occuring within the region are sulfur are, pyrite and pyritic ores, and natural gases and petroleum. Data concerning these sources are presented on a statewide basis. Some of the known deposits of sulfur ore are surficial and of fumerole origin; other deposits have resulted from oxidation of pyrite or sulfide ores of copper, lead, and zinc. The deposits are small and the sulfur is distributed erratically in them. There is a small production from some of the deposits, and the material produced is used as soil conditioner.

Jan 1, 1957

By Nirander M. Safaya

Revegetation success on surface mined lands is dependent upon the nature of the plant growth media. Soil physical and chemical properties dictate the needs for specific reclamation and subsequent management practices. Field experiments were conducted at six coal mine sites in Oliver and Mercer Counties, North Dakota to determine the subsequent effects of a single application of selected amendments on spoil and topsoils over the five year period, 1974-1978. Considerable variations in the physical and chemical properties were found in mine spoils from site to site. The texture of spoils ranged from sandy clay loamy at North Beulah I to loamy at Glenharold, and from sandy loamy at North Beulah 3 and South Beulah sites to loamy sands at the Center site. The pH of the sites ranged from 6.5 at South Beulah to 8.2 at North Beulah 3. In many cases, the pH values of mine spoils were not significantly different from the topsoils. The electrical conductivity (ECe) did not exceed 6 mmhos cm-1 at the test sites even though in other studies much higher values were recorded in the same vicinity. The spoils from Glenharold and North Beulah test sites can be classed as moderately saline, and those from Center and South Beulah as non-saline. The sodium adsorption ratios (SAR) varied from less than 1 to 32, with highest values in the spoils of North Beulah 3 followed by Glenharold; all other sites were nonsodic. Lowest SAR values (less than 1) were found in the topsoiled sites at South Beulah and Center. Spoils of North Beulah 3 test site were highly calcareous, followed by North Beulah 2 and Glenharold. Center mine spoils which were the least calcareous of the test sites, showed the calcium carbonate equivalent three times higher than that of the topsoil. The average calcium concentrations in the spoils of North Beulah 3 and South Beulah test sites were -13 and 14 me 100g -l while at North Beulah 2 and Glenharold test sites 25 and 22 me 100-1-1 were recorded, respectively. The overall magnesium concentrations ranged from an average of 4 to 16 me 100g 1. Sodium concentrations in all sites never exceeded 10 me 100g-1. Phosphorus concentrations on the average at North Beulah 1, North Beulah 2, and Center were 10.2, 4.6, and 22.2 µg g -1 spoil, respectively. Concentrations of potassium ranged from 200 ppm at South Beulah site to more than 375 pp in at the Glenharold site. High concentrations of sulfates (239-2778 µg g-1) seem to contribute to the salinity in these spoils. Chloride concentrations of spoils were low and never exceeded 40 µg g-1 spoil. Based on established critical levels of deficiency for micronutrients in agricultural soils, it seems that none of these were deficient. However, controlled environment experiments did reveal increased plant growth responses when some micronutrients were added to the mine spoils. Treatment effects were highly site specific depending on the nature of the soil/spoil characteristics and, of course, the properties of the various treatments. While slack coal amendment to the spoils at North Beulah 2 site affected significant increases in a large number of variables (both major and trace elements), amendment of the topsoils at the South Beulah test site with leonardite resulted in significant decreases in a number of variables, particularly trace elements. Spoils at Glenharold and North Beulah 3 demonstrated the fewest significant changes due to amendments. Calcium, magnesium, strontium, organic matter and nitrogen were consistently increased from site to site with the addition of lignitic materials. Other spoil/topsoil physical and chemical properties (30 variables) as affected by amendments and time are discussed.

Jan 1, 1982

By H. Reginald Hardy

This report describes the results of a research project carried out to investigate the feasibility of using transducer arrays, located on surface or in shallow boreholes, above an active coal mine to detect and locate the source of underground microseismic activity which normally occurs during mining. The initial stage of the project involves the design and development of a self-contained mobile microseismic monitoring facility capable of use in remote field locations. Following this a variety of transducers, and transducer field installation techniques were investigated to obtain optimum sensitivity and high signal-to-noise characteristics. Preliminary efforts were also undertaken to develop semi-automated techniques for analysis of microseismic field data. Using the facilities and techniques developed field studies were carried out at a number of surface locations over a central Pennsylvania coal mine operating at depths of the order of 500 feet. In particular studies were con-ducted over a previously mined development area, troubled by extensive problems of roof instability, and over two longwall panels during mining. Although many of the field studies were carried out during the development stage of the project, results in general have been most encouraging. Limited results were obtained over the development area, however excellent microseismic signals, correlating with underground strata instability, were detected over both long-wall areas, proving the general feasibility of surface monitoring techniques. More recent studies, carried out as part of a subsequent project, and utilizing modified geophone installation techniques at a third longwall site, have verified explicitly the feasibility of measuring underground microseismic activity from surface locations. Sections of typical field data are included in this report along with a brief review of the studies carried out at each of the field sites. Detailed analysis of data obtained at the second and third longwall test sites will be presented in a later report.

Jan 1, 1974

By G. W. Grove

The wearing of self-contained oxygen breathing apparatus, although relatively safe if proper precautions are taken, is dangerous if defective apparatus -is worn, if men with inadequate training, experience, and physical requirements are used, or if improper procedure is followed. This is proved by the fact that at least 26 men are known to have lost their lives while wearing-oxygen breathing apparatus since its introduction in this country about 35 years ago. Self-contained oxygen breathing apparatus, commonly called "mine rescue apparatus" and sometimes improperly referred to as "oxygen helmets," is the only equipment that can be used for respiratory protection against poisonous mine gases, regardless of concentration or against an atmosphere containing little or no oxygen.3/ Apparatus of this type was introduced in this country in 1907, and since that time it has been widely used in conducting rescue and recovery work after mine fires and explosions and in some other work. All oxygen breathing apparatus used in this country before 1918 was imported from Europe, and although this equipment provided safer, more rapid means of conducting recovery work after mine disasters, there were many mechanical deficiencies in the apparatus which resulted in the death of some of the wearers. This led to the research and experimental work by the Bureau of Mines that resulted in the development and manufacture of more reliable and efficient types of apparatus in this country.

Jan 1, 1944

For 11 years, under authorization of the Synthetic Liquid Fuels Act of April 5, 1944 (30 U.S.C. 321-325), and amendments, the Bureau of Mines has carried on an extensive research and development program to establish methods for producing oil from coal and from oil shale. This act was passed by the 78th Congress primarily because of the stress of wartime demands for liquid fuels to supply our armed forces during World War II. The act was progressively extended by the 80th and 81st Congresses, as later peace-time demand for oil and oil products continued to increase.

Jan 1, 1956

By George W. Huseman, W. D. Mcmillan

"INTRODUCTION Feldspars represent one of the most abundant groups of minerals and constitute nearly Go percent of the material contained in the igneous rocks. They are grouped in a series of related aluminum silicates with varying amounts of potash, soda, and lime. .Approximately 85 percent of the feldspar produced in the United States is used as a flux in the production of glass, pottery, enamel and sanitary ware, brick, and tile. Notwithstanding the abundance of feldspar in the earth's crust, the only deposits that are worked to any extent are the pegmatites or coarsely crystalline dikes where natural segregation of the constituents facilitates recovery of the feldspar with a minimum of free quartz, mica, tourmaline, garnet, and other iron-bearing minerals that are detrimental in most ceramic industries.Although there are three glassplants and numerous other ceramic industries in Texas, all of the feldspar used in these plants is from other States. In the Llano region of central Texas, however, there are numerous coarse pegmatite dikes consisting primarily of feldspar and quartz in ratios up to 3 to 1. One of the more important of these dikes is the Badu Hill deposit in Llano County, Tex., which was first described by Carl Chelf 4/ in 1942. Following an examination of the deposit by W. D. McMillan, engineer in charge of the Texas field office of the Bureau of Mines, in January 1946, a proposal was made to investigate the deposit by core drilling in cooperation with the Department of Ceramic Engineering, University of Texas. This report presents the results of the cooperative investigation, which was begun April 24, 1946, and completed May 17, 1946."

Jul 1, 1947

By Edward Keller

The work covered by this report was undertaken at the request of Dr. J. A. Holmes, late Director of the Bureau of Mines, to whom the writer had been recommended by C. W. Goodale and E. P. Mathewson, of Butte and Anaconda, Mont. The director's offer was accepted for the honor it conferred and for the useful results that might be promulgated by the work in the technical field covered. The investigation was facilitated by permission to visit various works and sometimes by contributions of important definite information on a given subject. It is therefore with pleasure that acknowledgment of courtesies is made to the following corporations and gentlemen: Anaconda Copper Mining Co., Raritan Copper Works, Baltimore Copper Smelting & Rolling Co., United States Refining Co., American Smelting & Refining Co., B. B. Thayer, A. C. Clark, A. L. Walker, William H. Peirce, E. A. Cappelen Smith, H. H. Alexander, F. C. Newton, S. Rolle, R. "V. Deacon, N. W. Pierce, O. C. Martin, C. N. Sappington, James K Thomson, W. G. Derby, and the assistants of the writer, K. 1V.McComas and W. L. Raup. In this report considerable space has been devoted to general and theoretical principles on the ground that under modern conditions the best results in any field of activity can be attained only with the aid of an adequate knowledge of the best theories underlying the practice. The diffusion of such knowledge in the field of sampling metallic metallurgical materials appears to have been quite insufficient, and it is felt that when the principles involved are once thoroughly comprehended their universal application will be appreciated, so that it will make no difference whether pig iron or gold bullion is offered for test. It may further be noted that a discussion of the theories underlying practical methods is placed under the caption "Practical Sampling," with the idea that no one can be a practical sampler unless he is capable of analyzing his methods. No attempt has been made to advocate anyone method, but it is hoped that the analyses of all of the methods in use will show where each may be correctly and safely applied. The fact that it is possible to demonstrate the theoretical correctness of several methods indicates the invalidity of the claim that any single one of them is the standard.

Jan 1, 1916

By W. F. Watts

This report describes a statistical analysis of 41,502 respirable quartz dust samples collected from 1974 through 1981 in metal and nonmetal mines and mills. The goal of this Bureau of Mines study was to identify commodities and occupations associated with high quartz dust exposure so that future enforcement and research activity can be focused on the high-exposure areas. For this analysis, the Bureau used its computerized Mine Inspection Data Analysis System (MIDAS), which contains data on nearly 350,000 air samples, including data for 61 contaminants in 45 commodities. The samples analyzed were collected by inspectors of the Mine Safety and Health Administration (MS HA). The data were entered into the MIDAS computer and coded according to commodity, occupation, location, and other categorical information. Occupations an. commodities with high quartz dust exposure were identified by grouping the data by code categories. Workers at sandstone, clay and shale, and miscellaneous nonmetallic mineral mills had the highest quartz dust exposures. Within these mills, occupations with high exposures were baggers, general laborers, and persons involved in crushing, grinding, and sizing operations. Dust concentrations in these mills were not necessarily the highest, but because the dust contained a high percentage of quartz, the health risk from dust exposure was the greatest.

Jan 1, 1984

By S. H. Ash

THIS REPORT covers the third in a series of five projects into which the Conowingo tunnel system has been divided for geographical and practical reasons. It outlines the work constituting Project No.3 that consists principally of the following: (a) To sink the No. 15 shaft and extend the Alden, Sugar Notch, Baltimore No.2, and Laflin shafts from their present depths to tunnel level; (b) to drive a tunnel off these shafts to connect with the western end of the tunnel in Project No.1 (Lackawanna) and to a point 1 mile south of the No. 15 shaft; (c) to construct an emergency pumping plant at the No. 15 shaft, complete with 3 centrifugal pumps of 200-cubic-foot-per-second (c. f. s.) capacity each, and a discharge-water shaft and a discharge tunnel for conducting the water from the pumping plant into the Susquehanna River; and (d) to construct a lateral tunnel 1 mile long off the main tunnel in the vicinity of the No. 15 shaft, to be known as the Wyoming lateral. The project, as outlined, is a self-contained drainage unit that will permit unwatering inundated mines and safeguarding active mines in the Wyoming Basin of the Northern field and also will handle the water in the Lackawanna Basin, thus permitting the temporary pumping plant provided in Project No.1 to be discontinued. The pumps installed in the temporary pumping plant provided in Project No.1 can then be moved to the emergency pumping plants recommended in Projects Nos. 2 and 3, to be installed as the third or standby unit.

Jan 1, 1955

By V. L. Burdick

A literature review of current uses of Mn02 in ceramic applications with suggestions for future research. Historical background, oceanographic distribution, geology, exploitation, law and politics. Uses of Mn02 in ferrites, semiconductors, catalytic processes, thermo-luminescence and photochromic materials. Select bibliography of 33 items, plus 129 references.

Jan 1, 1980

By Jos. R. Guiteras

This paper describes the operations of the St. Joe Mining & Milling Co. in Boulder County, Colo., as of June 1936. Later a brief visit was made to the mine in September 1936; information obtained at that time has also been recorded. The company operates a gold mine, the Grand Republic, in the Sugar Loaf mining district; a 100-ton flotation mill in Lefthand Canyon near Gold Hill; and a custom sampling punt, the Boulder Ore Sampling Works, at Boulder, Colo.

Jan 1, 1937

By Larry G. Stolarczyk

An underground medium frequency radio communications system has been developed and demonstrated in both coal and metal/non metal mines. The principal advantage of the system are its low cost, ease of installation and the ability to provide radio communications to any vehicle or roving miner in the underground mine. The system provides high quality radio coverage in work areas and along manways with existing "wireplant" conductors. The conductors include AC power cable, telephone cable, metal water and high pressure air pipes, etc. The measured communications range from the base station to mobile transceiver exceeded 12,500 ft without the use of repeaters. A cost/benefit analysis shows that the initial cost of the equipment can be returned 2-6 times in the first year. The mine productivity increases by approx. 13 percent.

By David R. Wilburn

The U.S. Bureau of Mines investigated the resources, costs, capacities, market relationships, and short-and long-term supply of bauxite, alumina, and aluminum. The 45 evaluated mines and deposits in 14 market economy countries (MEC's) have a demonstrated resource of 8.4 billion mt of bauxite and an aluminum content of approximately 2.1 billion mt. Developed world bauxite resources and existing primary aluminum smelting and refining capacity are sufficient to satisfy demand through at least 1995, when additional properties (with higher cost levels) would need to be developed to satisfy future demand levels. It is anticipated that new alumina or aluminum production most likely would occur in developing regions with large bauxite potential, low-cost energy sources, and a close proximity to refining and/or smelting capacity. An increase in aluminum recycling capacity would help meet future demand increases. A series of network model supply analyses was performed for the period 1988 through 2000. Based on announced future production levels and assuming demand grows at the level outlined in the analyses, model results indicate there is sufficient material available to meet demand until 1998, where-upon an aluminum shortfall is projected. Additional analyses investigated the effect of a reduced growth rate of demand and regional production variations in Venezuela on the international aluminum industry.

Jan 1, 1993

By Raja V. Rarnani, Robert L. Frantz

More than 100 scientists from diverse professional backgrounds have contributed their expertise to the Dust Center as investigators. Approximately 50 researchers served as principal investigators, with responsibility for directing the work on Center projects, from experimental design and implementation in mines and in laboratories to coordination of efforts within the research infrastructure of the Center. The professional biographies which follow demonstrate the breadth and depth of research capabilities brought to the Center by its principal investigators.

Jan 1, 1995

THIS bulletin presents all analytical and lest methods regularly used by Bureau of Mines laboratories for characterizing coal and coke. To provide better service to coal producers and consumers, the scope of this bulletin has been expanded to include important test methods used to evaluate coal properties for commercial processing. The methods described will prove valuable to all persons interested in analyzing and testing coal and coke.

Jan 1, 1967