Search Documents

By Rudy J. Matetic

The National Institute for Occupational Safety and Health (NIOSH) at the Pittsburgh Research Laboratory (PRL) is conducting research to reduce the noise exposures of roof bolting machine operators and to prevent additional cases of Noise Induced Hearing Loss (NIHL) thru the development of engineering noise controls. This paper describes and evaluates an engineering noise control for the roof bolting machine, namely the collapsible drill steel enclosure. The results of the evaluation demonstrated that using the collapsible drill steel enclosure provided a 7 dB(A) reduction in sound pressure level at the operator?s position of a roof bolting machine.

Jan 1, 2008

By John R. Rhodes

The objective of this project was to investigate the feasibility of analytical techniques potentially capable of determination of Mg, Al, Si, S, Ca and Fe in 1 to 2 mg samples of respirable coal mine dust, in a total analysis time of not more than 10 minutes per sample, using equipment capable of being truck mounted for field-laboratory operation. It was not essential that the technique be non-destructive, but the chosen technique is, and this enables the analysis to be performed directly on the 37 mm diameter membrane filter on which the respirable dust sample is normally collected. The sensitivity requirements are therefore quoted in terms of the units of measurement, µg/cm2. The detection limit (3o of the background criterion) should be 0.5 µg/cm2 or less. The precision should be 5% or better, at concentrations above which the detection limit is not the determining factor.

Jan 1, 1972

By T. G. Donnelly

This final report summarizes the prototype development and testing of an air curtain respirotory protective device under Bureau of Mines Contract HO122087. The air curtain respiratory protective device, as part of a miner?s hat, provides protection for the underground mining machine operator against inhalation of dangerous amounts of respirable coal dust. Major components of the air curtain respiratory protective device are: 1) a modified miner hat incorporating an air curtain jet manifold from which the protective air curtain emanates, 2) a motor blower which supplies the air for the air curtain, 3) a filter element to remove the particulate material from the air used for the air curtain, and 4) the hoses and coupling used to duct the filtered air from the motor blower to the modified miner's hat.

Jan 1, 1973

By W. W. Adams

Rock dust, as a preventive or limiting factor in explosions of gas and coal dust in bituminous-coal mines, was used in larger quantities in 1939 than in any other year except 1937 since annual figures first became available in 1930, Reports from mining companies to the Bureau of Mines revealed that 144,430,000 pounds of rock dust was applied to underground mine workings in mines that produced 126,635,677 short tons of coal during the year. This quantity of rock dust applied averaged 1.14 pounds for each ton of coal produced. Rock dusted mines were the source of 39.7 percent of the total production of bituminous coal from underground mines; 33.2 percent of the total number of underground workers were employed at rock-dusted mines, and 35.9 percent of the total number of man-hours worked underground at all bituminous-coal mines in the United States during 19719 can be accredited to mines so treated.

Jan 1, 1940

By James R. Boyle

The Bureau of Mines initiated a program to address short-and long-term objectives of wetlands restoration as a option for reclamation of lands mined for phosphate. The short-term objectives were to identify a suitable wetland test site, initiate an extensive premining monitoring plan, develop an acceptable mining plan, and recontour and revegetate the test site. These goals were accomplished using a unique combination of expertise provided by Federal and State agencies and private industry. A 6.5-ha forested wetland with an associated streambed was offered by private industry as the test site. A premining monitoring program was established and carried out from May 1982 to October 1983. A control site was established to determine ecological changes unrelated to mining. Clearing and mining began in October 1983 and was completed in April 1984. Grading and streambed restoration was completed in February 1986. Revegetation of the site was completed in February 1987. The program to meet the long-term objective of postmining monitoring is described.

Jan 1, 1988

By Phillip R. Moyle

A cobalt/manganese occurrence in Clark County, Nevada was the subject of a site-specific mineral investigation by the U.S. Bureau of Mines in 1988-90. The study site is in the northern part of the Million Hills (wilderness) study area which is administered by the Bureau of Land Management. Field work during a period of one week consisted of geological mapping and sampling of workings and outcrops, and geochemical and geophysical surveys conducted on four transects totalling 7,600 ft. Although the concentrations of cobalt (0.1 to 0.5 percent) detected in samples from the fissure zones are within the range of grades associated with world-class economic deposits, the volume of material enriched in cobalt at the study site is insufficient to warrant consideration as a potential resource. Concentrations of manganese, nickel, copper, lead, zinc, barium, and thallium, although anomalous, are too low for economic consideration. At the study site, workings consist of three trenches and nine pits. The exploration history is unknown, and no production is reported.

Jan 1, 1990

By W. W. Adams

Rock dust, as a preventive or limiting factor in explosions of gas and coal dust in bituminous-coal mines, was used in larger quantities in 1939 than in any other year except 1937 since annual figures first became available in 1930, Reports from mining companies to the Bureau of Mines revealed that 144,430,000 pounds of rock dust was applied to underground nine workings in mines that produced 126,635,677 short tons of coal during the year. This quantity of rock dust applied averaged 1.14 pounds for each ton of coal produced. Rock dusted mines were the source of 39.7 percent of the total production of bituminous coal from underground mines; 33.2 percent of the total number of underground workers were employed at rock-dusted mines, and 35.8 percent of the total number of man-hours worked underground at all bituminous-coal mines in the United States during 19719 can be accredited to mines so treated. Rock dust was employed chiefly in the larger mines, which numbered only 431 out of 6,016 underground mines in operation in 1935, according to reports from mining companies. The mines in which rock dust was used had an average of 288 underground employees per mine, whereas mines in which rock dust was not used averaged only 62 underground employees per mine.

Jan 1, 1940

By Adrian Brown

Pilot Hole ?X? was drilled to test the formations through which the ventilation shaft for the proposed U.S.B.M. demonstration oil shale mine will be drilled. Five permeability tests were performed at various stratigraphic levels within this hole. The test method used was that of pumping fluids out of the hole for three hours, using the air lift method, followed by a three-hour period where the recharge was observed. Transmissivity and permeability results were determined from these test data. The test procedure used is described and supporting data for the hydrologic tests are provided.

Jan 1, 1977

By Travis Q. Lyday

Mineral production in Fiji, a group of 322 volcanic islands and atolls of Melanesia in the southern Pacific Ocean, continued to be dominated by gold. However, the Fijian mineral sector remained a minor factor as a source of export earnings, Government revenues, and employment, generating only 1% of the gross domestic product (GDP), estimated as $1.2 billion.2 The largest and most important mining operation was the Vatukoula gold mine on the north side of Viti Levu, the main island. The Vatukoula Mine has been in prduction since 1932, producing about 3.8 million troy ounces of gold and 1.3 million troy ounces of silver to date. In April 1983, the large Australian mining firm, Western Mining Corp. (WMC), assumed operation of the mine in a joint venture with Emperor Gold Mining Co. Ltd., which operated the mine previously. The WMC takeover of the mine management was expected to bring in additional capital and technological expertise in order to modernize operations, increasing both efficiency and output. During the year, rate of recovery was only about 75% of the gold contained in the ore and only 40% of the contained silver. Mining at the Vatukoula Mine was done using bath opencut and underground methods, with about 60% of the ore mined attributed to the underground operations.

Jan 1, 1985

By Larry A. Haas

Carbonyl sulfide (COS) was decomposed to sulfur and CO in a silent electrical discharge. A threshold of about 4 kv at 60 Hz was required to dissociate the gas in a laboratory ozonizer at 790 torr with electrode gaps between 1 and 5.5 mm. Above the threshold value, the reaction rate increased with increasing voltage with helium or nitrogen diluent. With the latter diluent, higher voltages had to be applied to obtain the same yield in the 4-to 12-kv range. The COS decomposition rate increased with COS concentration, but a saturation value was reached at about 10 pct COS. The reaction rate decreased at low linear gas velocities as obtained at lower gas flows, larger electrode gaps, or larger reactor volumes. Increasing gas temperature also decreased the decomposition rate. The presence of solid adsorbents such as quartz wool, bauxite, or charcoal had no significant effect on the reaction rate. The addition of S02 did not affect the COS decomposition rate, but small amounts of water decreased the reaction rate. Over 50 pct of the COS was decomposed at room temperature and atmospheric pressure in a l7-kv ozonizer using a gas containing 0.9 pct COS in helium flowing at a rate of 0.3 liter/min. The average current was less than 5 ma. This method has possible application in eliminating the toxic air pollutant, COS, which is generated in petroleum refineries and in processes involving reactions between sulfurous and carbonaceous materials. Carbon monoxide that is formed can be further oxidized to CO2 after the collection of elemental sulfur.

Jan 1, 1972

By Suzann C. Ambrosio

Cameroon's mining industry continued to be dominated by crude petroleum. The value of petroleum output was estimated at $1 billion.2 The 1982 gross domestic product (GOP) was approximately $8.4 billion. During 1981, crude oil export revenues increased in value 30%, comprising approximately 56% of Cameroon's total export earnings. The 1982-87 5-year plan emphasized, hydrocarbon and agricultural development and targeted the exploitation of bauxite and clay deposits. New petroleum legislation was promulgated on November 26, 1982. Public Law No. 82-20 detailed hydrocarbon companies' obligations concerning oil and gas discoveries and exploitation. In general, the Cameroon Government has participated in joint ventures with private companies and has levied a 57.5% petroleum tax plus adjustable royalties. Exploration expenses were paid by concession holding companies, and the Government in the past has reimbursed 50% of expenses under certain conditions.

Jan 1, 1984

By Robert Stefanko

A series of workshops were conducted -with invited participants from the coal mining industry to identify the most pressing research and development needs of the industry. Six workshops were held on the following subjects; Research Priorities for Mining-Oriented Universities, R&D Needs-for Surface Coal Mining, R&D Needs for Deep Coal Mining, R&D Needs for Anthracite Coal Mining, R&D Needs for Coal Mine Health and Safety, and R&D Needs far Environmental Control in Coal Mining.

Jan 1, 1975

By R. A. Franks, G. F. Friel, J. C. Edwards, L. Yuan

The reversal of smoke products-of-combustion (POC) from a mine fire was determined in a mine section with the airway connectivity of an electrical Wheatstone bridge. Four diesel-fuel fire experiments with fire heat-release rates between 504 and 771 kW were conducted in the Safety Research Coal Mine (SRCM) located at the National Institute for Occupational Safety and Health’s (NIOSH) Pittsburgh Research Laboratory (PRL). Smoke reversal propagated upwind from the fire with significant leakage into the upwind diagonal airway and without causing a complete reversal of airflow in the diagonal airway. A control measure consisting of a brattice suspended half entry height from the entry roof was determined to abate the smoke rollback. Computational fluid dynamics (CFD) analysis of the smoke movement agreed with the measurements.

By William Porter

Hand scaling is a physically demanding job and is responsible for numerous overexertion injuries in mining. This experiment studied rib scaling from an elevated bucket to examine force generation capabilities and electromyographic responses to a prying subtask. Subjects exerted force using two bars (steel and fiberglass) at five target heights. Work height significantly affected peak prying force during scaling activities with highest force capacity at the lowest level (p = 0.0188). Bar type did not affect force generation (p = 0.7843): However, use of the fiberglass bar required significantly more muscle activity to achieve the same force (p < 0.05). It was concluded that miners should scale points on the rock face that are below their knees, and reposition the bucket as often as necessary to do so. Additional research is needed to fully understand the impact of bar type on the physical demands of an entire scaling task.

Jan 1, 2006

By Ren G. Dong, Dan E. Welcome

Instrumented handles or dynamometers are widely used to measure hand forces and/or the biodynamic response of hand-arm system. To study hand-transmitted vibration exposure, six generations of instrument handles were constructed or initially developed by researchers in ECTB/HELD/NIOSH. This presentation provided a summary of these handles. Their basic characteristics, limitations, and usefulness are described, which may help their appropriate applications and further improvements. Six Designs of Instrumented Handles Handle 1: The conceptual design is recommended in ISO 10819 (1996)1 for glove test. The grip force is measured by detecting bending strains on a measuring beam in the handle. A special handle fixture was designed to connect the handle to a shaker. Except the screws, the handle and fixture were made from aluminum. Handle 2: The design is based on the principle of shear strain measurement.2-3 Both grip and push forces can be measured simultaneously using this handle. This handle was directly designed for a simulated vibrating tool. Handle 3: This design is basically composed of a handle base, a measuring cap, and two charge-based sensors (Kistler 9212) sandwiched between the base and cap. The handle was also made from aluminum. The fixture for Handle 1 was also used with this handle. This generation of handle has three different handle diameters (30, 40, and 50mm).4 Handle 4: This design is an improvement from Handle 3. The handle fixture was totally redesigned and it was much stiffer than the previous one. The aluminum measuring cap was replaced with a magnesium cap. Handle 5: The basic structure of this handle is the same as that for Handle 3. However, the piezoelectric sensors were replaced with two strain gage based sensors (Interface SML-50). Handle 6: This handle includes two measuring caps, four piezoelectric sensors, and a handle centre base. The handle fixture was the same as that with Handle 4. Methods for Handle Examinations The static and dynamic characterizations were performed using the methods reported by Dong et al.5-6 Results and Discussion Handle 1: The static force measurement depended on the hand grip location on the handle. Its natural frequency was less than 200 Hz.5,6 Because the transmissibility of gloves may not vary significantly with the applied grip force, this handle may be acceptable for glove test. However, the force measurements with this handle may not be reliable. Handle 2: The static force measured with this handle was insensitive to the hand acting location. However, when the handle was vibrating, the force signals could be totally distorted. For this reason, it was not used for vibration studies.

Jan 6, 2006

By James C. Barker

The U. S. Bureau of Mines made a reconnaissance In the western Crazy Mountains for cobalt and associated metals as part of the Alaska-wide critical and strategic metals program. The area, located about 75 miles north of Fairbanks in central Alaska, is underlain by complexly faulted, predominantly clastic sedimentary rocks bordering the Tintina Fault system. Above background metal concentrations were found to occur in altered fault zones, tectonic breccias, soils, and ground water seeps and precipitates that either cut or are derived from the faulted clastic sedimentary rocks. Up to 0.115 pct cobalt and more than 2.0 pct zinc were detected in soil samples. Spring precipitates contained up to 1.3 pct zinc, 0.037 pct tungsten, and other metals. Some localities lacked cobalt but contained anomalous amounts of copper, lead, zinc, silver, and other metals. No outcropping of primary metallic minerals was located because of Colluvium and vegetation cover and extensive deep leaching. Therefore, whether the metal values encountered are due to primary deposits with economic development potential or are the results of concentration by ground water from low-grade sources is unknown. The presence of cobalt, nickel and zinc, and the identification of minor tin and tungsten indicate that further investigation is warranted.

Jan 1, 1983

By W. P. Yant

Canister-type gas masks Pave become an essential part of the equipment of many industries, not only for use in .emergencies, but also in performing normal operations of industrial processes and procedures, particularly where ventilation is not practically or economically feasible. They are also used widely for enhancing safety of operations which previous to the development of gas masks had been performed in harmful atmospheres. Since the inception of industrial gas masks the Bureau of Mines has been actively engaged in endeavoring to increase the efficiency and safety of these devices, and this bureau bas become a source of advice to manufacturers in producing devices of good quality and to industry in the proper selection and use of these devices. In order to give first-hand information and keep current with the demands and needs of industry it is necessary to perform investigations from time to time. This report deals with tests of certain types of commercial gas-mask canisters for protection against mercury vapor.

Jan 1, 1932

By E. G. Valdez

Three cryogenic systems that utilized liquid nitrogen, dry ice, and methanol with dry ice were investigated in conjunction with crushing and classifying techniques. The systems were used to aid in separating and reclaiming the metallic components contained in insulated wires, shredded automobile nonferrous metal concentrates, small motors, generators, and rubber tires. Wire strands, 2 to 6 inches long and insulated with polyvinyl chloride and neoprene, were chilled at -60° and -195° C, then roll-crushed and processed by water elutriation; this procedure resulted in two products--a sink fraction that was 99 percent metallic and a float fraction that was 99 percent nonmetallic. Excellent separation of zinc die-casting alloys from copper and aluminum contained in shredded automobile nonferrous metal concentrates was attained by chilling at -72° C for 1 minute, crushing in a grateless hammer mill, and screening. From the screened products, 97.2 and 100 percent of the copper and aluminum, respectively, were recovered in the plus Pinch fraction, and 100 percent of the zinc was recovered in the minus 1-inch fraction of over 97 percent zinc die-cast purity. Laboratory experimental results comparing direct and indirect chilling indicated that a sufficiently low temperature could be attained by indirect chilling to permit use of a liquid C02-dry ice system on insulated wires and mixed nonferrous metallic concentrates.

Jan 1, 1973

By D. Harrington

Seldom, if ever, has any mining hazard presented itself that some method has not been devised to control it to some extent; the degree of success of such control depends largely upon the intensity of desire to prevent suffering, injury, and death. The economic saving to be realized and the more definitely this is realized by all concerned, the more quickly and effectively will the hazards be handled is an important incentive to prevention of accidents. Preventing coal-mine explosions is by no means a complex problem; all that is necessary is sensible, conscientious, sustained effort. The fact that explosions can be prevented has been well-demonstrated by the record of the post few years; the average annual death toll from explosions for the 5 years 1906-1910 was 438, and for the 20 years prior to 1929 it was 265: during the past 4 years an average of only 32 deaths per year resulted from this cause, although the annual production during that time varied but slightly from that of 1906-10. This is a truly remarkable reduction, and if other types of mine accidents had been reduced in the same ratio only about 300 would be killed annually in our mines instead of the nearly &apos;1,300 killed in 1936 and the approximately 2,000 killed annually for many years. Although frequency of occurrence of explosions has not lessened greatly during the last decade, their severity decreased markedly, which would indicate that effective means are being taken to prevent the spread of explosions, even though ignitions and their causes are not being handled nearly as effectively as they might or should be handled. Several large coal-producing States, which in the past have experienced numerous disastrous explosions, have been free from such disasters for continuous periods as long as 8 years in the relatively recent past. The application of rock dust to underground surfaces has been an important factor in preventing widespread explosions; some of the mast dangerous mines have been rock-dusted fairly adequately, and this has been amply repaid in the reduced severity of explosions, as heretofore indicated; however, many have applied rock dust apparently without giving much consideration to the amount required to prevent

Jan 1, 1938

By Richard L. Fowler

[Study and development of sensing techniques and sensors were performed to aid shuttle car drivers in detecting, obstacles and in guiding the car along the face haulage route. Microwave, acoustic, and optical sensing techniques were considered as part of the feasibility study for obstacle detection. Various guidance techniques, including wire-following and rib-ranging were investigated. Active optical sensing was selected for obstacle detection to obtain the bear overage and sharp angular cutoff characteristics required within the packaging limitations defined by the shuttle car configuration. Rib-ranging guidance was selected to achieve completely self-contained shuttle car system which responds to the mine geometry without need for wires, stripes, or other path defining devices. Extensive hybrid computer simulation runs were performed to valuate various guidance techniques during the feasibility study. Subsequent simulation rues were performed to establish parameter values for the rib-ranging guidance system. The obstacle detection and guidance system was designed, fabricated and installed on a standard shuttle car. The system satisfied all applicable permissibility requirements of Schedule 2G. An experimental permit was issued to Bendix for operation in an underground coal mine. System evaluation tests were performed first above ground at the Bendix Research Laboratories. The simulation model was validated by these runs. Final testing wan performed underground in an operating mine with an experienced shuttle car driver. All sensors successfully demonstrated Chi predicted performance capability during underground face haulage tests. Dust did not Impair system performance and lens cleaning was not required during working shifts. Further development is required to achieve the desired obstacle detection performance Closed loop steering control with manual override is recommended o: mended for the lateral guidance e system. The guidance system should be an invaluable aid to low-coal shuttle car drivers where continuous mining machines are utilized.]

Jan 1, 1973