Search Documents

By Fumihiko Sumiya, Yukio Kato, Yoshikazu Hirosaki

Secluential blasting is one of the most popular methods in blasting. tiowever, it is well known that an emulsion explosive can be dead-pressed by dynamic pressure generated by the previous detonation. It is difficult to gain the expected blasting performance due to tb.e malfunction of explosive caused by deadpressing and shock desensitization. Such malfunction of an explosive is undesirable for safety blasting operation. Voids in the emulsion explosives will considerably affect the performance of explosives such as sensitivity, detonation velocity (DV), pressure-resistance and so on. To clarify the detonability and the performance of precompressed emulsion explosives, the DV was measured. Three types of microballoon or micro bubble ; two types of glass microballoon(GMB), resin microballoon@MB) and chemical gas bubble ; were used as sensitizers for the sample emulsion expiosives. The underwater explosion test was carried out to load dynamic pressure into the sample explosives. The dynamic pressure was generated by the detonation of a donor explosive, and the DV of the sample explosives as acceptor was measured by ionized gap terminals. The dynamic pressure level and initiation interval for the donor and the acceptor were chosen as experimental factors. The detonability was carefully investigated at short initiation intervals taking into consideration the interaction between same delays caused by the deviation of the ignition time of the electric detonators. From these experiments, the following results were obtained ; A) The DV of precompressed emulsion explosives was low compared with that of uncompressed emulsion explosives in all pressure conditions. B) The decrease of DV in the sample explosives sensitized by GMB s was larger than that of DV in the sample explosives sensitized by RMBs or chemical gas bubbles. C) The recovery of the detonability occurred rapidly in the sample explosives sensitized by RMBs and chemical gas bubbles. However, a long period was needed for the recovery of detonability in the sample explosives sensitized by GME! s. It was concluded that the type of microballoon and micro bubble significantly influenced the detonability of precompressed emulsion explosives.

Jan 1, 2002

By P. R. Mohanty, Kaushik Dey

Blast-induced tunnel overbreak prediction in the past has been based on peak particle velocity measured far from the blast site with necessary extrapolation. This has often resulted in suggesting higher damage threshold levels of Acceleration/PPV for overbreak prediction (Bogdanhoff, 1995, Holmberg and Persson, 1997, Murthy and Dey, 2002). These, site-specific far-field blast vibration studies, have also revealed that predicted PPV levels for overbreak could lie in the range of 700-5000 mm/s, an extremely wide range to generalize. Experimental blasts were conducted, in an underground metal mine located in eastern India, with an objective to study the level of acceleration /peak particle velocity generated in tunnel blasting. Accelerometers and tri-axial geophones with measuring ranges upto 500 g, 254 mm/s respectively, were mounted on the tunnel floor close to the blast face, with sensor distances varying from 15.25m to 36.10m. Due to straight faces the measuring distance could not be reduced further anticipating, in particular, cable damage. The equipment used was of M/s Instantel Inc., Canada. The blast pattern used was burn cut with large dia relief holes providing the required free face. The blast hole depth was 1.8m. Tunnel overbreak was measured using a telescopic offset rod fabricated at Indian School of Mines, Dhanbad, India.

Jan 1, 2004

By B Mohanty

Full-face blasting rounds have been used to excavate a 4.6-mdiameter shaft at Atomic Energy of Canada Limited's Underground Research Laboratory near Pinawa, Manitoba. Both standard pyrotechnic delay detonators and the newly developed electronic delay detonators (EDD) were used on the project. The full-face blasting technique, employing 89-mm-diameter relief holes and 38-mm diameter blast holes, NG-based explosives, and the regular long period delay detonators, has been standard practice at the site, giving excellent wall control and fragmentation results. The comparison blasts using pyrotechnic detonators and EDDs were carried out to test the operational logistics, timing accuracy and blast results obtained with the latter. The long period pyrotechnic delays ranged from O to 18, with the nominal delay varying between 350 ms and 800 ms. The EDD blasts used the same number of periods, with the respective delay interval between successive periods set precisely at 190 ms and 210 ms for the two blasts. Based on a broad range of critically assessed parameters, the EDD blast results proved to be signficantly superior to those obtained with regular pyrotechnic detonators. The results have been analyzed in detail and the relative merits of the two delay systems have been determined. Alternative designs to derive maximum benefits from EDDs in shaft and tunnel blasts have also been suggested.

Jan 1, 1990

By John L. Floyd

The use of explosive energy to displace overburden or waste material can provide substantial savings to operations which normally rely on mechanical means for material removal. To optimize the available explosive energy, it is important to quantify the rock's response to the type of explosive and explosive accessories used. During a blast, rock breakage and movement occur so rapidly that the naked eye cannot detect the details of the fragmentation process. A relatively high speed motion picture camera (500 frames per second) can provide the extended time base needed to analyze in detail the site-specific rock response to the explosive detonation. The data of importance to blast casting that can be quantified from these films includes initial face movement, trajectory of rock, and differential face velocities of the material shot. In addition, the ground swell velocities, stemming confinement, and stemming ejection velocity can be determined. The performance of explosive products and delay element accuracy can also be ascertained. The use of high speed motion picture photography and analysis can reduce the number of field trials necessary to maximize explosive performance and increase the benefit provided by blast casting, and in turn, lower production costs. This paper will discuss the methods used for data accumulation and analysis. In addition, three field studies conducted at three separate mining operations will be presented.

Jan 1, 1988

By Omer Yilmaz Erkoc, Gulsec Uyar Aldas

Blasting techniques, which have been used for a long time in Turkey, are powerful and economical tool in producing raw material in mining, quarrying, construction .etc. industries. The development of the society within the world has resulted in a substantial increase in the scale of such industrial projects. However, the expansion of such activity has been matched by an increased public awareness of environmental issues, particularly when it occurs in relatively close proximity to residential areas. One of the most troublesome issues facing the mining, quarrying and construction industries when carrying out their blasting activities is that of ground vibration. Because, blasting induced ground vibration can reach to very far distances from the source and has the potential for damage to concern to the inhabitants of property.

Jan 1, 2002

In this work, is being described the developing of the study for the demolition by controlled blasting project of a building of reinforced concrete, in the center of a spanish city. Synthetically, it is being analyzed the timing of the fall of the parts of the structure. This documentation is completed with a group of four photographs of the falling sequence and a film about several demolitions and the particular one described in this paper.

Jan 1, 1977

By Michael McDougall

"Suncor Inc. Oilsands Group, Mining Operation in Northern Alberta, Canada, has beenblasting to loosen the oilsands to increase production and decrease maintenance of the hugebucketwheel excavators for over twenty years. In 1991 an area of the mine wasencountered which had a working face in excess of 130 feet. In order to maintain theproduction objective, the blasting department took on the task of providing as much of ablasted face to work with as possible. In doing this Suncor has exceeded several knownrecords in production blasting."

Jan 1, 1993

By Jeff Wachendorf

As the title implies, this paper details the start of a cast blasting and the design flexibility required to satisfy different parameters encountered on a large coal mine employing cast blasting as the program has grown and evolved around the town of Colstrip, Montana. As strip ratios have increased, the need to adapt and find solutions to provide coal at a reasonable cost to the mine mouth power plants has risen. Colstrip, Montana has a long history of coal mining which dates back to the early 1920s when Foley Brothers began supplying coal strictly for powering locomotive engines.

Jan 1, 2015

By Shulin Nie

The dead-pressing phenomenon in emulsion explosives is wellknown. Research work on this subject has been carried out at the Swedish Detonic Research Foundation for the last few years. Several experiments with emulsion explosives under dynamic pressure condition have been carried out both in iron pipes and in blast holes in rock. The main object was to study the critical amplitude and duration of the pressure causing the explosive to be dead-pressed.

Jan 1, 1993

By B. K. Rath

The Industrialization of a country depends on its mining activities to a great extent. In mineral production, India has a top rank not only in South Asia, at the global level too. Quantum of mineral production is almost directly proportional to the quantum of explosive production. Mining sector consume more than 80% of country’s explosive production. Due to rapid growth of mining activities in the country, the explosives industry has been developing very fast in terms of quantity, quality and types. , In this paper, India’s post independent chronological date regarding use of explosives, their types, their constraints and a profile of well-known manufacturers has been meticulously presented. A production figure for three years with system analysis has been presented. The paper also deals with present consumption pattern while making a futuristic forecast. In view of the anticipated changes that are to take place in mining industries in near future, the manufacturers of explosives have to pay a vital role. The paper highlights some concrete and valuable suggestions and recommendations. Small scale Companies have to limit their production to Slurry and Emulsion types of Cartridged explosives whereas the large manufacturing units have to concentrate on Bulk explosives, specialized explosives and better initiating systems. The large manufacturing units have also to make all concerted efforts to compete with global market for significant export. The Country for its rapid growth needs basic raw materials like Coal, Iron Ore and Limestone. So, the extraction of these minerals is of prime importance. The more we produce and consume, the more will be Industrialization. The Industrial growth rate has been around 6% during the last few years. As the Industrial growth rate is moderate, there is moderate increase in mineral extraction in the Country. Additional mineral extraction demands additional explosive production (Annexure-1).

Jan 1, 2000

By Richard J. Mainiero, T S. Bajpayee

The Bureau of Mines, U.S. Department of the Interior, has developed test procedures and criteria for evaluating explosive reactivity of explosive contaminated solid waste substances generated by U.S. Army Ammunition Plants. These substances are produced as explosive-contaminated sludge from waste water treatment plants, residues from the burning of munitions and explosives on open ground, and residues from deactivation furnaces. The characterization of explosive reactivity is a prerequisite for disposal of such waste materials, which may be contaminated with primary explosives, propellants, or pyrotechnic materials. The Bureau has proposed two tests for this purpose. These tests were developed to evaluate the explosive reactivity as defined in Title 40, Code of Federal Regulations, Part 261.23(a)(6) and (7). These are Bureau of Mines Gap and Bureau of Mines Internal Ignition tests, which determine the sensitivity to shock and thermal stimuli, respectively. This paper also includes gap and internal ignition reference data for typical blasting agents, high explosives, propellants, and marginally reactive substances. These reference data were used to establish test criteria. The Bureau has evaluated over 400 samples of contaminated soil, sludge, and burning residues using these two test methods.

Jan 1, 1988

By Paul Worsey, Delbert Da, Eric Achelpohl

The University of Missouri-Rolla is currently researching the concept of using glass microspheres in explosives as taggants as part of a 3-year technical project funded by the Bureau of Alcohol, Tobacco, and Firearms. These taggants are intended to provide two functions, first explosive detection and second post explosive event identification. The key priority is being able to detect explosives used in terrorist acts prior to detonation. The research on the use of microspheres includes the development of indicator taggants for the purpose of revealing the presence of hidden explosives, by either emitting radiation when bombarded with neutrons or emitting selective vapors, such as DMNB which may be readily “sniffed”. Of secondary importance, after an illegal explosion, the tags serve to identify the lot number, etc of the explosive. This information is to aid in the tracking, arrest, conviction and imprisonment of the perpetrators.

Jan 1, 2001

By Cameron McKenzie

Flyrock is a complex issue involving interaction between the charging crew, the blast design, and the local geology, and once conditions on the shot meet certain criteria, the probability of a flyrock incident becomes unacceptably high. It is essential that flyrock awareness be built into the blast design process, requiring an engineering approach to understanding and controlling the outcomes and managing the associated risks. Based on previous studies of flyrock and published literature relating to fragment motion at high velocity in air, the equations to predict maximum flyrock range, and the size of particle achieving the maximum range, for blasts of varying rock density, hole diameter, explosive density, and state of confinement have been developed. These equations, and other associated correlations, permit the flyrock footprints to be established for any charge configuration, in any size blasthole, in rock of any density, and with particles of any known shape factor. The equations developed, and the mechanisms they reflect, allow engineers to go a long way towards understanding the primary factors controlling flyrock generation, including the rock mass, the blast design, and the quality of blast design implementation, i.e. the human factor. The paper presents guidelines as regards use of the equations to establish personnel clearance distances as a function of charge design and implementation, and equations to estimate appropriate stemming lengths when blasting must be conducted close to occupied or sensitive structures. The equations are amenable to definition of, and quantification of Flyrock Risk.

Jan 1, 2009

By Michael M. Jackson

"The mining industry has for some time compared explosive energy requirements to theresults obtained using ANFO. Drill patterns, powder factors, and explosive bulk strengthshave all been developed based on the detonation characteristics and blasting resultsexhibited by ANFO. However, there are some mining applications where the use of ANFOcan cause over_blasting if loaded to acceptable collar heights or surface breakage problemsif collar heights are reduced. A specialized, low strength, low density water gel explosivehas been developed that has loading densities in the range of 0.4 to 0.7 g/cc. The uniquecharacteristics of the low density water gel explosive is that the explosive can beformulated with a range of available bulk strengths while maintaining excellent detonationsensitivity for use in applications involving ore/waste control, restricted blast patterns,small bench heights, etc. The"

Jan 1, 1993

By Sharon K. Reamer, Klaus G. Hinzen

A series of controlled seismic experiments was performed in a limestone quarry in southern Germany to study seismic effects of cylindrical charges fired in both a half space (HS) (burden 63 m) and quarter space (QS) (burdens of 3 and 3.5 m) geometry. Charge columns contained from 20-32 kg of explosives and initiated from the bottom. The explosives formed a cylinder 4 m (20 kg) and 5 m (32 kg) high and 90 mm in diameter at depths from 3-8 m below ground level. Prior to each of the larger explosions, small charges of 0.12 kg seismogelit were fired at 4 m and 8 m depths in the same boreholes. Seismograms were obtained from 23 three component surface stations and up to 10 three component borehole stations (6 m depth). For each experiment, stations were located on three linear profiles of length 72 m at different azimuths from the source and one semicircular profile at a constant range of 30 m.

Jan 1, 1991

By John Wright

During June and July 1999 a United States Antarctic Program (USAP) team of three commercial divers and one blaster successMy removed an underwater rock obstruction which interfered with safe docking practices of research vessels that call at Palmer Station - the USAP research facility located on Anvers Island, Palmer Peninsula Area, Antarctica. Ordinarily, such a project might be considered routine. However, certain aspects of the project, particularly those dealing with logistics in a remote corner of the earth, sat3eguards for marine biota, and working underwater in the dark of the austral winter, conspired to make this project interesting. Even more challenging was ensuring the protection of the existing pier - a deeply corroded sheet pile structure backfilled with loose gravel and rock - which lay less than 50 feet away from the target obstruction, not to mention uncertainties at the outset as to the nature of the rock mass forming that obstruction.

Jan 1, 2001

By F O. Otuonye

Full-face blasts were fired in a 12 x 8 ft drift of an underground hardrock mine in a basalt formation with porphyry copper to study the effects of drill pattern and explosive type on the size distribution of the resulting muckpile. Each muckpile produced by five full-face blasts was sampled four times with a scooptram equipped with a 5-cu yd bucket and the size distribution of the broken rock in each bucket was determined by screen analysis. Results show a strong dependence of the fragment size distribution of muckpile on the blast pattern and explosive type for a given rock type. The mean fragment size of the broken rock was compared with the predictive equations of other investigators. Random sampling of the muckpile from full-scale blasts and screen analyses of the samples are recommended in assessing the size distribution of the broken rock because of scaling errors that are inherent in full-scale blasts when designed from results of small-scale tests.

Jan 1, 1985

By Janos Foldesi, Calvin J. Konya

The determination of the number of primers necessary to efficiently initiate an explosive column charge is essential to good blasting. If the number of primer is insufficient, the total energy stored in the main charge will not be released. On the other hand, the use of too many primers will be counterproductive and raise the blasting cost. Tests were conducted by the authors to determine the correct priming procedure for a basalt quarry. This paper describes the results of those tests.

Jan 1, 1976

By Callie Covert

This paper describes the application and results of a more efficient method of breaking boulders using dynamite and water. This method is being used for the disposal of boulders that result from pinnacle and cap rock remaining after blasting on highways and job sites. This method is a faster and less expensive use of dynamite to reduce oversized boulders than the conventional rock hammer. The problem with excessive fly rock has been substantially reduced when using this technique over traditional methods.

Jan 1, 2001

By Deane Boddorff

A 440 Volt AC power line is a typical power source for energizing electric blasting cap circuits in driving hard rock tunnels. A common misconception exists that the caps actually see 440 Volts. This paper describes an analysis of the entire blasting circuit determining the current flowing and the voltage drops through each component. If, from such an analysis, one determines that the current to the caps is too low or too high, the components that require changing are easily recognized.

Jan 1, 1975