Search Documents

By Graeme J. Jameson

In conventional flotation machines, the recovery is strongly related to particle size. As particle size increases, the recovery also increases, reaching a maximum in the range 20 to 120µm. Beyond this range however, the recovery declines quite quickly. The reason for the decline in recovery observed with coarse particles can be traced to the effect of turbulence. Bubbles trapped in turbulent eddies rotate rapidly, and when the centrifugal force on a particle exceeds the retaining forces due to surface tension, the particle detaches. Since the centrifugal force varies as the cube of the diameter of the particle, and the attachment force varies simply as the diameter, being proportional to the length of the contact line, it is clear that detachment forces will predominate as the particle size increases. The corollary is that the recovery of coarse particles can be improved if the level of the turbulence in the cell can be reduced to a minimum. In this paper, a new type of flotation machine will be described, in which the particles to be floated are suspended in a fluidized bed. An up flow of fluidizing water is provided, by recycling liquid from the top of the cell. The recycle stream is aerated in a high-energy device that disperses the air into fine bubbles that capture the fines and ultrafines. Results are presented for several minerals and coarse coal. Keyword: fluidized bed flotation

Sep 1, 2012

By K. Sasaki, H. Miki, Y. Muta, T. Hirajima, G. P. W. Suyantara

"Selective flotation of chalcopyrite and molybdenite is continuing problem since its selectivity is not perfect and current NaHS process needs closed system flotation plant because of hydrogen sulfide emission on acidic condition. Some alternative additives investigated as chalcopyrite became hydrophilic and molybdenite kept hydrophobic. XPS analysis indicated chalcopyrite became hydrophilic since iron and copper sulphate, hydroxide was covered on the surface whereas molybdenite kept hydrophobic since only molybdenite can be seen. Flotation experiments of chalcopyrite and molybdenite mixture sample indicated excellent separation that 95% of molybdenite can be recovered as froth and 93% of chalcopyrite can be recovered as sink. Flotation experiments with real bulk flotation concentration indicated similar separation result compared with current NaHS additive system. Possible mechanisms and detailed phenomenon were investigated based on the surface analysis and thermodynamic calculation etc. this alternative additive is easy to handle compared with NaHS since it does not emit effluent gas and commercially preferable.INTRODUCTIONMany copper mine often associates molybdenite (MoS2) as trace mineral. It is important to separate molybdenite and copper mineral efficiently since molybdenite is valuable mineral and also contamination of molybdenite into copper concentrate decrease concentrate value. Conventional separation of copper sulfide and molybdenite has been achieved with sulfide bulk flotation followed by selective molybdenite flotation with NaHS addition since NaHS works as a depressant for copper sulfide (Bulatovic, 2010; Ansari and Pawlik, 2007b). However, this current process shows imperfect molybdenite recovery (Liu et al., 2012, Zanin et al., 2009) and depressant such as NaHS needs to be used under specific flotation plant since it might be environmental contaminant (Ansari and Pawlik, 2007a). there are still unknown on the effect of depressant NaHS, but one of the theory is NaHS reductant effect. It is worth to investigate the effect of other reductant as depressant on chalcopyrite. On this research, typical reductant, Na2SO3 are added to utilize for selective flotation of chalcopyrite and molybdenite."

Jan 1, 2018

By John C. Gathje, Rick Moritz, Wilhelm de Beer

"Froth flotation has a long history of success for the recovery and concentration of a wide variety of minerals of commercial interest. Both the art and science of flotation have progressed greatly, and as our knowledge has increased so has our ability to improve mineral separations and recoveries.One area of interest in recent years has been the flotation of refractory gold ores to recover the gold-bearing sulfides. In many instances, the use of conventional air flotation to concentrate these values has achieved only limited success. However, as a result of intensive research, Newmont Mining has expanded the boundaries of flotation, and it can now be used to successfully treat many gold-bearing sulfide ores as well as platinum and palladium ores. This has been achieved through the use of the N2TEC technology, which utilizes nitrogen as an inert gas in the flotation process.Laboratory and pilot plant investigations and a commercial plant have proven its worth. Compared to air, the patented N2TEC process has increased the gold recoveries of many ores by 5 to 15 percentage points, and improvements of an even greater magnitude have been observed. This paper describes the process development for the flotation plant now being operated at Newmont’s Lone Tree Mine located in Nevada, as well as development work that was done on ores from their Twin Creeks Mine also located in Nevada."

Jan 1, 2003

By C. Dorfling, P. Albertyn

"Hydrometallurgical recovery of metals from printed circuit board waste typically involves multiple leaching stages; conventionally, base metals dissolution by mineral acids is followed by leaching of gold using cyanide or halide based lixiviants. Alternative lixiviants for gold leaching can reduce the potential hazardous nature of operation. The aim of this study was to investigate the feasibility of using thiosulfate as lixiviant for gold leaching from waste printed circuit boards. Batch leaching tests were performed to investigate the effects of thiosulfate concentration (0.1 – 0.2 M), ammonium concentration (0.2 – 0.4 M), pH (9 – 10.5), solids content (25 – 50 g/L), and copper content of the feed material on the gold leaching behavior. The concentrations of metals in liquid samples were determined by means of inductively coupled plasma atomic emission spectroscopy, and high pressure liquid chromatography was used to evaluate thiosulfate degradation/consumption. The ratio of thiosulfate to ammonia was found to have the most significant effect on the extent of gold leaching, with the best gold extraction observed at a ratio of 0.5 mole thiosulfate per mole ammonia. The lower pH range of 9 – 9.5 generally produced better Au leaching, while low copper extraction during the first stage base metal leaching stages has proven to be detrimental to gold leaching from the residue. Thiosulfate degradation/consumption increased and gold extraction decreased with higher residual copper in the feed. An optimum gold extraction of 78.5 % from base metal leach residue was achieved with 0.2 M thiosulfate, 0.4 M ammonia, and 0.02 M cupric ions at 25°C in the pH range 9 – 9.5.INTRODUCTION Background and Aim The recycling of e-waste is becoming increasingly important as it provides certain economic benefits apart from the obvious environmental benefits. Printed circuit boards (PCBs) are found in most forms of e-waste and contain especially high concentrations of base and precious metals. Hydrometallurgical processes are often considered for the recovery of valuable metals from PCBs; these processes normally implement several leaching stages to selectively recover certain metals."

Jan 1, 2018

By T. A. Penzov

As a result of recent scientific and experimental studies new technical devices have been developed for monitoring and control the process of grinding. The description of microprocessor module MILLCONT 1 for control of the loading of the mill and microprocessor density control module DENSIMETER is given in the paper. The improved variant of the automatic system for ore grinding control in single-stage ball mill working in close cycle with a classifier with above mentioned technical means is shown in the paper. The loops for measuring and stabilization of the basic technological parameters (density of the ready pulp ? and fineness of grinding of the pulp ß) are described in the paper. The nowadays economic results in ore grinding process automation are given as well.

Jan 1, 2014

By Jiang Wenli, Zhang Yimin

In order to enhance the quality of iron concentrate from magnetic separation, reverse-flotation technology is often applied in an iron ore dressing plant.However, this technology has disadvantages in terms of operating cost,energy consumptionand environmental protection(Zhao, Wu& Wang,2005).Developing innovative equipment to process magnetite ore more-effectively is a way to get rid of these disadvantages of reverse flotation and improve the quality of iron concentrate.This paper describes the development of Complex Flashing-Field Magnetic Cleaner,a new kind of equipment based on the principle of combination of separation in magnetic field and separation in gravity field(Hao & Jiang, 2002).This innovative equipment possesses a tailor-made magnetic system and has the characteristics of a magneticfieldwhich can strengthen the formation of magnetic agglomerations and the dispersion of gangue mineralsto improvethe quality of separation.The automatic control system developed specifically for this equipment can further increase the accuracy of separation and stabilize the process.

Jan 1, 2014

By Slobodan B. Vujic

"Some twenty years ago, during construction of flotation in the “Veliki Krivelj” copper and non-metallic mine Bor, a computer supported system for remote controle of technological process was installed. Nowadays, the major part of equipment of this system is worn-out and technically old-fashioned. Having this in mind a decision was made to design a new computer supported information-management system for Flotation. The paper presents a concept and features of project solutions.For the requirements of remote monitoring and management of technological process in Flotation of “Veliki Krivelj”, Copper and non-metallic minerals mine in Bor, Yugoslavia (hereinafter: CNM Bor), a measuring-regulation equipment was implemented and a computer control system, adjusted for that time, built some twenty years ago. The major part of this equipment is today worn out and technically out of date.Having estimated that production and business activities could hardly be more efficient, operative and successful on one hand, and available mineral and other resources rationally exploited, the CNM Bor made a decision in 1999 to improve information-management function of Flotation. The idea was that the set task be realized through development and introduction into practice up-to-date integrated and computer-supported production-business information-management system. The first logic step in completion of this task refers to engineering-creative determination of information management system (hereinafter: IMS), namely to project elaboration.When considering the real system from technical, technological, organization, monitoring-management, logistic and business aspects, the Project on IMS of Flotation, should provide a rational, modern and, for the real system conditions, complete solution. The Project solutions should be based on the most recent knowledge from computer and measuring-regulation technics as well as from CIM concept (Computer Integrated Manufacturing)."

Jan 1, 2003

By Cesar Gomez, Jaime Álvarez, Lisette Wen

Laboratory mechanical flotation cells are extensively used in mineral processing for running batch flotation tests with a variety of purposes, for example assessing feed characteristics, determining flotation kinetics, or testing of new reagents and procedures. It is known that the results obtained depend on the operation mode, self-aerated or forced-air, and on the operating conditions selected for the test, in particular impeller speed and gas flow rate. These different results are a consequence of changes in size distribution of the generated bubble population and its remarkable evolution when frother is added; variations in bubble size affect the bubble surface area flux (BSAF), a variable which correlates with particle collection. Results of a two-phase (air-water) test program designed to measure bubble size for a variety of combinations of impeller type and speed, gas flow rate, frother type and concentration, and cell volume, demonstrated the wide range of BSAF with which the cell can be operated. The results obtained in this work demonstrated that gas dispersion in a forced-air lab flotation machine is significantly affected by the characteristics of the impeller/cell geometry combination in use, and the operating conditions selected. Operating conditions must be carefully selected and maintained during the test to ensure consistent results, in particular when frother concentrations below 20 ppm are used, because frother concentration in the cell will decrease as flotation progresses as a consequence of frother partitioning to the concentrate.

Jan 1, 2014

By Grigori I. Voiloshnikov

"The long-term studies on development of the technology for precious metals recovery using activated carbons executed by Irkutsk Research Institute of Precious and Rare Metals and Diamonds (IRGIREDMET) were finished by successful introduction of ""Carbon-In-Pulp"" process in Russia (1984).The review of some studies, accompanied by development, testing, introduction and subsequent improvement of considered technology, carried out by IRGIREDMET is submitted in this paper.The basic regularities of gold and silver adsorption onto activated carbons from cyanide, thiourea, chloride and other solutions are investigated using various phisical-and-chemical methods ( X-ray photoelectron spectroscopy, Voltammetry, X-ray microanalysis etc.). Using voltammetry it was found that gold cyanide is adsorbed onto activated carbon without chemical changes and partial reduction of gold is possible only during drying of carbon samples before analysis. Metallic gold and silver may be dissolved in boiling cyanide solution at argon atmosphere when they are in contact with activated carbon surface. Gold adsorption mechanism for activated carbons has great differences from that for the ion exchange resins. So the most probable mechanism for gold adsorption from cyanide solution is adsorption of neutral molecules Me n+[Au(CN)2-]n.X-ray quantitative microanalysis technique was developed to investigate gold adsorption kinetics onto spherical activated carbon. Gold profiles in granules of activated carbon for various adsorption conditions were tested (carbon particle size, mixing efficiency, adsorption time etc.). Mathematical methods were used to determine gold diffusion coefficient within activated carbon granule.The properties of various types domestic and foreign activated carbons were tested and the demands to activated carbons suitable for gold extraction were determined. As a result foreign and Russian activated carbons AG-90, AG-95 were recommended for use at Russian gold plants. Domestic adsorbents are cheaper in comparison with foreign activated carbons. The methods to restore carbon adsorption activity including acid treatment and thermal reactivation were tested and implemented."

Jan 1, 2003

By Lokesh K. Thakur, Peter Radziszewski

"For the cases tested (11 mills with 15 operating conditions), the Bond abrasion test steel media wear rate prediction gives an overall error of 73% and a standard deviation of 192.5%. However, total steel media wear in a given mill (ball or SAG) grinding process is a product of three recognised wear mechanisms -- impact, abrasion, and corrosion. A total media wear model can be defined on the assumption that the effect of each wear mechanism can be independently determined which allows for a total media wear model to be defined as the summation of the wear result of each mechanism (eqn. 1). It is assumed that impact and abrasive media wear is a function of the energy dissipated in impact and abrasion as estimated by a DEM charge motion simulation. Corrosive media wear is assumed to be a function of the media surface area present in a mill.The 3 initial tests developed (steel abrasion wheel, corrosion batch mill, impact chamber) coupled with the impact and abrasion energy spectra from a DEM charge motion simulation produced total steel wear rate results for the same cases as the Bond abrasion test giving an overall error of 0% and a standard deviation of 66.1%. However, if one were to consider the general observation that wear is proportional to energy and maintain the assumption that corrosion is proportional to media surface area then one would realize that the total media wear eqn. (1) can be reduced to eqn. (2). As this is a linear equation and one has, for the same mill, media wear and operating data for three different operating cases, one obtains three equations with three unknowns. This defines a simple matrix manipulation to determine the constants k1, k2 and k3. From the previous data set, we had 6 identical mills grinding the same ore but having different worn liner profiles and charge volume which provided the opportunity to average out the ki values over 20 combinations of 3 cases. With the determined ki values, it was possible to determine a second estimate of the contributions of impact, abrasion and corrosion to total media wear giving an overall error of 0% and a standard deviation of 56%."

Jan 1, 2003

By James Y. Oldshue

"Very seldom is it possible when contacting a gas with a slurry to measure the dissolved gas concentration in the slurry, and even where possible, equilibrium data with a suitable Henry.s law constant are seldom available.In general, by assuming a reasonable value for the dissolved gas concentration in the slurry and a corresponding equilibrium gas partial pressure P*, KGa values can be calculated for the pilot plant and then scaled up. Then, with the same P* value at various reaction conditions, a mixer can be designed which is quite satisfactory, having a reasonable design factor for full-scale performance."

Jan 1, 2003

By Milind Chikhale, Yogesh Reja, Keshav Tyagi

"Using computer models for process design is a well-established practice in the mineral industry. In recent years, there has been emphasis on modeling of processing plant as a whole. This paper covers development of a model for iron ore processing plant. Basic purpose of this model is to use simulation for efficient plant design and help in minimizing risk at the very initial stage of project. Feed to the plant is Hematite iron ore from a deposit located in Eastern India. Major processes in plant include multi-stage crushing, screening, grinding, classification, gravity and magnetic separation. Models for different process equipment were developed using METSIM and Bruno simulation software. Customized black box models and known mathematical models were used for predicting behaviour of processes. Data needed was identified based on the model type. The required data was arranged as per project requirement and processed for development and validation of model. Equipment models were developed and validated on the basis of process design basis, theoretical and empirical data from technical references, and bench scale and pilot scale testwork results. Validated process circuits were assembled to simulate and represent the entire plant process. The result shows expected variation in plant output as a result of variation in the feed. Study concludes by discussing potential applications of the model in plant design."

Jan 1, 2014

By Carlos Pereira, Fábio de São José, Francielle Nogueira

Votorantim Metals Corporation is one of the leader companies in the extraction of zinc in Brazil. One of its mines, located in the city of Vazante - MG, was composed by zinc silicate ores, but recent studies have indicated a change in mineralization type with arise of zinc sulphide’s ore bodies with disseminations of galena (PbS) and silver. The liberation size between sphalerite and galena in this ore occurs in very fine granulometry (approximately 18µm), fact that has negatively influenced into the flotation process. Aiming to reduce this problem, studies about the use of dispersing in the flotation process have started. Thus, this study investigated the action of different reagents dispersing on the stability of the suspensions. The tests were carried out with samples of mineral galena and sphalerite using four types of dispersing within two different dosages and two pH. The reagents tested were sodium hexametaphosphate, sodium silicate, carboxymethiylcellulose, and sodium polyacrylate. The results of the dispersion tests were analysed in relation to dispersion index. The tests with hexametaphosphate showed high dispersion for both galena and sphalerite. The sodium polyacrylate and arboxymethiylcellulose showed a high dispersion index for galena and a low index for sphalerite implying that reagent can be used in the concentration process of galena.

Jan 1, 2014

By Eduard Stefanescu, James M. Mwase, Egon Sehner, Stoyan Gaydardzhiev

"The study is focused on investigating the production of synthetic rutile of 95% purity or higher from a Norwegian ilmenite ore concentrate. This was to be achieved using a sequential process involving oxidative-reductive roasting at 975°C, followed by magnetic separation to further concentrate the sample and finally leaching with 20% HCl to remove mostly Fe-based impurities leaving behind synthetic rutile. The key process parameters considered were roasting time (1 and 2 hrs), leaching temperature (100, 125 and 145°C), pulp density (15 and 25wt%) and leaching time (3 and 6 hrs). The option of directly leaching the concentrate without pre-treatment was also evaluated. Test work was conducted using samples screened to a size fraction of 105-212 µm. Samples were leached in a 1 L glass autoclave. The reactor was hermetically sealed and thus the resulting pressure was not controlled but was dependent on the process temperature. The product from leaching was calcined and analysed via XRD and SEM to determine the purity of the product. The magnetic separation step was found to be ineffective and discontinued early in the study. Thus far a product with 97% synthetic rutile purity as analysed by SEM has been produced by directly leaching the concentrate at a temperature of 145°C, pulp density of 25wt% and leaching time of 6 hrs.INTRODUCTION The study investigates the use of a process route comprising oxidative-reductive roasting, followed by magnetic separation and then hydrochloric acid leaching and calcination to produce synthetic rutile from ilmenite concentrate. The grade of synthetic rutile produced should be suitable for chlorination to produce pigment grade TiO2. Hence the proposed process should produce a product consisting of no less than 95% synthetic rutile. Additionally, the product should have no more than 1.5wt% combined content of CaO and MgO (Zhang et al., 2011) as they tend to form high-boiling-point chloride leading to the malfunctioning of fluidized bed chlorinator (Cardarelli, 2008). Finally the product should have no more than 2.1wt% of Fe2O3."

Jan 1, 2018

By V. G. Prikhodko, G. I. Sukhinin, I. V. Yarygin, A. V. Fedoseev, S. A. Novopashin

"The first experiments on the vacuum drying of spherical clay sample are presented and the theoretical model of the process is considered. The model is based on the solution of the heat and the moisture transfer equations with the effective thermal conductivity and water diffusion coefficients for wet porous clay-like medium. The time and radial dependence of the temperature and the moisture were calculated for different initial conditions. The results obtained for the time dependence of the moisture content are in good agreement with the experimental results obtained in the initial period, when all the moisture in the sample did not freeze to form an ice crust. INTRODUCTION Capillary-porous materials very often occur in nature and in industry. A porous medium is a solid matrix with voids, or pores, which are continuously connected. These pores are usually filled with fluids or moisture, water vapor and air that can pass through the medium because the voids are interconnected. The void fraction in the solid matrix is referred to as the porosity. Porosity or void fraction is a measure of the void (i.e. ""empty"") spaces in a material, and is a fraction of the volume of voids over the total volume. The moisture content in porous media determines the properties of the porous body, its mechanical and thermo-physical properties, such as density, plasticity, viscoelasticity, swelling, cracking, and so on. Complex processes of heat and mass transfer occur in porous bodies when they are heated or cooled, during drying or freezing (Luikov,1966). The course of these processes depends essentially on the physical-chemical composition of the solid matrix of the porous body, on its fractal dimension, porosity and morphology. The clay and clay minerals are the most important porous materials in the history of the mankind (Mukherjee, 2013). Clay is a very fine grained, unconsolidated rock matter, which is plastic when wet, but becomes hard and stony when heated. It has its origin in natural processes, mostly complex weathering, transported and deposited by sedimentation within geological periods. Clay is composed of silica {SiO2), Alumina (Al2O3) and water (H2O) plus appreciable concentrations of oxides of iron, alkali and alkaline earth, and contains groups of crystalline substances such as quartz, feldspar, and mica. Building materials, bricks, and tiles, pottery, porcelain and faience are made from clay. Clay is used in the food and medical industry, and, not least, in the mining industry as a carrier containing aluminum, silicon and other valuable elements, as well as metals (copper, gold) as constituents, contained in the pores in the form of micro- and nano-particles or grains."

Jan 1, 2018

By David I. Verrelli, Boris Albijanic

"Froth flotation is an exceedingly complex physicochemical process. The convenience of distilling much of the complexity of the bubble-particle interactions into a single parameter has led to the continuing popularity of the classical ‘induction time’ to quantify the threshold for bubble-particle attachment to occur. Despite this popularity and the simplicity of the concept, there is no single universal method of evaluating the induction period. In this paper, we begin with a critical review of the available techniques for estimating the induction period. These are: back-calculation from experimental (micro) flotation tests; pushing a particle toward a stationary bubble (or vice versa) using an atomic force microscope (AFM); pushing a bubble toward a stationary bed of particles in the ‘Induction Timer’; pushing a bubble toward a stationary solid surface using the ‘integrated thin film drainage apparatus’ (ITFDA); and dropping particles onto a submerged stationary bubble using the ‘Milli-Timer’ device. Each one of these methods has advantages and disadvantages, and the best choice depends on the application. In the experimental section, we present quantitative comparison of the induction periods estimated using two different techniques, namely the Induction Timer and the Milli-Timer. The same particles were tested in each device, under the same conditions. It was found that by tuning the operation of the particle pick-up device, similar estimates of induction period could be obtained to the estimates made by direct observation with the Milli-Timer. In the former device a bubble is driven toward a particle bed at a controlled rate, whereas in the latter a particle’s motion is governed by the hydrodynamics. The potential to match these presents an intriguing prospect for better understanding the bubble-particle interaction, and the possibility to ‘calibrate’ the simpler Induction Timer against direct observations."

Jan 1, 2014

By Dilip. Makhija, Asim. K. Mukherjee, Tamal Ghosh, Abhay Patra

In India around 15-20% of Run of Mine (ROM) from any iron ore deposit reports to slime dams as byproduct of iron ore beneficiation process. The proportion of iron ore slime to ROM will increase in future with higher proportion of lean grade ores in ROM. Furthermore, tonnages of iron ore slime will also increase with increasing demand of iron concentrate. Presently, this slime is stored in the dam in the absence of beneficiation technology. A beneficiation flowsheet has been developed at Tata Steel. This process produced concentrate of 2.2% alumina with 40 % yield from slime of 7-9% alumina. The iron content in the reject will be less than 40% thus adhering to the regulatory norm. Pilot scale study show waste from slime beneficiation is a good raw material for making a variety of building materials. Waste from slime beneficiation also has soil amendment properties. Pilot scale studies show productivity of rice increased when the waste of slime beneficiation process is mixed with soil. On commercialization of this zero waste technology slime generated from the iron ore washing plant will be completely used. In this paper the result of the pilot scale studies on slime beneficiation and utilization processes towards soil making and making of building materials are discussed in detail.

Jan 1, 2014

By Takaaki Wajima

The slag was attempted to be converted into the adsorbent for phosphate removal from aqueous solution using the alkali fusion method. The slag was mixed with NaOH powder (NaOH / Slag = 1.6), and then the mixture was heated at 600 ? for 6 h to prepare the precursor. The precursor was stirred at room temperature in distilled water to synthesize the adsorbent, and the removal ability of the obtained adsorbent for phosphate from aqueous solution was investigated. The products, including hydrocalumite and calcite, were synthesized, and the removal efficiencies of the adsorbent for F- and PO43- showed higher than those of raw BF slag, especially removal of PO43- are excellent (99 %), while the removal of Cl- , SO42-, NO3- and Br- was minor. The adsorbent could remove PO43- selectively in the co-existing solution of Cl-, NO3-, F-, SO42- and Br-.The equilibrium adsorption capacity of the adsorbent for PO43- was extrapolated using Langmuir and Freundlich models, and experimental data are found to fit Langmuir than Freundlich. The calculated maximum adsorption capacity of the adsorbent for PO43- is higher than other adsorbent reported previously. The high affinity of the adsorbent for PO43- in aqueous solution was caused by the formation of hydroxyapatite [Ca5(PO4)3(OH)] and brushite [CaHPO4?2H2O]. The prepared adsorbent is expected to be anew inorganic adsorbent for the removal of phosphate ion from wastewater. Keywords: Blast furnace slag, Alkali fusion, Phosphate removal, High selectivity

Sep 1, 2012

By Anuttam Patra, Romain Bordes, Andreas Fredriksson, Tommy Karlkvist, Krister Holmberg, Kota Hanumantha Rao

Almost all of the flotation reagents used today were discovered by continued application of empirical methods and/or trial and error experimentation. Moreover, with the metal-ion specific approach used so far, it is difficult to separate the minerals containing the same constituent metal ion. A critical assessment of molecular recognition processes involved in biomineralization suggested the possibility of using reagents which are surface specific. The concept that the molecules consisting of two or more functional groups having appropriate spacing between those so as to achieve structural/stereochemical compatibility during interaction with the mineral surface exhibit structure-specificity is thought to be extended to the design of specific collectors in flotation processes. In the present study, for the first time, a rational design of surface active molecules, and thereby the recognition of crystal faces (of minerals) by these molecules through structural and stereochemical matching is being utilized successfully to selectively float various minerals. For this purpose, carboxylate-based collectors (for mineral specific flotation of calcium minerals) as well as xanthate-based collectors (for mineral specific flotation of sulphide minerals) with a fixed alkyl chain length but having two functional groups with varying geometrical distances (separated by a spacer of one, two and three carbon atoms) between them have been synthesized. In this article, we have discussed the design, synthesis, purification of these novel mineral specific collectors as well as their important solution parameters in relation to flotation processes.

Jan 1, 2014

The flotation of nickel sulphide minerals is normally difficult in the presence of serpentine minerals due to the coating of serpentine particles on the nickel mineral surface. To improve the flotation, dispersants such as polyphosphate and carboxy methyl cellulose are normally used to remove the slime coating. However, in the flotation using high ionic strength process water, these dispersants are invalid due to their ionic nature. In this study, a new type of non-ionic dispersants, Pluronic triblock copolymers were examined with an objective of improving the flotation of ultrafine pentlandite (a nickel sulphide mineral) in the presence of lizardite (a serpentine mineral) in saline water. Three Pluronic triblock copolymers varying in solubility and hydrophile-lipophile balance (HLB) values were studied by flotation tests, settling tests and froth measurement. It was found that two of the copolymers improved pentlandite flotation against lizardite, and one copolymer deteriorated the flotation. The effect of Pluronic triblock copolymers on the flotation was actually linked to their dispersibility and foamability, which were governed by their physical properties. The two copolymers with a higher solubility or HLB value produced more stable mineral suspensions and more stable froth in the flotation resulting in better nickel grade and recovery in both rougher and cleaner flotation. Keywords: ultrafine particle, flotation, slime coating, dispersion, saline water, triblock copolymers

Sep 1, 2012