Search Documents

By Y. Yhang, D. C. Sego

ABSTRACT This paper evaluates the potential of freeze-thaw dewatering using Albian mature fine tailings (MFT). Freezing tests were first performed to study the effect of freezing rate on dewatering efficiency. Lower freezing rate resulted in higher thawed solids content and shear strength. Subsequently, large strain consolidation tests were conducted to investigate consolidation behaviour and how it is affected by freeze-thaw. The consolidation behaviour was presented in terms of effective stress versus void ratio and permeability versus void ratio. The results can be used to predict the field behaviour of Albian MFT and optimize the application of freeze-thaw for MFT dewatering.

Jan 1, 2014

By C. V. Deutsch, O. Babak, J. G. Manchuk

High levels of geological heterogeneity occurring over relatively short distances pose a challenge to the unconventional open-pit techniques used in oil sands mining. There is strong motivation to mine selectively and minimize dilution and loss; however, the large equipment and high mining rate used to meet production targets tend to reduce selectivity. A numerical model is developed to account for geological complexity, mining equipment, regulatory criteria, and other operational parameters. This framework is used for more accurate forecasts, optimization of equipment, and other operational decisions. An example demonstrates the approach in light of Alberta Energy Regulator criteria.

Jan 1, 2014

By Kristopher John Shelswell

The work in this paper describes the theory, development and analysis of a computer model simulating a mine operation moving material using concurrent decline ramp truck haulage and skipping practices. This simulation was designed specifically to assess the performance of the truck haulage component and to expand on the scope and capabilities of traditional TKM fleet calculations. Haulage fleet simulation results were similar to TKM calculations for the lower to moderate production rate cases. However, comparisons of ramp-up and high production rate scenarios indicated that the simulation model was significantly more sensitive to operating practices and factors not accounted for by calculations derived when using a single TKM figure. Given the proper calibration of inputs and logic, the simulation model was additionally capable of providing information associated with general mine operations efficiency. Further benefits of the simulation model over a TKM approach included logistical assessments such as production schedule feasibility, productivity trade-off quantifications for proposed operating practices, and the validation of mine resource utilization scheduling. The simulation model was able to expand on traditional methods to approach planning and logistics by considering factors such as truck queuing, real-time traffic interactions, random events, and competition for resources on mine productivity.

May 1, 2013

By K. N. Subramanian

Previously reported work on total oxidative leaching of chalcopyrite concentrates ha s shown that high copper extractions are obtained at 210°C and 0.4 MPa oxygen pressure. A simple integrated flow sheet using pressure leaching, solution treatment involving precipitation with a calcium base, and electrowinning to produce wire-bar-quality copper is described. Reagent and energy requirements developed from this work indicate that the process could be attractive for small operations where a smelting-refining complex cannot be justified.

Jan 1, 1978

By Terry Gerritsen, Sylvain Picard, Bruce MacKay

Virtually all new technologies require a control system. Any intense process has many process variables that react quickly making manual control difficult. Control system design has a significant impact on the success of a plant especially during ramp-up. New technology projects are particularly sensitive to control system design as the process response is unknown. This paper discusses the important factors encountered in the design of a control system for a new technology. Examples are given of successful new technology plant start-ups where tight coordination of the process control system implementation, process design and selection major equipment led to rapid ramp-ups.

Jan 1, 2011

By X. -G. Chen, K. Liu

Nowadays, great interests are rising on aluminum alloys for the applications at elevated temperature, driven by the automotive and aerospace industries requiring high strength, light weight and low cost engineering materials. As one of the most promising candidates, Al-Mn-Mg 3004 alloys is found to possess considerably high mechanical properties and creep resistance at elevated temperature resulted from the precipitation of a large number of thermally stable dispersoids during heat treatment. In present work, the effect of Fe contents on the evolution of microstructure as well as high temperature properties of Al-Mn-Mg 3004 alloys has been investigated. Results show that the dominant intermetallic changes from a-Al(MnFe)Si at 0.1 wt.% Fe to Al6(MnFe) at both 0.3 wt. % and 0.6 wt. % Fe. In the Fe range of 0.1 to 0.6 wt.% studied, a significant improvement on mechanical properties at elevated temperature has been observed due to the precipitation of dispersoids, and the best combination of compression strength and creep resistance at 300°C is obtained in the alloy with an intermediate Fe content (0.3 wt.%) with finest size and highest volume fraction of a-Al(MnFe)Si dispersoids. The superior properties obtained at 300°C makes 3004 alloys more promising for high temperature applications. The relationship between the Fe content and the precipitation of stable dispersoids as well as the materials properties has been discussed.

Jan 1, 2015

By J. -F. Lepage, M. A. Tomlinson, K. K. Murray

"The Éléonore mine, located in the James Bay region of Northern Quebec, generates a gold bearing flotation concentrate rich in pyrrhotite. Direct leaching of the finely ground concentrate results in high cyanide consumptions and poor recoveries, so effective pre-treatment to passivate the pyrrhotite is required before leaching. Following a number of process upsets at the mine, test work was performed to better understand the requirements for passivation so a more effective operational strategy could be implemented. This paper outlines the testing and implementation of the new strategy at Éléonore.ÉLÉONORE CONCENTRATOR The Éléonore mine is located 800 km north of Montreal, in the James Bay Region of Quebec, Canada. The ore, containing gold disseminated in sulfide minerals and free fine gold in silicate gangue, is crushed in a two-stage crusher plant before being ground in a single 9,000 kW ball mill. The ball mill is in closed circuit, with about 25% of the cyclone underflow passing through a gravity plant with two, 48” Knelson concentrators. Gold recovery in the gravity circuit varies between 15 and 20%, with gravity concentrate leached daily in an Acacia intensive leach reactor. Cyclone overflow, at a target P80 of 65 microns, flows to the flotation plant where the gold bearing sulfide minerals, mainly pyrrhotite and arsenopyrite, are recovered to concentrate with a mass pull of about 5%. The flotation concentrate, typically containing between 80 and 120 g/t of gold, is thickened and finely ground using a 1500 kW Isa Mill. The finely ground concentrate is diluted, to generate a slurry with about 32% solids by weight, before feeding the leach plant. Initially the concentrate slurry is pre-treated with oxygen and lead nitrate, to passivate the sulphide minerals before cyanide is added for gold dissolution. Gold is recovered from the leached slurry using carbon-in-pulp (CIP). The flotation tailings are also thickened and gold is recovered in a dedicated leach-CIP plant."

Jan 1, 2017

By F. Siciliano, D. Bai, S. Yue, A. M. Elwazri

The influence of niobium addition and very low temperature (`cool') deformation on the microstructure and properties of low carbon microalloyed steels was investigated. In this work, the specimens were heated at 1200°C and held at this temperature for 20 minutes. Some specimens were aged at 400°C for times ranging from 10 minutes to 10 hours followed by air-cooling. Others were subjected to deformation at 400°C (`cool deformation') prior to aging. It was observed that the proportion of acicular ferrite was increased as the amount of Nb was increased. It was found that cool deformation increased both yield and tensile strengths significantly compared to that of the aged only specimens.

Jan 1, 2005

By M. B. Shongwe, R. K. K. Mbaya, C. K. Thubakgale, P. Mendonidis

"A low-grade nickel-bearing ore was pre-concentrated on a SB40 laboratory model Falcon Concentrator. Three size fractions, -212+125, -125+75 and -75 µm were tested with the intent to upgrade the nickel content by reducing their content of fine silica, which becomes amorphous during leaching. Separation of silica from nickel-bearing magnesium silicate minerals; hornblende, clinochlore and talc, was more efficient in the finer particle sizes, -125+75 and -75 µm, and at high G-forces. For these two size fractions, nickel was upgraded from 0.06 to 0.07%, with a reduction in silica content from 52.12 to 50.71%. Leaching of feed samples prior to pre-concentration resulted in the formation of amorphous silica, indicative of the presence of fine silica in the samples. Leaching of nickel from the -125+75 µm fraction increased with increasing G-force and feed pulp percent solids, while that of -75 µm was not influenced. The optimum nickel recovery was 15.68% to the Falcon underflow, using the feed size fraction of -75 µm, 30 G and a feed pulp solids content of 10% solids, after 120 minutes of treatment.INTRODUCTION A low-grade South African nickel-bearing ore with about 0.06% Ni was previously studied for atmospheric pressure acid leaching using sulphuric acid. The study was motivated by the continuing search for methods to treat of low-grade ores, which appear to be an increasingly important source of valuable metals as a result of a declining production from rich sulphide ores. Nickel is a base metal that is used as an alloy in steelmaking and chemical industries because of its resistance to corrosion (Haudet et al., 2015). Nickel laterite ores with grades lower than 1.50% Ni are considered to be complex ores, accounting for 70% of the global nickel reserves (MacCarthy et al., 2016). Their complex nature may be attributed to the indefinite mineralogy of these ores, in which nickel may occur in more than one mineral host. In some cases, nickel may be finely disseminated in the ore. The grade of such an ore and complex mineralogy do not justify the application of pyrometallurgical methods for extraction of nickel (Zhu et al., 2012). This suggests that there is a need for less expensive alternative methods of extraction. This study investigates the application of centrifugal gravity concentration, using the Falcon concentrator, followed by leaching to determine the effect of pre-concentration of the ore prior to extraction by atmospheric pressure leaching with sulphuric acid."

Jan 1, 2017

By Gerry Doeksen

The paper deals with three case studies: (a) the handling of wet concentrates (5 to 8 per cent moisture) through feed bins; (b) the handling of the same product in rail cars; and (c) the handling of dry concentrates (less than 0.5 per cent moisture) through feed bins. In each case, the paper discusses the problems of rat-holing. In each of cases (a) and (c), there is a discussion on the consequent extreme variations of feed rates coming from the feeders, making automation of process control difficult to impossible. Currently available bin-flow theory and flow property tests are used as aids in redesigning the bins. The paper concludes with illustrations of the final results after the redesigned hoppers were installed and tested. There is also a discussion on the advantages of the new mass-flow bins on adjacent feeder performance.

Jan 1, 1970

By P. Amelunxen

It is well-known that the particle breakage mode that occurs in a semi-autogenous mill is significantly different from that which occurs in a ball mill, enough so to warrant very different lab scale breakage tests and scale-up models. This phenomenon, at the plant scale, leads to changing process constraints depending on the particular properties of the ore. For example, hard or coarse ores might bottleneck the SAG/AG mill throughput, while the ball mills might constrain throughput when milling soft or fine ores. Because the power draw of a ball mill is fairly constant compared to that of a SAG/AG mill, periods of SAG/AG mill bottlenecks lead to increased ball mill circuit specific energy consumption and a finer grinding circuit product size, which together constitute a loss of efficiency of the overall process. Because HPGR circuit throughput is less sensitive to changes in ore hardness, this situation is less common or severe in those circuits. Furthermore, the ball mills are somewhat decoupled from the upstream crushing circuits through the use of surge bins, which also helps to mitigate this effect. As a result, ore hardness variability constitutes a significant cost penalty that should be applied to SAG mill/ball mill/pebble crusher SABC circuits when evaluating the relative economics of different grinding circuit configurations. Nevertheless, the issue is by-and-large ignored, because most current HPGR trade-off studies are based on averaged ore hardness parameters. This paper provides an estimate of the magnitude of this penalty for a typical operation by using Monte Carlo simulation methods and plant data from Freeport-McMoRan?s autogenous, semi-autogenous, and HPGR-based comminution circuits. A case study from an in-house 96K t/d sulphide project is presented to illustrate the concept. It was found that by including variability effects, the trade-off NPV of the HPGR circuit over that of the SAG mill circuit increases to $84 million from negative $33 million, effectively reversing the original decision of selecting a SAG mill circuit for the fixed hardness case.

Jan 1, 2012

By H. S. Price, F. N. Kissell, R. C. McCulloch, J. C. Edwards

"The methane em1ss10n from deep coalbeds which are actively mined is a serious problem facing the mining industry today. Pinpointing the source of methane and predicting the emission of this gas from these coalbeds is necessary if preventive techniques are to be effectively used to control methane emission. In general, because most coalbeds have water associated with them, the system to be studied may be either single-phase (methane gas) or two-phase (methane and water). Because coal mine geometry is complex and the fluids have variable properties as functions of pressure and methane concentration, the differential equations describing the flow of methane and water are not amenable to analytic solution, but must be solved numerically using high-speed computers. This paper presents the development of such a complex mathematical model along with some preliminary applications of the model to methane emission from one- and two-dimensional coalbeds with and without water present."

Jan 1, 1973

By Roger M. Jones

This paper comments on developments in bulk shipping which will be of direct interest to those who are considering the shipment of dry bulk minerals out of Nova Scotia by water. Various conveying systems, and the slurry system of loading, are considered, and the role of deep water ports as a catalyst to other industries is stressed.

Jan 1, 1971

By W. J. Dick

THE purpose of this paper is to point out, briefly, the importance of the coal mining industry of Alberta and to stress the economic factors that hinder its development; also to offer suggestions relating to the major problems of the industry. The minor problems will not be dealt with in detail, because, if the major problems are taken care of, it is felt that the industry itself can take care of ,he remainder. COAL MINING NO LESS IMPORTANT THAN GOLO MINING The large increase in metal mining development in all provinces of Canada, excepting Saskatchewan, Alberta, and the Maritimes, has had the effect of focussing public attention on this branch of the industry. The fact, also, that this development came at a time of depression has been of immense benefit to Canada as a whole. On account of the necessity and consequent demand for gold, with its attendant increase in price, through government action, from $20.67 per ounce to $35.00 per ounce, it is safe to say that the public of Canada have become, today, gold mining conscious. While everyone admits the great value. of the gold mrn111g industry, nevertheless, the equal value to Canada of certain other industries must not be lost sight of. The coal mining industry, in particular, is worthy of greater public and government support than has been accorded it in the past. It would seem unnecessary to stress this matter to a meeting of the Canadian Institute of Mining and Metallurgy, but unless certain facts are brought to your attention, there is danger that the coal mining industry will not be developed to the extent its national importance deserves. Too many public men and men in authority are unaware of the value of coal mining.

Jan 1, 1936

By F. R. Archibald

SINCE the opening of the Beattie mine, in 1933, the concentrate produced by flotation has been considered refractory. As the gold extraction by cyanidation was poor, the concentrate, during the first four and a half years of operation, was shipped to a smelter for further treatment. After the installation of the cyanide plant, in 1934, seventy per cent of the gold in the concentrate was recovered before shipment to the smelter. In 1937, a roasting plant was built so that treatment might be complete at the mine. Much experimental work had been done by a number of investigators prior to the installation of the roasters, but none of them had seriously attempted to identify the causes of, or the elements responsible for, the refractory behaviour of the concentrate. Intensive investigation in this direction commenced in the Beattie lab-oratory in July, 1938, has led not only to the identification of several causes contributory to the refractory behaviour, but also to revisions in procedure and principles with respect to roasting Beattie concentrate in particular and arsenical concentrates in general. The accuracy of the identification of these causes and the soundness of the principles is borne out by interpretation of roasting plant records, by improvements and simplification since applied. to plant operation, and also by laboratory and test-plant results on arsenical concentrate produced by another mine. It is the purpose here to present an account and interpretation of the laboratory investigation, together with a correlation of laboratory and plant results. Incomplete extraction of the gold by cyanidation after roasting is due primarily to the nature of the material roasted, and secondarily to the manner in which it has been roasted. There is a possibility that better extraction may be obtained by improvements in both particulars.

Jan 1, 1939

By David Burchell

Duckbill mining is probably the simplest method of loading coal mechanically at the face in underground mines. It is a means of reducing the amount of physical labour required to produce a ton of coal. In effect, it is merely shaker conveyor mining brought up to date with the addition of a self-loading head or 'duckbill' on the end of the conveyor line. Any mechanical device used to load coal is a means of supplanting the human muscles as the medium for getting the coal off the floor into the transportation equipment. There can be no argument with the conclusion that a man can lift so much and no more. He can load more tons of coal on a low conveyor, because the lift is less, than he can in a pit car two, three, or even four feet high. Thus it follows that, if the lifting operation is entirely eliminated, the man should be able to produce even more coal. A mechanical operation is essentially a multiplication of physical strength. Although there are various ways in which coal can be loaded at the face by mechanical means, there is, perhaps, none more adaptable than shakers equipped with duckbills. This is particularly true for thin seams and in mines having heavy, tender top conditions which require close timbering. However, as we are discussing duckbill mining, we will make no further reference to any other type of equipment. The first, and to date the only, mine in eastern Canada to adopt a system of mechanical loading at the face is the Franklin mine of the Bras d'Or Coal Company, Ltd., at Bras d'Or, N.S. An experimental Goodman shaker conveyor with a self-loading head, or duckbill, was installed in this mine in 1940. Since that time other units have been placed in operation so that, today, this mine is completely mechanized. The method of operation 1s room-and-pillar. The operation is carried on in a 42-in. seam, which lies 420 feet beneath the Sydney Main or Harbour seam in the Sydney Mines basin. The slopes bear N.25 30'E., dip 10 per cent seaward, and are about 6,000 feet in length. The physical conditions of this seam do not make it particularly adaptable for complete mechanization as it contains a large amount of foreign material, such as clay intrusions or wash-outs and iron pyrites. These clay intrusions, known locally as 'troubles', vary in thickness from a few inches to as thick as eighteen feet and usually replace the coal to the full height of the seam.

Jan 1, 1947

By P. Roman, L. Daneshmend

"During the last decade, mining companies have been overwhelmed by technological solutions to perceived problems. This is particularly true with information technology where rapid advances have resulted in a professional climate characterized by technomania — the perception that failure to adopt emerging technologies will result in a loss of competitive advantage. This paper describes the applicability of structured analysis and design techniques as an appropriate methodology for integrating emerging technologies in the mining industry. The potential of this approach to improve overall mine effectiveness through improved communication and co-ordination between operations and maintenance is discussed. IntroductionA strong working relationship between the operations and maintenance departments in both open pit and underground mines is fundamental to the overall success of the mining endeavour. Unfortunately, for many mines, this characterization is far from accurate. Short-range production targets dominate the day-to-day management of the mines. This can be seen in Bostwick and Buchanan’s (1993) report on American Barrick Resources efforts to achieve an aggressive 415 000 tpd mining program at their Goldstrike operation in Nevada. When production managers do not meet their quotas, the finger is often pointed at maintenance. As a result, a confrontational culture can develop between the two organizations, resulting in a lack of cooperation that exacerbates the problem. Historically, production planning has taken priority over maintenance planning. This is reasonable since production is the primary purpose of the mine with maintenance serving in a support role. This basic relationship remains intact today. However, the trends toward mechanization, increasing levels of automation, and larger equipment, have resulted in increased reliance on the equipment used in the mine. As a result, downtime costs now go well beyond the direct labour associated with the repair of the machine. Lost production costs due to downtime resulting from failed equipment are becoming an increasingly important factor in determining a mine’s overall economic performance."

Jan 1, 2001

By F. Awotwe-Appiah, P. Koshy, A. Y. Fosu, J. Dankwah, J. R. Dankwah

Ghana currently exports its bauxite raw without any value addition. Gradual depletion of high grade bauxite (with high alumina content) and the emergence of low grade bauxite (with high iron oxide content) calls for novel and inexpensive ways to recover alumina from these low grade ores. Bauxite users have indicated their willingness to pay 10% to 50% higher for a corresponding reduction in impurities by a similar amount. This project therefore investigates the carbothermal upgrading of the Ghana Awaso bauxite using waste polypropylene as reductant in a locally designed gas-fired furnace. Composite pellets of low grade bauxite sample (assaying 45% Al2O3) containing pulverised waste polypropylene were formed, oven dried, placed in fireclay crucible and fired for 30 minutes. The magnetic fraction after reduction was separated by a Low Intensity Magnet and weighed. It was observed that up to 97% of the iron oxides (occurring as hematite and goethite) could be separated into the magnetic fraction as magnetite leaving a nonmagnetic fraction with over 98% Al2O3 as opposed to the 45% Al2O3 in the as-received bauxite sample. This research direction provides yet another simple but effective way for simultaneously upgrading low grade bauxite and recycling waste polypropylene, whilst at the same time decreasing the amount of waste material generated as red mud after the Bayer process.

Jan 1, 2015

By Adrian Dance

Barrick Gold Corporation?s wholly owned subsidiary, Barrick (Granny Smith) Pty. Ltd. operates the Granny Smith operation in Western Australia and has been operating a SAG/ball mill (SABC) circuit for a number of years processing a blend of secondary crushed, open pit and underground material. With closure of the open pit in 2008, Granny Smith was considering different options to process underground only material at a lower throughput. Using the existing equipment available on site, a number of circuits were evaluated by Metso Process Technology & Innovation (PTI) through modelling and simulation. A single stage SAG mill circuit was selected based on power requirements and operating efficiency. In April 2008, Granny Smith started operating their SAG mill in single stage, processing primary crushed feed and using their existing pebble crusher for scats. Smaller cyclones were used to control the final grind size. PTI surveyed the new single stage circuit in July 2008 under normal and high rock load conditions to show the effect on final grind size. Granny Smith continued to operate this circuit until the end of 2009, when alternate feed sources resulted in a return to the complete SABC circuit at a higher tonnage once again. The variable speed, single stage SAG mill proved itself to be very efficient and flexible option to process the hard underground Wallaby Deeps material. This paper will review circuit performance following the conversion to single stage in comparison with the full SABC circuit.

Jan 1, 2012

By H. Zhu, Q. Jiang

The leaching kinetics of iron during the atmospheric direct leaching (ADL) of marmatite concentrate was studied under the following conditions: reaction temperature of 343-383 K, slurry pressure of 0.3-0.7 MPa, particle size of (-74 ?m, +63 ?m), (-63 ?m, +44 ?m), (100%-44 ?m). The statistical effects of reaction temperature, total pressure and particle size of concentrate on the extraction and the leaching rate of iron were analyzed. The results show that reaction temperature is a significant factor while slurry pressure and particle size are not statistically meaningful with respect to the extraction or the leaching rate. The extraction of iron fits better to the mixed-controlled shrinking core model and the apparent activation energy was calculated to be 37.66 kJ/mol. The leaching of iron is mixed controlled by the interfacial chemical reaction and diffusion across the product layer.

Jan 1, 2014