Search Documents

By Steven Doyle

Presentation Outline ?Introduction to Brunswick Mine ?Mining Needs and Drilling Trends ?Maintenance Program ?Back to Basics ?Results ?Additional benefits Introduction Xstrata Zinc Brunswick Mine ?No. 12 deposit discovered in 1953, pilot mining 1957, u/g mining began in 1964 ?Zinc, copper, lead and bulk lead/zinc concentrates ?Since 2007, a fully owned division of Xstrata Zinc Canada ?Over 132Mt milled 3.4 % Pb, 8.8 % Zn and 102 g/t Ag ?Deposit dips approximately 70 degrees; strike length of 1200 m; currently mining from 250 m to 1125 m depth

Nov 1, 2011

By Y. Huang

Corrosion of GaAs in aqueous electrolytes is a major limitation in implementing GaAs-based photoelectrochemical solar energy conversion systems, In this work, the corrosion behavior was investigated by electrochemical methods and surface analysis approaches, in both H2SO4 and NH3?H2O solutions, Open-circuit measurements showed that the cleaned GaAs surface was very sensitive to water/air, Impedance measurements for n-GaAs showed that an inductive loop only appeared at a high corrosion rate because a reaction intermediate is the oxidant for a further decomposition step in combination with chemical reaction with water, The results suggest that the same corrosion/decomposition mechanism occurred on n-GaAs in the two solutions, When the surface-hole concentration was low, the hole injection or generation process was the rate-determining step, At large reverse bias on n-GaAs, with high-hole concentration, the corrosion rate was limited by a Faradaic adsorption process, involving an adsorbed intermediate, The different surface compositions after corrosion in the two solutions can be explained by the dissolution of As(0), Further oxidation of As(0) to As(III) in NH3?H2O solution is still slow, as suggested from X-ray photoelectron spectroscopy (XPS) analysis,

Jan 1, 2005

By C. S. Lord

"The Regal Silver mine is 5 miles north-northwest of Albert canyon; a station on the main line of the Canadian Pacific railway; 21 miles east of Revelstoke; British Columbia.Development, commenced in 1918, comprises more than 8,000 feet of workings from six adits, one of which extends into the Regal Silver property from the adjacent Snowflake ground. Production has been limited to a little tungsten concentrate recovered recently from a few r..undred tons of ore treated in a small underground mill. The property has received some attention as a possible source of tin. The deposits are large quartz veins containing irregular sulphide bodies. Ore minerals normally make up less than 1 per cent of the veins and include pyrite, galena, sphalerite, scheelite, and stannite. The veins are approximately parallel with the bedding of the enclosing graphitic, siliceous to calcareous, slates and argillites. These strata are of Precambrian age, strike about northwest, and dip northeast. No other rocks are known in the vicinity of the workings . Granitic rocks, intrusive into t'he sediments, outcrop 4 miles to the southwest and 7 miles to the northeast and may underlie the property at no great depth."

Jan 1, 1954

By C. -G. Berg, J. T. Tuominen

Since the beginning of the 20th century, energy efficiency in copper smelting has been improved by a factor of 30 as a result of adopting autogenous smelting processes with more and more efficient waste heat recovery systems, increasing use of oxygen enrichment and countless smaller improvements. Nevertheless, energy in the form of electricity and fuels continues to be the biggest contributor to smelter operating cost. Metallurgists around the world are under constant pressure to find ways to save those precious megajoules wherever they can. One area that is often neglected is the removal of water contained in concentrates. Copper flotation concentrates, as delivered to a smelter, typically contain some 8–12% moisture. This moisture must be removed and the only way to do this is by evaporation, which consumes a lot of energy. Several studies have shown that the most efficient way of removing this moisture is to use a steam- heated indirect dryer—the least efficient way being the feeding of wet concentrate directly into a smelting furnace. Even in the most efficient smelters that employ modern steam drying, the energy needed to remove the moisture from the concentrates constitutes over 15% of the total energy consumption of a smelter – acid plant complex. The major steps that have been taken in the past to lower the energy consumption of moisture removal are the use of drying in general and the adoption of steam drying. The energy efficiency of concentrate drying has been improved by 25% over the last 20 years. The latest giant leap in this area, the Kumera Heat Recovery Dryer, is the result of Kumera’s long-term development in improving the efficiency of concentrate drying. The Heat Recovery Dryer is a novel application of steam drying that uses the waste heat from dryer exhaust gas for drying concentrates, thus, cutting the energy consumption by a further 30%. This paper discusses energy consumption in copper smelting in general and analyzes the energy consumption of concentrate drying in detail. Different dryer types are compared especially from the perspectives of energy consumption and environmental emissions. Applicability of different energy sources for drying is evaluated and discussed. The principle of the Kumera Heat Recovery Dryer is presented along with results from extensive continuous pilot plant tests. Potential applications and the feasibility of Kumera Heat Recovery Drying technology are discussed.

Jan 1, 2019

By Jürgen Antrekowitsch, Gerardo R. F. Alvear Flores, Mehmet Ayhan, Christoph Zschiesche

Synergies between copper and lead extractive metallurgical processes enable the processing of a broad range of polymetallic materials. However, this complexity also brings some challenges expressed in terms of complex intermediates and final products. For instance, based on the limited solubility of Cu and Ni in crude lead bullion additional phases will appear during the crystallization of the melt. Beyond the need for continuous optimization of metallurgy the control of phase solidification is a further important pillar to achieve a more efficient process by minimizing the amount and cycles of reverts. This paper describes the microscopy study of one of the most relevant intermediate in the Cu and Pb metallurgy, the Cu based alloy and highlights the importance of applying a well-controlled cooling sequence to improve the overall process efficiency. INTRODUCTION One of the key aspects in Aurubis’s 2025 vision is to move towards the implementation of a multi metal recovery strategy. The implementation of this new multi metal vision is supported by the long tradition of the company, founded in 1866 as Norddeutsche Affinerie, and further developed by adopting modern copper smelting and lead smelting technologies for the processing of primary and secondary materials. The combination of these assets have already build the basis for processing of complex materials in the copper and lead circuits implemented in Aurubis’s facilities. The addition of a new smelting facility, will enhance these capabilities. Aurubis current flowsheet combines Cu, Pb and Zn metallurgy. This includes primary smelting of copper concentrate, processing of secondaries (residues, slimes, slags) and recycling materials (scrap, shredder material, e-scrap). These broad range of materials contain not only the mentioned base metals but also a number of minor metals that requires to be properly managed to ensure efficient recoveries and quality of the targeted metals.

Jan 1, 2019

By Z. F. Zhou, X. Y. Zhou, V. G. Papangelakis, Z. D. Jankovic, S. M. Ulyanov, S. N. Lvov

Recently developed flow-through electrochemical techniques (1,2) were employed for measuring pH in high concentration aqueous solutions and geothermal brines. The pH values of (1) 5.0 mol kg-1 NaCl + x mol kg-1 HCl, (2) 3.0 mol kg-1 of NaCl + 0.5 mol kg -1 of KCl + 1.0 mol kg-1 of CaCl2 + x mol kg-1 HCl (x < 0.1 mol kg-1), and (3) mixtures of Al2(SO4)3-H2SO4-H2O, MgSO4-H2SO4-H2O, and NiSO4-H2SO4-H2O solutions have been measured at temperatures from 100 to 280°C. The obtained experimental data and their thermodynamic analysis demonstrated that the electrochemical system can be used for on-line pH monitoring of high concentration aqueous solutions with an accuracy of ±0.1-0.3 pH units over a wide range of temperatures. Greater deviation exists in real laterite leach solution measurements due to in situ precipitation of Na-alunite. The system is excellent for research and process development work. Further work is needed to ensure robust operation under pressure leach conditions of laterites.

Jan 1, 2004

By W H. Poole, E. R. W. Neale

A new style of tectonic map based on age of folding has been prepared for the Canadian Appalachian region as part of the Tectonic Map of Canada Project. This style of map pro-vides a clearer picture of the tectonic history of the region than any meth-od hitherto attempted. Precambrian blocks that were relatively unaffected by Palaeozoic de-formation are distinguished on the Great Northern Peninsula and in the Conception Bay region of Newfound-land. K/ A age determinations suggest that these blocks were intruded and metamorphosed during Grenville orogeny. Other Grenville-like rocks, on Cape Breton Island and in New Brunswick, were more actively involved in subsequent Palaeozoic orogeny. Taconic orogeny, the first phase of Palaeozoic deformation, took place in Middle and/or Late Ordovician time and was accompanied by intrusion of ultrabasic rocks. Evidence of the -

Jan 1, 1961

The Daly-Judge Tunnel, begun in 1887 to drain mine workings, is now a source of potable water for the Municipality of Park City. The water is exceptionally clean; however, when roof falls occur, suspended solids levels become too high and water from the tunnel cannot be used in the treatment plant. In 2001, the tunnel was inspected and rehabilitated to ensure that the water supply for the 2002 Winter Olympic Games would be uninterrupted. Twenty-five timber tunnel sets were removed, and 86 steel sets were installed. Timber lagging was installed or replaced over about 230 m (750 ft) of tunnel length.

Jan 1, 2006

By Jason Berenyi

Presentation Overview ? What is Potash? ? Where are the potash deposits? ? Current potash mines ? production, capacity and planned upgrades ? Saskatchewan Saskatchewan?s Potash Production Potential s ? Current Status of Potash Exploration ? Increasing Demand for Potash ? Saskatchewan global role

May 1, 2009

By J. R. Donald, K. Scholey

"Nickel has been mined and processed from the Sudbury basin for over 100 years. During this period, the process has evolved into what is one of the largest and most complex mining and metallurgical facilities in the world. This paper will describe the geology and mining of the Sudbury basin as well as the Copper Cliff metallurgical flowsheet circa 2005, including:•,Clarabelle Mill,•,The flash smelting furnaces,•,The bulk converters,•,Matte casting, separation, and processing•,The carbonyl refineries•,Carbonyl residue processing•,Copper processing•,Sulphur productsThe challenges of today and the opportunities for the future are discussed."

Jan 1, 2005

By P. Pal Roy, R. B. Singh

"This paper focuses on a number of interesting results to establish the theory and principle of air-deck blasting. It also gives the mechanism of breakage that takes place in air-deck blasting under varying charge load conditions. With these aspects in mind, the mine management can implement this up-coming technology to enhance safety and higher productivity. IntroductionThe method of air-decking has become an increasingly popular technique in production and presplit blasting. In the blasthole, an explosive column is combined with an airchamber. The main aim of the technique is to control breakage through effective distribution of explosive energy and thereby enhance uniform rock fragmentation. An air column lowers the initial pressure of the explosive products and simultaneously increases the time of interaction for the detonation front with the surrounding rock, which enhances rock breakage.To study air-deck blasting, CMRI initially conducted experiments using indigenously developed, low-cost wooden spacers of different sizes and strengths. Air-deck blasting was first tried using these spacers in 1993 at Jambad OCP, ECL and Chasnalla OCP, IISCO. The experiments were extended in 1994 at Bermo Mine, DVC. The results were subsequently published by Pal Roy et al., in 1995. It is worth mentioning that the performance of air-deck blasting during this period was only compared with conventional blasting practices without going into detail of the theory behind the process."

Jan 1, 2001

By D. Ortiz, J. R. Frias, E. D. Mast, J. J. Fañas

Falconbridge Dominicana (Falcondo) has operated an integrated tpy nickel laterite mine and ferro-nickel processing plant since 1972 in the Dominican Republic. The operation includes mining, a processing plant, an oil refinery, and a power plant. Falcondo has improved process efficiency over the years via modernisation and better understanding of the process. The present business environment of high fuel prices and high nickel prices present a challenge and an opportunity to Falcondo&apos;s operation. This paper gives an update of Falcondo&apos;s process, improvements in energy consumption, factors affecting energy consumption and how Falcondo is facing up to the current business environment.

Jan 1, 2005

By Evelynn Stirling

"The paper/presentation will review the evolution of diesel technology from older diesel engines (1990 vintage) through to the latest technology as a result of the ever changing emissions regulations. It will encompass the EPA Tier levels as well as the latest Euro Stage V emissions. The next step with technology will be to address the CO2 emissions, which translates to improving fuel efficiencies of the product as well as other technologies like battery electric, hybrid and fuel cells. As technology progresses it also becomes important to improve connective diagnostic systems to support maintenance practices and improve efficiencies. What will also be presented will be the key emissions changes to the different gaseous and particle mass elements as the products have transitioned from the EPA Tier 3 through to Tier 4 Final regulations. Offering a range of different technologies to the underground mining market matters as not all pieces of equipment will perform optimally due to its duty cycle and application. INTRODUCTION Rudolf Diesel built his first well-known prototype of the high-compression engine in 1897. Since that time, the diesel engine has evolved into one of the world’s most capable and reliable forms of power generation. Diesel engines can be found in a wide variety of vehicles and equipment, powering everything from agriculture and construction equipment to power generators and marine vessels. In the early days the emissions from diesels was very poor and extensive work has been accomplished over the decades to make the product more environmentally friendly. This is more important in underground mining where the space is limited and ventilation is expensive and challenging. DISCUSSION The key driver of the development of diesel technology is the legislation globally around engine emissions. The emission level requirements over the years has forced diesel engine manufacturers to build a deep technical understanding of the system and how to innovate and optimize key elements of the engine. Cummins expertise has been built over the years as the diesel engine has evolved from a relatively simple mechanical engine to an electronic system with advanced air handling, fuel system, after treatment, and controls. Cummins has also continued to expand into systems beyond diesel, including natural gas. Many new components have been added to diesel engines to reduce emissions while improving fuel efficiency and reliability and, at the same time, reduce the total cost of ownership to the customer."

Jan 1, 2019

By David Nicholls

?Overview of New Afton ?Reserves and Resources ?Geology and Mineralization ?Exploration ?Capital Project Development to Date ?Mine Development ?Processing ?Construction ?LOM ?Health, Safety, Environment and Social Responsibility Overview of New Afton ?Fully owned by New Gold Inc ?Large gold-copper porphyry deposit, amenable to block cave mining, production commencing in 2012 -1 million ounce gold reserve -1 billion pound copper reserve -Estimated 13 year mine life ?Low operating cost ?Estimated capital expenditure requirements -Spend to date ?US$200million -Remaining to be spent ?US$400milllion ?Robust economics ?Excellent location and infrastructure ?Significant cash flow contributor for the Company

May 1, 2010

By Jack G. Hazan

The Critical Path Method is the modern scientific answer for solving the planning and scheduling problems inherent in today&apos;s complex projects. With this method, nothing is left to chance. All resources are controlled and kept to the minimum. The various phases are properly planned and strategically determined. Optimum conditions are evaluated for the most economical and fastest way to complete a definite project. The method must be fully understood and implemented with positive data and continuous feedback to obtain the best results. This paper covers the various aspects of the Critical Path Method and mentions some of its applications in the mining and metallurgical fields. T 0 progress to a higher state of human welfare necessarily involves sacrifices. The greatest sacrifice is to relinquish social freedom in favour of economic freedom. In the old days, for example, a cobbler was free to work at whatever time of the day he chose; today, he can&apos;t. He is now forced to adapt himself to environment and to work at stand-

Jan 1, 1965

By A. D. Dalvi

Economics, Resources, Environment and Technology are the major driving forces in the base metals industry. However, these factors are intertwined and together will propel the industry in the future. The demand for metals has grown with economic expansion, between 2 to 4 % p.a. The current growth cycle has been driven by economic expansion in China where the demand for base metals has risen from - 7 % of the world demand in the 90&apos;s to - 25 % of world demand today, and rising. Base metals are commodities and their demand and price are cyclical. Historically metal prices have declined in constant dollars, forcing the industry to reduce costs, increase productivity and increase the scale of operation for economies of scale. Due to resource depletion and capacity expansion the industry is driven to expand its reserve and resource base. However, in the case of sulphide deposits of copper and nickel it appears to be a losing battle. For nickel the laterites represent a vast source at this time. Their development requires development of new technologies to make these resources economic. Emission reduction is being increasingly mandated in most jurisdictions with all governments enacting progressively more stringent regulations. The industry has been responding with technological innovation. With the Kyoto protocol there is a push to reduce energy intensity in metal production. Technological innovation is driven by all the other factors and is leading to novel ways of doing exploration, mining and processing, that would maximize resource delineation and utilization, reduce costs, increase productivity, reduce energy consumption, maximize asset utilization and reduce environmental affects. Development of alternative technologies such as Pressure Acid Leach of laterite for nickel, bio-leaching, heap leaching, SX-EW etc are being adopted to achieve the aims of the industry.

Jan 1, 2005

By M. Souley, G. Armand, M. Ghoreychi, D. Seyedi, J. -B. Kazmierczak

"An anisotropic constitutive model is proposed in this paper accounting for both structural anisotropy and induced anisotropic plasticity. It is assumed that the rock is composed of a matrix and of potential planes of weakness. The matrix is assumed to be linear, transversely isotropic and the plasticity is described by a non linear yield function where the parameters are deduced from the nonlinear Hoek-Brown envelopes in pre- and post-peak, and derived from the laboratory characterization. A non-associated flow rule is used with a distinction between compression and extensional stress paths, as well as the absence of volumetric strain beyond large plastic distortion.The planes of weakness are considered as known a priori or assumed to be oriented perpendicular to the direction of the current minor principal stress. An elastic-perfectly plastic behavior according to the Mohr-Coulomb criterion is assumed in the planes of weakness; while the elastic part is considered as linear and transversely isotropic.Finally, the proposed model was implemented in FLAC3D and used to simulate triaxial compressions to provide a verification of the implementation. The applicability of the implemented model to reproduce damage (pre-peak) and/or failure developments around a circular opening is checked. The GCS drift, one of the mine-by experiments set up at the main level of the Meuse/Haute-Marne Underground Research Laboratory, is selected for this first application."

Jan 1, 2015

By J. A. Allan

The utilization of natural deposits of salt is one of the oldest industries in Alberta. In 1820, Sir James Richardson visited Salt river, and in the same year D. W. Harmon states chat "clown Slave river, there are several places, where almost any quantity of excellent dean white salt may be taken, with as much ease as sand along the seashore. From these places the greater part of the northwest is supplied with this valuable article". This reference is to the salt chat occurs around springs on Salt river at the northern boundary of the Province. This and other occurrences will be described later in this paper. It is not on account of the development of salt and gypsum in Alberta chat this paper has been prepared, but rather to draw attention to the widespread distribution of salt-bearing and gypsum-bearing rocks, and to the stratigraphic importance of these rocks . The origin of the deposits of salt, gypsum, anhydrite, and dolomite is discussed, and the economic significance of these minerals is considered. There is no salt production reported from Alberta in 1928.

Jan 1, 1929

By P. R. Clark, M. D. Gleghorn

"IntroductionAt TransAlta Utilities Corporation&apos;s Highvale Mine, located west of Edmonton, Alberta (Fig. I and 2), dragline stripping has proved to be a practical and economical method of overburden removal and future plans have been based upon the continued use of draglines (Fig. 3) as the major stripping equipment (Williams, 1979, Nikols et al., 1986). However, long range planning has shown that the capacity of draglines alone will be exceeded in the early 1990s as mining progresses into deeper overburden cover (Tapics, 1983). Strip ratios will increase from I.3 bank m!/ t of coal in 1985to 4.5 bank m3 / t in 1995. During this period the depth of overburden will increase substantially and the areas to be mined will be characterized by weak soils including glacially displaced overburden. This increased overburden depth in relatively weak soils will make it impractical to _continue side casting by draglines without prestripping in advance. In 1983, a major investigation was initiated to determine what additional overburden removal equipment was appropriate to the Highvale operations, and recognizing the long delivery times of this major equipment. when it would be required. This paper describes studies and tests which were undertaken in 1983 and 1984 to select prestripping methods and equipment for the future operation of the mine.Previous planning studies have shown that with the current burn schedule and with the economies of progressing from low cover to high cover, as has been practiced in the past, overburden volumes will exceed the capacity of the existing draglines in the early 1990s (Fig. 4). These previous studies had placed reliance on (I tandem dragline operation for future overburden removal requirements up to a depth of 45 m throughout the Highvale Mine. New drilling together with the associated geotechnical studies and some detailed planning on the practicality of using tandem draglines, created concerns about their universal application. Even without considering geotechnical conditions there was a depth limitation to tandem dragJines and substantial prestripping would be required to achieve the ultimate depths."

Jan 1, 1987

By Subrata Dutta

Sindesar Khurd Mine is situated in Rajasthan, India, and operated by Hindustan Zinc Ltd, under Vedanta Group. The base metal mine is high in reserves of Lead, Zinc and silver and has been producing since 2007 with initial production of 0.3 mtpa. Recently the mine has gained prominence as a base metal underground mine in introduction of latest mining techniques and achieving high production at lowest costs. The promising Lead-Zinc reserves of Sindesar Khurd Mine (SKM) and high-tech exploration adopted by Hindustan Zinc Ltd (HZL), (Vedanta Group), raising the reserves and resources from a meager 9 Mt (1997) to 81 Mt (2012), has prompted HZL management to ramp up the mine production from 0.3 mtpa (2006-07) to 2 mtpa by 2013-14 with ambitious plans to reach 3.5mtpa subsequently (presently largest underground metal mine in India). The complete trackless system underground mine, recently equipped with latest leaky feeder communication system (unique in India), utilize modern drilling, mucking and hauling equipment aided with various utility/service vehicles. Excavation optimization and quality recovery maximization from the open and post filled stoping methods, continual expert analysis and feedback from International consultants like AMC (Australia) and SRK (UK), and involvement of renowned bodies in management excellence, have lead the mine towards highest productivity and lowest mine operating cost, earning the mine a prominent place in the global base metal industry. The paper deals with how the various challenges in mine planning and designing, mine development, operator skill, equipment introduction and maintenance, expertise availability, provide training and exposure to officials, prompt and effective communication/service, control of ground vibrations, maintain ventilation standards etc are faced in attaining high operational excellence and thus attain a record mine output/man shift (OMS) of 14 ton/man shift with targets to reach 20 ton/man /shift. Scientific designing using 2D/3D numerical mine-modeling techniques, faster stope sequencing with introduction of paste filling ( first time in India),latest leaky feeder communication system, control ground vibration to stringent standards using electronic delay system, faster raising techniques using raise borers to enhance development and ventilation, cavity scanners to monitor large stope voids, fast shaft sinking at 100 m/month(Chinese expertise) and maintaining adequate ventilation with close software monitoring are some of the highlights discussed in the paper towards achieving the targets.

Aug 1, 2013