Search Documents

By M. R. Tek, L. K. Thomas, D. L. Katz

Threshold displacement pressures are needed to determine how much overpressure can be used in storing natural gas. An experimental technique for determining threshold pressures by displacing water with gas from samples saturated with water is presented. Threshold pressures for eight low permeability samples were measured. Threshold pressure data obtained in this work, plus data on higher permeability samples reported in the literature, are correlated with porosity, permeability, surface tension and formation resistivity factor. Mercury injection pressures also were measured and correlated with air-water threshold pressures. Threshold pressures were found to be independent of time. An aerial photograph of gas emerging from the top of a core shortly alter its threshold pressure has been exceeded shows that the gas bubbles are uniformly distributed across the face of the core. Channeling will occur, however, when an increased gas phase permeability is reached, A porous medium can be re resealed alter its threshold pressure has been reached, provided it has not been desaturated below a fixed saturation. Its new threshold pressure will be lower than when the sample is 100 percent saturated with water. INTRODUCTION The degree of overpressure in excess of the discovery pressure that a gas storage reservoir can withstand is determined by the ability of its caprock to contain gas, providing the pressure does not exceed the structural limit of the reservoir. The retention of gas in a reservoir by a caprock saturated with water is a result of the capillary forces acting at the gas water interface. Without the presence of water in a caprock, gas would leak out of the reservoir at a rate determined by the permeability of the caprock to gas. The ability of a caprock to contain gas is expressed in terms of its threshold displacement pressure, which is defined as the minimum pressure needed to initiate the displacement of a wetting phase by a nonwetting phase from a porous medium 100 percent saturated with the wetting phase. The gas industry must be able to predict how much "overpressure" a gas reservoir can withstand before leakage occurs by gas displacing water from caprock overlying the reservoir. This is of economic importance since the storage capacity of a gas reservoir is proportional to its pressure. The discovery pressure for most reservoirs is found between the upper and lower limits1 shown in Fig. 1. Discovery pressures in excess of their hydraulic pressure gradient are attributed to the compaction of an isolated shale formation by the overburden.2.3 The lower limit of 0.433 psi/ft corresponds to the weight of the overburden, the gradient of the rock itself. Somewhere between

Jan 1, 1969

By R. F. Nielsen, R. G. Bentsen

Jan 1, 1966

By K. P. Fournier

This report describes work on the problem of predicting oil recovery from a reservoir into which water is injected at a temperature higher than the reservoir temperature, taking into account effects of vis cosity-ratio reduction, heat loss and thermal expansion. It includes the derivation of the equations involved, the finite difference equations used to solve the partial differential equation which models the system, and the results obtained using the IBM 1620 and 7090-1401 computers. Figures and tables show present results of this study of recovery as a function of reservoir thickness and injection rate. For a possible reservoir hot water flood in which 1,000 BWPD at 250F are injected, an additional 5 per cent recovery of oil in place in a swept 1,000-ft-radius reservoir is predicted after injection of one pore volume of water. INTRODUCTION The problem of predicting oil recovery from the injection of hot water has been discussed by several researchers. l-6,19 In no case has the problem of predicting heat losses been rigorously incorporated into the recovery and displacement calculation problem. Willman et al. describe an approximate method of such treatment. 1 The calculation of heat losses in a reservoir and the corresponding temperature distribution while injecting a hot fluid has been attempted by several authors.7'8 In this report a method is presented to numerically predict the oil displacement by hot water in a radial system, taking into account the heat losses to adjacent strata, changes in viscosity ratio with temperature and the thermal-expansion effect for both oil and water. DERIVATION OF BASIC EQUATIONS We start with the familiar Buckley-Leverettg equation for a radial system:* This is sometimes referred to as the Lagrangian form of the displacement equation. If the injection water is at some temperature Ti which is above reservoir temperature TR, then lw, the flowing fraction which is water, is a function of both water saturation and fluid temperature at any given time and position in the reservoir. The temperature dependence of lw results from the temperature dependence of the viscosity ratio µo/µm of which lw is a function. Thus:

Jan 1, 1966

By Jerome F. Kuzmick

Condusions. From the work on aluminum powder, the following general con clusions can bc drawn: I. The physical properties of aluminum compacts, such as density. strength and ductility, increase with increasing pressure, up to the practicable pressure limits. 2. Good properties ill aluminum con pacts can be secured only by the use of high pressures, because it is neccssary to rupture the refractory oxide film on aluminum powder. 3. Considerable softening of the specimens occurs upon sintering. regardlers of the pressure used. General Conclusions 1. For relatively short-time sintering. molding pressure is a very important factor in the final physical properties of the sintered specimens. 2. The effect of pressure. is difierent for each metal, so that few general rules can be drawn that would apply to all metals. 3. In many cases, fur a particular metal powder and sintering temperature there is a critical pressure at which the best physical properties can be obtained. 4. The principles of cold work and in nealing and their effect on grain structure applied to massive metal also holds true for sintered metals. 5. Particle size, at least for electrolytic iron powder, does not have a. great effect on ultimate grain six. DISCUSSION [E. E, Schumacher presiding V.. V. Crane. *—I was particularly impressed with Dr. Kuzmick's work on tin IF not the illustration, particularly the Second one. a very good illustraition of hot preessing. in that

Jan 1, 1945

Map

Jan 1, 1941

By Ivan B. Cutler, Milton E. Wadsworth

Coprecipitation of anionic and cationic polyelectrolytes has been applied to floccula-tion of several mineral systems. Results obtained in a study of the flocculation of kaolinite and hematite suspensions of polycationic and polyanionic electrolytes are presented. Greatly increased settling rates were observed following precipitation of positive and negative polyelectrolytes on the surface of finely divided minerals in aqueous suspension. The ratios of polycationic to polyanionic electrolytes required to produce maximum sedimentation have been shown to correspond closely with the equivalence points obtained by light scattering studies of systems containing the positive and negative polyelectrolytes by themselves. DISPERSION of colloids has been of interest to surface chemists for many years. Flocculation studies have been employed to evaluate the limits of colloid stability. In water suspensions, colloids become unstable and flocculate when the 5 potential, the potential of the kinetic solvation sheath, falls to a value at which van der Waals forces may act to draw the particles together. This may happen through an adjustment of the pH of the suspension or by addition of a salt. Optimum conditions for rapid formation of large flocs are found in the region of minimum < potential. In addition to these well known considerations, colloids in water suspensions are known to be flocculated by certain large organic macromolecules. These polyelectrolytes in some cases minimize the 5 potential and in other instances increase the attractive forces by supplying sites for hydrogen bonding.&apos; Use of organic polyelectrolytes in flocculation of mineral colloids has increased rapidly in recent years. These materials are now recognized as indispensable aids to fluid-solid separations in many extractive metallurgical operations. They have been found to increase both the settling rate in thickeners and the filtration rate of filters. In the elucidation of the characteristics of these organic reagents as floc-culants in this laboratory, it was discovered that interaction of certain polyelectrolytes had a surprisingly good effect on flocculation of mineral colloids. Experimental Procedure: The anionic flocculants used in this study were Lytron 886 and 887, produced by Monsanto Chemical Co. Both reagents are copolymers of vinyl acetate and maleic anhydride. Lime is added to Lytron 886, whereas Lytron 887 is all organic. These reagents possess two carboxyl groups for each acetate group and are therefore anionic in character. The cationic reagents used were the Peter Cooper Co. 1-X and 2-X glues. The structures are not definitely known, but the re- agents are amines and are cationic in character. The glues were prepared in the chrome-alum form. Both types of reagents may be classified as polyelectrolytes in that they are high molecular weight polymers and ionize in water. All data presented are in terms of sedimentation rate, measured in 250-ml glass-stoppered graduated cylinders. With suitable precautions such measurements are fairly reproducible and provide a sensitive means for selecting important parameters such as PH, reagent concentration, and floc size and density. Agitation was standardized with five complete end over end cycles of the suspensions in the stoppered graduated cylinders.

Jan 1, 1957

[Separates of all the Technical Publications published in 1928 are available at Institute headquarters. All the papers are on file in public, university and technical libraries, and when so indicated in the list, may be found either in the TRANSACTIONS or in the special volumes issued by the Institute] . METAL MINING TECHNICAL TRANS. PUBLI- TITLE AUTHOR MEETING VOLUME CATION AND PAGE* No. 50 .The Eötvös Torsion Balance D. C. Barton New York Method of Mapping Geologic Feb., 1928 Structure 52 A Cartographic Correction for the C. A. Heiland New York Eötvös Torsion Balance Feb., 1928 61. Liquid-oxygen Blasting at Chuqui- H. C. Schultz, New York camata, Chile F. K. Middleton Hunter Feb., 1928 76, 108, 123 64 Working Methods of Practical Geo- Hans Haalck New York physics Feb., 1928 65 Experiments with Eötvös Torsion P. W. George New York Balance in the Tri-State Zinc and Feb., 1928 Lead District 74 Gravity Surveying in Great Britain H. Shaw New York Feb., 1928 75 The Computation of Eötvös Gravity E. Lancaster-Jones New York Effects Feb., 1928 82 Earth-resistivity Measurements in W. 0. Hotchkiss, New York the Lake Superior Copper Country W. J. Rooney, Feb., 1928 James Fisher 83 Mining Methods and Records at the Roy W. Moore New York 76, 56, 90 United Eastern Mine Feb., 1928 98 Recent Results in Electrical Pros- Hans Lundberg New York

Jan 1, 1928

By H.A. Bedworth

AlloTs of copper and silicon have been known for one hundred years or more but the commercial development of this type of alloy has taken place during the past few years. In 1905, Sperry l proposed the use of copper-silicon alloys for springs and other purposes for which copper-tin bronzes were used. Some attention was given to this proposal at the time but no one succeeded in producing a practical alloy containing more than a fraction of a per cent. of silicon. The equilibrium relations of the copper-silicon system were studied first by Rudolfi2 and later by Sanfourche 3 and Corson. 4 The constitution of the system has also been recently investigated by Matuyama, 5 and in the laboratories of the American Brass Co. by Smith. 6 Some of the physical properties of the copper-silicon alloys have been investigated by Norbury7 and by Geiss and Van Liempt.8 Summarizing the results of various investigators of the constitution of copper-silicon alloys, the solubility reaches its maximium value, 6.7 per cent. silicon, between 721" and &apos;782" C. At 852" (1. the solubility is 5.25 per cent., while at 400" C. it is only 4.1 per cent. silicon. The copper-silicon alloy begins to get so hard at about 3 per cent, silicon that it is difficult to manage. It was found by Jacobs that the addition of manganese to this alloy considerably improved the working

Jan 1, 1929

By H. A. Bedworth

AlloTs of copper and silicon have been known for one hundred years or more but the commercial development of this type of alloy has taken place during the past few years. In 1905, Sperry l proposed the use of copper-silicon alloys for springs and other purposes for which copper-tin bronzes were used. Some attention was given to this proposal at the time but no one succeeded in producing a practical alloy containing more than a fraction of a per cent. of silicon. The equilibrium relations of the copper-silicon system were studied first by Rudolfi2 and later by Sanfourche 3 and Corson. 4 The constitution of the system has also been recently investigated by Matuyama, 5 and in the laboratories of the American Brass Co. by Smith. 6 Some of the physical properties of the copper-silicon alloys have been investigated by Norbury7 and by Geiss and Van Liempt.8 Summarizing the results of various investigators of the constitution of copper-silicon alloys, the solubility reaches its maximium value, 6.7 per cent. silicon, between 721" and &apos;782" C. At 852" (1. the solubility is 5.25 per cent., while at 400" C. it is only 4.1 per cent. silicon. The copper-silicon alloy begins to get so hard at about 3 per cent, silicon that it is difficult to manage. It was found by Jacobs that the addition of manganese to this alloy considerably improved the working

Jan 1, 1929

By E. H. Jr. Dix

THE use of magnesium as an alloying element in aluminum alloys has been limited, in general, to comparatively small quantities. In duralumin-type, strong-aluminum alloys, magnesium is present to the extent of ½ to ¾ per cent. and various grades of Magnalite and the "Y" alloy of the National Physical Laboratory of England contain up to 1 1/2 per cent. In this country small quantities of aluminum alloy sheet containing 4 per cent. magnesium are produced commercially. All commercial aluminum contains sufficient silicon to convert a portion of the magnesium added to the compound Mg2Si. It is well known that the solubility of both magnesium and magnesium-silicide decrease with decrease in temperature. It is, therefore, impossible to separate the age-hardening effect of the magnesium-silicide from that of magnesium, except by the use of aluminum of such high purity that the silicon content is negligible. The present paper is the fifth1, 2,3,4 of a series from the laboratories of the Aluminum Co. of America reporting the results of investigations of the equilibrium relations in aluminum-rich alloys made from the high purity aluminum manufactured by this company .5

Jan 1, 1929

By K. H. Coats, M. H. Terhune

Analysis and example applications have been performed to compare the accuracy and computing speed of alternating-direction explicit and implicit procedures (ADEP and ADIP) in numerical solution of reservoir fluid flow problems. ADIP yields significantly greater accuracy and requires about 60 per cent more computing time than ADEP, not 300 or 500 per cent more as reported elsewhere. l,2 INTRODUCTION Several recent papers 1-3 discuss an alternating-direction explicit difference approximation (ADEP) to the diffusion equation. Example applications of ADEP and ADIP4 were reported to support conclusions that ADEP is comparable in accuracy to ADIP and requires one-fifth to one-third the computing time of ADIP. Applications of ADEP in calculation of two-phase flow in reservoirs was also proposed. 3 This study was performed to compare further the relative merits of ADEP and ADIP in simulation of two-dimensional flow of one and two fluid phases in reservoirs. Since two-phase flow equations are often essentially elliptic rather than parabolic, the efficiency of ADEP in solving the elliptic equation was also examined.

Jan 1, 1967

By S. E. Bretherton

This title introduces the subject I wish to describe to my fellow members, very few of whom, I &apos;hope, have ever had as much trouble with the smelting of ore containing much zinc, either in the lead blast furnace or the matting furnace, as circumstances have forced upon me: First, for several years in Leadville, Colo., after the sulphide ores containing zinc had been developed with greater depth and were sold to the intereats with which I was connected for smelt-ing in the blast furnace for the recovery of the lead, silver, and gold; then, in New Mexico and Arizona, where the principal source of ore supply for our custom smelter was from miners who sent most of their product in the form of concentrates, which we briquetted and smelted in the blast furnace, producing a matte containing copper, silver, and gold, for which we were paid; together with some zinc and lead, which was penalized if in excess of a maximum base set by the refinery to which we sold our copper matte; last, but not least, my experience in Shasta county, Gal., where for the sake of recovering $13 per ton value in copper, silver, and gold, I have smelted ore containing as high as 40 per cent. zinc (the last 18,951 tons smelted averaged 15 3/10 per cent. zinc) which we not only lost, but which it cost us money to lose. After such an experience, and knowing that, instead of being worth only $13 per ton, such 15 per cent. zinc ore should be worth about $30, including zinc at the present market value, the question of recovering the zinc in a profitable manner from such ore became very interesting to me. During several years&apos; time I sent samples, of from 5 to 1,200 lb. each, to be tested by the different best-known zinc-recovery plants, and experimented with several processes proposed by others for the treatment of such ore, with but little encouragement, until I

Jan 1, 1914

By D. M. Davidson, P. F. Kerr

The Permian Cutler Formation in Kane Creek, Utah bears uranium ore in fissure-type vertical veins. This fissure vein formation and its associated host rock bleaching, weak argillic alteration, and base-metal sulfide mineralization along with the development of hydrothermal minerals, a 60 m.y. isotopic Pb/U age, and well-crystallized uraninite&apos;s structural control, give evidence of ore deposition in a hydrothermal environment consistent with Laramide mineralization. Mica polymorph studies indicate first, that temperature during the hydrothermal alteration or subsequent ore deposition did not exceed 200°; hence Cutler deposits are classified telethermal; and secondly, that rock alteration and ore deposition are closely related both in time and space, as is seen in argillic alteration sequence. Ore deposition in an alkaline to slightly acid reducing environment is postulated. Ore textures and mineral associations and distributions also indicate that carbonate complexes may have been transported with the deposing ores. Bleached rock formations are not primary strati-graphic phenomena. Bleaching, or changes in ferric iron content, results from a chemical process involving reduction and conversion of hematite to a soluble aqueous ion. Nearby Chinle bedded deposits (Moss Rack sandstone), containing shale lenses, fossil wood, organic debris and minor fractures, overly the Cutler formation. Chinle ores have a single reported isotopic age of approximately 200 m.y. Their chemical environment is assumed similar to that of the Cutler ores, though slightly more acidic. Two genetic, paradoxically divergent interpretations of the bedded deposits are derived from available spectrographic, petrographic, X-ray and chemical analyses. Kane Springs canyon is located southwest of Moab, Utah, south of the Colorado River and northwest of the Lisbon Valley mining district (Fig. 1). Uranium deposits occur along the northeast flank of a Kane Creek salt anticline where two geologic formations bear ore, the Permian Cutler and the Triassic Chinle. The Cutler deposits&apos; fissure vein formation is an unusual occurrence in the Colorado Plateau. The Chinle deposits appear to be of the normal sedimentary type. Associated with the vein deposits are a number of features, including argillic alteration of sedimentary strata. The minerals of these deposits and their associated features have been studied in detail in a two year program entailing both field and laboratory techniques. STRATIGRAPHY A stratigraphic section of the lithologic units in the Kane Creek area is given in Table I.

Jan 1, 1967

NEW MEMBERS. The following list comprises the names of those persons who became members during the month of April, 1913: BARNES, BLAKESLEE, Min. Engr Burrwood, La. BOYLSTON, HERBERT M., Cons. Met. Engr 26 Abbot Bldg., Cambridge, Mass. BUEHLER, HENRY A., State Geol Rolla, Mo. CASTO, WILLIAM H., JR., Mining Bonanza, Idaho. COHEN, MAXWELL B., Mill Operator Miami, Ariz. EVANS, MILTON R., Shop Draftsman 92 Division St., Kingston, Pa. HARPER, WALTER S., Asst. Treas 42 Broadway, New York, N. Y. JAMES. JAMES S.. Min. Engr Telluride. Colo.

Jan 5, 1913

By A. Moskowitz, L. S. Redmerski

The corrosion resistance of stainless steels can be strongly affected by surface treatments. Changes in corrosion resistance can relate to surface composition, integrity and stability of the passive film, and to surface profile (roughness). Operations producing oxidation at the surface, such as annealing, heat treating, and welding, can result in a chromium-rich scale and a chromium-depleted metal surface. In order to restore full corrosion resistance, chemical or mechanical clean-up techniques must remove not only the oxide, but also a very thin layer of metal. Laboratory and field test studies show that these factors are particularly significant in less highly alloyed steels. Annealing stainless in a reducing atmosphere (bright annealing) avoids chromium depletion, but as-bright-annealed material does not display optimum corrosion resistance in certain environments. Electro passiva-tion can be applied to improve pitting resistance without significantly changing bright surface appearance. Potentiometric studies show that electropassivated material also displays significantly greater resistance to breakdown of passivity in acid solutions. The application of special surface finishes for appearance purposes can affect corrosion resistance. Roughness is a key factor. Samples of related appearance but with different surface profiles can show significant differences in corrosion resistance. Thus nonreflec-tive stainless with a relatively smooth surface produced by a special rolling process is much superior to material chemically etched to a similar low reflectivity. THE corrosion resistance of a stainless steel is affected by other factors in addition to its bulk composition and metallurgical structure. These other factors include those relating to the specific chemical and physical condition of the steel&apos;s surface. This paper will consider certain aspects of surface condition in relation to corrosion resistance. In particular, studies will be described on the effects of oxidation encountered in heat treating or welding operations, of passivation after bright annealing, and of different surface finishes. EFFECTS DUE TO OXIDATION When stainless steels are exposed to high temperature in an oxidizing environment, as in annealing or welding, the oxides formed are relatively rich in chromium. As a consequence of oxidation, the metallic layer directly beneath the scale may be low in chromium to some very thin but finite depth.1"8 Such a change in chromium content could lower the corrosion resistance at the surface, whether or not the oxide layer is removed. Studies were performed relating to the effect of oxidation and chromium depletion produced during annealing and welding on the corrosion resistance of stainless steels. The nominal compositions of steels used in this study and others are given in Table I. A) Annealing Studies on 17 pet Cr Steels. 1) Effects of Pickling Treatments. Studies were performed to investigate the corrosion resistance of air annealed type 430 stainless as a function of the amount of electrolytic pickling after annealing. The material used in this study had been air annealed and electrolytically pickled in the mill. All scale had been removed, and yet the material showed unusually poor corrosion resistance. Laboratory electrolytic pickling studies were performed to determine whether additional metal removal from the surface would improve corrosion resistance. Electrolytic pickling was performed in a sulfuric acid bath using various conditions of bath acidity, temperature, time, and current density. The samples were then rated for corrosion resistance in a ferric chloride spot test. For this spot test, a solution was prepared by dissolving 10 g of FeCl3 . 6H2O, 5 g of NaCl, and 2.5 ml of concentrated HC1 in 200 ml of water. An area on a specimen was cleaned and a drop of test solution was placed on the prepared area. After 5 min, the drop was rinsed off and the area wiped dry. The spot was then rated between 1 and 5 by visual comparison with standard spots. The numerical rating of the standard spots can be described as follows: 1—No clouding of surface; 2—very slight clouding of surface; 3—slight clouding of surface; 4—moderate clouding of surface; 5—strong clouding of surface. A rating of 1 or 2 was considered to have passed the test, a rating of 4 or 5 represented failure, and a rating of 3 was considered borderline. The severity of etching in this test has been related to the actual chromium content at the surface.4 Etching (clouding) occurs on type 430 stainless (rating of 4 to 5) when the surface chromium content is 14 pct or less. The effects of current density and retention time when electrolytically repickling this material in 6 pct sulfuric acid are shown in Fig. 1. Increasing the cur-rent density or retention time improved corrosion resistance as measured by the spot test. Similarly, increasing acid concentration of the bath or bath tem-perature was found to improve corrosion resistance. The conditions making for improved spot ratings resulted in increased metal removal, regardless of specific pickling conditions used, Fig. 2.

Jan 1, 1970

By F. W. Jessen, C. C. Patton

Adsorbed films were formed on polished stainless steel specimens from dilute benzene solutions of two crude oil distillation residua. Although the two residua were extremely dissimilar in composition, contact angle measurements showed that the two films increased the wettability of the steel specimens to oil by equal amounts. Furthermore, the wettability of the films was essentially unaffected by the desorption techniques used. Paraffin deposits were formed from heptane-wax solutions on the same stainless steel specimens. These deposits definitely adhered to the surface. Presence of an adsorbed crude oil film on the metal surface increased its free surface energy and resulted in increased deposition of paraffin. The addition to the heptane - wax solution of small amounts of the same distillation residua that were used to form the adsorbed films resulted in decreased cohesive strength in the deposits formed, which resulted in decreased deposition. The presence of a crude oil fraction both in the solution and as a preadsorbed film eliminated the adherence of a deposit of any kind. A mechanism of deposition is proposed which explains the results obtained. INTRODUCTION The natural formation of any predominantly organic accumulation in oilwell tubing, surface flow lines or other production and storage facilities is called a paraffin deposit. These deposits restrict the production of crude oil, causing a substantial increase in production costs because of decreased flow capacity, expense for periodic deposit removal and unproductive downtime. The conditions under which such deposits form, their physical characteristics and the nature and severity of the problem created are extremely varied. Over the past several years, much progress has been made in developing and utilizing methods to remove accumulated paraffin deposition. However, like so many other problems, the basic stumbling block appears to be a lack of understanding of the fundamental mechanism involved in the formation of such deposits. Crude petroleum is known to contain considerable quantities of polar, surface active substances which Doddl has shown to be present at the oil-water interface. Denekas, Mattax and Davis2 observed that the wettability of reservoir rocks was drastically altered by exposure to crude oil fractions; and Zisman, et a1.3 showed that the nature of the compounds adsorbed on a surface would determine its wettability characteristics. Cole and Jessen4 and Ehrig5showed that surface wettability can have a profound effect on the magnitude of paraffin deposition, and Parks6 demonstrated chat the presence of certain adsorbed films on a metal surface would reduce the adherence of paraffin to that surface. Zisman7 has since advanced the theory that the conditions for adhesion are the same as for wetting. Therefore, it was felt that there was adequate evidence to support the supposition that adsorption of compounds from a crude oil might play an important part in paraffin deposition. ADSORPTION-WETTABILITY EXPERIMENTS Initial experiments were conducted to determine the effects of adsorption from solution of crude oil residua on the wettability of a polished stainless steel surface. Distillation residua with initial atmospheric boiling points of 700F were used in preference to the whole crudes in order to concentrate on the molecular weight range of interest, and to eliminate the possibility of composition change due to evaporation of the light ends. Also, these high boiling materials would be expected to be adsorbed from the whole oil in preference to similar compounds of lower molecular weight.

Jan 1, 1966

By Robert S. Nichols

Fording Coal Limited&apos;s mine in the Rocky Mountains near Elkford, B.C. has produced 21.8 million clean tonnes of metallurgical coal from 1971 to 1980, inclusive. This production has come from several pit areas and required the removal of 149.1 million bank cubic meters of waste rock and overburden by truck-shovel and dragline operations. Waste dumps from 30m to 200m in height have been successfully constructed on natural slopes, generally between 10° and 26°. Design considerations for the dumps include foundation and soil conditions, natural slope angles and containment of weak overburden or rehandle materials. Dump control is maintained by monitoring the crest and the face of an active dump area. Crest movement is measured by extensometers locally termed "Spoil Monitors". When crest movement rates progressively increase above normal, dumping operations are temporarily relocated. Some unstable conditions and mass failures have occurred as the result of natural foundation slopes being in excess of 26°, failure of weak water saturated foundation soils or weak material being placed on the dump.

Jan 1, 1983

By Rudolph Emmel

THE mines operated by the South American Development Co. are located in the Zaruma mining district of southwestern Ecuador. They are near the old mining town of Zaruma, which is the only important city in the canton of the same name. The district is situated in the upper end of a valley lying between two spurs of the Cordillera, one of which may be considered the Coast Range and the other an intermediate range. The mining camp proper, known as Portovelo, and the plant are 2.4 km. south of Zaruma, on the north bank of the Amarillo River, a tributary of the Tumbes River, which flows southwestward through Peru to the Pacific. Portovelo is difficult of access; it is reached from Guayaquil by means of river steamers and muleback. Embarking at Guayaquil, the route is down the Guayas River, across the Jambeli Canal, and up the Santa Rosa River to Santa Rosa, a distance of 177 km. From Santa Rosa, the road or trail follows the Santa Rosa River, then across the summit of the Coast Range into Portovelo, a distance of 74 km.-a two-day trip on muleback. The mining property of the South American Development Co. comprises 297 lode claims and 142 placer claims. The combined lode claims cover an area, roughly rectangular in shape, 9000 m. long from north to south by 4000 m. wide; the northern edge of the rectangle is about 3000 m. north of the central plaza of Zaruma. Mineral lands in Ecuador are held by virtue of an annual tax per claim paid to the central government, no surface rights being included.

Jan 1, 1925

By K. E. Gray, M. S. Seth

In Part I of this work,1 equations of elasticity were formulated for transversely isotropic, axisymmetric, homogeneous, porous media exhibiting pore fluid pressure. Equations of elasticity and the thermal analogy method were used to determine transient horizontal, tangential, and vertical stresses and radial displacement in a semi-infinite cylindrical region when either a constant rate of pressure or a constant rate of flow is maintained at the wellbore. In this paper, the approach presented earlier is extended to finite reservoirs for the cases of (1) steady-state flow, (2) constant pressures at the well bore and outer boundary and (3) constant pressure at the wellbore and no flow at the outer boundary. Results of this work show that radial and tangential stress gradients are high near the wellbore but diminish rapidt; away from the well; the vertical stress gradient behaves in the same way but is less severe. Radial stresses are compressive or neutral, whereas tangential and vertical stresses may be tensile, neutral or com-pressive, depending upon the boundary conditions, the physical Properties of the system and the radial distance involved (vertical stresses are always compressive in an unbounded system1. For constant boundary pressures, both radial and tangential stresses increase with time whereas they both decrease for a closed outer boundary and constant pressure at the wellbore. The vertical stress decreases with time for both systems. For steady-state systems, radial displacement may be positive or negative, depending upon the dimensions of the system, the pressure differential and the porosity. Radial displacement may be positive or negative for a closed outer boundary but is positive for constant pressures at both boundaries. INTRODUCTION The importance, utility and complexity of a realistic appraisal of the stress state at and local to a wellbore were indicated in Part I. In this paper the analytical approach presented earlier is extended to finite, cylindrical reservoir geometry for the cases of (1) steady-state flow, (2) constant pressures at wellbore and outer boundary and (3) constant pressure at the wellbore and no flow at the outer boundary. Other than the outer boundary of the reservoir being finite, the physical system and assumptions pertinent thereto are the same as before. The reader may wish to review the mathematical development through Eq. 49 of Part I before proceeding here. SOLUTION FOR GENERAL BOUNDARY CONDITIONS THERMAL STRESSES AND DISPLACEMENTS Since normal stresses do not exist at the free boundaries of a system subjected to thermal stresses, the boundary conditions are

Jan 1, 1969

By Job Goostray

IN THIS paper, as in so many other discussions of historical nature, there is little chance for original material and much has had to be rewritten from older papers, documents, accounts, reports, and the like, some of which are of doubtful authorship or contain conflicting statistics. Fully aware of these little historical pitfalls, the authors have tried to quote the origin where possible, and also to seek further confirmation when the statement warranted it, but cannot assume responsibility for certain facts and dates. The Encyclopedia Britannica was frequently consulted. The authors wish to acknowledge assistance from MacKintosh-Hemphill Co.-formerly the Fort Pitt Works-and also from officials of the Watertown Arsenal who loaned valuable books and gave much necessary information. They are particularly indebted to Colonel Dixon of that institution. The data on modern guns were furnished by Mr. F. Brauer of the Watertown Arsenal; Mr. H. S. Chaffee assisted by obtaining records and data of work carried on by the Builders&apos; Iron Foundry of Providence, R. I.

Jan 3, 1925