Search Documents

By W. A. Ver Wiebe

Spurred on by the very high demands for new crude supplies resulting from World War 11, the oil men of Kansas strained every effort in 1943 to find as many new pools as possible. In all, 1761 test wells were drilled, ,of which 895 were successful in finding new oil supplies and 32 in finding new gas supplies. The total number of wildcat wells drilled in Kansas was 577, including the so-called "extension wildcats," which are located less than 2 miles from production. As a result of the very determined effort to find new oil reserves, 49 of the wildcat test wells found new oil pools in western Kansas and 7 found new oil pools in eastern Kansas. There were 289 rank wildcat tests, and among these 28 were successful ventures. They are responsible for 26 of the new oil pools recorded for the year and 2 of the new gas pools recorded. The ratio of dry holes to producing wells among such rank wildcats is thus approximately 10 to I (289 dry and 28 good). This compares with a ratio of II: I in 1942 and 6:1 in 1941; the same in 1940 and 5:Iin 1939. With nearly all wells flowing to their maximum economic capacity, the total production for Kansas during 1943 reached a new high; that is, 107,700,000 bbl., compared with 97,000,000 during the previous year. Similarly, the amount of gas sold during 1943 made a new high point on the production curve. The total amount was 122 billion cubic feet, compared with about 98 1/2 billion cubic feet for the year previous. As usual, the large Hugoton field of south- western Kansas accounted for approximately half of the total gas production. Highlights of the Year Despite the fact that 56 new pools were found in Kansas during 1943, it must be admitted that the future reserves of the state have not been increased greatly. Most of the new pools seem to be of minor value, although it is admittedly impossible to gauge the future production of any pool in Kansas with any exactitude. Judging by the later performance of some of the pools found in 1942 and in 1941, less than five of the new pools are likely to make any great contribution to the state's future oil reserves. Taking up the counties of Kansas in alphabetical order, the following statements summarize the highlights of the year. In Graham County, the Morel pool was extended to the southeast and this pool now promises to become one of the important pools of western Kansas. Several of the older wells have already contributed more than I000,000 bbl. of oil, and such a figure is considered very satisfactory in Kansas. In McPherson County, important new reserves were found by persistent drilling in township 17 S., R. I. W., the most northeastern township of the county. Many new wells in older pools and discovery wells in new pools make this region look promising. The Lindsborg pool, which had a sensational revival during 1942, was also extended in a number of directions and has now become a rather large producing area with a fairly high future potential capacity.

Jan 1, 1944

By Leo J. Vogel, E. D. Hummer, David J. Akers

INTRODUCTION An efficient refuse-disposal system is a necessary part of the modem cleaning plant. The large-scale refuse system and disposal area, engineered for the lifetime of the plant, has become more important due to the greater tonnages of refuse produced from increased quantities of mechanically mined and prepared coal. Laws and increased government regulations have affected the design and operation of disposal systems. THE EFFECT OF MINE AND PLANT OPERATION Refuse disposal starts at the mining face. The mining system, the type of roof support, the machinery used, and the degree of discipline at the face contribute to the amount and type of refuse that must be removed through the disposal system. Economies gained through modification of the mining system or mining machinery may be partially offset by increased dilution of the mined coal with impurities from associated rock formations. In some cases the change in the mining system and equipment has reduced the dilution. In all cases the ratio of impurities that must be removed from the raw-coal feed to the plant not only affects the maintenance and

Jan 1, 1979

By F. E. Lathe, L. Hodnett

This paper summarizes extensive data supplied by 40 copper converter plants in 18 countries, and includes a partial analysis and comments on the effect of converter slag composition and temperature on the fomzation and elimination of magnetite and the life of basic and neutral refractories. APRELIMINARY draft of this paper, including data from 26 companies which had submitted replies to a questionnaire, was presented at the Annual Meeting of the AIME held in New York in February, 1956. Publication was delayed in the expectation that additional replies would be received, and justification for the subsequent delay may be found in the fact that the present revised paper contains data from 40 converter plants situated in 18 different countries. The suggestion that a questionnaire be sent to the major copper and copper-nickel plants outside the U.S.S.R. and associated countries arose at the Los Angeles Annual Meeting in February, 1953, where several papers dealing with converter construction and operation were presented. In private discussions which followed, a group of metallurgists and refractories engineers raised the question why practices varied so much at different plants. Why did magnesite brick give superior service to chrome-magnesite in some plants but chrome-magnesite prove superior in others? Would metallurgical studies point the way to the development of still better refractories? Could magnetite formation be prevented in converter slags and reverber-atory furnace mattes? If this was feasible, why was a heavy circulating load of magnetite tolerated, when, in all probability, it increased copper losses in the reverberatory slags and, in some cases, made it necessary to shut down the furnaces periodically to clean out the accumulated magnetite? Was the sole purpose of coating brick with magnetite that of

Jan 1, 1959

By Frances H. Clark

IN a concern with the varied interests of the Western Union Telegraph Co., where practically all types of metals, both ferrous and nonferrous, are utilized, many types of failures of materials occur. These have to do not only with outside plant construction, such as corrosion and fatigue of line wire and cable, but also with inside plant equipment operating at such high speeds that rapid deterioration of metal. parts due to fatigue and wear results. Both corrosion and fatigue affect the life of copper wire so its normal life in any particular locality is largely dependent on the atmospheric conditions. Tensions vary widely owing to changes in temperature and ice and wind loadings and the wire is Subject to a great range of vibration caused by wind gusts aril vibration front trains or other heavy vehicles transmitted through the earth. High frequency low-amplitude vibrations are sometimes audible as singing in the wire. The other extreme is the vertical slashing or dancing of the wire observed during severe storms where amplitudes of 9, ft. or more at low frequencies have been observed.

Jan 1, 1942

By AIME AIME

THE Institute of Metals Division of this Institute held a joint meeting with the American Foundry- men's Association on Oct. 5-9, at Syracuse, N. Y. The registration at this meeting was about 150. There were four meetings in all, three of which were in con- junction with the American Foundrymen's Association. This combination works out very nicely and gives the I Division a number of practical foundry papers that it would not get otherwise. The sessions were well attended and the discussion was active. The session on Monday morning was of a general nature and consisted of the following subjects : " Refractory Problems in the Non-ferrous Electric Furnace Casting Shop, " "Temperature Control of Non-ferrous Alloys," "Atomized Coal System of Non-ferrous Melting," "Material Handling in a Brass Foundry." On Tuesday morning, the session was on "Aluminum and Its Alloys." The paper on permanent mold castings created a large amount of discussion, in fact so much that it had to be renewed after the close of the regular program. Aluminum is assuming a more important place every year and adds greatly to the program as a whole. One of the most remarkable meetings that this Division has ever had was held on Tuesday at noon in the form of a Round Table discussion, headed by G. K. Elliott, chairman of the Division, Cincinnati, Ohio. Mr. Elliott divided the members present, numbering about 80, into groups as they were seated at the tables. Each of these groups suggested a topic for discussion. They were as follows : "Fluxes on Market ;" "Simplification of Alloys;" "Pyrometric Control;" "Effect of Gas- sing Metal and Control;" "Barium Sulfate Added to Electric Furnace to Create Slight Oxidation to Remove Aluminum and Silicon;" and" Nickel in Brass."

Jan 1, 1925

By Robert W. Hunt

The memorable features of American history have been making fast during the last century, and notably so since 1860; and they are by no means confined to political or to any one branch of scientific development. Of all the industrial arts, none show a greater change or 'a mightier progress than the Bessemer manufacture. And this year, while we are celebrating the first centennial of our national life, we can also celebrate the first decennial of American Bessemer practice. While not forgetting or undervaluing what has been done in other countries, I have thought that a brief history of the introduction and development of the Pneumatic or Bessemer process in America would be of interest. In 1863 the Kelly Pneumatic Process Company was formed and an arrangement entered into with William Kelly, who had taken out letters-patent of the United States, Nos. 16,444; 17,628, reissued as 505; 18,910, dated January loth, 1857; June 23d, 1857; November 36, 1857; and December 22d, 1867, respectively. This association mas composed of the Cambria Iron Company, E. B. Ward, Park Brothers & Co., Lyon, Shorb & Co., Z. S. Durfee, and, later, Chouteau, Harrison & Valle joined the combination. Not satisfied with possessing the control of the Kelly patent, they sent Mr. 2. S. Durfee to England, to secure for this country Mushet's patent on recarburization, No. 17,389, dated May 26th, 1857, the same having been taken out in England on September 22d, 1856. In this Mr. Durfee was successful. Previous to the application of William Kelly for a patent, Henry Bessemer, of England, had taken out patents dated February 12th, 1856, and August 25th, 1856, in this country. Kelly claimed priority in the discovery of the principles of the process, and the Patent-office allowed his claim by granting him his patents. In the autumn of 1862 Mr. Alexander L. Holley, while in England, was impressed with the importance of Mr. Bessemer's invention, and so fully foresaw its future, that, upon his return to the United States, he induced Messrs. John A. Griswold and John F. Winslow, of Troy, New York, to join him in endeavoring to possess Bessemer's American patents. Mr. Holley returned to England in

By F. R. Hutto Jr., F. L. Kady Jr., L. E. Weymouth

The behavior of particulate non-metallic materials in moving contact with smooth surfaces is of interest and concern to manufacturers and users of abrasives, of fillers, and of pigments alike. The theoretical aspects of the subject have been treated to considerable extent in the literature, and correlatic,ns are available that attempt to relate various methods of hardness determination." 2 The particle size and friability are characteristics of the abrasive that are not related to the smooth surface. The hardness, on the other hand, may be visualized as relative to that of the smooth surface. In a study of abrasive action, the role that hardness, per se, plays is a complicated one. For it is necessary to compare the "hardness" of the abrasive, usually a non-metallic, with that of the smooth surface, generally a metal. Hardness of non-metallics is defined as resistance to scratch and is almost universally described with respect to the Mohs scale.3 Minerals have been rated by Mohs numerically from the softest (talc = 1) to the hardest (diamond = 10). By definition, a mineral has a designated hardness when it is scratched by the standard that is numerically just above it on the scale; and conversely, when it scratches the standard that is just below it. Hardness of metals. however.. implies resistance to indentation, a property that has been measured by a number of methods. In fact, the indentation hardnesses of the standard minerals on the hlohs scale have been determined by the Rockwell tester. Reproduced below are two versions of this correlation. 'A conversion chart, prepared by Wilson Mechanical Instruments Division of American Chain and Cable Co., merely gives the conversion from Rockwell to Knoop hardness. The relation between Knoop indentation hardness and Mohs scale has been reported by G. S. Smith — A New Scale of Hardness, The Engineer, Aug. 26. 1949. G. F. Kinney in Engineerin Properties and Aplications of Plastics reports the Rockwell hardness of the minerals directly in the Mohs scale. The question immediately arises as to whether this relation is valid when applied in reverse; namely,

Jan 1, 1961

One Hundred Sixteenth Meeting of the Institute, Monday, Feb. 18, to Thursday, Feb. 21, inclusive, 1918 A preliminary program, for the New York Meeting was printed in the January Bulletin, and a more detailed program was mailed to all members early in January. The following schedule is the outcome, of sundry committee meetings up to the middle of January. Committee on Arrangements J.` E. JOHNSON, JR., Chairman BRADLEY STOUGHTON, Vice-Chairman RALPH W. DEACON MRS. S. J. JENNINGS E. M. SHIPP J. V. N. DOER A. R. LEDOUX G. D. VAN ARSDALE L. `V. FRANCIS . . F. T. RUBIDGE ARTHUR L. WALKER Summarized Program MONDAY, FEBRUARY 18 9 a. m. to 5. p. m. Registration at Institute Headquarters. 10 a. m. Sessions on Coal and Non-Ferrous Metallurgy. 12.30 p. m. Luncheon at Engineering Societies'. Building. 2 p. m. Visit to Subway Workings.

Jan 2, 1918

By David B. Reger

Extensive drilling for gas and increased pipe-line building were the major petroleum activities in West Virginia during 1937. According to the West Virginia Department of Mines, 1034 permits to drill were issued. A running account of operations from trade journals and other reports shows that 1041 wells were drilled, resulting in 193 oil wells with 1238 bbl. of daily production; 680 gas wells with 1,048,057,000 cu. ft. of daily open flow; and 168 dry holes. The new oil-well average is 6.4 bbl. per well per day; the gas-well average is 1,541,260 cu. ft. per well per day; the ratio of dry holes to completions is 16.13 per cent. Very little attempt was made to develop new supplies of oil. Because of the continued low price, operators evidently considered it good business to leave oil in the ground rather than to produce it at a loss or on a small profit basis. The principal oil wells completed, by counties, are: Calhoun, 16; Clay, 10; Pleasants, 17; Ritchie, 42; Roane, 16; Tyler, 13; Wetzel, 11; Wirt, 14; Wood, 13. The leading counties in gas, with the number of successful wells in each, are: Boone, 54; Braxton, 31; Cabell, 48; Calhoun, 46; Gilmer, 82; Kanawha, 134; Lincoln, 44; Ritchie, 56; and Wayne, 26. General State of the Industry In Table 1 will be found an approximate summary of oil and gas territory and reserves, oil and gas production and number of oil and gas wells. The amount of land under lease is an approximation, because the exact figures are not available through any public or private agency. The proved land and reserves represent the opinion of the writer. The oil production for 1937 is subject to revision, and the gas production for the same year is only an estimate, based on demand and supply. The number of oil and gas wells now active is also an approximation, based on previous studies, and revised for completions and abandonments. Principal, Areas of Activity In Boone County, 62 wells were drilled in various localities, resulting in 4 oil wells and 54 gas wells with 18,170,000 cu. ft. of new production.

Jan 1, 1938

By R. S. French, W. R. Hibbard

FOR tensile deformation, if the stress value is defined by the ratio of the load to the actual area, and the strain value by the natural logarithm of the ratio of the immediate length to the original gauge length of the sample, the resulting data when plotted with logarithmic coordinates result in a linear relation extending from the initial plastic yielding through the maximum load and in some cases, such as for copper and brass, to fracture'.'. The normal form of the curve, therefore, is a parabola, satisfying the following equation: S = Kem [1] where S and e represent true stress and strain, K is a constant, and m is a coefficient evaluating the slope of the curve and designated therefore as the strain hardening coefficient. Hollomon² has reported that this coefficient is a function of the yield strength as effected by grain size in alpha brass, and the carbon content and heat treatment of steel. In the case of steel, the value of the proportionality constant is a function of the carbon content. It was further shown in that paper2 and also by Low and Prater -hat, if the power relation between stress and strain remains valid, the strain hardening coefficient m, is equal to the strain at the maximum or necking load. Thus, an added significant feature is that this coefficient may serve as an index of the capacity for deformation prior to localized necking and subsequent fracture, e.g. drawability. The constant K may be defined as the strength of the material at unit strain. Together the K constant and the m coefficient describe an alloy's physical properties as far as strength and ductility are concerned for a particular yield strength and, in the case of steel, a particular carbon content. The work of Lacy and Gensamer4 gives data on alloy ferrites from which very close estimates of the strength of ternary and higher iron alloys have been made. It was the purpose of this investigation to develop similar data for commercial copper base alpha solid solution alloys. Preparation of Specimens Commercial binary alloys of copper with aluminum, beryllium, cadmium, nickel, silicon, tin and zinc were investigated. In addition, laboratory castings were made of a 1 pct silicon alloy and a 2 pct aluminum alloy to complete these particular series. Two types of copper were used, oxygen free OFHC and tough pitch FC. The analyses of these alloys are shown in table I. Standard ASTM sheet tensile specimens were used to determine the usual physical properties of each alloy and to obtain stress data at strains from 0.0005 to 0.01. Small (1/4 in. x 3 in. x tk.) samples

Jan 1, 1951

By Sydney H., Ball

ONE of the important mineral discoveries of the eighteenth century was , that of the Minas Geraes, Brazil; diamond fields. The production of this and of .other diamond discoveries in neighboring states made Brazil the premier producer of diamonds, succeeding India; its 140 years of supremacy finally passed to- South Africa- 60 years ago. Three times have diamonds contributed heavily to Portugal's somewhat checkered financial history; first in the sixteenth and seventeenth- centuries when the diamond trade of India was controlled by its citizens residing in ,Goa, later in the late eighteenth and the first 75 years of the nineteenth century when the Brazilian fields were the world's source of diamonds, and now, when the Angola diamond mines are the principal source of revenue of its colony, Portuguese West Africa. Certain phases in the history of the administration of the Brazilian field are sufficiently curious to warrant description.

Jan 1, 1929

By T. A. Rickard

Freeman, the English historian, said that he had learned from Macaulay "never to be afraid of using the same word or name over and over again if by that means anything could be added to clearness or force. Macaulay never goes on, like some writers, talking about `the former' and `the latter', `he', `she', `it', and `they', through !clause after clause, while his reader has to look back to see which of several persons it is that is so darkly referred to". He might have learned also from Macaulay that a preposition makes a' feeble ending for a serious statement. How often do you hear `the former' and `the latter' in conversation? Good conversation is a guide not to be dis¬dained. When you must use `the latter', do not confuse it with `the last'. Cheap labor, cheap fuel, and cheap transport are essential, the latter [last] being particularly important in base-metal mining. The apparatus may be used to determine such gases as hydrogen sulphide, chlorine, oxides of nitrogen and some others, as well as sulphur dioxide. In the case of the latter two, etc. The two last mentioned are "sulphur dioxide" and "some others". He should have stated which two, and he should have avoided that wretched phrase "in the case of ". Pinning may be partly prevented by use of chalk, oil, or turpentine. The latter [last] is best. I "Partly prevented" is a poor phrase. `Prevented! is a word that does not lend itself readily to modification. He means `checked' or `corrected'.

Jan 1, 1931

By John Johnston

ONLY two of the Institute's 26 Local Sections were unrepresented at the delegates' three sessions, held on Monday morning and afternoon and Thursday afternoon of the annual meeting. The Philadelphia and Wyoming Sections alone sent no delegates. In all, seven hours were spent most profitably in reviewing the work done by the Institute at headquarters and in the field, comparing ideas and practices in varied activities, and in establishing personal contacts. Cordiality and the co¬operative spirit marked the meeting and apparently no one had any serious grievances to air. Four motions were introduced and unanimously passed. The first, which was introduced by B. L. Sackett, was a recommendation by the delegates that a national committee be appointed to cooperate with Local Sections in the matter of student activities, to promote Institute welfare. It was agreed that this recommendation be made simultaneously to the Board of Directors and to the Mineral Industry Education Division. A subsequent resolution by A. M. Smith was passed asking that a part of the duties of this committee be to secure the opinions of Local Sections as to the most desirable methods of interesting students in the preparation of technical papers, by giving prizes or otherwise, and to report their findings at the Section Delegates' meeting next year.

Jan 1, 1933

By L. D. Anderson

IN STUDYING Utah as a lead producing state one is immediately confronted by the fact that few, if any, of the ores of the state are valued for their lead contents alone. More correctly the ores from which this metal is recovered are characterized as silver lead. Even then the whole story is not told for many of these ores carry also gold, copper, zinc, bismuth, antimony, arsenic, tellurium, and other metals. It becomes apparent, therefore, that the production of lead i11 Utah is influenced by many factors. For example, i11 the early part of 1923 there was a marked increase in the production of the lead by reason of the efforts made by silver mines to produce as much silver as possible before the termination of purchases under the Pittinan Act in June, 1923. As nearly all silver ores carried more or less lead the production of that metal was increased with the increase in silver production. Very few, if any, ores of the State are mined for their lead contents alone. Important as Utah's contribution to the lead output of the country is nevertheless it is bound up to some extent with the production of gold, silver and copper.

Jan 1, 1925

By Edward I. Salkovitz

THE determination of the orientation of metal single crystals and the studies of plastic deformation are greatly facilitated by the use of the stereographic projection. To draw a standard projection of the crystal it is necessary to have a tabulation of the angles between the various crystal-lographic planes of the particular crystal studied. Bozorth' has published such a table for the cubic system which can be found in many reference books; such convenient tabulation for the hexagonal metals, however, does not appear to be in the literature, although scores of workers have calculated these angles. Therefore, Table I of angles for magnesium, zinc, and cadmium has been compiled. Since the c/a ratio is different for each of these metals, three separate calculations are necessary. The angles 4 between (HKIL) and (hkil) were calculated by means of the formula: Hh+Kk+½(Hk + hK)1+~3aLl cos The c/a ratios were calculated from data given in the 1948 edition of Metals Handbook. Fig. 1 is a typical (0001) standard projection of zinc. For all practical purposes, it serves for cadmium as well, as can be seen from the table. For magnesium, however, it is necessary to construct another net. R. M. Bozorth: Physical Review. (1925) 26, 390.

Jan 1, 1952

By Shiou-Chuan Sun

THE fact that coals of different ranks and even of the same rank differ greatly in their amenability to froth flotation is well known. In recognition of the need for an explanation of this phenomenon, two hypotheses have been suggested. Wilkins1 reported that the floatability of coals increased with an increase of the carbon content or rank. This postulate is handicapped by the fact that bituminous coals that possess moderate carbon contents are actually more floatable than anthracite coals that have high carbon contents, as shown in columns 6 and 9 of Table I. Taggart and his associates' implied that the difference of floatability between bituminous and anthracite coal was caused by the variation of carbon-hydrogen ratio. This is not applicable to the relative floatability of other coals and carbons. For example, column 11 of Table I shows that the carbon-hydrogen ratios of low-floating lignitic coal and non-floating animal charcoal are not only smaller than the moderate-floating anthracite coal, but are also similar to the high-floating bituminous coal. Furthermore, according to this hypothesis, high temperature coke-A (464), Ceylon graphite (1238), and lamp-black (357), all possessing extremely high carbon-hydrogen ratios, should be less floatable than other substances having much lower carbon- hydrogen ratios such as high volatile-B bituminous coal (11.9 to 22), anthracite coal (35.7 to 60.5), lignitic coal (15.6 to 33.6), and charcoal (13 to 26.2). However the former group is actually more floatable than the latter group.

Jan 1, 1954

(Under this heading will be published notes sent to the Secretary of the Institute by members or other persons introduced by members.) Mining Engineer. Graduate of Colorado School of Mines, 1912, experienced in coal, lead manganese and limestone mining, wishes execu¬tive position. A-2146. Graduate Mining Engineer.-Discharged, reserve officer, age 32, single, 7 years' experience holding responsible executive positions, in iron, copper, and talc mining. Well recommended. A-4913. Mine Manager, Superintendent or Engineer. Age 41, graduate of Michigan College of Mines; 20 years' experience in responsible positions in connection with large operations; in iron, copper, pyrites, lead and zinc mines; successful in finding and developing orebodies, increasing production, and reducing costs. Desires a position with a future. A-4081. Mining Engineer.-Graduate from Polytechnicum, Stockholm; 14 years' practical experience in Sweden, United States, Belgium, and Spain, in iron-ore development, mining, and milling; thorough knowledge of English, French and Spanish; desires position as superintendent or assistant manager. Good references; member; now in Sweden. A-4914. Research Engineer. Now in Chile on the erection of a 50-ton mill with modern machinery for the treatment of Chilean nitrate. Desires connection from the first of next year; with firm operating in South or Central America. A-4915. Metallurgical Engineer. Junior member, age 26, single, graduate Columbia School of Mines; recently discharged as lieutenant in the heavy artillery. A-4916. General Superintendent. Technical graduate, age 35, desires position over a group of four or five mines or as assistant general superintendent for a large. company. Has had experience in superintending mines, construction work, opening new and abandoned mines, safety and effi-ciency engineering and handling organized labor. At present employed by a coal company in the middle West. A-4917.

Jan 11, 1919

By William F. Boericke

THE Christy Creek clay mine of the General Refractories Co., in the Olive Hill District, ranks with the most important producers in the north-eastern Kentucky fire clay field, both from production of high-grade flint clay, as well as unusual extent and thickness of deposit. The property is but one of a number controlled by the General Refractories Co. in this district, but is given first consideration among them by the operating staff. Its total area is over 5000 acres, owned in fee or by lease of clay mining rights, and although mining operations have been in progress for over five years, scarcely one per cent of the ground has been worked as yet. The mine is near the southwestern end of the clay field, which extends in a belt 12 miles wide and 55 miles long, in a southwestern direction from Kenova, W. Va., which, as the name indicates, is at the junction of Kentucky, Ohio, and West Virginia. Olive Hill, where there is one of the l1Ulin plants of the General Refractories Co., and to which the clay from the mine is shipped, is about 26 miles distant from the mine. Connection is made with the Chesapeake & Ohio R. R. by a spur line . 8 miles in length, owned and operated by the company.

Jan 1, 1929

By H. M. Chance

Jan 1, 1887

By Morris M. Fine, Norwood B. Melcher

It is out of the question, at this time, to select any one prereduction process as superior to the others. It is apparent that several share a basic similarity and that within the groups listed in Part 1, the reduction vessel is sometimes the only significant variable. Claims as to the virtues of one machine over another are difficult to substantiate: one may be rapid, another thermally frugal. Based on published data, however, all seem to be performing adequately. It would appear that processes based on carbonized pellets are most applicable to foundry iron at low production rates. Adaptation to large scale manufacture of blast furnace hot metal or to agglomeration of fine concentrates at the mine site is much less likely.

Jan 8, 1966