Search Documents

By Gordon T. Austin

The combined value of production of natural abrasives, which include tripoli, special silica stone, garnet, staurolite, and emery, increased in 1993. The increase in the value of tripoli production was the result of an increase in total production. Special silica stone experienced an increase in unit value but decrease in the quantity produced. Garnet showed a 19 % decrease in quantity and an 8 % decrease in value. Staurolite increased about 51 % in the quantity produced and 136 % in value compared with those of 1992. Staurolite's significant increase in value of production resulted from a 56 % increase in the unit value. The fused aluminum oxide industry showed an 8 % decrease in the quantity produced and a 13 % decrease in the value of production. The silicon carbide industry saw an 11 % decrease in the quantity produced and an 8 % decrease in the value of production. Combined, the industries decreased 9 % in quantity and 11 % in value compared with those of 1992.

Jan 1, 1993

By Joel A. Hunt

The Bunker Hill Mine, located in north Idaho, consists of over 150 miles of passageways within highly fractured and faulted Precambrian metamorphosed rocks. The Bunker Hill Mine was at one time a major producer of lead and zinc; currently it is on inactive but maintained status. Ground water moving along flow paths that have been disturbed by mining reacts with pyrite and oxygen to produce acid water within the mine. Discharge of this acid water averages more than 5 cubic feet per second, with an average zinc concentration of 160 mg/L and pH of 2.8. Treatment of this acid mine drainage is required by the National Pollutant Discharge Elimination System (NPDES). Cessation of all underground activities at the Bunker Hill Mine will not terminate the production of acid mine drainage. Reclamation alternatives that could either reduce the quantity or Improve the quality of the drainage upon mine closure are highly attractive. This project is directed towards delineation of reclamation alternatives based upon an understanding of the characteristics of ground water recharge near the mine. A variety of field techniques were used to identify areas of rapid infiltration and to investigate the ground water flow system associated with the upper portion of the mine in a portion of the Milo Creek drainage. These techniques include Installation of piezometer nests, dye tracing, surface resistivity, dye dilution, spring surveys, and hydrochemical analyses. Sites of direct Infiltration into the mine have been located. These include mine workings directly below perennial streams, intersections between streams and faults, and a caved area adjacent to an ephemeral stream. Results of these investigations indicate that recharge through these sites is not as rapid as suggested by previous studies. Inflow to the underground workings from the ground water flow system around the margin of the mine may account for more mine water than sites of direct infiltration. Recharge control at areas of direct infiltration could result in a net decrease in the quantity of acid drainage from the Bunker Hill Mine. Locations suggested for recharge control are West Milo Creek above the Guy Caving Area, the intersections of the Cate Fault with South Milo and Milo Creeks, and an area of Milo Creek below the Milo Creek Dam that overlies shallow mine workings.

Jan 1, 1984

By Gordon T. Austin

The combined value of production of natural abrasives, which includes tripoli, special silica stone, garnet, staurolite, and emery, increased about 21070 in 1989. The increase in the value of staurolite and tripoli production was the result of an increase in the quantity of materials produced and an increase in the unit value. Emery decreased due to the significant decline in the volume of the material produced. Special silica stone experienced both a decrease in unit value and quantity produced. Garnet showed a small increase in quantity, but a decrease in unit value. The silicon carbide industry saw a slight decrease in the quantity produced and a 12070 increase in the value of production. The fused aluminum oxide industry showed a 5070 decline in the quantity produced, but enjoyed a 15070 increase in the value of production. Combined production for both industries decreased 4070 in quantity but increased 13070 in value compared with those of 1988.

Jan 1, 1991

By Yun-Jie Wei

Seismic areas were in the eastern margin of the Qinghai-Tibet plain, whose structures were complicated, mainly composed of Maowen fault, Yingxiu fault and Pengxian-guanxian fault. The rapid rise of the Qinghai-Tibet plain led the crustal material of the eastern edge to move to the southeast along the faults on a large scale since the late Cenozoic; Minshan block structure and Long Men Mountain tectonic zone represented the strong nappe thrust movement as the east boundary of Chuanqing slip block; the stress was accumulating when squeezed, which to a certain extent resulted in breakdown of the crust, and earthquakes. The shock speed, high-energy accumulation, and the reversed dextrorotation of the earthquake fault characteristics et al. happened, which caused the development of secondary geological disastersts. According to on-site investigation, the typical geological disasters had thrust rock collapse, the instability deposit, the revival of potential debris flow et al. whose genetic model had been analysed.

May 1, 2009

By Maurice Hunter

The paper outlines recent design developments in the computerization of surface crawler drills for the quarry industry. It references the technology firstly developed for the underground mining and construction industry, where automation and computerization has been in demand for a number of years.

Jan 1, 2003

By Joseph M. Kurtak

The Bureau of Mines (Bureau) and the U.S. Geological Survey (USGS) conducted a 4-year (1979-1982) mineral assessment study of the Chugach National Forest (CNF), Ak, as part of the Roadless Area Review and Evaluation (RARE II) Program. The USGS remapped the geology and distribution of mineral resources. The Bureau investigated mines, prospects, and mineral occurrences. This report describes the results of Bureau work in the central 790,880 acres of the Forest. Copper, with by-product zinc, silver, and gold, has been the major metal produced from the study area as well as from the entire Chugach National Forest. The majority of the copper deposits are concentrated within basaltic rocks on Knight Island but the major producers are hosted by sedimentary rocks on Latouche Island. Approximately 182.6 million lb of copper, 1.5 million oz of silver, and an unknown but substantial amount of gold were produced during a 30 year period. Currently no mines in the area are producing. Inferred, indicated and measured reserves having mineral development potential total 4.6 million tons, with weighted average grades of 1.6% copper, 0.30 oz silver/ton, and 0.04 oz gold/ton.

Jan 1, 2011

By Charles W. Merrill

The U .S. Treasury stocks of silver have been reduced at such a rapid rate to meet industrial and coinage requirements that they face exhaustion in 3 or 4 years. Alleviation of the silver problem will require increasing supply or reducing demand. This paper examines possible long-range resource development and research programs and improved secondary recovery. The possible reduction or elimination of silver in coinage and development and introduction of substitutes in the arts and industry are also discussed.

Jan 1, 1965

By Charles W. Merrill

The U.S. Treasury stocks of silver have been reduced at such a rapid rate to meet industrial and coinage requirements that they face exhaustion in 3 or 4 years. Alleviation of the silver problem will require increasing supply or reducing demand. This paper examines possible long-range resource development and research programs and improved secondary recovery. The possible reduction or elimination of silver in coinage and development and introduction of substitutes in the arts and industry are also discussed.

Jan 1, 1965

By M. Ataee-pour, S. E. Jalali

So far, a large number of algorithms have been developed for the optimization of pit limits, most of which follow deterministic rules. In this paper, a new algorithm is introduced, which follows a probabilistic logic using the Markov chain process. The algorithm is implemented on a transition matrix that corresponds to the 2D conventional economic block model of the mining area. The probability of mining a block is proportional to the desirability it may provide. Applying this algorithm, the probability of mining each block is obtained, and finally, the optimum pit limits are defined as the pit, which provides the highest probability of mining. In order to validate the proposed model, a numerical example is given and the results of the algorithm are compared to those of a dynamic programming algorithm. A 2D analysis of the problem is discussed in this paper. Although dealing with 3D problems requires larger size matrices, the optimization method is the same and the algorithm does not need any smoothing.

Jan 1, 2006

Coagulation-Neutralisation Technology to Treat Wastewater from Lead-Zinc Concentrator

Sep 13, 2010

By Bo Forsman

METAFORA is a simulation model for determination and evaluation of strategies for operating loader/truck systems in mining. A specific version of METAFORA was used to evaluate the haulage system at Solider Mineral's Aitik mine in northern Sweden, one of the largest open pit mines in Europe with a production of about 11.5 Mtpy (about 34000 tpd) of copper are. A production level of 34065 tpd was estimated by simulation runs with METAFORA. Using METAFORA's dispatch rules (Fixed Dispatch, Maximize Trucks, and Maximize Loaders), the truck/shovel system in the Aitik mine was simulated for evaluating alternative dispatch control strategies. The Maximize Trucks rule gave about the same total production (ore + waste) as the Fixed Dispatch rule but a 9% higher ore production. The Maximize Loaders rule gave the lowest production. The marginal truck capacity decreases with increasing number of trucks serving the same loader due to increasing waiting times. In Aitik mine the low crusher capacity results in long dumping times. If the dumping time at the crusher could be halved, the ore production would increase by 14%. The paper indicates that the use of software like METAFORA can result in a substantial reduction of time, effort and cost in shovel/truck system design and evaluation.

Jan 1, 1992

By George Hope, Brigitte Lacouture

"The Red Dog Mine has increased mill throughput for most years since startup. Although flotation equipment has been added over the last 10 years, the Red Dog metallurgical performance has been restricted by a lack of adequate flotation capacity. Two reduced tonnage trials conducted in 1997 as well as numerous SAG relines have consistently indicated the potential to significantly increase both zinc concentrate recovery and grade with additional flotation capacity. Late in 1999, a new circuit was designed with increased flotation capacity while simplifylng the current circuit, providing for three stages of dilution cleaning, and creating a retreat section. The purpose of the retreat section is to target the more complex particles and allow the chemical environment to be fine tuned for improved iron depression. In total, twentyone (21) Outokumpu OK50 mechanical flotation cells and four (4) 3.66m dia. column cells will be added to the current flotation circuit. The VIP (Value Improvement Program) Mill Optimization project is also addressing thickening, water treatment and power issues and has a total budget of $US105 M. Startup of equipment will be phased in to minimize the impact on current operations and is expected to be complete by the end of Q3-2001.INTRODUCTIONRed Dog Operations started production in November 1989. The mine is located above the arctic circle in northwest Alaska. It is linked by an 80 km road to a port-site facility where the concentrate is stored. Concentrate is shipped to markets throughout the world during the one hundred (100) days of open seas. Typical of sedimentary exhalative deposits, the metallurgy proved to be challenging and coupled with many mechanical shortcomings, the initial few years were very difficult. The start-up issues were slowly resolved and in 1998, a major grinding expansion, the PRI (Production Rate Increase) project, was completed. The project was designed to allow a 40% increase over the 1995 throughput. In 2000 mill throughput was 3,050,000 tonnes to produce a total of 960,000 and 140,000 dry tonnes of zinc and lead concentrates respectively, making Red Dog the largest zinc concentrate producer in the world. To address a shortage of flotation capacity remaining from the PRI grinding expansion, a project designated as the VIP (Value Improvement Program) Mill Optimization project was initiated. The mill optimization project is targeted to produce 1,100,000 tonnes of zinc concentrate at 56% zinc grade and 87% zinc recovery. The project will add twenty-one (21) Outokumpu OK50 (50m3) flotation cells, four (4) 3.66mO column cells and address water treatment, thickening and power generation capacities."

Jan 1, 2002

By Frederic P. Dewey

THE Bureau of the Mint of the United States Treasury maintains 13 offices for the purchase of gold-bullion, and this paper describes an investigation to establish the reasonable differences in the assay-results at the various institutions which may be commercially allowable in the settlements between them. Beginning with the comparative assay of proof-gold at the Philadelphia mint and the Utrecht mint, which shows 0.00002 as the closest agreement now possible, eight tables of comparative results, taken from the regular work of the service, are given. These tables begin with very fine gold, produced in an electrolytic refinery, showing close agreement. in the assay-results, and follow through decreasing gold fineness and . increasing amounts and complexity of base metals to very impure and complex bars produced at cyanide-mills, some of which give widely-varying results. Next is given a series of results on samples, prepared and sent out to various laboratories in the service, to test the influence of different metals and various combinations upon the' agreement of the assay-results; 11 samples were sent out and each one was assayed from 44 to 71 times, making a total of 623 assays. To these are added 107 assays of identical samples of coin-gold. On a previous occasion,' I have endeavored to show the degree of accuracy that may be expected in the ordinary everyday analysis of various materials, and on another occasion2 I

Aug 1, 1909

By A. Choudhury

Deep open-pit mines are becoming increasingly common in the highly mineralized arctic and sub-arctic regions. Air inversion is a frequent occurrence in these regions, and is exacerbated by the natural topography of an open-pit mine. Due to such inversions, the air quality in open-pit mines deteriorates very rapidly. Transport of gaseous pollutants under arctic air inversion is complex and involves an interaction between flow, thermal and convective transport systems. This paper discusses the construction and validation of a three-dimensional model that simulate the flow of air and the transport of gaseous contaminants in an arctic open-pit mine and the effect of low influent velocity and large gust velocities on the contaminants profiles in the mine. It was found that while higher velocities may remove contaminants from the pit bottom, they may not remove the contaminants from the pit entirely, necessitating artificial mitigation measures.

Jan 1, 2012

By H. A. Wheeler

IT may surprise some of our members to learn, among the industries based on the mineral resources of the United States that of clay now ranks third, being exceeded in value of product only by pig-iron and coal. The present annual value of clay-products exceeds the value of the outputs of gold and silver, and also exceeds the combined values of copper, lead, zinc, aluminum, mercury, antimony and nickel. These facts are shown in Table I. which gives the statistics for the year 1902

Jan 1, 1905

By C. H. Schack

Extractive metallurgy techniques currently employed to recover silver from primary ores and secondary scrap were reviewed and evaluated to identify and delineate metallurgical problems whose resolution would increase the supply of silver from domestic materials. The survey revealed that practically all primary silver is recovered by froth flotation concentration of various types of ores, followed by smelting and refining of the separate lead, copper, and zinc concentrates. Silver losses during the complex processing are, with rare exception, inconsequential. Furthermore, any silver production gain from base metal ores, which contribute about two-thirds of the total primary silver, is directly dependent no improvement in the market for the base metals. Statistical data on new and old silver scrap are wholly inadequate to make reliable conclusions about scrap processing problems and the possibility of increasing the recovery of silver from the many forms of secondary silver-bearing materials. The available information indicates (1) that efficient silver reclamation practices are employed by the larger users of silver, and (2) that recovery of additional secondary silver involves solution of problems of collection rather than of processing. Several possibilities exist for limited increases in silver production from primary ores by improvement in metallurgical practices. Specifically, research is needed to (1) solve the problem of recovering silver from the copper ores of the Copper Range district, Michigan; and (2) devise economically feasible methods for recovery of silver from presently marginal or submarginal ores char because of grade, location, and frequently complex nature cannot presently be exploited by conventional techniques.

Jan 1, 1965

By Jhon Melo

Los “softwares de aplicación” como herramientas en la exploración geológica, generan importante información geográfica sobre el área a estudiar, así como la cartografía y la toma de muestras en laboratorio. En ese sentido, el presente texto señala el manejo adecuado de dichas herramientas a través del uso de una base de datos, donde existe una estructura basada en el software (VISUAL FOXPRO, PARADOX, etc) y asi ejecutarla mediante una aplicación gráfica que permita tener una representación de lo estudiado como ocurre en un muestreo geoquímico.

May 25, 1998

By M. J. H. Ruscoe

"The circulation wear rates of pure nickel, cupronickel and nickel-plated-steel coins were measured and found to be in the ratio 1:3:1 . The relative wear rates of nickel and cupronickel coins were similar to those reported in earlier studies, and the circulation wear data for nickel were used as a reference in laboratory wear tests. A correlation between circulation wear rates and laboratory wear rates formed the basis for a prediction of service life using relief legibility as an 'end of life' criterion. This criterion was determined to be an average surface thickness loss of 12 um. The surf aces of nickel and Nickel-Banded-Steel (N-B-STM) coins were observed to harden both in circulation and in the laboratory tests at a rate of approximately I VHN/year of actual or simulated service life. It was also observed that the laboratory wear rate of N-B -S coins increased as nickel cladding thickness increased and this effect was attributed to differences in surface hardness.Wear test results are also reported for the new Canadian dollar coin material which shows a better wear resistance than pure nickel. IntroductionThe subject of coinage wear has a long history, and a number of studies have been published, concerned both with the measurement of circulation wear rates and with accelerated laboratory tests to simulate the behaviour of coinage materials in service. As early as 1803, wear tests were conducted by Hatchett on gold coinage using various types of vibratory and tumbling machines». These tests were commissioned by King George III of England who was concerned about the wear of gold coins in circulation.Early in this century, Adrian performed laboratory tests that showed that the wear rates of cupronickel 75/25 and nickel coins were in the ratio 3:1 and this ratio was later confirmed in laboratory tests reported by Daeppen and Zurrerw, The latter authors also weighed cupronickel and nickel coins that had been in circulation for various times and observed the same 3: I ratio. There was further support from Tylczak and Blickensderfer who reported significantly higher abrasive wear rates for cupronickel compared to nickel, when rubbed against sand paper."

Jan 1, 1988

By Johnny Zhang, Yang Anguo, Li Weifeng, Xueyi Guo

"SKSTM oxygen bottom blowing smelting technology was developed by SKS-ENFI at SKS Smelter, Hunan in the 1990s to replace the conventional sintering process and thus to meet the high national EHS standard for lead.Since then, two major milestones have been achieved:1. Since 2002, the SKS oxygen bottom blowing smelting-blast furnace reduction has been in operation at SKS, YGL, Chizhou smelter etc. Now in China, about 50% of the lead (4.2 millions t/year) is produced using SKS process; and2. Since 2008, the blast furnace has been replaced by direct reduction of molten rich lead slag at YGJ smelter, which is more energy-efficient since no slag cooling is required. This two stage process (SKS Oxidation- Direct Reduction) is named as the YGL process.Since 2008, numerous technological innovations have been implemented in the furnace design, process control, and maintenance at YGL. The plant has been successfully demonstrated its unique excellent performances on all aspects from processing capacity, product quality, energy reduction, cost reduction and emission reduction. The purpose of this report is to update all the improvements with proven tracks.Meanwhile, a preliminary comparison on the following aspects between the YGL process and other similar technologies has been discussed:1. Plant design and operating conditions;2. Mass and heat balances, metal (Pb, Ag) recovery;3. Consumables, oxygen gun and refractory lining life;4. Energy consumption and operating costs;5. Sulfur capture and emission reduction etc.It is concluded that the modified SKSTM process is a clean SO2-free emission process. The process is characteristic of other features such as no extra fuel addition, low capital with a small foot-print design, low OPEX, high throughput, easy operation, long refractory lining life and high productivity (95%+ on line time annually). It offers an alternative cost-effective technology for lead smelting industry."

Jan 1, 2014

By Gordon T. Austin

The combined value of production of natural abrasives, which include tripoli, special silica stone, garnet, staurolite, and emery, increased about 4% in 1990. The increase in the value of tripoli production was the result of an increase in the unit value. Emery increased owing to an in? crease in the volume of the material produced and an increase in the unit value. Special silica stone experienced a decrease in unit value and an increase in the quantity produced. Garnet showed a 10% in? crease in quantity and a 73% increase in unit value. Staurolite decreased about 8% in the quantity produced, and the value of production decreased about 10%. The fused aluminum oxide industry showed a 5% decline in the quantity produced and in the value of production. The silicon carbide industry saw a 10% decrease in the quantity produced and a 9% decrease in the value of production. Production for both industries decreased 7% in quantity and value compared with those of 1989.

Jan 1, 1993