Search Documents

By M. Kanefsky, A. Q. K. Rajput

Two channel polarity coincidence and polarity difference statistics are analyzed. The signal, common to both channels, consists of sinusoidal bursts where the exact frequency of the signal is nearly known, but other parameters such as amplitude, phase, and pulse starting time are unknown. The noise inputs are dependent, narrow band, Markov processes. It is shown that the performance depends not only on the signal uncertainties but on the precise shape of the cross-correlation functions between the noise inputs. By using two polarity difference statistics in addition to the polarity coincidence statistic, it is shown that the decrease in performance, as well as the cost of hard limiting due to correlated inputs, can be made small.

Jan 11, 1981

By William R. Hess

Volcanic ash, although a little-used Kansas resource, is available in forty counties with estimated, reserves of more than 20 million tons. It was first produced in Kansas in the early 1900?s but not until the early 1920 is did it become an important abrasive material. Total production to date is estimated at 2 million tons, the major use being as an abrasive in scouring compounds and soaps, additional uses include ceramic glazes, an additive in cement, and a filler and stabilizer in hot mix asphalt for paving. Unrecorded tonnages have also been used in construction of black-top (macadam) roads. From 1916 through 1944, Kansas ranked first among the states in volcanic ash production; peak production was about 52, 000 tons in 1923. Since 1945, production has steadily declined, primarily because materials other than volcanic ash are now being used for abrasives; only two producers operated in 1964.

Jan 1, 1965

By Kerstin Malmqvist

Simulation technique has been used for a feasibility study of a deep exploration project for massive, sulphides in an old mining district, the Skellefte field. An interactive computerized mathematical model of an ore field and a drilling procedure has been constructed. It is possible to represent varying geological structures. The model also takes in consideration economical factors such as drilling costs and ore values. On this model Monte Carlo simulations and probability calculations are done in order to estimate the outcome of different drilling strategies under varying geological assumptions. Under the specific conditions of the well known Skellefte field, it is found to be possible to even calibrate the mathematical model.

Jan 1, 1979

By W. Dresler

"A major Canadian chromite deposit at Bird River, Manitoba is one of the largest known chromite reserves in North America but it exhibits low chromium contents and low chromium to iron ratios. Commercial beneficiation techniques permit these ores to be upgraded to concentrations which, however, remain inferior to most other ores and concentrates used worldwide f or production of high-carbon ferrochromium. Analyses for reduction of low-grade concentrates by submerged-arc electrofurnace techniques predict chromium contents between 45.9% and 51% for a high-carbon ferrochromium alloy. Relatively high over-all chromium recoveries between 79.5% and 91. 1% can be achieved. Alloy compositions for Cr, Fe, C and Si are determined for various burdens with low-grade concentrates. Consumption data per ton contained chromium are obtained for electric power, coke, concentrate, quartzite and limestone. The data are compared with those of high-carbon ferrochromium producers in South Africa. Economic aspects are discussed and compared with a South African reference study.IntroductionThe present ferrochromium demand in the western world is estimated at approximately 1.7 Mt with a consumption of approximately 0.36 Mt in the U.S.III and 0.03 Mt in Canada'-', A low estimate of the installed production capacity for ferrochromium in the non -communist world is 2.4 Mt. This production capacity of ferrochromium by far exceeds the demand, which is also evident from the fact that no shortage in supply of ferrochromium to the world markets was encountered in the past. Supply-demand comparisons therefore suggest that in the foreseeable future no new chromite or chromium producers should enter the world markets unless superior chromites or superior technologies are successful in competing with existing producers. Neither one of these conditions exist presently in Ca nada or the U.S., although essentially no ferrochromium is produced and no chromite is mined in these countries at the present time."

Jan 1, 1986

By R. Shen

This paper presents results of a feasibility study of recycling manganese furnace dust generated in production of ferromanganese and silicomanganese at Tasmanian Electrometallurgical Company, Australia. Dried manganese furnace dust contains about 20 wt% of carbon, in average 33.4 wt% of manganese and 1.3 wt% of zinc. Manganese in the dust is in the form of MnO, Mn3O4 and MnCO3; zinc is mainly in the form of ZnO andZnSO4. Analysis of the zinc balance with dust recycling showed that to keep zinc intake at the acceptable level, it should be partly removed from the dust. In the reduction laboratory experiments, zinc oxide was reduced to zinc vapour by tar of the dust. Reduction of zinc oxide started at 800°C and zinc removal rate increased with increasing temperature; removal of zinc was close to completion at 1100oC. Optimal conditions for removing zinc from the dust include temperature in the range 1000-1150°C, inert gas atmosphere and furnace dust fraction in the furnace dust-manganese ore mixture above 60%. In the sintering of manganese ore with addition of manganese dust in the sintering pot, zinc was reoxidised and deposited in the sinter bed. Removal of zinc in the sintering pot tests was in the range 4-17%. Up to 30% zinc removal was achieved from the bottom layer of the sinter bed. It can be concluded that zinc removal will be low during the processing of manganese furnace dust in the sinter plant. The zinc removal rate will be the highest when pelletised manganese furnace dust is added to the bottom layer of the sintering bed.

Jan 1, 2007

By R. G. L. McCready, Marco Zentilli

"Brogan coal containing mean averages of 6,93% w/w total sulphur (1.1% sulphate sulphur, 1.6% organic sulphur and 4.24% pyritic sulphur) and 16.34% mineral ash was used as the test coal in these studies.Shake-culture leaching studies on seven size fractions of the coal, ranging in size from 0.045 mm to 1.7 mm, showed that the rate of pyrite leaching was inversely proportional to the particle size. As the use of continuous stirred tank reactors would be uneconomical for the reclamation of waste coal, column leaching studies were initiated on coal sieved to >6.35 mm to < 12.7 mm, The leachate was monitored for all metal ions and the release of iron was used to monitor the rate of pyrite oxidation . Measurable amounts of Zn, Co, Ni, Mn, and V, all of which can replace iron in the pyrite crystal structure, were released during the initial stages of leaching. Further, high concentrations of AI, Ca and Sr and trace amounts of Sn, As. Se, B, Ca, Cr, Si, and Ti were detected in the column effluents.These studies suggest that bacterial leaching will remove the pyrite and qualitative amounts of environmentally undesirable trace metals from the coal if such a process is developed for waste coal reclamation.IntroductionIn 1947, Colmer and Hinkle showed that acid mine drainage was the result of an oxidative attack of the iron-mineral sulphides by Thiobacillus ferrooxidans to produce sulphuric acid . Ashmead (1955) proposed the use of these organisms to desulphurize coal , but the subsequent research effort was concentrated on the metabolism and physiology of these extreme acidophiles.A limited number of studies have been reported on the bacterial leaching of pyrite from coal (Silverman et al., 1963; Dugan, 1977). However, the bacterial oxidation of pyrite is a self-limiting first-order reaction, probably due to the precipitation of Fe(OH)J and elemental sulphur , which progressively inhibits intimate contact between the bacterial cells and the sulphide-mineral surface. Consequently, the best pyrite oxidation experiments with coal reported to date required five days to remove 97070 of the pyrite (Dugan &Apel , 1978) using mixed cultures of T. ferrooxidans and T. thiooxidans."

Jan 1, 1985

By D. Bois, P. Poirier, B. Bussière

Environmental desulphurization is an attractive alternative for the management of acid generating tailings. Bulk sulphide flotation is the most commonly used method to produce desulphurized tailings, as shown from many previous works. This process can reduce the volume of problematic tailings to manage by making a sulphide fraction concentrate. The desulphurized tailings can then be used as construction material for an engineered cover to prevent acid mine drainage. In this paper, the results from different laboratory and pilot scale flotation tests are presented. These results confirm that low sulphide non-acid generating tailings can be produced by froth flotation. It is also demonstrated that sulphide concentrates obtained from desulphurization mixed with the appropriate binders can be used as feed material for paste backfill. From previous work on the evaluation of operating and capital costs of the desulphurization process for different ore types, the use of desulphurization as a tailings management approach was studied for several scenarios. The desulphurization process was then compared with other technologies (underwater disposal, engineered soil cover) currently used to prevent acidic drainage (AD) for a new mining operation. Results show that partial or total desulphurization are technically and economically viable options to manage tailings during mine operation. Mine waste managers should consider desulphurization as an efficient technology.

Jan 1, 2005

By Mostafa Benzaazoua, Bruno Bussière, Philippe Poirier, Denis Bois

"Environmental desulphurisation is an attractive alternative for the management of acid generating tailings. Non selective froth flotation is the most commonly used method to produce desulphurized tailings, as shown from many previous works (McLaughlin and Stuparyk, 1994; Bussière et al., 1995; 1998; Benzaazoua et al., 2000a,b; 2002). This process can reduce the volume of problematic tailings to manage, by making a sulphide fraction concentrate. The desulphurized tailings can then be used as a moisture retention layer in a cover with capillary barrier effects to prevent acid mine drainage.In this paper, the authors present the results from different laboratory and pilot scale flotation tests which confirm that low sulphide, non-acid generating tailings can be produced by froth flotation. It is also demonstrated that the sulphide concentrates obtained from desulphurisation, when mixed with binders gave good long term results in terms of mechanical behaviour, thus demonstrating that the sulphide fraction can be used for paste backfill material. From previous work (Bussière et al. 1998, 1999) on the evaluation of the operating and capital costs of the desulphurisation process for different ore types, the use of desulphurized tailings to create a dry cover was then studied for several scenarios. The desulphurisation process was compared with other technologies (underwater disposal, engineered soil cover) currently used to prevent acidic drainage (AD) for a new mining operation and the advantages and disadvantages of desulphurisation are presented as well as the costs of this method of AD prevention.INTRODUCTIONThe principal environmental problem of the mining industry today is the generation of acidic drainage (AD) resulting from the natural oxidation of the sulphides in mine tailings. This phenomenon involves the generation of acidity which increase the amounts of toxic metals in the waste water released into the environment by a mine. The environmental impact of the AD has been described in detail in previous work (e.g. Down et Stocks, 1977; Ritcey, 1989; Gray, 1997; Ripley et al., 1996; Aubertin et al., 2002)."

Jan 1, 2004

By S. K. Chaurasiya

o meet the ever increasing demand of iron oxide feed stock for rapidly growing domestic steel industries and to effectively manage the depleting reserve of high grade lumpy iron ore, Pelletization of iron ore fines/slimes are expected to play a dominant role in the near future. Use of pellets will also enable the blast furnace operator to achieve higher levels of productivity with lowering of operating cost. The effective utilization of Iron Ore Slimes is important not only from the point of view of optimum utilization of Iron values in the mined ore but also for preventing environmental pollution. A significant amount of slime is being accumulated at the tailing dam of one of the iron ore mines and with the present scale of operation the tailing dam will be filled in another 10 years. Hence to increase the life of tailing dam and for better utilization of the iron values a study has been carried out for the suitability of pellet manufacturing with slimes and fines at our laboratory. The pelletization studies are aimed for optimization of various parameters for production of Blast furnace/ DR grade pellets from beneficiated slimes and Fines. This paper attempts to describe the production of blast furnace grade pellets from beneficiated slime and fines and its characterizations.

Sep 1, 2012

By Yehia M. Eyssa

A "straight wire" flow through magnetic ore separator has been designed, built and successfully used to separate magnetite from typical slurries. The purpose of these experiments was to simulate the high field profile of a "straight wire" superconducting magnetic separator which would be capable of separating weakly magnetic hematite ore from typical slurries. Magnetite was used as the test mineral because it experinces the same magnetic forces at low field as does hematite at high field. The present separator concept is based on the fact that there is a particle concentration profile due to the gravity field for low velocity turbulent flow. When a magnetic field force of -g is applied the concentration profile of the magnetic particles will be reversed leaving the nonmagnetic particles flowing alone at the bottom of the channel. By means of a divider at the end of the channel the concentrate is separated from the tailings. It is shown that the time needed to deflect hematite particles in a narrow cylindrical channel concentric with the superconducting wire is small enough so that high throughputs in the turbulent flow region are possible. In the case of a high field superconducting separator the centrifugal force could replace gravity by rotating the flow around the straight wire conductor.

Jan 1, 1974

By Roswell Johnson

To know the rate of decline of oil wells is very important, yet ordinarily we are prevented from getting this rate because the oil from several wells is put into one or a few tanks as soon as the wells have been connected to the power. The object of doing this is economy of tanks, pipes, labor and accounting. FIG. 1. But we are making a great sacrifice for this small economy. The advantages of the individual records are that we would know better: 1. When the well has ceased to be profitable. 2. When a well has gotten into bad condition. 3. The real record of the yield per acre and the rate of decline of the wells. The lease total is too mixed as to age of the wells for existing records to have much significance. To obtain such individual well records and more accurate logs are the great desiderata of satisfactory management of oil properties. 4. Which wells show the slowest decline-information which is valuable in locating new wells or purchasing adjoining leases.

Jan 6, 1917

C. P. BOWIE, San Francisco, Cal.-In my work with the U.S. Bureau of Mines, I have been detailed to report on oil storage containers, and in going around the country I have, been much interested in, the possibilities in the use of concrete for such containers. In talking with a good many people, I have discovered that concrete is being used A good deal for a wide variety of oils ranging from 14° to as high as 40° Bé., especially, by some of the western railroads:, If any member has had experience, in storing gasoline in concrete, I should like to learn of it. DORSEY HAGER, Tulsa, Okla.-Mr. M J. Munn, formerly .with the U. S. Geological Survey, acid connected with the Gypsy Oil Co., until a short time ago, has invented a invented a method for the application of concrete to the storage not only of crude oil but of refined products:. The Cosden Oil Co., of Tulsa, is now working on that plan, and, expects to store refined products in concrete tanks. THE CHAIRMAN (I.N. KNAPP, Ardmore Pa.).-I have had considerable experience in building masonry tanks for gas Holders. I do not believe it is possible to build a concrete or masonry tank of any kind. With hydraulic cement, mortar, which will be absolutely water-tight, unless the bottom and inner wall, after completion are waterproofed with some impervious material. The same will be true of oil tanks, the bottom and inner face of which must be made impervious to oil. Masonry tanks are intended to be sunk in the ground. All that the wall of the tank then amounts to is a retaining wall to keep the excavation in shape and to receive an impervious coating. The bottom of, a; tank, when empty, must be protected by a relief valve from any hydraulic: pressure acting from below. At ordinary prices, for sheets, a tank 100 ft. diam by 20 ft. deep can be built of steel much quicker and cheaper than of masonry. Several years, ago I saw very large oil storage tank under construction in California the bottom and sides being concrete. The sides were, sloped at about the single of repose for the material excavated: If you build a steel oil tank, you can get. .men for the work who do nothing else, and you, are likely to get a satisfactory job; but if you wish to build a concrete or masonry tank it is almost: impossible to find men skilled in building absolutely water-tight masonry Work. The general idea is that any laborer can mix up concrete in any old way and make a,

Jan 1, 1918

By R. L. Keiski, H. Miettunen

"The serpentinite massifs of Hitura are located in the municipality of Nivala in Central Finland. The most important sulfide minerals in the ore are pentlandite, pyrrhotite and chalcopyrite. The ore body consists of amphibolite rocks in contact with serpentinite against mica gneiss. The mean Ni grade of the ore is about 0.7%, and the highest Ni grades have been encountered in close contact. In general, the inner parts of the ore are strongly serpentinized ultramafite and some sulfides have been converted to mackinawite and valleriite. The degree of alteration varies considerably within the ore body and, correspondingly, the grain size of the sulfides varies as well. In this study, flotation tests were done with samples from different zones of the ore body. The flotation test results on the bench scale and plant scale are discussed in terms of the mineralogical features of the ore. Ores in the North Hitura zone differ from those in the South Hitura zone.IntroductionThe Hitura nickel mine, like the entire Nivala area, is part of the Bothnian Svecokarelian schist zone, where numerous Ni-Cu boulders have been discovered since the early 1930s. The Nivala area has therefore been the subject of exploration activities by the Geological Survey of Finland (GSF) and mining companies. The first period of exploration started in 1936, and the Makola nickel deposit, located 3 km south of the Hitura mine, was discovered by GSF in 1937. About 415,000 tonnes of ore were mined at Makola between 1941 and 1954. In 1937, during the exploration and development stage of the Makola mine, boulder tracing and a geophysical survey revealed a significant ultramafic body with some lowgrade Ni-Cu occurrences in the South Hitura zone.In 1961, GSF continued the exploration program in the area and discovered the North Hitura ultramafic complex and its allied Ni-Cu occurrences. In 1964, Outokumpu Oy bought the property and, after underground exploration, comprehensive mineralogical studies, process research and a feasibility study, production started in 1970 (Isohanni et al., 1985)."

Jan 1, 2015

A BRIEF account of the water-power potentialities of Tasmania is given, together with possible applications of the power commercially. A short history of the Waddamana development is then given, and the main works are described.WATER POWER POTENTIALITIESTasmania is an island of approximately 24,500 sq. miles area (exclusive of small islands). An area of 12,000 sq. miles is at an elevation of over 1000 ft. above sea-level, and of 2300 sq. miles at over 3000 ft. above sea-level. Average annual rainfall varies from&apos; over 140 in. on West Coast to 20 in. on East Coast, and for the whole island averages 48.5 in. The total water-power available, based on conservative figures for run off and efficiency, is 6,000,000 b.h.p. Only a small percentage of this total will, under present conditions, and under likely conditions in the immediate future, be capable of being developed commercially.An extensive hydro-metric and water-power survey is at present being carried out in order to collect information concerning the most promising water-power schemes. Already 400,000 b.h.p. has been located in different proposals, and there is still a large area of very likely country along the West Coast which has not been investigated yet. Tasmania thus has very vast power potentialities, which, combined with good ports and communications and wonderful mineral and timber resources, should augur well for the establishment of the great key industries, particularly chemical and metallurgical.

Jan 1, 1923

The principles of geometry and trigonometry are so continuously used by mining engineers for the purpose of accurately and intelligibly recording their measurements, that the writer is prompted to lay the following cursory remarks upon mine surveying before the members of this Institution in the hope of eliciting a free interchange of opinion upon details of this interesting branch of the profession. He proposes to deal with surveying only so far as it concerns the mining engineer, not to intrude upon the domain of the professional surveyor, and, in this instance, to discuss more especially that which may be termed the mechanical, rather than the mathematical side of surveying.In the latter part of the eighteenth century and the beginning of the present one, the usual underground surveying equipment in the English metalliferous mines, consisted of a magnetic needle in a fiat square wooden box of about 9-inch sides, a two-foot rule, a long cord, aud a stool, upon which to place the needle and box. The operator took his bearing by sending his assistant with the end of the cord as far in a straight line as the length of the cord would admit.On its being drawn that he held its end in one hand and placed the side of the compass-box against it with the other, and noted the bearing thus found either by a book entry, or by ticking it off with a piece of chalk on the board the compass lay in. He then measured the cord with a two-foot rule. It is needles to say that with these appliances the accuracy of the results were open to question, and mining surveying was not unduly popular.In the present day, engineers have the advantage of using instruments brought to such a state of perfection, and of employing such an exact system of underground surveying, that inaccurate work must usually be attributed either to lack of care, or lack of ability in the operator.

By J. B. Forrester

In the operation of the coal mines in Utah few adverse conditions confront us. Physical conditions for the economical extraction of the coal are as near perfect as it is possible for them to be. Still several obstacles are encountered to keep up our interest and prevent us from getting in a rut. Of these I shall speak only of Burning, Wants, and Sluffing of Ribs. Should one travel the outcrop from Ivy Creek in Emery county to the Utah-Colorado line, there would be one outstanding feature indelible impressed upon one&apos;s mind. That feature is the omnipresent indications of burning in place. Viewing the eastern escarpment of the Wasatch Plateau from a distance, many splotches of dark red are plainly seen always lying above the coal floor. This stratum is a felspathic sandstone, appearing as a white line running the full length of the above escarpment and about midway between the floor of the valley and the top of the plateau. The coal bearing complex consists of shales, sandstones and coal. This complex varies from two hundred to eleven hundred feet in thickness. The number of coal seams are exceedingly variable. As a rule the argilutites form the bulk of this complex. This material is baked by the burning of the coal and the iron present is oxidized to the ferric state, coloring the shale to a dark red. This baked material forms a shingle tales that in places cover the entire complex. It is natural to expect that the most extensive burning is in the canyons facing to the south and east and on the south slopes of the ridges running to the east or west. Such, indeed, is the case. Still in this arid region many crop fires have existed upon the north slopes, especially in those canyons that face to the east. In fact today, instances are not rare where grassy north slopes, heavily timbered with balsam and fir that have attained a diameter of 14 to 24 inches, are found growing upon the disintegrated baked shingle and later development proves that the coal has been burned at least 500 feet back from the outcrop. Still these conditions are not normal. In this arid climate the south and east exposures are steep and barren, except for the scrub pine, cedar, mahogany and kindred semixerophytes. Bunch grass is also a lover of such exposures. There is very little soil found in such places; it is either blown away as fast as formed or washed away by the rare torrential rains, or the rapidly melting snow. Thus we see that the physical conditions are favorable for the starting and maintainence of outcrop fires. This brings us to the probable origin of this phenomenon. There are four probable ways&apos; that such fires, could be started, namely:

Jan 1, 1921

By N. Kinoshita, Y. Inada

The authors have proposed and discussed storage of low temperature materials such as LNG, LPG and frozen food in rock caverns. In this case, as the rock mass around the caverns will receive effects of low temperature, it is necessary to consider the thermal behavior and the stability of caverns. In this study, strength and deformation characteristics obtained by the uniaxial tension test and the compression test at low temperatures were discussed. Using the results, temperature and stress distribution around caverns when LNG was stored, were analyzed. Then thermal behavior of the rock mass around caverns was discussed. Die Autoren haben Lagerung von Niedertemperatur-Materialien wie LNG, LPG und tiefgefrorenen Nahrungsmitteln in Felskavernen vorgeschlagen und diskutiert. Da in diesem Fall die Felsmasse um die Kavernen den Effekten der niedrigen Temperatur ausgesetzt ist, ist es erforderlich, das Thermalverhalten und die Stabilität der Kavernen zu berücksichtigen. In dieser Untersuchung wurden Stärke-und Deformationseigenschaften, die durch ein-axialen Spannungstest und Kompressionstest bei niedrigen Temperaturen erhalten wurden, diskutiert. Mit diesen Ergebnissen wurden Temperatur- und Stressverteilung um die Kavernen bei Lagerung von LNG analysiert. Dann wurde das Thermalverhalten der Felsmasse in der Umgebung der Kavernen diskutiert. Les auteurs proposent et discutent l&apos;entreposage de matériaux à basse température, tels que le GNL, le GPL et des aliments congelés, dans des cavités rocheuses. Comme, dans ce cas, la masse rocheuse entourant la cavité subit les effets des basses températures, il est nécesaire d&apos;étudier le comportement thermique et la stabilité des cavités. Dans cette étude, les auteurs discutent des caractéristiques de résistance et de déformation, obtenues par essai de tension uniaxial et essai de compression à basse température. En se servant des résultats, ils analysent la répartition de la température et des pressions autour des cavités, lors du stockage de GNL. Ils discutent ensuite le comportement thermique de la masse rocheuse autour des cavités.

Jan 1, 2003

By Y. P. Chugh

During late 2010, a scientifically founded water spray system was developed for continuous miners (CM) (Patent Pending) that reduces respirable dust exposure for miner operator by about 30%. It includes engineered sprays around the cutting drum, outer bit-ring sprays, chassis sprays and side cutter boom sprays. About 3.6 ? 4.5m (12-15 ft) behind these sprays is additional sprays that spatially cover the area between the CM chassis and the mine roof and ribs. The spray system uses approximately the same volume of water as currently used on CMs with similar operating pressures. An Illinois mine decided to implement these concepts on a CM during rebuild stage. Dust control performance of the rebuilt CM was evaluated using gravimetric sampling and real-time monitoring using multiple personal dust monitors (PDMs). The average results based on about 105 cuts show about 30% and 20% reduction in dust exposure for the miner operator, and the haulage unit operator. Visibility in the mining areas was also significantly improved. The coal company has already decided to implement the system on all their CMs.

Jan 1, 2012

By Yoginder P. Chugh

Beginning in 2010, a scientifically-founded water spray system for continuous miners (CMs) has been in development at Southern Illinois University that significantly reduces respirable dust exposure for workers in the face area (patent pending). It includes engineered sprays around the cutting drum, outer bitring sprays, chassis sprays and side cutter boom sprays. About 3.6?4.5 m behind these sprays are additional sprays that cover the area between the CM chassis and the mine roof and ribs. The innovative spray system uses approximately the same volume of water as spray systems currently used on CMs and with similar operating pressures. The innovative spray system design also takes into consideration coal dust wettability. An Illinois mine decided to implement these concepts on a CM during the rebuild stage. Dust control performance of the rebuilt CM was evaluated using gravimetric dust sampling and real-time monitoring with multiple personal dust monitors. The average results based on gravimetric sampling of about 105 cuts show about 30 and 20% reduction in dust exposure for the miner operator and the haulage unit operator, respectively. Visibility in the mining areas was also significantly improved. Since the initial demonstration, the coal company has implemented the system on all of their operating CMs.

Aug 1, 2013

By A Patwardhan, M M. Alam, K K. Thatavar

A commercial wet scrubber was used in the SIU-Joy dust control laboratory to test several concepts for improving the dust control efficiency of a wet scrubber. The concepts tested included two filter-two-spray systems, hollow and full-cone sprays, horizontal and vertical sprays, different layer filters and addition of surfactant. The optimised scrubber configuration had water-only vertical sprays for pre-wetting coarse dust, and vertical surfactant-laden water sprays for wetting ultrafine particles. This scrubber configuration reduced dust concentrations from 250 mg/m3 to 1.8 mg/m3. In comparison, the conventional scrubber configuration in the feed provides an outlet dust concentration of 3 - 4 mg/m3 in field operation. Upon successful testing and optimisation of parameters in the laboratory, field demonstration of the concepts was conducted at an Illinois coal mine. The optimised scrubber configuration was tested in the field with good results in terms of improved visibility in the face area and reduced respirable and quartz dust concentrations. Additional modifications in the field involved relocation of the scrubber suction inlets from the bottom to the side and changing the water spray configuration on the miner head. These additional changes were based on a conceptualised spatial dust distribution profile in the face area. The results of these laboratory development and field demonstration studies are presented in this paper.

Jan 1, 2005