Search Documents

By J. Shibata

The recovery process of valuable metals, such as Ll, Mn, Ni and Cr from a waste lithium battery was developed n this study. Lithium and Mn are selectively leached from the battery by using dilute mineral acid. Main part of the battery comprises stainless steel, and Fe, Ni and Cr are easily leached by the mixture of dilute HCl and HNO3 Lithium and Mn are precipitated as metal carbonates from the? individual leached solution with sodium carbonate solution. The solution containing Fe,Ni and Cr Is treated by solvent extraction to separate NI and Cr from the leached solution. The experiments are carried out for leaching and separation steps. According to the experimental results, the flow. sheet for a recovery process of valuable metals from a waste lithium battery has been established.

Jan 1, 1995

By Dale A. Zuck

Recovery of aluminum metal from drosses? is a major factor in the recyclability success story enjoyed by the United States aluminum industry. Today's modern dross processor uses the latest technology to maximize metal recovery at the lowest cost while complying with all environmental laws and regulations. Most dross processors, however, pay little attention to the resulting saltcake, the end residual of dross recyCling, and rely on landfills for .disposition of this material.. The alternative is to recycle the saltcake, but the success of this technology is dependent on the development of reliable outlets for each of the saltcake constituents. This paper discusses the evolution of an aluminum dross oxide processing technology that ,produces an economically attractive source of alumina for the production of portland cement.

Jan 1, 1995

By Maneesh Singh

During the various stages of iron & steel production a number of iron-rich by-products are generated. The traditional way to recycle them back to the blast furnace has been the balling - sintering process. These by-products can also be made into cement-bonded agglomerates for use as burden material for blast furnaces. In order to improve the quality of agglomerates the effects of various processing parameters on the properties of cement-bonded briquettes have to be controlled. This paper looks into the various aspects of producing cement-bonded agglomerates and using them as burden material for blast furnaces.

Jan 1, 2003

By Norbert L. Piret

During smelting of copper, arsenic in the feed reports to a large extent to the gas phase and some enters the anode copper. From the gas phase it is transferred during wet gas cleaning directly, or indirectly after dust processing, to aqueous solution. During the electrorefining and anode slimes processing, the anode arsenic content is also transferred to aqueous solution. Technology for the efficient removal of arsenic from process streams and cleaning of aqueous effluents is well established. However, the arsenic-bearing products, which thereby are generated, can vary widely in consistency, quality and quantity, from large amounts of gypsum contaminated with water-soluble arsenic compounds to residues with high arsenic content ' or arsenic products. Arsenic management in a copper smelter not only is involved with the duty of compliance to the gaseous and aqueous emissions standards but also should have as objective the minimization of the generation of arsenic-bearing and, in general, heavy metal-bearing solid waste. The present paper outlines options and the associated economic aspects for minimization of arsenic-bearing solid waste generation, for improvement of the environmental compatibility of the residues to be deposited and for the .production of commerciable arsenic compounds under appropriate market conditions.

Jan 1, 1999

By Sung-Joo Lee, Gi-Chon Han, Nam-Il Um, Hee-Chan Cho

"In Korea, almost all of bottom ash produced by coal power plants is disposed of in ash ponds. Ash storage areas comprise more than 80% of most coal power plant sites. This disposal method is causing environmental problems and a managerial burden for plant operators. In this study, investigations to develop a beneficiation process for separating coal pond ash into various products were undertaken. To improve efficiency of the separation, coal ash was separated by sizes and each size fraction was subject to various beneficiation processes. The separation process used were flotation (-200 mesh size), hindered settling (16x200) and tabling (16x200 and 8x16 mesh). The results showed that various marketable products, such as lightweight aggregate, sand, high-carbon fuel, could be recovered from coal pond ash using simple physical separation techniques.IntroductionDue to the increased use of coals every year, about fifty million ton of coals were used in 2007 alone. As a result, about 6 million tons of coal ash were generated. In Korea, the coal bottom ash is classified as a general industrial waste and is usually disposed of in ash ponds. The costs for this disposal method continue to increase due to rising costs of site management and development and more strict environmental regulation. Therefore, utilities are constantly looking for ways to increase utilization of coal ash. In this study, various beneficiation processes were evaluated to examine the possibility of separating coal pond ash into various products which can be used as aggregates and high-carbon fuel."

Jan 1, 2008

By Ozgul Dere Ozdemir, Muge Sari Yilmaz, Sabriye Piskin, Deren Sibel Kasap

"Galvanic sludge is generated at the end of the waste water treatment process of metal plating system. The waste sludge is one of the main hazardous solid wastes produced by metallurgical industries. It is caused the harm of human health and damage of the environment due to containing reasonable amounts of toxic metals (e.g., nickel, zinc, copper, chromium, iron, lead, cadmium, etc). The concentration of those toxic metals in the wastewater might reach 30% (w/w, dry weight) making their removal and recovery an interesting issue.In this study, synthesized titanium dioxide is used as adsorbent to remove nickel in leachate of galvanic sludge. The adsorption experiments were carried out isothermally at four different temperatures. The effects of pH, temperature, and contact time on nickel adsorption efficiency were investigated, and the optimum parameters were determined from the experimental studies. The experimental results indicated that pH, temperature, and contact time played a significant role on the adsorption capacity of nickel.IntroductionRapid industrialization has caused increasing the heavy metal concentration in biosphere with the industrial wastes. These wastes are generated in various industrial processes such as electroplating. Galvanic sludge is a hazardous waste that generates from metal plating industry by chemical precipitation of heavy metals from acidic or alkaline solutions during the waste water treatment process. Heavy metals are tend to bioaccumulate thus they are treated the living organism [1-2].Galvanic sludge is mainly disposed on landfills for these reason it is a big problem for environment. Galvanic sludge containing nickel (II) is common because nickel (II) is used in electroplating process [3]. In drinking water, nickel may cause health problems if found in amounts greater than the health standard set (MCLG: 0.1 mg/L) by the United States Environmental Protection Agency (EPA). The higher concentration of nickel (II) in ingested water may cause severe damage to lungs, kidneys, gastrointestinal distress, e.g., nausea, vomiting, diarrhea, pulmonary fibrosis, renal edema, and skin dermatitis [ 4]. For these reasons, it must be treated before disposed to landfill."

Jan 1, 2011

By Hideki Yamamoto

A new technology to convert fluoride gas (C2H2F4 : R-134a) contained in the exhaust gases from semiconductor manufacturing plants and refrigerators directly into a harmless substance have been established, thus, presenting a new concept for the disposal of fluoride gases such as CFCs that are associated with the global warming. Experimental results verify that chemical reactions with metal compounds can take place at substantially lower temperatures of 700- 800K as compared with combustion treatment temperatures of 1200-1500K. The reaction product is mainly metal fluoride, which chemically is a harmless material. Furthermore, this process is compact, easily controlled, safe and has low running costs. This paper deals with a new chemical reaction method for the harmless disposal of gases effecting the global warming.

Jan 1, 2003

By Ashish D. Patel, Ramesh S. Minisandram

"Vacuum Arc Remelting (VAR) is the final and, hence, critical melting step for the production of a sound, segregation-free ingot for the manufacture of alloys used in rotating components in aircraft engines. A mathematical model for this process has been developed by the Specialty Metal Processing Consortium (SMPC). The model predicts temperature distribution in the solidifying ingot, flow in the molten metal pool, and the electromagnetic field in the ingot. These predictions may be used to estimate the effect of melting parameters on the pool profile in the ingot. In this paper, typical pool shapes and flow fields during VAR of Alloy 718 and Ti-6Al-4V are presented. The differences in the pool profile are primarily due to vastly different melting conditions. The model predictions are compared to the observed pool shapes from industrial-size VAR ingots.1. IntroductionVacuum Arc Remelting (VAR) is a process in which an electrode is melted in vacuum by the heat from a DC electric arc. Metal droplets from the electrode fall into the molten metal pool, which solidifies in a water-cooled copper crucible to form the ingot, as shown in Figure I. The ingot obtained from VAR is sound, and has superior cleanliness and chemical homogeneity. Hence, the process is the final melting process for most nickel-base superalloys and titanium alloys used in the manufacture of critical rotating components (discs & blades) of aircraft engines. Modeling of this process provides an insight into the effect of melting parameters on the molten metal pool in the solidifying ingot, which is a key first step in process optimization and defect prevention. In this paper, typical pool shapes, both measured and predicted, for VAR of Alloy 718 and Ti-6Al-4Vare presented. Alloy 718 is the most common VAR-processed nickel-base superalloy; whereas Ti-6Al-4V is the ''workhorse"" alloy for titanium-based alloys."

Jan 1, 2004

By V. B. Chernyavsky, Ladokhin S. V.

Equipment and continuous casting technology for the production of small diameter copper rods and tubes are described. Industrial copper wastes, such as scrap and shavings, were used as the charge. An electron-beam installation for rod and tube production includes a crucible with an electromagnetic stirring system and a pouring hole in its bottom, a bottomless mold, .and a special cooling system, which includes an oil and water cooling devices. For the first time in the electron-beam technology, rods of 8 mm and 14 mm diameter mm tubes of 14 mm external diameter and 7 mm internal diameter were produced through continuous casting by pulling them out of the vacuum chamder into the atmosphere with depressurizing the vacuum chamber. The production capacity of a single strand continuous casting machine was 200 mm/tnin for rod casting and 150 mm/min for tube casting.

Jan 1, 2000

By C. M. Egert, S. Rajic

"We have developed a monolithic micro-spectrometer suitable for a variety of sensing applications including industrial process monitoring. The device consists of a solid structure with a volume less than 6 cubic centimeters. All optical components of the spectrometer including two aspheric mirrors, a diffraction grating, and entrance and exit surfaces are fabricated onto the surface of the structure. All light paths are internally contained within the structure. The result is a small, rugged spectroscopic sensor ideally suited for use as a process monitor. Due to its monolithic nature the device requires no post-fabrication alignment; nor can it be knocked out of alignment during use. Although many materials and thus wavelength regions were possible, the prototype device discussed here was produced in PMMA by precision diamond turning. However, lower cost manufacturing approaches involving injection molding are under development to produce an affordable sensor.Due to its rugged monolithic design, small footprint, and low cost the monolithic micro-spectrometer is ideally suited for distributed monitoring applications often required for industrial processes. It is expected that modified versions of this sensor designs will be required for specific applications so as to maximize the performance and resolution over the operating range. For example, the prototype device described here operates over a wavelength range of 500 nm to 1000 nm. The performance of this device as a real-time surface monitoring sensor will be discussed in detail. Our approach of using wavelength dependant scattering resulted in the reduction to practice of a miniature, monolithic, rugged, low-cost, micro-instrument in a sensor sized package. The process sensor applications community has been faced by the cost versus performance issue. Simple go/no-go sensors are typically inexpensive but they provide very limited and sometimes dubious data. Scaled down traditional instruments offer very good measurand information but are typically cost prohibitive, fragile, and still relatively large. This work will bridge the gap between these two extreme sensing alternatives."

Jan 1, 1997

By Cz. Mazanek

Specific biostimulating and anticancerous properties have been observed in peat, Ash Vacanta, and in an amorpous silica that is obtained as a by-product of alumina production from Turow clay in Poland. The anmphous silica was characterized and found to have a large specific surface area. This property may account for the beneficial characteristics of the material.

Jan 1, 1989

By Ko-ichiro Ohno

It is recently recognized that the iron reduction and melting as well as the slag separation of a composite of granular iron ore and coal are completed in a very short period of about IO minutes when the composite is rapidly heated up to approximately 1673K. These phenomena are expected to be applied to a new iron-making process. The mechanism of iron ore reduction and iron-slag separation during rapid heating has not yet been revealed and the fundamental research has just started. Carburization of the reduced iron is regarded as one of the most important steps in this process. In the present work, the composite was prepared from four kinds of coal or graphite as a carbon source and electrolytic iron powder as a completely reduced iron ore. The temperature at which the liquid formation and iron carburization occurred was monitored. Direct observation of smelting reduction behavior was made by a confocal laser-scanning microscope combined with the infrared image-heating furnace to clarify the effect of molten ash on iron carburization. It was found that the meltdown temperature of composite became lower as the melting temperature of coal ash decreased. From the observed result, it was presumed that the liquid slag would act as an important media for the carbon transfer from coal to iron. The carburization mechanism during the smelting reduction was estimated as follows. When slag containing iron oxide melted down and contacted carbon, iron oxide in the slag was reduced and the formation of the metallic iron particle as well as the its carburization occurred simultaneously at the slag-carbon interface. Carburized iron particle was carried from slag- carbon to slag-iron interfaces due to the slag convection flow caused by the difference of the interfacial tension between the carbon-slag and iron-slag interfaces. Carburization of reduced iron could proceed with a repeat of the above-mentioned process.

Jan 1, 2003

By Peter K. Liaw, Charlie R. Brooks, David C. Joy, Wei Zhao

In this paper, effects of oxidation, porosity and fiber-fabric stacking sequence on flexural strength of a continuous silicon carbide fiber (SiCr) fabric-reinforced SiC ceramic-matrix composite (CFCC) were studied. The failure mechanisms were correlated with flexural strengths of CFCC samples, both before and after oxidation. Microstructures and fractography were investigated using scanning electron microscopy (SEM). The chemical change after oxidation, such as Si, C, and 0, and their distributions, were detected by the SEM energy-dispersive X-ray spectroscopy (EDXS) line-scan chemical analysis technique. These effects on the strength of the CFCC can be attributed to following reasons: (i) The decrease in the flexural strength after oxidation is mainly due to degradation of the strength of Nicalon fibers and the damage of fiber/matrix interface both caused by high-temperature chemical reactions, (ii) Porosity is not too important in affecting the strength of the CFCC, when the bonding of the forced flow chemical vapor infiltration (FCVI)-SiC matrix is stronger than that of the fiber/matrix interface. However, a higher porosity content will be harmful, because higher porosity will both decrease the effective elastic modulus of the FCVI-SiC and make pore-linkage easier to occur, which is more likely to cause premature failure, (iii) The variation in the lamina stacking sequence of the CFCC changes the elastic stress distributions along the thickness direction of specimens, the magnitude of ceramic matrix-cracking stress, the effective elastic moduli of the laminate, and different crack initiation sites as well as different failure modes, and thus, leading to the scatter in the flexural strength of the CFCC.

Jan 1, 1998

By Gervais Soucy

During mineral and industrial processing, contaminated wastewater can be generated such as cyanide liquors (free species or in complex form). This paper presents the treatment of cyanide solution derived from the aluminum industry, by direct contact of the solution with thermal plasma in a novel reactor. The reacation energy is provided by a plasma submerged in solution which allows direct contact between the plasma and the solution to be treated. The scope of this' study was to determine the feasibility of treating free and complex cyanides in solution through mini-pilot scale operations. An innovative reactor was designed and fabricated to provide stable: process operating conditions. Many parameters were studied. These experiments permitted the evaluation of the kinetics of complex cyanides decomposition under thermal plasma conditions. At atmospheric pressure (temperature about 100°C), the rate of cyanide decomposition by thermal plasma was 12 times greater than that of thermal hydrolysis in a plug flow reactor et the same temperature. The improvements in the decomposition rates are attributed to high thermal gradients at the plasma liquid interface and photocatalysis induced by the plasma UV radiation.

Jan 1, 1998

By Guo Chen, Jin Chen, Jinhui Peng

In this paper, solving common problem of electrostatic precipitator (ESP), which was frequently ruptured of the cathode insulation in the production process were studied. The microwave heating airflow technology was introduced, which takes full advantage of its unique properties, solves the output problem of the high temperature air, achieves purpose of energy conservation, important economic significance and environmental significance. The mathematical models and designing of microwave high-temperature hot air system was calculated. The common forms of heat exchangers and comparative analysis were also introduced. The conditions found to be at the temperature of 240 °C. Under optimum conditions, the microwave heating power was 1482 W. Based on the mention results, this microwave heating method can be applied effectively and efficiently way for the production process of electrostatic precipitator.

Jan 1, 2015

By Toshihide Takenaka, Takashi Matsui, Nao Murakami, Masahiro Kawakami

"Electrowinning of Ti have been investigated in a LiF-NaF-KF melt including K2TiF6 at 773-923K by applying electrochemical oxidation ofH2 gas as an anodic reaction. The cathodic behavior of titanium and the anodic behavior of H2 gas were studied by voltammetry in detail to clarify the electrolytic condition for the process. The electrowinning of Ti was carried out by potentiostatic _electrolysis. Steady electrolysis was achieved under the suitable electrolytic condition without breaking out the anode effect. Titanium metal was electrodeposited on a Ti cathode though the deposits were usually powdery. It is concluded that this process is potential if the morphology of the deposit can be improved.IntroductionTitanium has such good properties as high specific strength and high corrosion resistance. However, the availability of Ti has been limited because the price of Ti is much higher than those of other common metals, such as Fe and Al. The production process of Ti ingot from its ore is rather intricate so that the production cost is high. If the simpler process is developed, the production cost should be retrenched. Titanium metal is usually produced by the Kroll process, which consists of the electrowinning of Mg metal in molten salt and the chemical reduction of TiCl.i by Mg metal. The Kroll process is very elabrate, but not simple. Because the chemical reduction ofTiCl4 by Mg metal is highly exothermic, a considerable amount of energy is wasted.Titanium metal can be electrowon in molten salt bath in principle. A simpler and more effective process than the Kroll process may be realized by the direct electrowinning so that the electrowinning of Ti metal has been studied widely[ 1]. Some researchs progressed to a pilot plant stages [2], but the electrowinning of Ti has not been industrialized yet."

Jan 1, 2000

By Junji Shibata

Extraction behavior of Ti(IV) and other metal ions, such as Fe(III), Fe(II), Cu(II), Zn(I1) and Co(I1) from acidic solutions like sulphuric acid and hydrochloric acid was studied in order to recover titanium from the waste solution in Ti02 production. Extractant used was tri-alkyl phosphine oxide whose trade name was Cyanex 923. Then, a study was made of the idea of simulating a countercurrent multistage extraction system, using the results of batch extraction. The simulation was camed out on extraction and saipping behavior for a Ti(1V)-H$O,-Cyanex 923 system. From the simulation result., the optimum operating condition of the system was considered.

Jan 1, 1994

By Tangstadm Merete, Eli Ringdalen

"This paper presents an overview of results from The Norwegian Research Institution SINTEF and the Norwegian University of Science and Technology, NTNU regarding new and ongoing research in silicon production. The main studies are related to condensation of SiO gas and cavity formation. If SiO gas condensation is increased at the top of the furnace resulting in SiO content in the off-gas closer to equilibrium, the Si yield will be increased significantly. Experimental work, simulating a cavity under industrial conditions, has shown that the cavity grows downwards from one layer. Physical appearance of zones in industrial furnaces, and selected reactions in these, are discussed based on results from excavation of industrial furnaces and results from laboratory experiments. Experimental studies of reaction rates for the formation of SiO are presented. Quartz properties are demonstrated to vary between differing quartz types and the effect of this is discussed.Introduction Both the theoretical and industrial issues associated with the production of silicon are described in detail in the textbook written by Schei et al [1]. This book covers the knowledge of silicon production process up to 1998. Together with the work by Myrhaug [1] and by Aasly[2], this is the main basis for this paper. Recent and ongoing research at SINTEF and NTNU focusing on production of Si and SiO in the high temperature zone, dissociation of SiO and condensate and cavity formation will be discussed."

Jan 1, 2012

By Milan Lj. Stamatovic

The hydrometallurgical recovery of zinc from recycled blast furnace dust from a steel plant (Smederevo Metallurgical Company, Yugoslavia) was investigated. The dust contained 22% Fe, 17% Zn and 0.2% Pb. X-Ray diffractometry showed that the main components were hematite and magnetite, in combination with zinc oxide. Individual particles were generally spherical and ranged in size from 10 to 150 microns; 63% were less than 33 microns in diameter. An effective hydrometallurgical approach proved to be by caustic leaching and electrowinning. Recovery of zinc in the form of zinc powder was over 90%; this material can be used for the cementation of impurities in the conventional hydrometallurgical process for zinc production.

Jan 1, 1994

By Björn Lindquist

Boliden has developed a number of specialised technologies for smelter gas handling and effluent treatment. These technologies will be described. Special attention will be given to the high-pressure venturi, Editube wet electrostatic precipitator, mercury removal processes, and two-stage effluent treatment.

Jan 1, 2002