Search Documents

By Xiaobing Yang, Animesh Jha, Greg Doughty

"Successful use of inert anodes should reduce the CO2 footprint in aluminum production. The search for a “holy grail” inert anode for metal electro-winning from constituent oxides using molten salt bath as an electrolytic medium is continuing. In this article we demonstrate the engineering approaches for the fabrication of intermetallic anodes, based on a quaternary Al-Ti-Cu-M (M:Ni, Fe) system for primary aluminium production. In particular, we examine the microstructural and electrochemical properties of alloys, based on the quaternary compositions. We explain the aspects of phase stability under anodic potential, which leads to the loss of anodic materials in the temperature range of 850-1050oC. The results are analysed in the context of oxidation reaction and formation of oxide layers which readily dissolve in the cryolite melt and prevent passivation. The paper also describes the conditions under which the reduction of aluminium at the graphite cathode occurs which also strongly depends on the molten salt chemistry for the nucleation of molten aluminium at the cathode.1. IntroductionOxygen-evolving inert anodes are an alternative to the conventional consumable carbon anodes for the production of primary aluminium. In this paper the materials selection criteria chosen for the engineering of anode is based on the understanding of the thermodynamic stabilities of aluminide intermetallic phases, some of which are formed and remained stable in fluoride melts. For example, the formation Al3Ti dispersed in aluminium metal via molten-fluoride flux reaction is well known in the context of aluminium casting and grain refining [1-3]. It is for this reason in our research we concentrated on the engineering of stable intermetallic phase mixture in the Al-Ti-Cu ternary system, shown in Figure 1 [4]. In this figure two compositions in the Al3-0.5zTi1-0.5zCuz family are shown with the substitution of 7 atomic % and 11 atomic % copper. However initial investigations showed that these two compositions were unsuitable due to the formation of low-temperature liquid (~540oC) and intermetallic phase, Al2Cu along the Al-Cu binary edge during solidification. The Al2Cu phase segregated along the boundaries of Al3Ti and Al5Ti2Cu, and dissolved away when electrolysis was carried out using these anodes above 800oC. The presence of consequential porosity in the anode material increased the corrosion of the alloy through local heating due to high current density at 0.8 A cm-2. The early tests were carried out with cryolite melts, shown in Figure 2, having 3 weight percent of Al2O3 in the bath at 850oC."

Jan 1, 2010

By Thomas M. Harris

Cation exchange is not sufficiently selective to be used for the removal of heavy metal ions from a general industrial wastewater. However, if the metals can be converted to polyvalent anions through complexation, they may be removed both selectively and efficiently by anion exchange. This approach, referred to as chelation-assisted anion exchange (CAAE), has been examined using industrial wastewater samples contaminated with Ni2+ and Cr3+. For this particular application, the Ni2+ is complexed with 8-hydroxyquinoline-5-sulfonic acid, and the Cr3+ with sulfosalicylic acid. Removal efficiencies and adsorption isotherms for both the complexants and the complexes were determined in batch-mode tests.

Jan 1, 1994

By David Forrest

In 1981, K. E. Drexler proposed using massively parallel nanomechanical systems to manufacture large atomically exact structures. As in macroscopic mechanical systems, they would contain components that serve traditional functions such as trusses for support, gears to transmit power, bearings for low-friction support of rotating surfaces, motors to supply torque, pipes and conveyor belts for material transport, and channels for coolant. Many of these components would only contain a few thousand atoms. Specific designs for these devices became available in the early 1990s, and a few working devices appeared in laboratories by the early 2000s. As advances continue, a thorough understanding of the operative transport phenomena will guide the intelligent design and construction of nanomechanical structures, devices, and systems. The familiar equations of continuum mechanics are generally inadequate to describe the flow of heat and mass in the proposed nanosystems. Boundary conditions often need to be described in terms of potential surfaces. Surfaces are not geometrically smooth, but periodic according to the locations of atomic nuclei. Friction occurs not due to the plastic deformation of asperities on mating surfaces, but to phenomena such as thermoelastic damping and phonon viscosity when atoms slide past each other. Electrostatic forces dominate over gravitational forces by orders of magnitude; there is no role here for natural convection. Structural components, no matter how stiff and strong, are in constant motion due to the thermal noise in the system. The fluids are described in terms of individual molecules in constant motion.

Jan 1, 2006

By Sergei A. Degterov

A thermodynamic database for the slag, matte and liquid copper phases in the Cu-Ca-Fe-Pb-Zn-Si-O-S system has been developed for the ranges of compositions of importance to the production of copper. When used with the Gibbs energy minimization software and other databases of the F*A*C*T thermodynamic computing system, this database will permit the calculation of matte-slag-copper-gas phase equilibria that take place during copper smelting and converting. The calculations reproduce within experimental error limits all available experimental data on phase diagrams, activities of components, enthalpies of mixing, matte - alloy miscibility gap and tie-lines. The calculated solubilities of Cu in both S-free slag and slag equilibrated with matte are also in good agreement with experiment under all studied conditions, such as at SiO2 saturation, in equilibrium with Fe, Cu or Cu-Au alloys, at fixed oxygen or SO2 partial pressures and at different contents of Pb, Zn and CaO in the slag. Sulfide contents (sulfide capacities) of the slags are predicted within experimental error limits. The distribution of Pb and Zn among matte, slag, copper and gas has been calculated. The calculations are in good agreement with experimental data and predict the distributions under conditions which are difficult to study experimentally, such as at magnetite saturation or under various oxygen partial pressures and iron to silica ratios in the slag.

Jan 1, 1999

By R. N. Reddy

The Pseudo capacitance of layered type Mn02 electrode material for electrochemical capacitors (EC's) was investigated. MnO2 was synthesized in our laboratory. Mn02 was prepared from heating of KMn04 at 300°C in air. Cyclic Voltammetry (CV) experiments were carried out using three electrode system, Saturated calomel electrode as reference electrode, platinum mesh as a counter electrode, and MnOz composite material mounted in a platinum mesh used as a working electrode. Two kinds of composite working electrode materials were used, one was mixture of MnOz and 25 wt% acetylene black, while the other was MnOz, 25 wt% acetylene black and 25 wt% carbon. All the experiments were carried out at 25OC. A maximum specific capacitance of 130 Fig and 118 Fig were observed at the scan rate of 2 mV/s and 20 mV/s respectively in 1M KC1 for composite electrode made with carbon. Results obtained in this study are compared with that of other electrode materials.

Jan 1, 2002

By Julien Favre, Akihiko Chiba, Damien Fabregue, Yuichiro Koizumi, Eric Maire

"The mechanical behavior of Co-20Cr-15W-10Ni alloy is studied by compression tests at high temperature. Microstructures after deformation are evaluated using SEM-EBSD. Significant grain refinement occurs by dynamic recrystallization for high temperature and low strain rate (T>1100°C, <0.1s-1), and at high strain rate (~10s-1). Dynamic recrystallization is discontinuous and occurs by grain boundaries nucleation, leading to a necklace structure. The nucleation mechanism is most likely to be bulging of grain boundaries. However, recrystallization occurs also by rotation of annealing twins which can bulge as well. The modeling of mechanical behavior gives a fair quantification of flow softening due to dynamic recrystallization, indicating the progress of dynamic recrystallization with deformation.IntroductionCobalt-chromium alloys are used in biomedical applications for the elaboration of implants due to their outstanding mechanical properties and their high resistance to corrosion. For stent application a large ductile behavior is required in addition to the high mechanical strength. Indeed stents have to undergo a deformation until e˜40% during their expansion [1]. Conventional Co-Cr-Mo (CCM) alloys exhibit limited ductility (maximal deformation about e˜30%) [2]. Co-Cr-W-Ni (L-605) alloy is a better candidate for stent elaboration since its fracture strain can exceed 40% (comparable to nickel superalloys (Figure 1), while it keeps high mechanical strength. In spite of the presence of nickel element in this alloy, biocompatibility is sufficient for vascular implants, therefore L-605 alloy is extensively used for heart valves and stent elaboration [3]."

Jan 1, 2012

By Antonio Luraschi

The constituents iron, oxygen, silica and cop- per are of principal interest in slags utilized in pyrornetallurgical processes for producing copper. Accordingly, phase relationships in the.Cu-Fe-0-SiO2 system are important when one considers the physico- chemical behavior of slags. These phase relation- ships for the quaternary and constituent ternary systems are developed from available information. Isothermal composition and composition-oxygen potential diagrams, and oxygen potential-temperature diagrams are utilized to describe the&apos; important relationships.

Jan 1, 1976

By R. J. McClincy

The potential techniques for the direct smelting of copper sulfide concentrates to blister copper were evaluated from the standpoint of commercial application. Many existing smelters are adaptable to direct smelting practice but only with improved control of metallurgical performance. Modified and innovative procedures for slag cleaning and metal refining, prerequisites to direct smelting, are presented and discussed. The ability to smelt directly to blister copper using existing equipment and eliminating the need to convert matte offers ,significant advantages to traditional smelting practice from the viewpoint of cost, &apos;S02 control, and process simplicity.

Jan 1, 1983

By Andressa A. Silva, Esperidiana A. B. Moura, Francisco R. Valenzuela-Diaz, Jorge N. Sales

This work aims to study the influence of the nanoclay Cloisite 20A incorporation on mechanical properties of ABS (acrylonitrile butadiene styrene). The incorporation of Cloisite 20A was made in two steps; firstly,a masterbatch was preparated and then, it was incorporated in ABS. The Cloisite 20A masterbatch using 40 % of nanoclay and 60 % of SAN (Styrene Acrylonitrile) was prepared in an adiabatic mill. After that, Cloisite 20A masterbarch at 1 and 5 % (wt) was added in ABS. The resulting nanocomposites were characterized by tensile tests and the correlation between properties was discussed.

Jan 1, 2015

By Jing Zhan, Chuanfu Zhang, Yonglin Yao

"The Ni/Co arbitrary ratios of fibrous precursor were investigated during coordinated coprecipitation by changing the precipitating medium. The results show that the original molar ratio ofNi2+ to Co2+ in reaction solution can be maintained in the coprecipitate at pH'.'05.0 and the coprecipitate is single phase solid solution using water and water-X precipitating medium. But the original Ni/Co ratios are no longer kept and composition of the coprecipitate is not uniform at pH>5.0 in water precipitation medium. In order to obtain the precursors with the required morphology and accuracy Ni/Co ratios, the optimum conditions of fibrous precursors were chosen as follows: ammonia used as complex agent and pH adjustor, water-X solvent as precipiting medium, oxalate as coprecipitated agent, 8.0-8.4 for pH value, 50-70°C of reaction temperature, 0.5-0.8 mol/L of initial nickel and cobalt salt concentrations and excesses of oxalic acid of 10% - 20%.IntroductionNi-Co alloy as an important transition metal alloy with high mechanical strength, good anti-deformation, corrosion resistance, thermal conductivity, thermal stability, electrical conductivity, electrical contact, and special magnetic properties indicates that it can be used as high-temperature catalyst, special magnetic material, high-temperature electrochemical devices, and so on [1-6]. An ideal composite powder should have an appropriate stoichiometric ratio, good uniformity of chemical composition, appropriate phase, low impurity content and small particle size [7]. Similarly, the composition of nickel-cobalt alloy powder has an important impact on its crystal structure, properties and applications. Guo[8] found that magnetisms of CoxNi1-x such as magnetic anisotropy, curie temperature, and the shifts of the spin steering are very sensitive to the composition of alloy powder."

Jan 1, 2013

By Emanuel Negrao Macedo, Edinaldo Cunha, Mauro Oliveira, Jose Antonio da Silva Souza

"This paper presents the study of the increasing addition influence of the bauxite waste in some properties of polymeric matrices composites reinforced with natural fiber: Curaua (Ananas Erectifolius smith). There were evaluated properties as density, tensile and flexural resistances. The high pH provided by the waste is used as hydrolysis agent, providing the pectin cement dissolution of the fiber bundles, and therefore, improving the mechanical adhesion in the fibermatrix interface and the increase of the fiber bundles aspect ratio. Furthermore, the content of silico-aluminous material in the waste provides increase in the composite abrasivity, which is destined to civil and naval construction. The fact of being a low-cost and highly available waste turns the red mud in a high potential material as polymeric composite filler.IntroductionRed mud is an insoluble residue, originated from the bauxite refining through the Bayer Process [1]. It is an Iron Oxide rich material [2] (substance responsible for the red brick color), it has a complex chemical composition [3], and its composition is highly dependent of the type of bauxite used in the process [4]. It has high alkalinity (pH= 10 - 12.5) and a very small solids size distribution (95% diameter< 44µm) [1], what turns the red mud a serious environmental pollutant.The utilization of fillers on composite materials is done after many necessities; however, one of the major necessities is the cost reduction [5]. Furthermore, mechanical and thermal properties of polymers usually are improved by the addition of inorganic fillers [6], being an example of this improvement the reduction of the flammability of polymer matrixes due to the addition of functional clays [7]. In this way, the red mud becomes potential filler for composites, since cheap and easily available fillers (like red mud) are a good option to reduce costs [8]."

Jan 1, 2013

By Anne C. Chinellato, Alejandra T. Soria, Nelida L. del Mastro, Amanda C. S. Pereiral, Esperidiana A. B. Moura, Anibal V. Abreu

"This work presents a comparative study of the thermo-mechanical and morphological properties of sugarcane bagasse fiber/HDPE composite treated with electron-beam and gamma radiation. The composite samples obtained by extrusion and injection molding processes were irradiated at 50 and 90 kGy using either a 1.5 MeV electron beam accelerator or gamma irradiator EMI-9, at room temperature in presence of air. The irradiated and non-irradiated samples were submitted to mechanical and MPI tests, differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), scanning electron microscopy (SEM), sol-gel analysis and X-Rays Diffraction (XRD) and the correlation between their properties was discussed. Improvement of the bagasse fiber/HDPE composite properties, using electron-beam or gamma radiation, was found.IntroductionResidues of sugarcane bagasse fiber are widely produced in Latin America and other countries: in Southern Africa, Egypt, South-Eastern Asia, India, China, Australia, Cuba, among other producers, as by-products of the sugar and bioethanol industry. The sugarcane industry in Brazil and Uruguay is well established and expanding with large potential to increase the production of sugarcane bagasse in the next years [1-3]. Although the major portion of the bagasse is currently burnt for energy supply in the sugarcane industry, the disposal of this byproduct is still inefficient and, consequently, it is critical for agricu1ture profitability and environmental protection. Sugarcane bagasse is a lignocellu1ose fiber mainly constituted by around 46 % cellu1ose, containing hemicellu1ose, lignin, fat and waxes, silica and other elements [3, 4]. Studies have reported that sugarcane bagasse can be used to produce thermoplastic polymeric composites with excellent properties for many applications. [5-8]. Based on this survey, the transformation of bagasse into high quality industrial products, such as bagasse-polymer composites, can provide its more effective utilization."

Jan 1, 2012

By T. Shibasaki

There is a strong demand in the photo industry to the higher quality of refined silver. Osaka Refinery produces about 27 mtpm of refined silver mainly from copper refinery slimes. Product quality is attained by controlling the impurity level in electrolyte. Copper is cemented with silver oxide and palladium is precipitated by a chelating agent. Both processes were operated previously in batchwise for treatment of bled out electrolyte, Recently these processes have been improved and made continuous to cope with the increased impurity.load. As a result the grade of fine silver has been maintained steadily at Pd < 3 ppm and Cu < 5 ppm.

Jan 1, 1989

By Luiz A. Teixeira

This paper reports the results of kinetic studies involving the precipitation of arsenic from aqueous solutions as FeAs041 Fe(OH)3&apos; using FeS04 as source of Fe ions, and Air or H202 as oxidizing agents. Both systems lead to an efficient removal of arsenic. The differences in oxidants performances are in the precipitation reaction rate -much faster using hydrogen peroxide. Mechanisms of reactions were suggested based on the following main steps:

Jan 1, 1996

By Robert W. Bartlett

Chalcopyrite in copper flotation concentrates can be hydrothermally converted to digenite with oxygen in a continuous process, with rapid kinetics when operated above 200°C. This eliminates large amounts of sulfur and iron. These "super-concentrates" have potential for debottlenecking smelters and avoiding capital intensive future smelter expansions, otherwise required in the late 1990s. The technology of producing super- concentrates is described, with cost estimates, and the use of super-concentrates as smelter feed is discussed, with examples.

Jan 1, 1992

By Robert L. Opila

Negative electrodes for alkaline nickel-metal hydride batteries composed of MmNi3.5Al0.8Co0.7, where Mm is misch metal, have been characterized electrochermically and using x-ray photoelectron spectroscopy. The stability and rapid hydriding and dehydriding kinetics of the alloy in KOH are attibuted to a surface film. The protective surface film is shown to consist of an porous, outer hydrated layer and a dense, inner oxide layer. In addition, metallic nickel and cobalt are found throughout the film, and are presumed to form a conductive, percolative network that permits rapid electron transfer from the bulk to the solution, allowing rapid electrochemical formation of atomic hydrogen.

Jan 1, 1997

By Martin J. Hansel, Jan Bäckström

Starting from historic perspectives on converting at the Rönnskär Smelter, the continuous developments of refractory practice is described. In the development the joint efforts of operators and suppliers of refractory have lead to significant achievements. This paper comprises the development of the converting process and the refractory lining as well as future prospects regarding operation and refractory lining design, especially in the face of equipment and raw material availability. 81

Jan 1, 2009

By J. Markussen

The Falconbridge Matte Leach Plant was based on leaching Ni-Cu matte with strong hydrochloric acid in rubber lined equipment. It operated from 1968 to 1983 as a precursor to Nikkelverk&apos;s present C12 Leach. The process comprised two S.X. systems. NiC12.4H20 crystallization, crystal drying, NiC12.H20 pyrohydrolysis and HC1 gas recovery. The naphtha fired fluid bed pyrohydrolyzer produced granular NiO, subsequently reduced with H2 to granular nickel for sale. The development and operation of the pyrohydrolyzer are described

Jan 1, 1991

By M. Cloete, C. MacLagan, A. Newall

This paper initially gives a brief overview of Zinc Corporation of South Africa Limited (Zincor). The original design parameters of the Zincor roasters are compared to the current operation, and the requirements for efficient roasting are listed. Roaster operational problems experienced during the early to mid 1990's are outlined. A description of the investigation and the outcome to increase overall roaster availability are given. The history and the development of the use of oxygen at the Zincor roaster operation, with an account of the associated operational experiences, are explained.

Jan 1, 2000

By Ting Lei, Mingjun Rao, Guanghui Li, Tao Jiang

"With the rapid development of iron and steel industry, the supply of iron ores can not meet the present demand for iron and steel industry in China. Large reserves of oolitic hematite have been discovered with low iron grade (30% ~ 45%) and high phosphorus content (0.4% ~ 1.8%). Traditional processes for utilization of this ore are characterized as either high cost or low dephosphorization. In this study, sodium salts-modified paigeite (SSMP) was added to enhance on the dephosphorization of high-phosphorus oolitic hematite by using reduction roasting followed by magnetic separation. Various parameters, including the amount of SSMP, reduction time,reduction temperature, grinding fineness and the magnetic field intensity were investigated. As a consequence, a magnetic concentrate of metallic iron powder with total iron grade of 93.2% and phosphorus content of 0.08% was obtained under the optimal conditions. The results also provide a potential avenue for the comprehensive utilization of paigeite ore.IntroductionOolitic hematite is currently recognized as one of the most refractory iron ore resources in the world. Over 4.0 billion tons of reserves of such resources have been found in China, and more than 10 billion tons in the long-term. This kind of ore is characterized as low iron grade (30%~45% TFe) and high phosphorus content (0.4%~1.8% P), as well as fine particle size distribution of ferrous minerals (the size distribution varies from 5~30 µm, even less than 2 µm) and the complex association between iron and other gangue elements [1~5]. The unique structural characteristics of the high phosphorus oolitic hematite make it difficult to obtain high iron recovery and good dephosphorization efficiency by using the conventional processes [1,2]. Traditional processes are characterized as high cost and low dephosphorization for oolitic hematite beneficiation [9~15]."

Jan 1, 2012