Search Documents

By Forrest T. Moyer

[The safety record of the nonmetal mining industry during 1965 way worse than that of 1961 in all general measures s of injury experience except for a slight improvement in the number and frequency rate of nonfatal injuries Work fatalities in 1965 totaled al and occurred .it a frequencyrate of 0.29 and a severity rate of 1,711 per million man-hours of worktime. The fatality total was seven oven higher than to 1964 and the injury ratess increased d 32 and 28 present, respectively Thin total. of 2,172 nonmetal injuries u- in 1965 was 3.4 less than in 1964 and the frequency rate per million ion man-hours worked declined percent to 22.73 from: 23.14 in 1964. However, the 1965 nonfatal severity rate of 1,339 per million man-hours worked was 15 percent our the: d.96,1 rate of 1,160, This increases was largely attributable to two more permanent total and nine more permanent partial injuries. in 1965 than in the proceeding year. The average severity all injuries in 1965 was 132 days, 1-I. or charged per injury or 25 days more than in 1961. Injury experience in the nonmetal mining industry, including and excluding officeworkers, for the a-year period 1961-65 is shown in table 1. The average number of men working, on active days in 1963 was 48,429, or 635 fewer than in 1961. However, mines and mills, wore active an average: of 5 days more for a total of 277 in 1965, and each worker averaged 2,245 hours compared to 2', 190 hours in 1961. As a result, aggregate worktime of 108.7 million man-hours increased 1 percent over the 1964 total of 107.4 million hours.]

Jan 1, 1970

By M. G. Wallis

This report presents the results of a study to develop a detailed mining method design based on longwall mining with sublevel caving. The method is applicable to low-dipping coal seams 20 or more feet thick such as are found in the western United States. The report covers (1) the development and description of the mining method, (2) evaluation of the engineering feasibility of the design, (3) estimates of productivity and recovery, and (4) an engineering cost analysis and economic feasibility evaluation of the mining method design.

Jan 1, 1977

By Ernest A. Hersam

"INTRODUCTION.Luring the year 1923 a complete survey was made of the condition of research in the reduction (milling) and concentration of ores and nonmetallic minerals - that is, up to the stage where the ores or concentrates were ready for hydro- or pyro-metallurgical treatment. This survey was carried on under the general supervision of L. A. Lyon, assistant director and chief metallurgist of the Bureau of mines, in cooperation with the milling committee of the American Institute of mining and metallurgical Engineers, the Massachusetts Institute of Technology, and the University of California. Other institutions, including the National Research council, were of assistance and outlined recommendations during the study.While this report is on ""ore dressing"", it contains short sections on coal and clay. The mechanical handling that these minerals undergo is ""dressing"", so that ore dressing is inclusive of metallic and nonmetallic minerals. ""milling"", in its broadest sense, includes with ore dressing certain other metallurgical treatment which the report is not designed to cover.The survey revealed that considerable experimentation is being carried on great cost to the mining industry, but that the research is in general poorly coordinated while companies and firms are adequately taking care of routine tests and the mechanical features involved in their own operations, no comprehensive study of the fundamental principles of ore reduction is now in progress or contemplated. Many industries, besides mining, are interested in the preparation of materials for final treatment, rendering this investigation of value also to them. This class of fundamental research is neglected by industry unless there is some agency which can bring together at least a majority of this interested in a cooperative effort. It can not be effectively handled by a single company; and, moreover, no company can be expected to bear the whole burden of an investigation to benefit the entire industry or a number of industries hence there is need for concerted study within reasonable limits. Furthermore, co-operation eliminates duplication, which is largely a waste of effort and capital."

Mar 1, 1925

Martin Marietta Aluminum, Inc. followed Howmet Aluminum Corp., Revere Copper and Brass, Inc. and Anaconda Co. in lifting August prices of 99.5 percent unalloyed aluminum ingot by 3 cents to 56 cents per pound. Prior to these moves, Kaiser Aluminum and Chemical Corp. raised its June ingot listings by 4 cents to 57 cents and Consolidated Aluminum Corp., 4.5 cents to 57.5 cents. Domestic merchants increased July quotes by slightly more than 1 cent to 51.3-51.8 cents per pound. ARSENIC The Occupational Safety and Health Administration (OSHA) issued new standards, effective August 1, for worker exposure to inorganic arsenic, a toxic substance linked by OSHA to lung and lymphatic cancer. The new standard will limit worker exposure to 10 micrograms per cubic meter of air over an 8-hour period, a drastic reduction from the previous standard of 500 micrograms for a like period. Implementation of the new standards may be the most difficult and costly for copper smelters where arsenic is associated with the copper feed material but problems will also be encountered by producers of arsenic containing products such as for pesticides and herbicides. The new standards allow use of personal protective gear for workers as an interim measure until plant engineering controls can be put into effect.

Jan 1, 1978

Since early July, domestic producer listings in primary aluminum ingot have been at 53¢ per pound. Dealers, however, lowered their August quotes by 1.8¢-2¢ to 47.5¢-48¢ per pound. BITUMINOUS COAL AND LIGNITE -The wildcat strike of UMWA coal miners which began on June 23 in protest of cutbacks in medical benefits appears to have ended. According to the West Virginia Coal Association on September 7, 1977, all mines in West Virginia were back in operation on September 6 and again on September 7. The Kentucky Coal Association reported approximately 2,500 miners were on strike in eastern Kentucky on September 6, but there was full employment on September 7.

Jan 1, 1977

This report summarizes the results of a research project entitled "Fatal Accident Data Base Development." This project is the last project under Contract No. S0110601. Volumes I and 1I, "Industrial Engineering Study of Hazards Associated with Underground Coat Mine Production," summarize the original industrial engineering project and the Fatal Accident Report Analysis project. These projects were completed and accepted by the U.S. Bureau of Mines on December 10, 1971. Both volumes of the report have been made available by the Bureau to the public through the U. S. Department of Commerce technical information service. Another project under the same con tract, entitled "Equipment Operations Safety Study, ' was completed in January 1972 and the report was accepted by the U. S. B. M. at that time. The analysis in this Natal Accident. Data Lose Development report is closely related to analysis in both of the earlier reports. The original project involved an industrial engineering and safety of production operations for a representative sample of underground bituminous coal mines. The contactor was required to make recommendations 'in work practices, mining methods, equipment, and safety practices which can effectively reduce the fatality rate from rib and roof falls.' (Longwall mining methods were excluded from the study.) Time study and work element analyses were performed in over 50 mines as part of the field data gathering effort. Another requirement of the study was to develop sets of multiflow. Process charts, which are diagrammatic illustrations of the time-related interaction of mining, cycle job elements.

Jan 1, 1972

By John I. Kasteler, John H. Hild

"INTRODUCTION The South Hecla mine, one of the principal mines of the Alta United Mines Co., is situated at Alta in thee Little Cottonwood mining district, about 30 miles southeasterly from Salt Lake City, Utah. The mine has produced copper, lead, zinc, gold, and silver, and is reported to have been one 'of the principal sources of this country's bismuth from 1912 to 1925. The tungsten mineral, scheelite, has been found but has not been recovered. The extreme need for these minerals during World War II prompted an examination of the property by the Bureau of Mines and resulted in an unpublished report entitled ""The South Hecla Mine, Salt Lake County, Utah"" (fig. 1).A Bureau of Mines project 3301 was initiated, and operations were started early in 1943. The primary purpose of the project was to increase substantially the reserves of bismuth and tungsten ores. The critical situation in regard to lead, copper, and zinc developed during the early stages of the operation, and the work was expanded to include the development of ores 'of these metals.An investigation of 'the Albion, Rustler, and Greeley workings adjoining the South Hecla mine was made, and this work is also described (fig. 2); ACKNOWLEDGEMENTSIn Its program of investigation of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each investigative project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual investigative work, and prepares the final report. The Metallurgical Branch, O. C. Ralston, chief, analyzes samples and performs beneficiation tests."

Jan 1, 1948

Wildcat strikes in the Appalachian coal fields, primarily in West Virginia, have resulted in an estimated 4.5 million ton loss in coal production during July and through the first week in August. Since then, the strike intensified further, and on August 9, nearly all of West Virginia's 60,000 miners were off the job with another 10,000 miners on strike in eastern Kentucky. The Bureau of Mines estimates that West Virginia's coal output is currently (8/9) eight million tons below last year when the state produced 108 million tons. West Virginia, the Nation's second largest coal producer of coal behind Kentucky, has not failed to mine over 100 million tons a year since 1938. At the end of the second week in August, nearly all coal miners in West Virginia remained out. The strike is a protest against a cutback in union health and retirement benefits. An announcement June 23 about the United Mine Worker's health and retirement fund precipitated the strike, Fund directors said that because of inflation and production losses caused by earlier wildcat strikes and the severe winter, miners would have to pay the first $250 of hospital costs and 40 percent of doctor bills, up to $500 a year. Previously, the funds paid all hospital and doctor bills. According to the West Virginia Coal Association each day of the strike in West Virginia results in a loss of coal production of 500,000 tons, a loss of $3.8 million in miners wages and $1 million in contributions to the UMWA's health and retirement fund.

Jan 1, 1977

Since mid-July, most domestic producers have been marketing 99.5 percent unalloyed aluminum ingot at 53-57 cents per pound. Dealers in the United States have recently quoted ingot at 52.3-52.8 cents. On October 2, London Metal Exchange will trade aluminum, selling contracts on a cash and a 3-month basis. New York dealers were quoting August ingot at 52.3 52.8 cents. The Bonneville Power Administration announced that, effective December 20. 1978, electric power rates charged primary aluminum producers in the Pacific Northwest would be increased The increase (equivalent to about 4 cents per pound of aluminum produced) will raise the average rate to about 8.7 mills per kw-hr compared to 3.2 mills per kw-hr.

Jan 1, 1978

New Copper Deposit in Chile. - The recent copper discovery in Chile, made jointly by U.S.-owned Empresa Minera Utah de Chile, Inc., and Getty Mining Chile), Inc., awaits the passage of Chilean legislation which is expected to govern the terms of new foreign investment in the country's mining sector. Named La Escondida, the discovery is reported to have the potential for producing 100,000 tons of refined copper per year. This compares with Chile's total refined primary copper production in 1980 of 811,000 metric tons, and to U.S. refined primary production in 1980 of 1,122,000 metric tons derived from domestic material, and 89,000 metric tons from foreign material. U.S. Firms Buy Chilean Properties. - A bid of $18.1 million, made jointly by Chevron and St. Joe Minerals Corp., won over competing bids for the purchase of the Libra and Mena gold-silver-copper deposits in northern Chile. Chevron is the lead partner and owns 70% of the venture. The two properties purchased have not been developed to any significant extent. They are located near St. Joe's El Indio gold-silver-copper mine. The venture is also looking at the possible purchase of two other mines in the area.

Jan 1, 1981

Many of the difficulties faced by the U.S. mineral industry in 1982 and 1983 emanated from the worldwide recession, from the high value of the U.S. exchange rate, and, in part, from actions taken by foreign governments to protect selected industries. While some problems will be minimized with continued worldwide economic recovery, others remain and may require special attention by U.S. policymakers. These problems include declining U.S. production capacity in selected mining and mineral processing industries, the impact of the high value of the U.S. exchange rate, and protectionist trade practices by competitor nations. Illustrative of the last is the International Trade Commission (ITC) determination in June 1984 that both the domestic steel and copper industries have been substantially injured by foreign imports. In its July 1984 recommendations to the President, the ITC suggested higher tariffs and quotas for 5 years on 70 percent of steel imports but conditioned the aid on cost-cutting and modernization steps by the domestic industry. In the copper decision, two commissioners recommended increased duties, two recommended that quotas be imposed, and one recommended that no relief be provided. The President decided in September to seek voluntary restraint agreements with nations that export steel to the United States and rejected both quotas and higher tariffs on copper imports. General Economic Setting This decade opened with the U.S. mineral industries struggling to deal with double-digit inflation, record high peacetime interest rates, and almost 7 years of oil-cartel-induced energy price increases that seriously affected the profitability of energy-intensive industries such as mineral production and processing.

Jan 1, 1985

By C. B. Manula

This report is mainly concerned with the modification and development of a users manual for the Open-Pit Materials Handling Simulator (OPMHS) developed at Penn State. Model Modifications included the introduction of a free-format input, the application of a Weibull random generator, facilities to stochastically simulate shovel-dragline operations, and routines to increase the flexibility in making truck assignments. At the same time, core storage requirements and execution times were minimized and all P.S.U. conventions were removed to allow operation on other computing systems.

Jan 1, 1976

By Albert H. Fay

This glossary is publi~hed- by the Bureau of Mines as a contribution' to the mining literature in the belief that it will fill a long-felt need. It contains about 20,000 terms; these include both technical and purely local terms related to metal mining, coal mining, quarrying, petroleum, and natural gas, and metallurgical works; names of useful, important, and common minerals and rocks; an<lgeological terms. It presents in one comprehensive volume the available standard, technical terms relating to the mining and mineral industry, as well as provincialisms that have been or are now in use in English-speaking countries. The glossary also includes many terms relating to ceramics and the clay industry, glass making, foundry practice, railway and building construction, electrical installation and power-plant equipment, and chemical terms relating to metallurgical practice. Complete lists of terms for' each of these allied industries are beyond the scope of this glossary. Paleontological terms, although closely associated with geology, are far removed from mining and metallurgical operations, and for this reason have been omitted. In a compilation of this magnitude, it is difficult, within a reasonable time to verify all definitions as to the latest usage. Much verifying was done and it is hoped that the best and latest definitions have been used. Reference to the publications cited will enable the reader to determine approximately the period when the definition was used. Definitions in use by engineers of high national or international reputation are given first preference. When definitions from different sources are the same, credit is given to the earlier author as being the original or nearest to the original source. Immediately following each term the name of the locality wherein the word is presumed to have originated or is widely used is given, where such information is available. The name of the author or source from which the definition was obtained follows the definition, and serves as a key to the publications listed. The terms selected from the various glossaries and publications examined have been compared with the Webster,

Jan 1, 1920

Geophysical Abstracts 1 - 86 wore issued in mimeographed form by the Bureau of Mines; Abstracts 87 - 111 were published in bulletins of the Geological Survey; Abstracts 112 - 119 were issued in mimeographed form by the Bureau of Mines as Information it ion Circulars 7256, 7257, 7267, 7273, 7285, 7292, 7303, and 7310. 1. GRAVITATIONAL METHODS 7786. Barton, D. C.3/ Case Histories and Quantitative Calculations in Gravimotric Prospecting. Am. Inst. Min. and Meat. Eng., New York, Tech. Pub. 1760, 1944, 49 pp.

Jan 1, 1945

By Keith Harris

The U.S. economy grew moderately in the second quarter of 1985 with real gross national product (GNP) recording a seasonally adjusted annual growth rate of 2.0%, up from the 0.3% growth of the previous quarter but significantly below the 7.1% growth of the second quarter of 1984 (table I). Personal consumption expenditures grew 5.3%, with purchases of durable and nondurable goods rising 7.4% and 5.1 %, respectively; nonresidential and residential fixed investment--the two components of fixed investment--grew 11.8% and 5.6%, respectively; and Government spending rose 3.6%. However, these gains were tempered by a major decline in the growth of business inventories (from $19.1 billion to $8.3 billion) and the continuing growth of the net export deficit (from -$28.4 billion to -$33.3 billion). While the high value of the dollar compared with other currencies has been a major cause of the expanding trade deficit, its value, as measured by the monthly Federal Reserve Board (FRB) multilateral trade-weighted dollar index, has declined over 17 index points from its February peak to 140.94 in July. The July dollar value was still high historically. The rate of inflation, as measured by the fixed-weighted price index for GNP, remained low at 4.1%, down from 4.3% in the first quarter, and employment continued to grow at a rate sufficient to keep up with new additions to the labor force. Civilian unemployment has remained steady at 7.3% over the past 6 months. Industry Statistics The FRB recently revised its index of industrial production and changed the base year from 1967 to 1977,1/ The revised total index shows a 0.1 % higher annual growth rate between 1967 and 1984 than the previous index. In the slower growing or declining industries, such as metal mining, primary metals, and fabricated metals, however, downward revisions in the indices and rates of growth have occurred. The previous and revised annual rates of growth between 1977 and 1984 for several of the sectors of interest to the mining industry are shown in table 2.

Jan 1, 1985

Throughout October, U.S. producers priced unalloyed 99.5 percent aluminum ingot at 53¢ per pound. Dealers, in last month&apos;s domestic market, were quoting unalloyed ingot at a range of 45.5¢-46.3¢ per pound. Costa Rica recently issued a proposal to Japanese aluminum smelters to participate in an integrated aluminum-refining project which would include bauxite development. The project reportedly would include a 600,000-kilowatt hydroelectric power station, a 600,000-metric-ton-per-year alumina plant, and a 300,000-ton-per-year primary aluminum smelter. Two U.S. firms--Aluminum Co. of Amerjca (Alcoa) and Martin Marietta Co.--and several European aluminum smelters are also said to be interested in taking part in this project. Alcoa conducted a feasibility study for the Costa Rican Government in 1970 and estimated the bauxite reserves to contain 150 million metric tons.

Jan 1, 1977

In 1970, the U. S. Bureau of Mines contracted with Theodore Barry and Associates, a management consulting firm, to perform a one-year industrial engineering study of working-face hazards in underground bituminous coal mines. The field data was accumulated from industrial engineering observations in fifty underground mines. Supporting data for the analysis was derived primarily from the Bureau&apos;s fatal accident reports for the years 1966 through 1970. This report, Industrial Engineering Study of Hazards Associated with Underground Coal Mine Production, consists of three main parts: 1) The Fatal Accident Reports Analysis, 2) The Industrial Engineering Analysis, and 3) Multiflow Process Charts and Standard Time Data. The Fatal Accident Reports Analysis (Volume I, Section II) is based upon individual USBM fatal accident reports for 1966-1970. These were read, coded and computerized in terms of 84 significant variables. Cross-tabulations of these variables have been used to identify major underground hazards and to quantify significant causal factors. A very strong relationship was found to exist between fatal accident occurrences and low task experience. This led to a recommendation for formalized training, certification and supervision programs for miners. Victim compliance with federal regulations, mine regulations and supervisor instructions was analyzed, indicating that supervisors provide the most crucial communication link to workers. Thus, every attempt should be made to ensure the competence of immediate supervisors in the industry. Analysis of roof fall variables revealed a fatal propensity on the part of the miners to work under unsupported roof or under support conditions that are marginal. The technical approach to the problem is to make it physically impossible for a miner to work under these conditions; the behavioral approach is to ensure adequate training and develop proper safety attitudes among the miners. The Fatal Accident Reports Analysis revealed a need for normalizing data to interpret the results more accurately.

Jan 1, 1971

Electric power curtailments resulting from the coal strike, required Noranda Aluminum, Inc. to shut down its 140,000 ton-per-year (tpy) primary aluminum smelter at New Madrid, Mo., and layoff 308 workers. Other primary aluminum production facilities affected by the coal strike included the Aluminum Company of America plant at Evansville, Ind. which shut down half of one potline; the Eastalco Aluminum Co., smelter at Frederick, Md., which cut production by 7 percent; and the National-Southwire Aluminum Co. plant at Hawesville, Ky. which cut production by 6 percent. Alumax, Inc. announced that construction had started on a 91,000 tpy potline at the Eastalco primary aluminum smelter. The new potline will be owned 65 percent by Alumax and 35 percent by Mitsui & Co. Ltd. Howmet Aluminum Corp., which currently owns 50 percent of the existing 176,000 tpy facility, has the option of becoming a 50 percent owner of the third potline in 1982. Construction of the new line was scheduled to be completed in 1980.

Jan 1, 1978

The Black Hills Mineral Atlas briefly summarizes all important data available on the mines and mineral deposits in the Black Hills that have been explored, developed, mined, or located. The purpose of the atlas is threefold; First, from available data the general potentialities of the Black Hills region can be determined, although it is not possible to calculate actual ore reserves; second, it will provide the necessary basic information regarding a given property or commodity for further detailed study; and third, the compilation is a comprehensive directory of Black Hills deposits.

Jan 1, 1955

By David J. Hoadley

This report describes the development and limited testing of a semi-automatic, raise climber, Compact Service Hoist System designed for stope access in underground metal and nonmetal mines. Demonstrated capabilities of the system include a 1,000-lb payload capacity, control from the traveling cage and from up to three remote stations, operating in vertical or inclined raises 3 ft in diameter and up to 300 ft in length and a travel speed of 50 ft/min. The system has the capability of operating in crooked raises because the conveyance climbs two stationary wire ropes suspended down the raise. The drive unit is electrically powered with power and control signals supplied to the drive unit through an umbilical &apos;cable also suspended down the raise. The system has been designed for portability, ease of installation and minimum raise development. The hoist has been demonstrated successfully in an above ground test tower. This report provides a detailed description of the hoist design and its demonstrated performance to date.

Jan 1, 1985