Search Documents

By Kurt Oakes, John Williams

Placer Dome, US operates the Bald Mountain Mine. The Bald Mountain Mine is a surface operation located in remote northwestern White Pine County in east-central Nevada, approximately midway between Elko and Ely. The mine is in the Newark Valley along the southwestern flank of Bald Mountain a part of the Ruby Mountain range, at an approximate elevation of 7,500 ft (2,286 m). The geology at the Bald Mountain Mine is highly altered, both mineralogically, and structurally. Highwall stability and control have long been an issue at the operation, due largely to the varying geologic conditions. In some blasts as many as seven distinct geologic unconformities exist. These unconformities affect both final high wall integrities, as well as blast fragmentation characteristics. A 60 million ton (54.5 million tonnes) layback expansion of the existing “Top Pit” as well as development of a new satellite pit, “Sage Flats”, is being undertaken. Design final highwall pit slopes have been steepened from the traditional 47º to 55º in order to reduce overall ore-to-waste ratios, thereby improving economic viability for the expansion over the 4.5 year life of the project. With the increased usage of electronic detonators throughout the mining industry, mine operations staff, as well as representatives from the mines explosive supplier felt that an evaluation program incorporating electronic detonators would be warranted. The areas of focus for this evaluation would be resultant highwall pre-split integrities, peak particle velocity measurements (both near field and far field), frequency measurements, loader productivity, and visual interpretation of the results. The mine incorporates 25 ft (7.6 m) benches and uses separate trim blasts in conjunction with production blasts in order to reduce blast effects along final highwalls. Hole diameters in production blasts are 7? ” (200 mm). Typical production blast patterns are 18 ft x 18 ft (5.5 m x 5.5 m), drilled in a square pattern configuration. Shot sizes vary greatly, ranging from 200 holes to as many as 800. Bulk low percentage ANFO/emulsion blends are utilized as the redominant blasting agent. Non-electric dual delay detonators (25 ms/500 ms), with non-electric surface delays are the initiation system utilized in production blasts. Typical production blast design

Jan 1, 2004

By William McFerren, Pragasen Moodley

In contrast to global trends, African, especially South African, surface mining operations have shown a significant rate of adoption of Electronic Detonators (ED’s) over the last few years. Proven benefits of converting to ED’s from pyrotechnic initiation systems have aided this market conversion. These benefits are experienced throughout the mining operation. Benchmarking exercises, prior to the introduction of ED’s, form part of the conversion process and allow for quantifying improvements. Extensive work has been done on quantifying the benefits of converting to ED’s and have shown that results can be reproducible. Improvements have been experienced in many applications and include environmental impact control, improved mining efficiencies, increased cast benefit and improved size distribution. These step changes in blasting results, in conjunction with the adoption of ED technology have aided the rapid conversion of the African surface market.

Jan 1, 2004

By Paul Worsey, Attila Szucs, Mark F. C. Schmidt

The use of water stemming with small explosive charges has been successfully developed at the University of Missouri-Rolla. Further study has been started to explore additional applications and uses for water stemming. Work has been focused in the areas of rock excavation and perimeter blasting techniques. This ongoing work is being conducted internally as graduate and undergraduate level research. A paper describing the general technique for use with boulder fragmentation was published in last year’s proceedings. The excavation work took place in the form of both small bench and trench shots while pre-split and trim shots comprised the perimeter-blasting portion. The excavation work was located in both the Roubidoux sandstone formation and the Jefferson City dolomite formation. Hole diameters ranged in size from 1.5” to 3” diameter and powder factors ranged from l/l 0 to l/3 of the conventional charge weight. The water was used to both couple the explosive charge with the surrounding borehole, as well as stemming. No other stemming material or products were used. The method of using water stemming in perimeter blasting was found to work well. However, when used for excavation purposes, adequate rock movement was not obtained. The rock was often split, but not fragmented. The airblast was surprisingly low, but the ground vibrations were excessive. This is not the case with trim shots, and therefore this method appears ideal for splitting purposes, especially in areas where people do not like to stem the tops of the holes, and where airblast and vibrations are of concern. Water coupling dramatically increases splitting and fracturing. However, fragmentation is not only fracturing but also the movement and swelling of the material. As the charge weights are reduced with this method, sufficient gas volume is not created to cause this necessary movement and swell, which is critical in rock excavation. This explains why its successful application was limited to perimeter blasting applications.

Jan 1, 2000

By Geraldine Rosenthal, Gadi Yohan, Roman Benram

Description of Project: Tamar Group’s civil division was awarded a contract to implode the Sun Hotel, an abandoned 14-story building located along Bat Yam’s coastline, roughly two kilometers south of Tel Aviv, Israel. On Nov. 6, 2012, Tamar Group’s experts positioned explosives in strategic locations of the building, targeting its central pillars, which then caused the building to collapse within seconds. Tamar Group used a relatively small amount of explosives in order to generate a well-controlled blast. This is the largest scale demolition carried out in Israel to date.

Jan 1, 2014

By Unknown

Contact Local Law Enforcement Authorities. Contacting the local law enforcement authorities is essential to the quick recovery of explosives taken in a crime. Contact Local ATF Office. The local ATF office will work with the local law enforcement authorities investigating the theft. They can also assist in the preparation of the Theft/Loss Report for submission to the U.S. Bomb Data Center.

Jan 1, 2009

By Ronald Ticona

Generally, the drilling and blasting operation are managed independently to the processing plant outcomes. Therefore, the technical segmentation to determinate the ore drill and blast designs do not include processing plant rock properties such as Bond Work Index, Axb, Drop Weight Index or other. This work describes the case study of a copper mine in Peru, which, together with its strategic partner ORICA, have implemented projects focused on optimizing mine fragmentation. The year 2021, mine operation according to its mine plan would have a significantly increased SAG mill hardness, which would impact directly on copper concentrated production. An integrated strategy from mine to plant has become necessary to maintain the production levels.

Feb 6, 2023

By Alexander S. Escalante, Luis R. Ramirez, Nelson A. Arostegui

Research, analyze, discuss, design, and build an electric oven to perform one of the quality control tests the fanel or common fulminers to determine what temperatures they can detonate at. Give practical applications, conclusions, recommendations and bibliography.

Feb 1, 2020

The use of angled shot holes can be extremely effective in blasting faces that either have a great deal of toe burden or where it is difficult to give a drill access to a face due to backbreak and face erosion. However many quarry operators are wary of using angled holes because of the perceived possibility of increased flyrock and uncertainty of the driller's abilities to drill at the designed angle.

Jan 1, 1994

By Robert B. Hopler

The history of bulk loaded explosives begins with the loading of black powder and RRP (Railroad Powder) into vertical boreholes. The early air place, net of black powder and nitrostarch dynamites is covered, as are the brands and formulas of the nitroglycerinsensitized "Bagged" powders.

Jan 1, 1993

By Alastair Torrance, Gary Cavanough

Over the past two years a research project has been performed on reactive and hot ground. A key finding is that host materials including carbonates and coal are inhibitors to the reaction of sulphide and nitrates. The mechanism of this inhibition is pH buffering and isolating the surface of sulphide from reactants. It has been identified that acidity is a key driver of the reaction with a pH of 2 required for a reactivity event. A series of decomposition experiments confirmed that reactive and hot ground are essentially the same phenomenon with the heating produced either by the reaction of sulphide with nitrates or an external heat source. The results indicate that the key driver of detonation in reactive ground is energy and heat released from the acid induced reaction of sulphide and nitrate with no indications of sulphide being a catalyst or contributor to detonation apart from being a heat source. There must be sufficient sulphide and thermal insulation to provide and retain enough heat for detonation to occur. A pathway to detonation is postulated whereby the heat travels upwards and results in evaporation of water in the explosive. When the temperature reaches approximately 200°C (400°F) the ammonium nitrate starts to decompose, decreasing the mass of the reacting species. The material in the top layers has reduced density and specific heat hence the temperature of the top region rapidly increases up to >1000°C (1800°F) and may initiate detonation. Field tests on loaded blast holes support this proposed mechanism. Case studies are presented whereby the research findings are used to provide an analysis of historical reactive ground events.

Jan 21, 2025

By Steven V. Crum, Willard E. Pierce

Concern has been raised about the adequacy of current regulatory guidelines designed to protect homes from unwanted blast damage due to low frequency ground vibrations; in particular those with predominant frequencies below 6 Hz. This report summarizes and updates the preliminary results of a continuing Bureau of Mines investigation which will be completed later in 1995. Four structures at four different surface coal mines have been studied by examining their response to ground vibrations created from overburden blasting. House response to ground vibrations with dominant frequencies down to about 3 Hz were recorded. Many of the blasts produced ground vibrations with peak amplitudes above expected crack-producing thresholds. Response motions were compared to those predicted by theoretical single degree of-freedom response models.

Jan 1, 1995

By Gerald G. Schmitt, Richard D. Dick

Continuous Reflectometry for Radius vs Time Experiments (CORRTEX) was used to monitor several conditions of blasts such as the detonation velocity of the explosive column, the functioning of different types of initiators and initiation schemes, and the behavior of the stemming column confining the explosive. The CORRTEX data were also used to deduce the occurrence of dead pressing of ANFO slurry. Measurements of propagation speeds of shock waves in the stem column with various cables allowed some conclusions concerning bridging, stem failure, and stress levels in the stem.

Jan 1, 1985

By Syed M. Tariq, John W. Wilson, Paul N. Worsey

The position of a major joint in relation to a blasthole has a significant effect in presplitting. Broad research into the combined effects of firing two decoupled blastholes has been performed in the past. The effects of joints simulated between two blastholes has also been evaluated. However, no attempt has been made to investigate the splitting effects produced by firing a single decoupled blasthole. This paper presents the results of such an investigation.

Jan 1, 1996

By Natalie Zeleznik, Brian Hawkins, David Bradley, Rachel Gooding, Patrick Wilson, Brian Somes

"To perform a probabilistic risk assessment (PRA), a method of quantifying the risks associated withinfrequent, high consequence events, consequence models that generate representative estimates of human health consequences for a wide variety of representative scenarios are commonly used. Criteria that suitable models must possess include: (1) input requirements necessary to generate large volumes ofprobabilistic simulations; (2) the capability to output injuries with the necessary details and resolution;(3) the ability to capture the variety of different scenarios inherent in an assessment; (4) acceptablecomputational requirements; and (5) sufficient stakeholder buy-in for community acceptance."

Jan 1, 2017

By R. Alford

In the modern world of demolition safety is paramount and unnecessary or unquantifiable risks are not accepted (FasterCapital, 2024) and all risks must be kept As Low As Reasonably Practicable (ALARP) (BSI, 2017). This principle has led to a huge reduction in deaths in the last 50 years and the statistics continue to improve although this is starting to plateau (Beal, 2007). Under normal circumstances, this is now simply part of the normal way work is done and systems are in place to ensure both safety and economic profits are assured. What happens when the environment is less controlled and risks are unknown, such as after a natural disaster, war, an accident or a stand-up from a failed demolition attempt? A dangerous structure cannot responsibly be left alone with a fence around it so some action must be taken, but how can this be done safely and responsibly? An incident in Didcot, England in which half of a power station’s boiler house being prepared for an explosive demolition collapsed suddenly, killing four men in 2016 provides a useful case study of how technology, creativity and planning can be used to conduct complex demolition fully remotely to avoid any further risk to life.

Jan 21, 2025

By Brian Hawkins, David Bradley, Rachel Gooding, Lucas Rodriguez, Patrick Wilson, Kevin Wegman, Dhruv Mittal

The Department of Homeland Security (DHS) has undertaken a probabilistic risk assessment (PRA) approach to quantifying the infrequent, yet high-impact explosive terrorist attacks on the United States (US) homeland and aiding in mitigating that risk through efforts ranging from intelligence gathering, defense postures, detection architectures, partnering with industry to prevent acquisition, and informed medical response. Based on an evaluation of existing model options, a path to the realization of an exterior explosive model (EEM) that builds upon existing models while meeting runtime requirements, maintains consistency with existing DHS chemical, biological, radiological, and nuclear (CBRN) consequence models, and provides sound estimates of the human health consequences of explosive terrorism attacks in open-air urban and rural environments.

Jan 1, 2018

By Tom Snyder, John Brulia

Part 4 is the final article by the authors on hazardous materials (HM)transportation safety and compliance for U.S. shippers and carriers who offer and transport commercial explosives in commerce on public highways. This article covers hazardous materials (HM) cargo segregation and securement of non-bulk packaged explosives.

Jan 1, 2015

By Robert B. Hopler

Explosives have been important to the oil and gas industries since the very earliest days. The first wells of Pennsylvania and New York in the 1860’s were able to be brought back to productivity by the use of nitroglycerin after their porosity was lowered by the high para& content of their oil. Success in the use of seismic waves to locate enemy artillery in the First World War led to the use of explosives in the 1920’s for generating ground vibrations to locate geological structures favorable for the entrapment of oil. Explosives also find widespread use in the more conventional applications of well site preparation and pipeline construction. Explosives applications unique to the oil and gas industries include the jet perforating of casings and formations, fighting well fires, and cutting casing during well shut-in.

Jan 1, 1998

By Tyler Rockley, Carla Reyes

Autonomous fragmentation measurement systems designed for shovels have been in operation for nearly two decades, however fragmentation systems capable of performing in the dynamic conditions of the front-end loaders (FEL) were only recently introduced to the market. This paper presents an in-depth evaluation of an automated digital fragmentation measurement system specifically designed to perform under the dynamic operational conditions of the FEL in two of Teck’s mine sites. As early adopters of this novel application, Teck embarked on a Proof-of-Concept (PoC) trial phase, defining a set of key performance indicators (KPIs) to qualify the performance of the digital solution in tough mining operating environments. The KPIs focused primarily on the hardware robustness, quality of image and segmentation, both day and night, availability of the system and sample ratio. The benefits expected from using this technology include increasing the safety of the current fragmentation measurement process, improving the quality of the analysis, increasing the sample representativeness, and using the attributes of the system to create an oversize detection alert to inform the loading operation process. A critical part of the evaluation was verifying the system’s effectiveness on the particle segmentation algorithm as this element often gets overlooked, especially when dealing with the large number of samples autonomous systems can generate; minor misclassifications due to inadequate segmentation are often dismissed as they might not be statistically significant, however systematic misclassifications can cause unacceptable deviation in the data and limit the intended application of the technology. The system’s performance was further validated through several tests that involved identifying objects of known sizes to ensure the reliability on the consistency of the particles’ segmentation.

Jan 21, 2025

By Karl Kure, Anders M. Heltzen

Mixtures of prilled ANFO and 0,5 - 3 mm polystyrene balls are interesting substitutes to the tube charges or other types of reduced explosives or detonation fuses. Experiments have shown detonation ability even of a mixture of 95% bolt polystyrene balls and 5% ANFO. The gas and shock energy in the mixtures decrease proportional with the content of polystyrene. The detonation velocity shows higher values than expected for mixtures with more than 50% (vol.) ANFO.

Jan 1, 1980