Search Documents

By Dyno Nobel

Impact of Enhanced Security on Operations Budgeting - What is the “value” I receive for enhanced security? Is there a “return” for the money I spend? Regulatory driven Economic driven

Jan 1, 2006

By Lon Santis

In 1923, Ralph Assheton compiled a report for the Institute of Makers of Explosives (IME) on accidental explosions in manufacturing plants. The report chronicles the type and amount of explosive involved in the event and the effects and distances to nearby buildings and workers for over 100 events from 1880 to 1916. Apparently, this report was never published but served as the origin of the IME’s first intra-plant distance table published in Pamphlet No. 3 in 1926. The effort was a parallel effort to the IME’s development of the American Table of Distances. The intra-plant distance table has never been changed by the IME and follows the US Department of Defense (DoD) standard very closely. This paper freshly compiles the data from the 1923 report and analyzes it with modern methods not generally available in 1923. Interestingly, the analysis indicates that the original intra-plant distance tables were established primarily to protect workers from serious injury and that preventing propagation was a side benefit. The data shows that a strong relationship exists between the probability of injury and the traditional K-factor. The data indicate that people in the open are better protected than those inside structures and that barricades reduce risk close to an event. Individuals at the intra-plant distance had a 95 percent chance of receiving no worse than a minor injury. A comparison of the data to explosive event consequence models indicate the models are overly conservative in regards to risk inside inhabited building distances.

Jan 1, 2010

By Shadrack Nuamah, Erik Westman, Bright Afum, Jesse Addy

Rock fragmentation is the most critical aspect of hard rock production blasting due to its significant impact on drilling and blasting costs and the economics of subsequent loading, hauling, and crushing operations. This study analyzes current cost trends in the drill and blast operations of an anonymous open pit gold mine and proposes cost-effective drill and blast geometric parameters. The investigation focused on one operational pit with provided design parameters for two shots, shot 1 and shot 2. Existing blast parameters and two additional proposed sets of geometric parameters were evaluated using the Kuz-Ram and Chung and Katsabanis fragmentation models to estimate mean fragment sizes. The results indicated that the proposed blast parameters produced estimated mean fragment sizes within the mine’s desired range (not exceeding 45 cm). Additionally, the explosive energy was utilized efficiently per in-situ material blasted. The proposed parameters increased the estimated total volume of in-situ material fragmented by approximately 14% for both Shot 1 and Shot 2 compared to the current parameters. Furthermore, adopting the proposed blast parameters could lead to significant cost savings. The evaluated total drill and blast cost savings were approximately 11% for Shot 1 and 12% for Shot 2. These savings stem from the increased efficiency and effectiveness of the blast operations, highlighting the potential for substantial economic benefits. This study demonstrates that optimizing blast geometric parameters will allow open-pit mines to achieve desired fragmentation, utilize explosive energy more effectively, and realize considerable cost savings in drill and blast operations.

Jan 21, 2025

By Drew Martin

In March 2010 the Boral Linwood Quarry, Adelaide South Australia, implemented the blasting contractors Monte Carlo Blast Vibration Model as part of their blast design process. The Linwood Quarry was developing an area where blasting activities were marginally complying with the statutory vibration limits. Compliance to the statutory limits was only being achieved through the use of small blasts (less than 15 000 T (14 763 ton)) at a high cost to the quarry.

Jan 1, 2012

By Miguel Humpire Huamani, Gustavo Huerta Valer, Jorge C. Cárdenas Miranda

As part of the continuous improvement and increase productivity to achieve the mining and extraction plan of a low-grade open pit copper operation, alternatives are required to expand the blast pattern to maximize drills and steels resources along to ensure the fragmentation results for the process plant with volumes from 500k tons of broken material per day. Therefore, the application of aluminum based ultra-high energy explosives was an alternative to achieve the objective of expanding the production pattern by 34% while maintaining energy factors levels along with the distribution of explosive and the application of the pocket charge in the stemming level, reducing the load factor, maintaining the fragmentation results in P80 and increasing the percentage of fines less than 1.0 in (2.54 cm). An important development to ensure the supply and perform successfully blasthole loading was the implementation of a supply system with pre-blending (aluminized emulsion) which is stored in silos and load through factory trucks. In the field we ensured optimal initial and final density levels with chemical sensitizer to perform the most fracturing work in the rock, complementary evaluations were performed to predict flyrock and define safe equipment evacuation radiuses along with advanced vibration monitoring for the sustainability of the mine.

Feb 6, 2023

By Dale Preece, Steven Case, Cassidy McAllister

Simplot Phosphates produces high quality phosphate fertilizer through open pit mining. The operation near Vernal, UT began as a three-pass mining process carried out with drill and blast followed by the combined effort of shovel-truck and dozer material removal. The first two passes removed the overburden and the final pass mined the relatively hard phosphate ore for processing at the mill. Vertical blastholes were employed in all of the mining passes.

Jan 1, 2012

By Ian Bell

This paper investigates fragmentation in an aggregate quarry using the fragmentation-energy fan concept. Six blasts were monitored, located one behind the other in the same quarry area. The rock structure was blocky, the water level and the usage of explosives were variable within and between the blasts. The powder factor above grade was between 0.28 and 0.44 kg/m3 (0.47 and 0.74 lb/yd3). Fragmentation of the plant feed was measured using an online digital image analysis system and three belt scales. The oversize material that was not directly fed to the plant after the blast corresponds to 3‒9.3 % of the total. Data from image analysis was used to build the size distribution in the coarse range (fragments above 120 mm), and the passing fractions at 120 and 25 mm (4.72 and 0.98 in) obtained from belt scales data were used in the range 120‒25 mm (4.72 ‒ 0.98 in) . The non-dimensional percentile sizes between 10 and 90 % for each blast are described through power functions of the powder factor above grade; the model coefficients are statistically significant. From them, using the principles of the fragmentation-energy fan and the Swebrec distribution properties, the fragmentation can be expressed in terms of the powder factor by means of five parameters: the fan focus coordinates and the three parameters of a function of the exponents vs. the percentage passing. The model shows a good capability to describe fragmentation.

Jan 1, 2019

By Harry Verakis, Thomas Lobb

Blasting accident data over a 30-year period (1980-2010) are summarized and presented for all types of surface and underground mining operations in the USA. The historical record of injuries from blasting accidents in all types of mines continues to show a significant decline. The overall decline in mine blasting injuries in the U.S.A. has resulted from advancements in blasting technology, training and improvements in blasting products and blasting processes. Some of the technology advancements such as safer blasting agents and computerized bulk vehicle loading, electronic detonators and remote operated blasting systems, and computerized blast design have and continue to significantly contribute to improvements in the historical blasting safety record. Also, the progress of significantly improving the safety of mine blasting has resulted from the combined efforts of miners, mine companies and operators, miners, unions, explosive and blasting product manufacturers, associations such as the International Society of Explosives Engineers and the Institute of Makers of Explosives and various government agencies.

Jan 1, 2012

By N. Skopak, W. Birch, A. Douglas, C. Johnson

Determining the origins of air overpressure has been a long-debated topic within the explosives engineering community. Historically, it has been accepted that the initial face movement gave rise to air displacement, resulting in an air overpressure pulse. Later research proposed that the air overpressure pulse resulted from the shockwave rapidly propagating through and impacting the quarry face. Most recently, researchers have derived that air overpressure is associated with the gas phase from which a gaseous product from explosives rapidly pours out the quarry face under high pressure. Significant research has strongly indicated that the time at which the air overpressure pulse exits the face fails to coincide with either the arrival of the shockwave at the free face or the initial face movement. Research has consistently shown that the shockwave arrival at the face occurs before the air overpressure pulse leaves the face. Therefore, to best determine which blast mechanism contributed to the initial air overpressure pulse, testing was aimed at verifying the precise time at which the air overpressure exited the faces compared to when the face first moved. This research describes tests using scaled concrete blocks, which provided the ability to control the key parameters necessary for the research to be successfully concluded. Black powder was selected as the energetic material to eliminate the production of the detonation wave while still inducing other gas-producing effects. The components evaluated were air blast arrival times in front of the face, the initial movement of the blast face, the precise initiation time of the blast hole, timing of pressurization within the rock mass (between borehole and face, or adjacent borehole), and the speed of sound in the air. A detailed timeline was created which portrays the actions within the blast to promote an understanding of the sequencing of events. The results showed that the initial face movement occurred at 17.57 milliseconds (ms) while the calculated time at which the air overpressure exited the face occurred at 7.07 ms. The large disparity continues to reaffirm the premise that the origin fails to coincide with the air pressure pulse. Average pressurization through the block occurred at a rate of 341.23 feet per second (104.15 meters per second) which resulted in the gas release pulse being calculated to exit the face between 4.41 and 6.21 ms. This pulse correlates more accurately with the air overpressure origin timing which will be the focus of continued research. Knowing the precise origin of blast-induced air overpressure will assist in being able to better control it through appropriate blast design.

Jan 1, 2024

By Damien Bretall, William Fourney

Due to the changing face of warfare there is an ever growing need to protect the underside of combat vehicles from mine blasts. This paper presents a new method to better characterize the pressure profiles experienced by a plate as the blast develops. The explosive deformation of a small-scale plate was recorded using synchronized high-speed digital cameras, and then analyzed using 3D Digital Image Correlation software. Time-varying pressure profiles were input into an axisymmetric FEM simulation by fitting curves to data obtained from tests using Kolsky bars to measure pressures. These were then modified to find possible profiles that produce the measured deformations. It was discovered that the final deformation cannot be determined from only total impulse or peak pressures, and that it is very sensitive to the time and spatial decay of the pressures.

Jan 1, 2009

By Tyler Rockley, J. P. Remi Proulx, Ruilin Yang

A highwall blast vibration project was carried out to quantify the level of blast vibrations produced from a trim blast in soft rock and a combined production and trim blast in hard rock. Combining production and trim blasts could be performed without exceeding the mine’s vibration limits.

Feb 1, 2020

By Lizbeth A. Escobar, Phol M. Llanos, Maritza Y. Avila

The present research develops the estimation of critical parameters such as the distances and times between holes to avoid failure due to dynamic pressure in electronic detonators based on the near-field ground vibration model of Holmberg & Persson and the hydrodynamic model of Neyman.

Feb 1, 2020

By Chick Kerkering, Stephen Iverson

Perimeter control blasting is common in civil construction projects but not as common in mining. A poorly designed and executed underground mine development blast design can result in unwanted wall rock damage. This damage increases the risk of rock falls and injury. With the availability of good drilling equipment, it is a simple matter to add the few extra holes needed to change conventional drifting into drifting with perimeter control.

Jan 1, 2008

By Frederick B. Kuhnow

Harmonic energetic delamination of T2 building is being considered for demolition at a formerly known atomic lab. The T2 building is within a containment structure that is under a negative pressure of -49 Pa (-0.2 inches of WC) so that no remaining radioactive material is leaked out. The T2 containment enclosure is a portal frame-type system that spans east/west over 35.05 m (114’-11 7/8”) and spaced 2.9 m (9’-6”) apart. The west side of the portal frames is supported by a 64 cm (2’-1”)thick concrete wall which is backfilled to the west and open to the T2 basement to the east. The east side of the portal frames is supported by a 61 cm (2’-0”) thick concrete wall that is backfilled to the east and open to the tank farm vaults to the west. A concrete slab-type footing supports both the east and west walls. Transverse walls provide lateral support for the walls as part of the original design. The west wall has an elevated slab that provides further stiffening of the concrete wall between the transverse walls.

Jan 1, 2017

By Sandra Penttinen

There are several ways to get a positive reaction from abutters to blasting projects. When you need to enter structures to conduct a blast-blast inspection, the impression you make on the structure owner must be positive from the very start. Your public relations with neighbors is the key. The purpose of all communications with persons residing near planned blasting operations is to educate structure owners as to what will take place during the blasting operations, to explain that safe blasting practices will be followed and vibration and airblast limits will be imposed to protect surrounding structures from damage. Once access into structure is obtained, the structure owner can be shown, by careful documentation, all existing cracks and defects in the structure prior to blasting and construction. The objective of your visit and all communications is get your foot into the door and win the confidence of the structure owner so that he or she understands blasting will not compromise the structure.

Jan 1, 2005

By S. Hosein, W. Birch, C. Johnson

The widespread adoption of electronic detonators has given rise to the development of linear superposition to control the environmental impact on both third-party properties and residents resulting from blast induced vibrations. Linear superposition has become a very effective tool in the hands of blasting engineers and has enabled aggregate reserves to be accessed that once had to be abandoned. This in turn has resulted in more and more complex blasting pattern to be developed that contain multiple rows and multiple decks all with different maximum instantaneous charge weights of explosives. This is then made more complex by having to consider multiple sensitive locations often with different Peak Particle Velocity vibration limits. This paper is a case study of what did happen when a blast was designed that “pushed the boundaries” of environmental blast vibration design and control, without taking fully into account the fundamental geophysical properties of seismic waves. The resulting blast design caused a greatly enhanced s-wave to be created in a critical direction from the blast pattern. The root cause being the s-waves from earlier detonating decks in the blast pattern arriving within 2 milliseconds of decks detonating later in the blast pattern. 209 individual decks were fired in the blast pattern of which 41 pairs of decks arrived at the observation location less than 2 milliseconds apart when taking into account the s-wave speed and direction. The lesson to be learned when using electronic detonators to limit ground vibrations from complex blasting patterns, is that it is just not good enough to look at the planned firing times, a professional blasting engineer must also understand the likely interaction of the various seismic wave types created and their combined impact on any given monitoring location.

Jan 1, 2024

By G. C. Naveen

Punatsangchu Hydroelectric Project Authority is constructing 1020 MW underground hydroelectric project in Bhutan. The project envisages construction of concrete dam, Desilting Chamber, Head Race Tunnel, Power House Complex and Tail Race Tunnel. Tunneling is one of the major activity in any underground projects as they are driven for multiple activities. By and large the tunnels are a major part of connecting networks from surface to caverns/underground working sites. Many tunnels in hydropower project are part of water conducting systems and one such important tunnel is the Tail Race Tunnel in this project and had to be excavated in thinly foliated rockmass conditions by D&B method. The rockmass is traversed by three to four joint sets and few minor shear seams. Rock Class “Q” values were between III and IV. Tunnel was excavated by full face parallel hole drilling blasting method. The adopted blasting method consisted of drilling 45mm (1.77 inch) diameter holes to a depth of 2m and the drilled holes were charged with 40mm (1.57 inch) diameter cartridge explosives and charges were initiated with half second non electric initiators. The perimeter holes were drilled at closer spacing of 30cm (1 feet) and alternate holes were charged using 32mm (1.23 inch) diameter cartridges explosive. Low dipping foliation joints present in the rockmass tend to slab in crown portion and erratic occurrence of intrusive bodies lead to unpredictable behavior of rock mass posing a major challenge for the safe excavation. Stability was a major issue through controlled blasting under constant supervision too could not limit the overbreak in certain weak rockmass conditions thereby exposing cavities of about 2.5m (8.2 feet). The stabilization of these cavities and handling the overbreak due to rockmass condition was time consuming and warranted additional supports. With systematic measurements and controlled blast designs the Horse Shoe Shaped Tail Race Tunnel of 9.1 m (29.85 feet) diameter and 304m (997.37 feet) length to connect with Downstream Surge Gallery of 314m (1030 feet) length, 18m (59 feet) wide and 58.8m (193 feet) height in thinly foliated and jointed biotite gneiss rockmass was successfully excavated.

By Norm Disley, Kingsley Hortin, Gertjan Bekkers

As part of the expansion of the Kidd Creek Mine to 2,682 meters (8800 feet) below surface, two largediameter 3000kW (4000HP) booster fans were installed at the 6000 level. Shortly after commissioning the fans, significant damage to the fan bearings were observed, forcing several shutdowns for repairs, which were very disruptive to the mine’s production process.

Jan 1, 2008

By Peter Dare-Bryan, Will Hunt, Lee Julian

It is well-known that blasting has an economic effect on grade control activities. However, until recently, methods did not exist for measuring the grade control value change caused by the blast. Rules of thumb were the best method to minimize ore loss and dilution, as simulation has been traditionally constrained by time and computer power. Even with these rules followed, an extensive study performed on over 150 blasts showed that the value change caused by the blasts followed a normal distribution – some blasts created value, and some blasts destroyed value. The question naturally asked was “How can we ensure the blast designs are optimized to create value?” Recent advancements in computer power have enabled real-time blasting simulations that create post-blast grade control models before the blast is fired. Understanding what will happen before it happens allows blasters and grade control personnel to iterate designs, searching for the highest value achievable.

Feb 6, 2023

By J Silva Castro, W C. Wedding, B T. Lusk, J Calnan, E G. Morris

The emergence of electronic detonators for use in production mine blasting has enabled mining professionals to rethink the traditional blast design methodologies that pertain to timing. In many ways, electronic detonators can allow great advances in productivity, cost effectiveness, fragmentation, and safety. This paper reports on an independent study quantifying the accuracy of two electronic and two non-electric systems in which 674 detonators were tested. This research aimed to determine the accuracy of commercially available electronic detonators as compared to non-electric shocktube systems. Each system was tested over the viable ranges of delays available. Statistical models were then applied to quantify the scatter present in each system. Suggestions for the use of electronic detonators are made from the findings of this work. This work was made possible through funding from the United States Department of the Interior Office of Surface Mining Reclamation and Enforcement.

Jan 1, 2012