Search Documents

By Matti Kongas, Kari Saloheimo, Antti Remes

"The paper studies the control performance of the flotation process as a function of the measurement accuracy and sampling frequency of an on-stream XRF analyzer, using a simple dynamic model. An additional aim is to assess how the economical result of a mineral flotation process depends on the quality of process control based on the on-line elemental assays.An on-stream XRF analyzer measures the concentrations of slurry lines in a continuous cycle from several process points. The control performance depends on the analytical accuracy and sampling frequency of the concentration measurement. With a long cycle time, the state of the process changes before a new measurement becomes available. With short measurement times the statistical variance of the counted Xray pulses increases, increasing the random error in the analysis. In addition, the measurement accuracy depends on the concentration of the component to be measured from the slurry.To quantify the effect of analysis error and frequency to process control, a simple dynamic process model is created in the Matlab environment. Data from a copper flotation circuit is used as a test case. The process model comprises a first order reaction equation and the grade-recovery -relationship estimated from process data. The control was modeled using the control strategies implemented into a rule based advanced control system. The economical performance of the control was studied by calculating the overall net smelter return at various analyzer parameter combinations."

Jan 1, 2003

By Patrick A. Turner, Timothy J. Olson, Abraham J. Schutte, Roman van Ommen

"The use of classifying devices in grinding circuits dates back to the early 1900’s when classifiers were installed to close ball mills. The search for ways to further improve grinding circuits led to the use of hydrocyclones in place of mechanical classifiers in South Africa in the early 1950’s. Today Hydrocyclones are considered as the best classifying devices to close grinding circuits. After 50 years of development the hydrocyclone has changed significantly when compared to the designs of the early days, but the focus to circuit optimization must be expanded to an understanding of the integral system consisting of mill, cyclone feed pump and cyclone.The key to good cyclone circuit design and operation in primary grinding circuits will be discussed including individual cyclone design features such as cone angle or materials of construction, as well as orientation and manifold configuration.Cyclone performance issues as well as maintenance considerations will be detailed in an effort to achieve consistent cyclone operation with minimal coarse solids in the overflow. “The importance of constant cyclone feed conditions is unquestioned today. The challenge of Cyclone sizing is a large number of not fully known variables prior to startup. The most significant unknown variable is slurry viscosity. Because of this, engineers often specify a conservative cyclone system that produces a finer than required separation. However, this approach often leads to higher circulating loads and a higher overflow density in order to produce the required separation. The higher cyclone overflow density results in a less efficient cyclone separation. The average concentrator can pick up 2-4% finer overall grind by having a more aggressive cyclone operation.”"

Jan 1, 2003

By Takashi Furuyama, Sukeyuki Mori, Abel Bissombolo

"In flotation practice, a good recovery of minerals largely depends on the degree to which the valuable minerals have been liberated from the associated gangue during the grinding process. Therefore, a regular measurement of the degree of liberation can provide data for the assessment of the quality of separation and predicts the effect of changes in the grinding-classifying circuit on flotation process. Generally, the standard procedure for measuring the degree of liberation requires the preparation of polished sections - a time consuming operation that also has the disadvantage of providing an overestimated number of free particles because of the stereological nature of produced samples.The present work is an alternative approach to avoid these miscalculations and establish a system of control for fluorite flotation plants. The system deals no only with the state of liberation but also the dynamic behavior of individuals particles and mineral components within the grinding-classifying and flotation circuits. It involves methods such as sieving, x-ray diffraction analysis, study of polished sections and microscopic counting of preliminarily sieved minerals particles from a fluorite processing plant, randomly dispersed on a glass slide, but not embedded in a resin mounting medium. If a complete information on the textural properties of minerals in the ore (including its mineral components distribution) can be obtained through x-ray diffraction analysis and study of polished sections, the microscopic counting is used to determinate with enough accuracy the mineral liberation, estimate the grade of fluorite ore and products, determinate the deportment and approximate recovery of individuals particles and mineral components within the investigated circuit. For a count of 100-1000 particles in each n-size range, the counting method was found to be a particularly reliable and less time consuming operation that could substitute the chemical analysis of fluorite ore for an estimate of the grade:"

Jan 1, 2003

By E. Barsky

"The aim of separation is to obtain two products that are as distinct as possible from each other. It is currently believed that the most objective criteria for the quality of a separation are the Hancock criterion and the entropy criterion.1. Hancock criterion:- for yield of fine product"

Jan 1, 2003

By Scott C. Brown, Ivan U. Vakarelski

The particles commonly encountered in mineral benefication schemes have irregularites that are expressed at many different length scales. In part, this originates from preceding processes (e.g. makedown, comminution, handling and storage), which are known to chemically and physically modify the bulk particle and its surface. Interparticle tribology, dissolution and reprecipitation events along with large-scale mechanical stresses are just a handful of the interactions encountered during processing of particles prior to separation. It is feasible to imagine that each one of these events may impose a fingerprint of characteristic nanoscale, microscale, and macroscale morphological changes that can modify the overall interaction of these particles within a system. Suprisingly there are just a few works on how these resulting features can alter the performance of benefication schemes, and especially flotation.

Jan 1, 2003

By Xie Jiyuan, Hu Yuehua, Yang Songrong, Zhu Zhansheng, Qiu Guanzhou

"By the end of 2000, the first bio-oxidation plant in China that designed by ENFI come successfully into commercial operation in Yantai Gold Smeltery. Its capacity is 50t/d of refractory gold ore concentrate. After the extension, the capacity of bio-oxidation plant reached 80t/d of refractory gold ore concentrate at end of 2001.The refractory gold ore concentrate treated is from different gold mines. After proportionate feeding, the feed typically consists of Au (52.7g/t), S (24.42%), As (3.58%).The bacterial culture used in the bio-oxidation circuit is taken from a mine in south of China, and has been grown over 20 years on a variety of sulfide concentrates in a laboratory of mineral processing, and has shown to be adaptive to growth in a high concentrations of arsenic. It is a mixture of mesophilic microorganisms. The nutrients used in the bio-oxidation process are (NH4)2SO4, KH2PO4, KOH.Before feeding to bio-oxidation circuit, the concentrate would be milled to minus 43µm. The biooxidation product is fed to solid/liquid separation system that consists of a thickener and two press filters, solid from the system is fed to CCD circuit, liquid from the system is fed to neutralization area. The neutralized product is fed to another solid/liquid separation system, and the solid from the system is disposed of on a wasted quarry pit, the liquid from the system is returned to bio-oxidation circuit for reusing."

Jan 1, 2003

By Rhulani F. Maluleke, Francis W. Petersen, John H. Marsh, Johann de T. Steyl, Allan Nesbitt

"Pressure leaching of chalcopyrite and nickeliferrous pyrrotite at temperatures between 105 and 200 ºC has been proposed as a potentially viable route for the extraction of mineral elements from sulphide concentrates. In general, these concentrates contain iron, and the economic success of the processes is partially dependent on the choice of the environmentally acceptable iron-removal technique. One of the most widely used methods for the removal of iron from sulphate liquors is precipitation as hematite, goethite, or jarosite. The nature of the iron precipitate formed, dictates downstream dewatering and residue treatment and disposal options. However, a better understanding of iron precipitation under the defined process conditions would consequently be of benefit in process design and optimization.This study investigated the precipitation of iron in the autoclave at temperatures between 105 and 200 ºC. The effects of temperature, acid concentration, iron concentration, and the presence of other metal cations on the nature and composition of the precipitates were determined."

Jan 1, 2003

By Jurgens J. Louw, Vincent C. Smith, Gareth C. Smith, Agit Singh, Dave G. Hulbert

"During 2000 Mintek Developed the PlantStar plant wide control platform for the minerals processing industry. The flexibility of the PlantStar control platform has enabled Mintek to investigate and easily develop new control strategies for both milling and flotation. This includes a Solids Feed Controller, a Safety Limit Controller, Mill Power Optimiser and Flotation Optimiser, amongst others.Processes with long dead times, like a feed belt to a mill, are difficult to control. The solids feed controller was developed for minerals processing plants using a specialised time delay compensator. Using conventional time delay compensators that are purely model based, results in robustness problems due to model uncertainties. The Mintek Solid Feeds Controller makes use of a plant model, but compensates for model inaccuracies, giving more controller stability and a more robust delay compensation algorithm.Often there are more variables on a plant that need to be controlled (process variables) than there are variables to control them with (manipulated variables). Process constraints are often reached and violated. Safety control loops are necessary to prevent constraints being reached. The safety limit controller has been developed to switch smoothly between normal and safety control loops without bumping the process. The safety loop output is chosen in accordance with a predefined list of priorities and whether the respective constraint boundaries are exceeded.The Mill Power Optimiser helps to find the power peak on the mill power curve. It continuously perturb the solids feed rate to learn ‘where’ on the curve the mill ‘was’ and then to drive it continuously toward the middle, maximum power drawn. This insures maximum grind with maximum throughput. It also prevents power dips due to mill overloads by cutting the solids feed to a minimum if the power drop below a specified threshold. Once the power rises above the threshold the solids feed is increased again to an intermediate value from where it start the perturbations again to find the maximum. This makes the milling circuit easier to operate."

Jan 1, 2003

By Pradip, Beena Rai

A molecular modeling study was carried out on an adsorbed oleate monolayer on the surfaces of three calcium minerals, fluorite, calcite and fluorapatite using Universal Force Field (UFF) potentials. The cleavage plane of calcite {104} was the best template for oleate monolayer adsorbed since the surface structure enabled all the calcium sites available on the surface to be occupied by oleate anions. The area occupied per chain of oleate in this well packed monolayer was computed to be 20.2 Å, which exactly matches the value calculated to be the parking area per oleate molecule for a fully packed monolayer based on strictly geometric calculations. On the other hand, the precentage of calcium sites occupied by oleate to achieve a fully packed monolayer in case of fluroite and and fluorapatite was found to be 67% and 75% respectively. The results of this theoretical study suggest that while all the three adsorption conformations, that is unidentate, bidentate and bridging type are equally likely on fluorite and fluorapatite, bridging is most likely on calcite. Interestingly, all the conformations are observed experimentally for calcite-oleate system also. The reasons for this discrepancy between the theoretical predictions and experimental observations are not clear. More work is required to resolve this discrepancy, in particular simulation studies in presence of solvent water molecules on the surface.

Jan 1, 2003

By Choi Sang-Ken, Chung Hun-Saeng, Kim Byoung-Gon, Lee Jae-Jang, Park Chong-Lyuck

"Graphite has unique properties such as high thermal resistance, low thermal expansion coefficient, and good thermal and electrical conductivity, and is often utilized as coating materials for electrical conductors, TV Brown tubes, electromagnetic shields, and so on. Additionally, its excellent lubrication property is widely used in oil and solid lubricants. Finely ground graphite particles in the sub-micron range are commonly used for these applications.Sub-micron fine graphite particles are typically prepared in liquids by vibration ball mills. However, it is known that the wet process takes long periods of grinding time like 24 hours or more and requires a series of subsequent highenergy operations such as de-watering, drying, regrinding and classification. On the other hand, there would be numerous advantages if fine grinding could be done effectively in dry atmosphere. However, since crystalline graphite has a layered structure giving a high lubrication property, its dry grinding, especially when obtaining sub-micron size particles, is extremely difficult. The shape of the graphite particles is also important for its utilization since particles with flaky shape can maintain relatively high electrical and thermal conductance as well as lubrication ability. Therefore, it would be necessary to reduce the size of graphite particles into fines with flaky shape while grinding proceeds. Dry grinding characteristics of natural graphite under various atmospheric conditions with gases using different mills were studied, and fine flaky particles by grinding the graphite intercalation compounds and the exfoliated graphite were produced. However, there were no sufficient investigations on the size reduction of natural graphite at low atmospheric pressures in attritional milling conditions. The main purpose of this paper is to provide sub-micron fine grinding characteristics of natural crystalline graphite at various degrees of low atmospheric pressure, and to discuss the size reducing models in an attrition mill"

Jan 1, 2003

By John C. Gathje, Rick Moritz, Wilhelm de Beer, Gary L. Simmons

"Froth flotation has a long history of success for the recovery and concentration of a wide variety of minerals of commercial interest. Both the art and science of flotation have progressed greatly, and as our knowledge has increased so has our ability to improve mineral separations and recoveries.One area of interest in recent years has been the flotation of refractory gold ores to recover the goldbearing sulfides. In many instances, the use of conventional air flotation to concentrate these values has achieved only limited success. However, as a result of intensive research, Newmont Mining has expanded the boundaries of flotation, and it can now be used to successfully treat many gold-bearing sulfide ores as well as platinum and palladium ores. This has been achieved through the use of the patented N2TEC technology, which utilizes nitrogen as an inert gas in the flotation process."

Jan 1, 2003

By Zhou Junwu, Sun Chuanyao, Wang Fuli

"In this present paper, the authors introduce the artificial neural networks into the modeling of the industrial flotation process, integrating information technology, control theory and intelligent optimizing method to flotation technology. The new idea gives a new way to solve the difficulty in this field, and therefore brings the study on the automatic control of flotation process in China into a new start.The Radial Basis Function (RBF) network, featuring a quick learning speed, is one of the feedforward neural networks. It has attracted much attention from automatic control recently for its implementing the nonlinearity mapping through adjusting the parameters of the nonlinearity transfer function. One of the online adaptive learning algorithm—the nearest neighbor-clustering algorithm, which can automatically determine the number of hidden units, has been implemented in the MATLAB programming language in this paper, laying the foundation for the flotation models.The relation model between ore pulp characteristics and reagents consumption has been proposed using the RBF networks based on the industrial lead rougher flotation of lead & zinc ore, and the simulation has been conducted in the laboratory with the results matching the samples data very well. The Xilin Lead & Zinc Mine Flotation Process Intelligent Consultation System of Reagents Consumption, which suitable for industrial process, has been developed. The reagents consumption advised by this system would stabilize the flotation process, and increase the recoveries. It could be used for providing the technological consultation to flotation operators in site, and for training new operators."

Jan 1, 2003

By Atsushi Shibayama, Toyohisa Fujita, Luo Lin, Toshio Miyazaki

A novel process is developed in this study for separation of tungsten and vanadium from a leach solution of tungsten alloy scraps. Specifically, a magnesium salt combined ammonium solution is employed to precipitate vanadium and impurities in the purification of the leach solution. This separates vanadium from tungsten by rejecting tungsten in aqueous solution. Finally, tungsten is recovered as the form of ammonium para-tungstate (APT). Vanadium is recovered as the form of ammonium meta-vanadate(AMV).

Jan 1, 2003

By A. V. Nozhkina

"Transformation of diamond into graphite was investigated in the region of diamond metastability under the action of media chemically active relative to carbon in the temperature range from 770 K up to 2200 K and pressure range from 10-3 Pa up to 3 GPa/IV VIII group metals of periodic system and oxygen were used as media chemically active relative to diamond.Methods of electron diffraction, chemical analyses, emission spectroscopy and X-ray phase analyses were used for determination of the reaction products.It was found that in the region of diamond metastability the stage of catalytic phase transformation of diamond into graphite took place during the interaction between diamond and metal. Metal reduce activation energy for transition of diamond into graphite from 109,4 kcal/mole to 77,4 kcal/mole.Kinetic of phase transformation of diamond into graphite was investigated.Pressure does not considerably influence on the rate of phase transformation of diamond into graphite in the presence of transition metals."

Jan 1, 2003

By J. B. Rubinstein

"The paper gives an overview of the history of flotation machine development. The laws of their evolution are stated and the place and role of column flotation are demonstrated.The major parameters of column cell diameter and height are discussed. Options are proposed for optimization of the hydrodynamic characteristics of large-capacity column cells. The high efficiency of columns with cell height of 4-6 m is demonstrated. The optimum parameters of multisectional column machines are determined. Their advantages compared to monocells are shown. A scaling-up procedure for column machines was developed based on flotation macro- and microhydrodynamics simulation."

Jan 1, 2003

By Peter N. Holtham, Mary M. Ng

"Resistivity measurements of minerals in the laboratory are commonly made with a low DC voltage source. Common test voltages specified in the ASTM Standard D257 are 100, 250, 500, 1000, 2500, 5000, 10000 and 15000 V, however 100 and 500 V are the most frequently used. Resistivity results obtained in the laboratory have been used to infer the electrical behaviour of minerals undergoing electrostatic separation. However because the voltages employed in electrostatic separation in the plant are of the order of thousands of volts, typically greater than 15000 V, whether the laboratory results are applicable as a predictor of plant performance is a critical question. It is unclear whether resistivity values taken at a low voltage are characteristic of those seen in electrostatic separation, in which the minerals are exposed to a much higher voltage. No definitive answer could be found in the literature.In this work, the resistivities of zircon, rutile and ilmenite were measured in a corona field for the first time. The measurement principle was based on a technique developed to measure fly ash resistivity in electrostatic precipitators, however the test apparatus and findings are novel.Resistivities of rutile and zircon were found to be easy to measure. The values measured in a corona field were several orders of magnitude less than those obtained with a dc voltage of 100 V. Evidence of back corona was observed with zircon. When the voltage drop was greater than the sample layer could withstand a localised electrical stress developed, resulting in a voltage breakdown, at which point a sudden surge of corona current (back corona) was detected in the sample layer. Rutile, on the other hand, exposed to the same conditions as that of zircon (i.e. same temperature and applied voltage) did not exhibit any sign of back corona. Its resistivity across the range of test voltages (14 to 33 kV) remained fairly constant."

Jan 1, 2003

By Jim Petrie, Mary Stewart, Damien Giurco

This paper describes a generic approach to analysing the environmental and economic performance of a generic global mineral/metal value chain, with the express view of improving the quality of prospective decision-making within the industry in order to ensure more sustainable outcomes. As a point of departure we propose that it is not possible to place metals in the context of the sustainable development of society without paying due regard to the entire metals value chain. Thus, the starting point for this analysis is the development of a global stocks flows and transformations model, for the metal of interest. Any aspect of the value chain, e.g. “metals refining, “goods manufacture”, “use and disposal”, can be assessed, either relative to other stages in the value chain, or in more detail by focusing on the technologies used within that stage. The use of this model as a decision support tool is explored here for the case of copper. Both primary and secondary production routes are enumerated, covering a range of processes, for seven distinct geographic regions around the globe. The value of the modelling approach is explored for different energy mixes. In particular, the case study examines the impact of increased recycling on the (re) distribution of global and regional environmental impacts for technologies-in-place in these different regions. The aim of these case studies is to highlight to the minerals processing and metals refining industries their potential role in a more sustainable global society.

Jan 1, 2003

By P. K. Sen, Mrinal K. Ghose

Tailing slurry is usually abrasive and possesses high viscosity. This paper examines the existing iron ore beneficiation process and focuses on some of the key environmental issues related to the disposal of tailings. It identifies that almost 32% of the iron ore extracted ends up as tailings and they are usually disposed in slurry form in tailing ponds. By the year 2000, 27 Mt of iron ore tailings were generated in India, which has become one of the biggest waste handling problems to the industry. Characteristics of the tailings vary widely. So the physical nature of tailings cannot be considered separately in isolation without considering the mill effluent from the beneficiation plant. In the present investigation, studies were carried out in three iron ore mines in India to evaluate the characteristics of tailings from the beneficiation plant. The tailing samples were collected from different locations during a time period of one year and analyzed. The results will be discussed and the characteristics of the tailings have been evaluated. The disposal system of tailings at the three mines was evaluated. The research on the settling characteristics of tailings indicates that the area provided in the existing tailing ponds in India is much more than that of the experimental results. This paper concludes that sedimentation tests are essential to design appropriate tailings pond with respect to size. In the proposed scheme it is suggested that an additional unit process, i.e. sedimentation tank be added to the process before the disposal of tailings to the tailing pond.

Jan 1, 2003

By John Ralston, Jonas Addai-Mensah, Patience Mpofu

The flocculation and dewatering behaviour of kaolinite (non swelling) and smectite (swelling) clay dispersions has been investigated using hydrolysable metal ions Mn(II) and Ca(II) and anionic polyacrylamide-acrylate copolymer (PAM) at pH 7.5 and 10.5. A pH-dependent, specific metal ion adsorption behaviour, accompanied by a marked reduction in particle zeta potential and slurry shear yield stress, was observed to have a profound influence on the colloid stability of both types of clays. Due to the differences in the cation exchange capacity, the smectite clay dispersion required a higher amount of metal ions than kaolinite dispersion to produce similar effects. The adsorption density of the anionic PAM at the negatively charged clay particle surfaces correlated well with metal ion hydrolysis and adsorption behaviour, all of which had a strong effect on slurry settling rate and extent of consolidation. At pH 7.5 where Mn(II) ions hydrolyse, metal ion and flocculant adsorption densities were both greater in the presence of Mn(II) than Ca(II) ions. At pH 10.5, however, where Ca(II) ions begins to hydrolyse, higher adsorption densities were observed for Ca(II) ions in comparison with Mn(II) ions, as the latter hydrolysed completely and precipitated. The metal ion mediated flocculant adsorption led to improved hydrogen bond driven particle bridging and facilitated charge neutralisation flocculation mechanisms which significantly enhanced the dewaterability of both clay dispersions.

Jan 1, 2003

By Sarah K. DeBono, Alan J. Monaghan, Emmanuel V. Manlapig, Gregory J. Harbort

"The Jameson Cell is a type of flotation machine in which air and pulp are brought together in a vertical tube called a downcomer. Within the downcomer the air and pulp are dispersed into a dense foam of fine bubbles, which creates a favourable environment for bubble-particle collision and subsequent collection of hydrophobic particles. The intense collection zone within the downcomer can be considered similar to the zone between the rotor and stator in mechanical flotation cells.Research into the bubble-particle collision and fluid dynamics of mechanical cells rotor-stator zone has been limited by the difficulty of achieving accurate measurements in production sized machines. With the Jameson Cell the downcomer is largely external and separated from the flotation tank, allowing ready access to the primary contacting zone for measurement and analysis.An investigation has been undertaken into the operating characteristics of the downcomer relating to bubble-particle collision. An effective mapping of the downcomer has been made through measurements of void fraction and bubble size taken across cross sections of the downcomer. Analysis of these measurements has provided an interpretation of the variations in the air and fluid dynamics, bubble size and distribution throughout the downcomer chamber."

Jan 1, 2003