Search Documents

By F. S. Niu

With the feature of finely-dissemination particle and complex mineral composition, oolitic hematite is considered to be the ore dressing difficult problem in the world. Series research on refractory oolitic hematite in Zhangjiakou Area are introduced as following: ore properties?technology mineralogy and mineral processing technology. The survey shows: with the fine grinding of the hematite to a fineness of -0.076mm 95%, obtaining iron concentrates grading 62.74% Fe at the recovery of 46.80% by high intensity magnetic separation- reverse flotation flowsheet; under the three stages intensity magnetic separation,four stages grinding and four stages gravity separation, getting the iron concentrates grading 61.09% Fe at the recovery of 45% using high intensity magnetic separation- gravity separation flowsheet; with roasting temperature of 800°C, time for 75~90min and ore-coal ratio of 11, gaining the iron concentrates assaying 62.74% Fe at the recovery of 87% by roasting- magnetic separation flowsheet. At present, this research is still doing for the target of raising the concentration recovery on the base of high grade concentrate. It is in the hope of fully utilizing the existing hematite resources in Zhangjiakou

Jan 1, 2014

By A. V. Yevdokimov, Ye. V. Bogorodsky

The paper presents the results of the research on the development of gravity concentrates processing technology (gold grade is from 50 g/t to 1 kg/t and over) using intensive cyanidation with gold recovery to pregnant solutions followed by precipitation of metals from them using various methods. Test work and pilot plant results confirm that a new developed hydrodynamic regime provides an efficient treatment of gravity concentrates of polydisperse composition without their grinding and preliminary desliming. The resulting pregnant and washing solutions are amenable to metals recovery using electrowinning, cementation onto zinc dust and CIS. Cone plants with a lower ball valve for cyanidation of unground gravity concentrates developed by IRGIREDMET JSC have been successfully tested at a number of Russian operations. Currently, a modular plant equipped with gold electric precipitation from pregnant solution unit is successfully operated at a Russian gold processing plant. Cyanidation of the resulting high-grade gravity concentrate is carried out at the concentration of 8-10 g/L NaCN and 10 g/L NaOH. Gold recovery to the solution is 97-98%. Electrowinning is carried out in flow cell GNC-40M. In this case, the residual gold concentration yield is 0.3-0.5 mg/L. Also, a modular plant for relatively low-grade middlings (50-100 g/t Au) of gravity concentration has been introduced. The concentration of NaCN and NaOH is 2-3 g/L and 1.5-2 g/L, respectively, during leaching. This plant is equipped with a unit for gold cementation from pregnant solution with zinc dust. This cementation unit is of original design. It is made in the form of a filtering device and is composed of several layers of carbon fiber which contacts with zinc powder. The residual gold concentration yield from a cementation unit is less than 0.1 mg/L. Gold recovery is 93-97%. In 2017-2018, the introduction of intensive cyanidation modular plants to gravity concentrates will be planned at new projects of Russia and the CIS.

Jan 1, 2018

By I. Gombköto, G. Mucsi, S. Nagy, F. Kristály, Á. Rácz, R. Szabó, B. Egyed

"Present paper deals with the investigation of a Hungarian pumice. Grinding experiments were carried out in a stirred media mill for various residence time. Ground samples were tested with laser particle size analyzer to determine and calculate the material fineness (particle size distribution and specific surface area). The lime adsorption capacity was measured to monitor the reactivity. Alkali activated cement paste was prepared using ground pumice with various alkali activators. Cube shaped specimens were produced from the paste and the uniaxial compressive strength was measured at the age of 7 days. The resulted alkali activated material structure was investigated by XRD and FTIR. The results of the experiments show that pumice fineness has strong impact on its hydraulic activity, hence on the compressive strength and the structure of the resulted binder. Relationships between grinding fineness, material structure and strength of the raw and mechanical activated material as well as the alkali activated cement were revealed. INTRODUCTION Pumice is a natural pozzolan which can be used as raw material for cementitious materials in limited portion owing to its low reactivity. Furthermore, due to its mineralogical composition it can be used for developing a new environmental friendly binder, namely alkali activated cements (AAC) which are inorganic alumina-silicate materials with good cementitious properties (Almalkawi et al., 2017; Özodabas and Yilmaz, 2013; Najimi et al. 2018; Yadollahi et al., 2015). Despite being a rather recent research topic, many papers and books have been published focusing on various aspects of alkali activation. There is great variety of raw materials that can be utilized for AAC production. However, primary raw materials are very expensive and secondary materials are heterogenous in composition. Therefore, a more homogeneous and low price silicate would help to balance the properties and cost of resulting cement and easing the way for commercialization of AAC. However, the control of its reactivity is of great importance which can be realized using mechanical activation by grinding (Juhász and Opoczky, 1990; Djobo et al., 2016; Mádai et al., 2015). The goal of present paper is to investigate the effect of mechanical activation of pumice on the properties of the resulted alkali activated cement."

Jan 1, 2018

By F. Boylu

In this study, Ca-bentonite was subjected to a series of systematic hydrocyclone tests with the aim of developing separation procedures and in turn achieving optimum recoveries. In hydrocyclone tests, vortex and apex diameters and also feed pressures were investigated. In each hydrocyclone set, vortex diameter was kept constant while the other two parameters varied to produce bentonites con-centrates of various smectite contents. The separation efficiencies were evaluated based on the cation exchange capacity (CEC), particle size and swelling index. The detailed hydrocyclone tests showed that, upgrading of Ca-bentonites require procedures different from the bentonites reported in the literature. Sodium and mixed bentonites are easy- to-disperse and easy-to-separate whereas calcium types need to be scrubbed rigorously for disintegration. Scrubbing properties of ca-bentonite were investigated as a function of scrubbing time and percent solids by weight (PS). The scrubbing conditions at 700 rpm for 1.5 hours and percent solids of 30 % were found more effective for achieving a better quality bentonite. In addition to the parameters mentioned above, the effect of percent solids on hydrocyclone separation was also studied. Although Ca-bentonites permit studying at higher percent solids, increasing solids content of the pulp deteriorated the quality of the clean products. Application of an appropriate separation scheme enabled the development of a unique separation procedure involving stage wise scrubbing followed by hydrocycloning which yielded calcium bentonite concentrates with CEC of 90 meq/100 g and high swelling indexes of 12 mL from the original bentonite of 65 meq/100 g and 7.0 mL, respectively. These results indicate that upgraded bentonite products can be conveniently used in various diverse industrial applications including bleaching earth, desiccant, cat litter, paper etc.

Jan 1, 2014

By R. T. Dec

Current industrial compacting and briquetting practices are largely based on trial-and-error techniques. This paper introduces a two-dimensional finite element model of briquetting process in the roller press. Compared with other modeling techniques used in the past, finite element method offers the most versatile approach because it incorporates adequate information about powder behavior, geometry and frictional conditions and offers predictions for the density distribution, the velocity field, the stress distribution, roll force and torque. More over, when the model includes elasticity, it offers predictions on the internal stress state in the briquette after its exit from the roll. This enables to perform realistic computer experiments which are helpful for establishing the forming cavity geometry and process conditions necessary to produce briquettes with the desired properties. Three forming cavity profiles are analyzed. Results from model are verified on experimental roller press and best cavity profile is recommended for briquetting of sub bituminous coal fines.

Jan 1, 2014

By J. D. Miller, C. L. Lin

In general, x-ray computed tomographic (CT) techniques are able to provide 3D images of the internal structure of opaque materials in a nondestructive manner. The unique cone beam geometry allows acquisition of all 2D projections with only one rotation of the sample thus providing for fast data acquisition and better x-ray utilization, as a complete 2-D detector array receives the cone-shaped flux of rays. Thus, an isotropic 3D volume can be reconstructed without the mechanical translation and the stacking of sequential slices as is the case for more conventional CT scanners. In this regard, a state-of-the-art, custom designed xray microtomography facility to provide very detailed 3D spatial analysis of multiphase particles has been installed and is in operation at the University of Utah. The reconstructed 3D tomographic volume allows for an adjustable spatial resolution from 5 to 20 microns for sample dimensions from 10 to 40 mm in diameter, respectively. Utilization of this custom designed cone-beam x-ray microtomography system is discussed. Applications described include: coal washability analysis for the design and operation of coal preparation plants, liberation analysis for evaluation of grinding practice and separation efficiency, mineral exposure analysis for prediction of the ultimate recovery from heap leaching operations, and analysis of the pore structure network of packed particle beds for simulation of flow through such porous structures as encountered in filtration and heap leaching.

Jan 1, 2003

By I. Yelkin, Erico Tabosa, Alex Jankovic, R. Hayashida, R. Faveere

"The mining industry faces growing challenges from more complex and lower grade deposits, rising costs, limited energy and water availability, and increasing societal pressure to operate more sustainably. Mining operations need to be more efficient, not just to reduce environmental impact, but also to remain economically viable.To maximize profitability and sustainability, existing operations and new projects must consider integration and optimization of all stages of production. A mining operation is essentially a series of inter-connected processes, with the performance and outputs of each stage affecting the subsequent ones. Optimizing stages in isolation can result in sub-optimal overall performance.The industry has long recognized the benefits of holistic optimization using the Mine-to-Mill concept, and there are many well documented successes. However, it is increasingly common to observe operations simply increasing explosive consumption in the mine and expecting optimization of the entire value chain (mining and processing). For true holistic optimization, blast intensity is not necessarily increased, but rather adjusted to best suit the requirements of the different types of ores treated, the circuit configuration and equipment, installed comminution power and the downstream beneficiation processes. It is a fully integrated effort with optimization of many aspects in the mine, comminution and separation processes.To be successful, optimization of the production chain from mine to process requires a site-specific, structured methodology supported by extensive ore characterization, auditing, surveys, data analysis, mathematical modelling simulations and a cost / benefit analysis. Following this methodology, optimization strategies are rapidly identified and implemented considering mine and plant constraints. Management needs to set up appropriate KPIs and site personnel need to be trained for the new operating strategies to be successfully incorporated into site practices and procedures in the production environment. This will ensure the benefits are achieved and maintained. This paper describes the methodology employed by Hatch to improve overall efficiency and profitability from mine to process. Two case study examples at Russian gold operations and benefits achieved are presented."

Jan 1, 2018

By Abhilash

Different methods of utilizing refractory bauxite and disposing red mud are practiced throughout the world, but none of them are known to be environmentally innocuous due to the complexity and /or high cost, and none has been found to be feasible on an industrial scale. Under these conditions, the use of bioleaching process seems promising. The present study emphasizes on the isolation of native extremophiles from the source Indian bauxite and red mud, with their detailed cellular and physio-chemical, and biochemical characterization. These organisms were tested for their ability to thrive in physically or geochemically extreme conditions. The gram positive capsule rich mesophiles and thermophiles were tested for removal of gangue minerals from the bauxite and red mud samples. Keywords: refractory bauxite, red mud, extremophiles, bio-beneficiation, gangue

Sep 1, 2012

By F. Karakas

Organo-bentonite production enjoys important applications including solvent based paints and, more importantly, the production of polymer/bentonite nanocomposites. Quarternary ammonium salts in this regard are still considered as the most versatile reagents in the process of hydrophobization. In this study, a purified form of Resadiye region bentonites, which is one of the most significant sodium bentonite deposits in the world, was used. The raw Na-Bentonite was typically characterized by chemical analysis, XRD and DTA analysis and more importantly for its cation exchange capacity (CEC). Other technological properties such as swelling index, pH, apparent viscosity, water absorption, oil absorption were also conducted on the raw bentonite. The mineralogical analysis of the raw bentonite reveals that it contains about 80 % montmorillonite together with other associated gangue minerals including feldspar, quartz, calcite, dolomite, coloured impurities and other clay minerals. The raw bentonite was subjected to two stage processing involving a series of hydrocylones. Different apex and vortex diameters and different pressures were employed in order to produce a bentonite concentrate with 95 meq/100g CEC from a CEC of 71 meq/100 g. This high quality concentrate was used in the production of organo-bentontonite. The modification was performed with two different quaternary amines, i.e. Trimethyl Phenyl Ammonium Chloride (TPAC) and Hexadecyl Trimethyl Ammonium Bromide (HDTMA-Br). In the modification procedure, three parameters, i.e., adsorption density, zeta potential, swelling index and apparent viscosity were studied simultaneous-ly from the same suspension to identify both the mechanism of the process and also the degree of hydrophobicity. Adsorption measurements were made as a function of conditioning period, pH, and reagent concentration. Simultaneous examination of the adsorption density, zeta potential and apparent viscosity enabled us to pinpoint the optimum region of hydrophobicity which was subsequently tested by settling and critical coagulation concentration in both water as polar and toluene as nonpolar solvents. The results are analyzed in the light of experimental data.

Jan 1, 2014

By Sanchita Chakravarty, Sumantra Bhattacharya, Divya Jyoti, A. K. Mukherjee, Soni Jaiswal

"Release analysis is independent of collector and frother dosage and type, but it is primarily influenced by the degree of liberation or “state of release of the sample”. The shape of release curve is an indication of the degree of liberation. This paper briefs about the effect of reagent combination, particle size and surface characteristics on the release analysis of difficult-to-clean LVC coal.Release analysis of three LVC coal fines obtained from two different coalfields of India was carried out at three different size levels such as -0.5mm, (-0.5+0.1) mm, and -0.1mm. The collectors used were n-dodecane and commercial diesel oil. Incomplete liberation of coal fines even at a size of -100µm, corroborated by photomicrographs of ROM and clean coal macerals, in a great measure reduced the flotation-based cleaning potential of the fines. FESEM images of fines reveals that the adherence of ultrafine onto the surface of relatively coarser particles reduced the clean coal recovery. The results obtained also appear to be coal, reagent combination and, particle size and particle surface specific. Only one coal indicated the liberation as is usually expected for -0.1mm particles with a reasonable yield of 65% at 18% ash. INTRODUCTION Froth flotation has a long history of being used to treat coal fines. Coal flotation is considered to be difficult, if the percentage of Near Gravity Material (NGM), i.e. essentially locked particles, in flotation feed is >10% [Aplan, 1993], which is usually the case with all the coking coal fines in India. The fines are rich in vitrinite, so valuable for coking coal. Unfortunately, there appears to be no standard procedures to determine the separation efficiency of froth floatation. Release analysis proposed by C.C. Dell in 1953 [Dell, 1953], aimed to determine the ultimate floatability of coal. Several other techniques had been proposed but release analysis technique has been considered to be a vast improvement over the batch flotation process [Forrest et al. 1994]."

Jan 1, 2018

By S. Patra, R. Venugopal

"The quality of pellets produced is affected by quality anssastd quantity of green pellets, amount of addition of binders, type of binders added, amount of moisture added along with the other variables like rotation, inclination and fineness of feed. The green pellet quality depends upon chemistry, mineralogy and granulometry of fines used for pellet making, the feed size, its moisture content and porosity. During firing of green pellets ingredients present within reacts to form different phases and microstructure. So in turn physical and metallurgical properties of pellets are influenced by amount and type of binder and flux addition, induration time and temperature. During iron making process, the metallurgical properties of fired pellets are decided by the type and amount of these phases and their chemistry. Green pelletizing and induration studies have been already carried out with hematite ore fines. Indian iron ores of high alumina content showing different pelletizing characters, these studies can’t be directly interpreted. The main objective of proposed research work is to understand the green pelletizing process and determine the water bentonite interaction at different levels. Detailed investigation on swelling behavior of bentonite and microstructure of the green pellets of iron ore fines from SAIL captive iron ore fines from the Barsua in the state of Odisha. To convert these ore fines into pellets, the key raw material, additives and process variables that influence the pellet quality needs to be identified.INTRODUCTION Pelletization is the unit operation of agglomerating iron bearing fines (generally below 150µ with 65-80% passing 40µ) by tumbling in horizontal rotating drums or inclined discs, (Sivrikaya and Arol, 2013; Bhuiyan et al., 2011; Forsmo et al., 2006; Sastry et al., 2003) and the pellets are approximately spherical lumps formed by this process in presence of water and binder, on subsequent induration at 1300°c (Sivrikaya and Arol, 2014; Sivrikaya and Arol, 2013; Sivrikaya and Arol, 2012; Sivrikaya and Arol, 2010; Sastry et al., 2003; Kawatra and Ripke, 2003; Iveson, 2001a; Iveson, 2001b)."

Jan 1, 2018

By B. Rezai

Impeller speed and air flow rate are two influence parameters on coarse particles flotation and collision and attachment angles. So, in this research recovery of quartz particles at four diameter classes carried out and collision and attachment angles investigated. It is found that maximum flotation response was observed at Impeller speed of 1100 rpm and 15 L/h air flow rate. For either more quiescent (Impeller speed<1100 rpm) or more turbulent conditions, flotation recovery decreased steadily. Furthermore, amount of attachment probabilities is calculated using suitable equation. According to this study, with decreasing particle size, air flow rate and impeller speed, probability of attachment increased and with increasing contact angle, probability of attachment increased. For various air flow rates, impeller speed and particle size, collision angle has been calculated. Maximum collision angle obtained at with 15 L/h air flow rate, particle size of 256 µm and impeller speed of 700 rpm and minimum collision angle obtained at with 45 L/h air flow rate, particle size of 545µm and impeller speed of 1300 rpm. In this study, maximum attachment angle, , was around 75 L/h air flow rate, particle size of 256 µm, contact angle of and impeller speed of 1300 rpm and minimum attachment angle was with 15 L/h air flow rate, particle size of 545 µm, contact angle of and impeller speed of 1300 rpm. ?82.72 ?64 cr??33.39 ?90 ?13.0 ?60

Jan 1, 2014

By Anand Anupam

Conventionally, beneficiation in Indian coal washeries is done using dense medium cyclones upto the size of 0.5 mm. Coal fines below 0.5 mm size are extensively cleaned by froth flotation. There are many problems associated with flotation of Indian coals, e.g. poor response of coal particles to flotation, misplacement of fine high-ash material to froth, loss of good quality coarser coals (within ?0.5 mm size range) to tailing streams, high cost of reagents, water contamination, etc. In addition, sophisticated control systems for efficient management of the fines washing circuits are needed. Thus, there is an escalation in the capital and processing costs. In view of these facts, studies were carried out to establish the cleaning potential of dense medium cyclones for beneficiation of fine coal down to a size of 0.1 mm, essentially aimed at reducing the load on fine coal circuits mainly comprising of flotation. ROM Coal (in the size range of -2 + 0.1 mm) obtained from JogtaOCM,Jharia coalfield possessing relatively low ash (about 21%) was used in this study. Purpose for using low ash coal was to further lower, its ash content down to 8% which is comparable, to the ash content of imported coal. After characterization studies, nine tests were carried out on the prepared feed sample for its beneficiation using a dense medium cyclone of non-conventional design (very low cone angle and longer barrel), by varying its apex and vortex finder diameters. The efficiency of separation has been evaluated using Tromp curves. It could be established that it is possible to produce a clean coal of 8% ash, with Ep value of 0.044, using Jogta OCM coal by treating it in a modified dense medium cyclone. These results are summarized and discussed in detail in the present paper. Keywords: dense medium, cyclone, fine coal, beneficiation, Jharia coal

Sep 1, 2012

By T. Fraszczak, U. A. Peuker, T. Mütze, T. Leißner, A. Wikedzi

The present paper highlights on the comminution and liberation properties of two greisen-type lithium bearing-mica ore blends (L1, L2) subjected to different breakage devices; cone crusher (CC), roller crusher (RC), rotor beater mill (RBM) and a screen mill (SM). The particle size distribution (PSD) of the products from each device were evaluated to search for an appropriate PSD model using Gates-Gaudin-Schuhmann (GGS) and Rosin-Rammler (RR) functions. In order to determine an appropriate function that could better describe the PSDs from the devices used, the coefficient of determination (R2) was used as a criterion. In terms of mineral liberation studies, due to costs, only products from rotor beater mill (RBM) were examined through an automated scanning electron microscope (SEM) technique. It was found that RBM, RC and SM products were better described by the RR model than the GGS model with higher R2 values (0.97-1.0). However, cone crusher products for L1 were better described by GSS model, while that for L2 were better described by RR model. In terms of the spread of size distribution as indicated by RR model parameters, RC products were more uniformly distributed compared to products from other devices, for both ore blends. Also the RBM products were more scattered than products from other devices. The results indicate that the composition of individual ore blends affected the comminution products PSDs since different PSD model parameters were obtained for samples comminuted by same devices. The modal mineralogy of the two ore blends indicate both to be rich in quartz, topaz, zinnwaldite and muscovite. Further, the result indicate that, for both ore blends, zinnwaldite phase is more enriched in the fraction < 250 µm. Moreover, better liberation of zinnwaldite is observed for L1 compared to L2. This could be explained by differences of the two ore blends in three aspects; the nature of mineral association, reduction ratio of the fractions analysed and the nature of spread of the size distribution.

Jan 1, 2018

By V. Sheikhzadeh, M. Saghaeian, R. Hejazi, A. Abazarpoor

Green pellet strength including drop number and green compression is highly depended on particles size and shape. The used grinding method, ball mill or high pressure grinding roll (HPGR), directly vary the particle size and shape. Considering mode of pellet crack, green pellet is composed of particle-binder-moisture system. Different type of forces existed in such a system to create a stable green pellet: solid particle interaction, magnetic, binding and cohesive forces in the interface of particle-moisture. The pellet failure can occur at solid-liquid interface and/or through liquid phase. Pellet crack occurs when crack passed through entirely the plane failure. In this research, the effect of particle size and shape of pellet feed on green pellet strength has been investigated. It was deduced that green pellet strength highly improved by increase of specific surface area. The drop number and green compression strength of pellets prepared by HPGR was higher than ball mill. It was found that the main reason responsible for this difference was the particle shape. Capillary force is responsible for part of pellet force and improves by decrease of particle size. Also more elongated shape of HPGR particles resulted in higher capillary force due to thinner interface layer between particles. The less circular shape of particles lead to improvement of capillary force as can be occurred for HPGR particles. The rougher shape of HPGR particles resulted in higher wettability of particles and better diffusion of water among particles. In fact the rougher particles means lower connection angle. Aspect ratio of particles was of great importance of crack growth because the required energy of pellet failure increases directly. The required energy for pellet failure increases by increment of particle aspect ratio. The relationship among crack failure force, roughness and aspect ratio has been modeled considering 3 shape descriptors.

Jan 1, 2018

Over the last four years, a major collaboration between CSIRO-MIS, UCT and JKMRC has produced two significant advances in the modelling of comminution. The Universal Comminution Model (UCM) uses parametric SPH/DEM studies of comminution and separation devices to calibrate mathematical models which are suitable for industrial use. The Virtual Comminution Machine (VCM) uses the same computationally intensive techniques based on discrete element modelling (DEM) and smoothed particle hydrodynamics (SPH) to directly model any comminution device by combining a CAD file describing the machine design, sophisticated ore characterisation methods and advanced particle scale flow and breakage simulation. The UCM should be useful for process analysis and optimisation of existing equipment and circuits while the VCM should make a major contribution to the evaluation and development of new machines. Progress to date is encouraging with several processes now well described using DEM. This paper also reports on progress towards combining DEM for particles with a realistic slurry model based on SPH for different types of comminution devices. In due course, this combination should allow accurate modelling of particle transport in wet mills to be combined with DEM models.

Jan 1, 2014

By V. I. Ryaboy, I. V. Ryaboy, E. D. Shepeta

"The problem of separation of copper minerals and arsenopyrite remains relevant because of environmental requirements. The selective action of reagents with the thioamide group (thioamides) is known in iron sulfide’s flotation of pyrite and pyrrhotite. The aim of this study was to reduce the arsenic content in the copper concentrate when using thioamides by reducing the flotation of arsenopyrite in the flotation of the sulfide part of the skarn scheelite-sulfide ores. We have chosen the most widely used thioamides for the study, such as Z-200. We also synthesized new reagents with the thioamide group. The most selective and the most powerful thioamide copper collector were used for further studies. Reduction of arsenic content in copper concentrates is achieved in the following way: You need to apply a strong thioamide collector with a selective but weak dialkyldithiophosphate collector, or vice-versa, a selective, but a weak thioamide collector should be used with the dialkyldithiophosphate reagent with strong collective properties. The proposed combination presents industrial interest because of its accessibility. The application of thioamides in copper minerals and arsenopyrite selection has showed that these reagents have fewer selective properties than dialkyldithiophosphates. To achieve the comparable recovery of copper using dialkyldithiophosphates requires markedly greater consumption of thioamides, due to their lower hydrophobic ability. The application of a composition of thioamides and dialkyldithiophosphates allows to increase the recovery of copper and to obtain a lower arsenic content in copper concentrates compared to their individual use. The lowest arsenic content in the copper concentrate is obtained in the composition consisting of the newly synthesized thioamide with strong collective properties and selective dialkyldithiophosphate. The addition of even small amounts of xanthate to the composition of thioamides and dialkyldithiophosphates causes a sharp increase in the arsenic content in the copper concentrate without a notable increase in copper recovery."

Jan 1, 2018

By Dmitriy Kim, Natalya Ibragimova, Galina Sedelnikova

Gold and copper are lost in flotation tailings in mineral processing of copper-zinc-pyrite ores. Large resources of precious and base metals have accumulated in tailing ponds of Russian plants. Object of the study is the sample obtained from Ural Mining and Metallurgical Company in Russia. The main constituents in flotation tailings are Au, Ag, Cu and Zn with content 1.4 g/t, 12 g/t, 0.66 and 0.5% respectively. The flotation tailings are a refractory material. Gold, as main metal, is fine encapsulated in sulfides, mainly in pyrite. Gold extraction from tailings is 34.0 and 42.7% at P42 and P90 of 0.074mm particle size respectively. In this work heap bioleaching of tailings was studied for oxidation sulfides (pyrite and chalcopyrite) with using mesofilic and moderately termofilic bacteria in acidic solutions. The tailings had low filtration property (< 0.3 m/day) and pelletization was used before bioleaching. Copper containing converter slags flotation tailings and calcium oxide were used as binding material for increasing filtration property of tailings. Copper was extracted in sulfate solution and was precipitated by cementation after cleaning of bacterial solution from iron. Copper recovery was 56.8% at content 61.4% in precipitate. The biooxidation of pyrite was 80%. Cyanidation, leaching with thiourea and heap leaching by cyanide were tested too. Gold extraction from solid bioresidues was 82, 75.3 and 77% respectively. The results of this investigation were recommended for pilot test.

Jan 1, 2014

By Paulo Braga, Carlos Junior, Silvia França

"Lithium is the lightest of the metals, with high reactivity and great electrochemical potential. It has a low thermal expansion coefficient and high caloric value, and it forms very light and resistant aluminium alloys. These properties make lithium an attractive element for use in battery manufacture and glass and ceramics production, in addition to its applications in the aeronautic industry. Today, two sources of raw material are economically viable for lithium production: pegmatite rocks and brine. The world production, in 2012, was approximately 150,000 tons of LCE (lithium carbonate equivalent), almost triple the production in 2000. The forecasted consumption for the current year, 2013, was approximately 162,000 tons of LCE, and for 2020, it could be as much as 280,000 tons of LCE, stimulated essentially by the growth of world production of electric (EV), hybrid (HEV) and hybrid plug-in vehicles (PHEV), the batteries of which are based on Li-ions. With the growth of world demand and increasing prices, lithium minerals such as spodumene, petalite and amblygonite, once considered uneconomical for the production of lithium carbonate, are regaining their economic value. New projects to produce lithium compounds based on mineral sources are being developed in many countries, aiming to produce battery-grade lithium carbonate (99.95% Li2CO3). Although Brazil has large lithium pegmatite reserves, the domestic production of lithium carbonate and hydroxide is very low, at approximately 600 tons of LCE, which represents 0.4% of the world production. The application of these products is mostly in the grease and ceramic industries. The national lithium market is under government protection due to its potential use for nuclear purposes. Thus, the industrialization activities and import and export of ores and lithium minerals, as well as organic and inorganic products, such as metallic lithium and lithium alloys, are controlled by the National Commission for Nuclear Energy (Comissão Nacional de Energia Nuclear - CNEN). The objectives of this work to quantify the real lithium demand in the Brazilian market, considering that a large amount of lithium is indirectly imported in the form of the Li-ion batteries used in equipment such as mobile phones, cameras, tablets, notebooks and e-bikes, and to compare this demand with the current national production of LCE. Finally, some technological alternatives will be discussed, with the aim of increasing the competitiveness of the lithium industry in Brazil."

Jan 1, 2014

By J. Quinteros-Riquelme

Despite increasing demand, the supply of silver is limited by its inadequate recovery from ores. Due to its scarcity in nature, its high ore variability and complex mineralogy of current silver deposits, its recovery by mineral froth flotation presents a real challenge for process engineers. A silver ore often contains significant amounts of five to ten different silver minerals and knowledge of the mineralogy is a necessary precursor to flotation testing. In this work, a complex silver ore was treated by using batch laboratory flotation, in an effort to find the best experimental conditions to obtain the optimal silver recovery. Mineralogical characterization of feed samples was conducted using a combination of tools, namely the mineral liberation analyzer (MLA) and inductively-coupled plasma mass spectrometry (LA-ICP-MS), which indicated that most of the silver occurred as ?invisible? silver in pyrite. The pyrite assay of the ore was approximately 4%. The ore was processed in two flotation stages. The first stage, sulphide flotation, aimed to collect a sulphide mineral rich concentrate; then a non-sulphide flotation stage was performed by adding sodium sulphide and collectors to the remaining material in the cell, with the objective of obtaining a pyrite rich concentrate. To reach the target recovery of silver from this ore, various variables were altered. In the first stage: mixed collectors, activators, dispersants, and mainstream inert grinding were assessed. In the second stage, the conditions for sulphidization and subsequent flotation were both investigated. From the grade recovery curves for silver and sulphur it was possible to observe a similar metallurgical behavior for both elements, supporting the results given by the mineralogical characterization. Keywords: silver oxide, froth flotation, sulphidization, mig

Sep 1, 2012