Search Documents

By Dwight D. Trueblood

The Benthic Impact Experiment (BIE) is designed to address the effects of sediment redeposition prior to the commencement of commercial mining. The experiment is being conducted in collaboration with Russian scientists from the Yuzhmorgeologiya Association aboard the R/V YUZHMORGEOLOGIYA. Sediment resuspension and subsequent redeposition during manganese-nodule mining is predicted to be one of the primary impacts on benthic communities living on the abyssal seafloor. The redeposition thicknesses that will cause significant faunal mortality in the deep sea are unknown. Sediment redeposition could adversely affect abyssal benthic communities through entombment, or through starvation caused by food dilution and obstructed feeding. This spring NOAA conducted the main portion of the BIE experiment, blanketing the experimental area with varying thicknesses of sediment using the Deep Sea Sediment Resuspension System (DSSRS). The DSSRS was conceived by NOAA scientists, designed and built by Williamson and Associates, and is the critical piece of equipment used to generate the controlled sediment redeposition environment on the 4800-m deep abyssal plane. The DSSRS consists of an 1800-kg sled, 4.8 m long, 2.4 m wide, and 2.2 m high. The sled was towed and powered using an 8,000-m, 26-mm single conductor cable having a 3,000 VAC capacity. As the sled was towed across the bottom, mud was ingested through two rear-facing, 45-cm wide intakes using two 7.6-horsepower pumps, and discharged 10 to 20 m above the bottom through two 20-cm diameter riser hoses. Each pump was instrumented with optical backscatter sensors providing real-time information about the discharge concentration.

Jan 1, 1992

By Jelena Milinovic, Sofia Martins, Anna Lichtschlag, Sven Petersen, Fernando J. A. S. Barriga, Bramley Murton, Adeline Dutrieux

"The active TAG hydrothermal mound is one of the largest and better studied. Due to its size (one of the largest, known so far, in the Atlantic Ocean) and concentration of specific economic valuable elements, it might be considered for future exploitation due the increasing demand for raw materials. However, the discovery of several large inactive sulfide mounds, some partially buried under sediments may relieve this pressure. Exploration for such occurrences can, together with geophysical exploration tools, be accomplished by mineralogical and geochemical studies of those sediments.INTRODUCTION AND GEOLOGICAL SETTINGThis study reports the results from sediment samples collected during the Meteor M127 cruise on the TAG hydrothermal area in 2016. The Trans-Atlantic Geotraverse (TAG) hydrothermal field (Mid-Atlantic Ridge, 26°08’N) is located 2.4 km east of the main rift valley at depths of about 3650 m. The TAG hydrothermal field stands as an example of a massive sulfide deposit on a low-spreading ridge associated with an active detachment fault (Humphris et al., 2015).Associated with the TAG hydrothermal field are metalliferous sediments/deposits that can reach several meters in thickness (Metz et al., 1988). These sediments/deposits can be formed by hydrothermal plume fall out (buoyant and nonbuoyant), massive wasting of hydrothermal edifices (sulfide mounds and chimneys) and authigenic mineralization (Gurvich, 2006). By studying the grain size, mineralogy and geochemistry of the sediments it is possible to identify each type of sediments and find their proximal or distal distribution. The location of the gravity cores studied here is distributed along sediment ponds near inactive hydrothermal mounds [Three mounds area (B)], actively venting low-temperature mound [Shimmering mound (A) and Mir zone (D)] and an area of sediment accumulation [Central area (C)] (Rona et al., 1993) (see Figure 1)."

Jan 1, 2017

By Peter M. Herzig

In 1994 and 1998 the German research vessel R/V Sonne undertook detailed mapping and sampling of the largely uncharted offshore areas of the Tabar-Lihir-Tanga-Feni island chain in the New Ireland Basin of Papua New Guinea. The New Ireland Basin occupies a fore-arc position with respect to the formerly active Manus-Kilinailau arc-trench system and hosts a series of Pliocene to Recent alkaline volcanoes which are built on rifted Miocene sedimentary basement. Several of the volcanoes possess high-level porphyry stocks and active geothermal systems, including gold-depositing hot springs and the giant (40 million ounces) Ladolam gold deposit on the island of Lihir. On the southern flank of Lihir island, a group of three volcanic cones were discovered at water depths from 1.000-1.500 m. The volcanoes are located in a narrow zone of recent seismic activity and elevated heat flow (up to 100 mW/m2). The recovered volcanic rocks consist of fresh alkali-olivine basalts, clinopyroxene-rich basalts (ankaramites), porphyritic phlogopite basalts, and trachybasalts. Unusual gold-rich hydrothermal precipitates were recovered from the summit of the 600 m high Conical Seamount located only about 10 km south of Lihir Island. 1200 kg of sampled material systematically collected with a TV-guided grab from the top plateau (150 x 200 m, 1.050 m water depth) are intensely mineralized with pyrite, marcasite, minor sphalerite, chalcopyrite, galena, tennantite/tetrahedrite, and orpiment/realgar together with traces of anglesite, cerrusite, and amorphous silica in stockwork-like veins. Bulk samples of the vein mineralization consist mainly of clays, silica, and disseminated sulfides, and have an unusual high gold content ranging from 1.2-44.0 ppm Au. In some of these samples, grains of native gold (about 1 micron in diameter) were identified by SEM in pyrite and sphalerite. The gold-rich material also contains high concentrations of silver (up to 1000 ppm) and typical epithermal elements such as As (2.6 wt.%), Sb (0.2 wt.%), and Hg (34 ppm). Similar to epithermal deposits on land, which usually have only low base metal contents, the samples from Conical Seamount contain only minor amounts of Zn (max. 4.5 wt.%), Cu (2.0 wt.%), and Pb (2.0 wt.%). Many of the samples recovered from Conical Seamount are virtually identical to the gold ore at Lihir.

Jan 1, 1998

By Natalia Konstantinova, Kira Mizell, James R. Hein, Georgy Cherkashov, Amy Gartman, Pavel Mikhailik

INTRODUCTION Ferromanganese (FeMn) crusts from Mendeleev Ridge, Chukchi Borderland, and Alpha Ridge, in the Amerasia Basin, Arctic Ocean, are similar based on morphology and chemical composition. The crusts are characterized by two- to four-layered stratigraphy. The chemical composition of the Arctic crusts differs significantly from hydrogenetic crusts from the North Pacific Prime Zone (PCZ; Hein et al., 2013), such as a high mean Fe/Mn ratio (2.6 versus 1.3) and low Si/Al ratio (1.8 versus 4.0), with lower Mn, Ca, Ti, P, Ba, Co, Cu, Ni, Pb, Sr, and Zn and higher Si, Al, Mg, As, Li, V, Sc, and Th. Based on Arctic FeMn crust mineralogy, chemical composition, and growth rates, crust formation was dominated by three processes: Precipitation of Fe-Mn (oxyhydr)oxides from ambient ocean water, sorption of metals by the Fe and Mn phases, and fluctuating but large inputs of terrigenous debris (Konstantinova et al., 2017; Hein et al., 2017). The Mn and Fe phases are hydrogenous and reflect bottom ocean-water chemistry and the aluminosilicate phase contains stable detrital minerals such as quartz, feldspars, zircon, monazite, and clay minerals. A precise method of studying the distribution of elements in FeMn crust phases is sequential leaching that dissolves four mineral phases of different stability step-by-step, in the following order: easily leachable phase, mostly bio-calcite; manganese oxides; iron oxyhydroxides; and residual aluminosilicate minerals (Koschinsky and Halbach, 1995). Twelve bulk crusts and crust layer samples obtained from six hydrogenous FeMn crusts were studied. Those crusts were collected during Russian (Arktika 2012) and USA (HLY0805, HLY0905, and HLY1202) research cruises from different parts of the Amerasia Basin (Mendeleev and Alpha Ridges, Chukchi Borderland). Samples were chosen for the sequential leaching experiments based on their morphology, location, and water depth. Hydrogenetic crust (D07-33) from the Tuvalu EEZ, central-west Pacific Ocean, was included in the experiment for comparison. Recovery during the four-step sequential leaching, with respect to the bulk analyses, was between 80% and 120%.

Jan 1, 2018

By Sofia Martins, Anna Lichtschlag, Sven Petersen, Fernando Barriga, Bramley Murton, Adeline Dutrieux

"Sediments in the vicinity of the hydrothermal seafloor massive sulphide (SMS) mounds are characterized by high concentration of metallic particles. They result from a long process of weathering of the primary mineral deposits and have been accumulated in depressions by mass wasting and hydrothermal plume fall-out. We present here the first results obtained on pore waters analyses of such sediments in distinct geological seafloor environments (in low-temperature hydrothermally active zones, on extinct hydrothermal mounds and in a remote depositional channel). Vertical concentration profiles suggest that the pore fluid composition is affected more by seawater circulation compared with hydrothermal fluid flow in all environments. The composition of pore fluids is affected by diagenesis and redox processes in the distal depositional channel where Mn2+ is released at depth with Cu2+.IntroductionMarine hydrothermal fields, hosting seafloor massive sulphides, are potential resources for future deep-sea mining and might become economic reserves for the industries. They are widespread at mid-oceanic ridges, arcs and back-arc spreading centers (Hannington et al., 2011; German et al., 2016). Sediments in the vicinity of these fields can contain unusually high concentration of Fe, Mn, Zn and Cu among other metal elements (Shearme et al., 1983). These hydrothermal, or metalliferous, sediments result from a combination of processes such as collapsing and weathering of chimney material, filling of the channels by turbidite-like mass wasting, in situ authigenic mineralization and hydrothermal plume fall-out (Goulding et al., 1998; German et al., 1990). The sediments contain important indicators reflecting the development of the hydrothermal systems. Because of their widespread distribution and metal content, they themselves can be considered potential mineral resources. Circulation of seawater through these deposits, however, often modifies the sediment composition by oxidizing the sulphides into oxyhydroxides and clays causing mobilization of the metals. To address the importance of alteration and diagenesis of these hydrothermal sediments, including the result of seawater circulation, we investigated the post-depositional processes occurring in the hydrothermal sediments at the TAG Hydrothermal Field (Mid-Atlantic Ridge, 26°N), focusing on the mobility of metallic cations in a number of different seafloor environments."

Jan 1, 2017

By Gérald Riverin

Over the past century, exploration methods for volcanogenic massive sulphide deposits have evolved in response to a decreasing number of discoveries made by traditional surface prospecting and by ground and airborne geophysics. Statistical trends support the concept that fewer and fewer outcropping and sub-cropping VMS discoveries will be made in the future. In turn, this creates new opportunities to develop more sophisticated exploration models and techniques to explore at greater depth and to make blind discoveries. Current exploration models include various combinations of geological, geochemical and geophysical criteria which have been based on the results of land-based VMS research. The role of seafloor research in the development of these models has so far been only of a subordinate nature, perhaps due to a lack of direct involvment of the exploration industry in the seafloor research, and vice-versa for the seafloor researchers in VMS exploration. Another contributing factor is that exploration relies on exploration criteria that result from detailed geological, geochemical and geophysical studies of both footwall and hanging wall rocks, studies that are not possible in modern sea floor environments. Nevertheless, seafoor research has contributed to our understanding of the growth of sulphide mounds, the mechanism of sulphide deposition and of the chemistry of fluids involved in VMS systems. In particular, the role of structure and of tectonic setting has been clarified through observation of active seafloor hydrothermal systems. In turn, observations made in land-based VMS research has helped seafloor researchers to focus on key issues which, will eventually contribute to improved exploration models.

Jan 1, 1998

By Peter Halbach

The two HYFIFLUX cruises of the German RV SONNE (SO 99/1995 and SO 134/1998) were organized in the framework of a co-operation between several German universities and two European marine research partners. It is a multidisciplinary program for the study of hydrothermalism with its associated geological, mineralogical, and biological processes in the North Fiji Basin (NFB) in the SW-Pacific. The main achievements of the HYFIFLUX cruises were detailed multibeam Hydrosweep mapping in order to identify the detailed tectonic setting, water sampling at hydrothermally active vents, mineral sampling at inactive sites with sulfide, sulfate, and silica mineralizations, and sampling of basaltic rocks, (Halbach et al. 1999). Oceanic accretion in the NFB is characterized by a double spreading system (Auzende et al. 1994),with one spreading axis located in the median part of the basin (Central Fiji Ridge, CFR) and the second one located immediately west of the Fiji platform (West Fiji Ridge). Most of our investigations were done in the northern part of the N 15° segment of the CFR, which corresponds to area A of our program, area D is located farther south in the NFB and corresponds to the N-S segment of the CFR (Fig. 1). During previous works under the French-Japanese STARMER project, the active ?White Lady? mound and the extinct Père Lachaiseí site were sampled; these samples were studied by Bendel et al. 1993. Here an inactive hydrothermal field was studied, where there were many sediment-covered chimneys in various stages of disintegration, (Bendel et al. 1993). However, the area immediately southwest of the nodal circular basin, which is the triple point junction of the medium-spreading Central Fiji Ridge (about 6 cm/yr spreading rate

Jan 1, 2000

By Manfred Krutein

Ocean mining has a number of problems which are critical to its development: ? Political hurdles on national and international stages ? The worldwide economic situation, with the possibliity of a recession ? Financial difficulties in funding further work ? Technical problems for the development of ocean mining and transport subsystems ? Demands for technology transfer This paper touches the last two points and provides some thoughts for discussion and creative objectification. The many technical problems of ocean mining will be identified and some proposed solutions will be investigated relative to the state-of-the-art technology of ocean mining and nodule transport. An outlook into the future attempts identification of the steps necessary to eventually develop components for workable systems that are not only technically but also economically feasible.

Jan 1, 1978

By Charles L. Morgan

"In 2012 the International Seabed Authority (ISA) established nine “Areas of Particular Environmental Interest” (APEIs) for consideration as future Marine Protected Areas to help preserve the biodiversity of life on the seabed within the Clarion-Clipperton Zone (CCZ) between Baja California, Mexico, and the Hawaiian Islands. The CCZ is believed to have a high potential for future seabed mining operations. Areas under active exploration contracts in the CCZ, plus the areas currently reserved by the ISA for exploration by developing nations, comprise about 1.9 million km2 of seabed area. The currently designated APEIs consist of more than 1.4 million km2 of seabed. Each APEI includes a central primary conservation area of 200 X 200 km, surrounded by 100-km buffer areas on all sides. The 100-km buffers are intended as a very conservative spacing between the primary conservation area and potential mining activities in adjacent seabed. The selection of these nine 400 X 400 km APEIs, has been criticized as possibly not including sufficient representative habitat similar enough to the potential mining areas (identified currently as the exploration contract and reserved areas administered by the ISA within the region) to ensure protection of the biodiversity that might be impacted by mining.An area to the east of the existing exploration contracts and reserved areas is known to have substantial mineral deposits; it is very similar to the adjacent exploration contract areas in its geology, environmental setting, polymetallic nodule abundance and nodule metal content. Because it is located in the northeastern extreme of the CCZ, this area is also likely to have relatively high densities of benthic life, compared with benthic communities further westward within the CCZ. Many options for the designation of this APEI are possible, but the area designation must accommodate the boundaries of the Exclusive Economic Zones of Mexico and France.This paper discusses why the selected region in the eastern extreme of the CCZ is a good candidate for designation as a new APEI.Keywords: polymetallic nodules, Marine Protected Areas, Clarion-Clipperton Zone, Areas of Particular Environmental Interest"

Jan 1, 2017

By H. I. Chesalova, M. Ye. Melnikov, A. M. Asavin

The discovery of iron-manganese ores on the surface of underwater mountains was made more than a half century ago. During this time the basic ideas about the thermodynamics of the processes of hydrochemical reactions in the sea water have been developed by scientists and are revealed in geochemical and mineralogical differences between the deposits from the seamounts and the nodules of the sea bottom. The distribution of the dissolved metals, oxygen, carbonic acid and organic matter in the overlying ocean waters of seamounts in the deep ocean to depths more than 5,000 m has been studied in some detail (e.g. J.R. Hein, P. Halbach. G.B. Baturin, Ye.M., S.I. Andreev, L.I. Anikeyeva, [1-6]). In recent years scientists from YUZMORGEOLOGY have completed detailed geological survey work on the Magellan Seamounts in the Pacific Ocean. The results of drilling the ore body and geophysical and photo surveys have also been described [4]. Previous ideas about the general covering of seamount surfaces with iron-manganese crusts have been changed based on ground-truth surveys. This study examines the complex concentric-zone or spotty arrangement of the most densely covered sections, the strong dependence of the thickness of crust on the geomorphologic features, and the potential influence of the underlying substratum. One established geochemical heterogeneity in the composition of ores, also frequently inversely proportional power dependence on directions was observed. The development of a numerical model of the formation of the ore crust on the seamounts is currently a high priority.

Sep 24, 2006

By NA UMC

Abstract Booklet

Dec 2, 2023

By Ivo Dreiseitl

Bottom sediment sampling by means of a box corer, as a direct method of deep seabed exploration for polymetallic nodules, is the most comprehensive way to obtain various types of geological information on points forming a network of stations. However, direct information is lacking from areas separating those stations and has to be approximated by interpolation or extrapolation, which leads to uncertainties. Sediment sampling with a gravity or piston corer can provide information on the superficial, up to 4 m thick, part of the sedimentary cover. As opposed to box coring, gravity or piston coring provides no information on nodule abundance. Information for unsampled areas can be gained by application of remote techniques of exploration. The techniques of choice in visualising nodule-rich fields, nodule-free areas, hard rock outcrops and other obstacles for seafloor mining involve using sonar and continuous deep sea (CDS) camera. Seafloor mapping can be rendered with two major sonar types: the side scan sonar used to obtain seafloor imagery and multibeam sonar for bathymetric data; the two types are usually combined and work with an intermediate frequency profiler. Photo-profiling by means of a deep sea towed camera provides a series of seafloor photographs, each supplemented with information on the area covered by each frame, including the nodule abundance. Remote techniques have been quite frequently applied by the Interoceanmetal Joint Organization (IOM) in nodule field exploration. Recently, geoacoustic techniques (side scan sonar + profiler) and CDS were applied for exploration of IOM?s first prime area H11 (5372 km2) on 6 transects. During the IOM-2009 cruise, a total of 295 km of geoacoustic transects and 344 km of photo-transects were surveyed. The data obtained were processed with the aid of earlier information produced by multibeam sonar surveys. The aim of this paper is to demonstrate the advantages of remote techniques, particularly with regard to application of the towfish device, for geological and geotechnical applications in exploration for polymetallic nodules.

Sep 14, 2011

By NA UMC

Abstract Booklet

Dec 1, 2022

By Mayumi Ito

Seafloor hydrothermal deposits are found worldwide at 700 to 3,600 meters below sea level [1] and contain base and precious metals like Cu, Pb, Zn, Au, and Ag. Some deposits were found in the Japanese exclusive economic zone and the commercial potential will depend on developments in mining and treatment costs of onshore mines. The ores require mineral processing to become concentrate for the various metal smelters and the authors are investigating mineral processing treatments of collected samples. The collected samples were classified into three components (chimney, mounds, and substrate rocks) and they were separated using a RETAC jig. The mound component contains zinc, lead, and copper minerals and further separation using flotation was investigated. This paper introduces results of the mineral processing tests using gravity separation and flotation.

Jan 1, 2011

By Matthew Kowalczyk, Steve Bloomer, Peter Kowalczyk

"Mineral deposits found near seafloor hydrothermal venting are of great economic interest. Valuable metals such as gold, copper, zinc, and other polymetallic sulfides are found in appreciable grades in seafloor massive sulfide (SMS) deposits associated with these vents. For mapping these deposits, electromagnetic prospecting is one geophysical method that is very useful because copper/gold rich deposits are highly conductive.Ocean Floor Geophysics (OFG) in 2008 developed the first EM system to successfully map the limits of conductive mineralization in a survey at the Solwara 1 deposit (Kowalczyk, 2008). Since then, towed coincident loop time domain systems have been developed by Waseda University (Nakayama and Saito, 2016) and have successfully detected known mineralization buried at 30m depth. Using a deep tow controlled source electromagnetic (CSEM) array, very clear anomalies have been measured (Murton, 2017) over known mineralization at the TAG field on the mid-Atlantic ridge.In 2014 and 2015, OFG partnered with Fukada Salvage and Marine Co. Ltd. and the Scripps Institution of Oceanography to map methane hydrate deposits off the coast of Japan using a towed controlled source electromagnetic (CSEM) system developed by Scripps. These hydrate deposits are resistive targets, and the Scripps system successfully mapped subsurface electrical resistivity distributions to depths of several 100 metres below the seafloor. OFG is attempting to extend the Scripps CSEM technology to map subsurface conductive SMS deposits to a similar range of depths below the seafloor."

Jan 1, 2017

By Jeremy Spearman, Mark Lee, Jon Taylor, Neil Crossouard, Bramley Murton

"SUMMARYThis paper describes challenges faced when executing a programme of monitoring to measure the dynamics of currents and sediment plumes at a seamount and the solutions identified to deliver the measurements. The study site was the Tropic Seamount, which extends some 3300m above the surrounding seabed and is found at the southern limit of the Canary Island Seamount Province. The purpose of the study, which forms part of the Marine E-tech project, was to provide information on the interaction of flows with the seamount and to assess the behaviour of sediment plumes that could be generated from potential seabed mining operations targeting the recovery of ferromanganese crusts. Since the crest of the seamount is submerged to a depth of 1000m, much of the work was undertaken using remotely operated and autonomous vehicles supported by measurements from the surface vessel. Despite only limited information on currents being available for planning purposes, the combination of short term forecasting using a 3-dimesional hydrodynamic model of the study area coupled with the collection and analysis of reconnaissance data collected during the first phase of measurement activities made it possible to plan and execute a number of detailed hydrodynamic experiments on the seamount crest. The results of these experiments have advanced the understanding of the behaviour of sediment plumes in the deep ocean and will ultimately improve our ability to manage the impacts which may arise from deep sea mining operations."

Jan 1, 2017

By J. W. Jamieson

INTRODUCTION Hydrothermal vents that form seafloor massive sulfide (SMS) deposits represent unique biodiversity hotspots that host many species that are found only at these sites. The destruction of these habitats remains one of the greatest environmental risks associated with proposed mining of SMS deposits. For this reason, there is a growing movement to protect active vent sites from direct and indirect effects of seafloor mining (Van Dover et al., 2018). Mitigating the adverse effects of mining on these ecosystems may prove to be one of the greatest challenges facing the marine minerals industry. At the same time, there is increasing evidence that inactive or extinct hydrothermal systems, which do not host the density or diversity of animals typical of active vents, may constitute a significant proportion of the SMS resource potential on the seafloor. Mining inactive SMS deposits may therefore present an extractive opportunity that does not necessitate the disturbance or destruction of active vent habitats. However, if mining of SMS deposits is to take place only at inactive vent sites in order to protect active vent ecosystems, a clear definition of what defines a site as active or inactive is necessary. ACTIVE AND INACTIVE SEAFLOOR MASSIVE SULFIDE DEPOSITS Our understanding of the number of inactive deposits, their size and grades, and how they are preserved on the seafloor remains limited, largely due to the challenges associated with finding these deposits. Over 90% of all hydrothermal vent fields discovered so far are hydrothermally-active. Almost all of these sites were discovered through the detection of chemical anomalies associated with active hydrothermal venting via water column surveys. Inactive sites have no associated hydrothermal plume, and thus the well- established plume survey exploration method is not effective. As a result, very few truly inactive sites inactive sites have been discovered. Alternative exploration methods, such as spontaneous potential (SP) surveys, magnetic surveys, and high-resolution mapping are required (Cherkashev et al., 2013; Jamieson et al., 2014; Tivey and Johnson, 2002). As methods for locating inactive deposits continue to develop, our understanding of the distribution and resource potential of these deposits will increase, and the focus of resource exploration will shift from active to inactive vent sites. However, for now, most exploration and deposit development activities remain focused on active vent fields.

Jan 1, 2018

By Raymond A. Binns

Exploration for high-value massive sulfide deposits on the ocean floor typically commences with a search for chimney fields in appropriate geological settings, followed by collection and assaying of standing chimneys. Individual chimney fields are generally too small in aggregate volume to constitute viable resources in their own right. Unless numerous small fields occur in reasonably close proximity, presence of plentiful sub-seafloor mineralization with acceptable metal tenor is the more likely requirement for potential exploitation. Expensive drilling is required to prove up mounds of collapsed chimneys, or dilatory sheets and veins or replacements of massive/semimassive sulfide (?stockworks? or ?manto?-like bodies) in underlying host rock. Where multiple targets have been defined, as many parameters as possible are desirable to help rank them for drilling.

Jan 1, 2011

By Julian Malnic

Various natural, commercial, engineering and operational factors govern the evolution of approaches taken in the exploration for Seafloor Massive Sulphides (SMS) and in delineating the resource. These stages are prerequisites to the proposed mining of SMS deposits. This paper presents and analyses these factors from the view of an SMS exploration company that is pioneering the exploration of this rich alternative source of zinc, copper and gold. Current exploration practices developed by Marine Scientific Research (MSR) workers for SMS deposits are expected to give way to industry-generated methods as the SMS exploration industry gathers momentum. The exploration process falls into three phases that are described below: Prospecting (locating targets), Indicating Resources, and Measuring Mineral Resources Considerable streamlining of the SMS exploration process will accelerate the rate of discovery. The economics of SMS mining are projected to be superior to comparable terrestrial mining operations in both operating cash cost and capital terms.

Jan 1, 2001

By R. C. Newell

The primary objective of this study was to establish the fate and distribution of material rejected during marine aggregate dredging, and the extent to which this is associated with spatial changes in biological community composition. Two actively dredged sites in the southern North Sea (Licence Areas 430 and 106) were selected in order to provide a comparison of impacts between sites subjected to different levels of dredging intensity and of contrasting environmental conditions. Dispersal of material rejected during the dredging process was monitored by means of acoustic doppler current profiling techniques (ADCP). Composition of the substratum and benthic invertebrate assemblages were investigated by the analysis of seabed grab samples. It was found that dredging in both areas had an impact on seabed bathymetry in the form of dredge furrows and also led to a reduction of the coarse gravel-sized components of the worked area. Sand sized particles were shown to increase in the surface deposits of both dredged areas. This is likely to reflect both the removal of coarse particles as cargo and the settlement of finer particles rejected during overboard screening. Dispersion and settlement profiles of material rejected by dredging vessels suggested that the majority of the suspended sediment load resulting from overboard screening settles to the seabed within 500 m. Some evidence of suspended sediment loads above background levels were noted at distances of up to 2 km from the working vessel. Analysis of the particle size composition of the deposits, along the axis of transport of material from the dredged sites, suggested that the impact on the sediment composition outside the boundaries of the dredged sites is dependent on the strength and direction of net sediment flux at the seabed. Benthic invertebrate communities within the dredged zones of both areas were found to differ significantly from communities in nearby undredged deposits. A major suppression of species richness and abundance was noted in the dredged sectors of both sites when compared to control locations. A ?footprint? of potential impact on the benthic fauna was noted in samples taken along the axis of sediment transport at distances of up to 1750m outside the boundaries of Area 430. In contrast, impacts on benthic community structure at Area 106 appeared to be confined to the immediate vicinity of the dredged zone itself. This apparent difference in impacts, beyond the boundaries of the dredged sectors between the two study sites, was thought to be a reflection of the smaller quantities of material rejected at Area 106 and the weak seabed sediment flux which is characteristic of this area. These findings, along with those of numerous dredging impacts studies, were then used to make generalised predictions of macrobenthic community recovery following marine aggregate extraction in a variety of seabed habitats.

Jan 1, 2004