Search Documents

By J. C. Borland, J. H. Rogerson

Jan 1, 1963

By E. F. Johnson, V. O. Naumann, D. P. Bossler

A method is presented for calculating individual gas and oil or water and oil relative permeabilities from data obtained during a gas drive or a waterflood experiment performed on a linear porous body. The method has been tested and found both rapid and reliable for normal-sized core samples. INTRODUCTION Individual oil and gas or oil and water relative permeabilities are required for a number of reservoir engineering applications. Chief among these is the evaluation of oil displacement under conditions where gravitational effects are significant, such as a water drive or crestal gas injection in a steeply dipping oil reservoir. Numerous proposed methods of obtaining relative permeability data on reservoir core samples have been too tedious and time consuming for practical use, or have yielded questionable and sometimes inconsistent results. A method has been developed by which the individual relative permeability curves can be calculated from data collected during a displacement test. The method is based on sound theoretical considerations. Using this method, with a properly designed experimental procedure, relative permeability curves can be obtained using core samples of normal size (i.e., 2 to 3 in. in length and 1 to 2 in. in diameter) within a few days after receipt of the core. In a recent publication D. A. Efros1 describes an approach to the calculation of individual relative permeabilities that is based on the same theoretical considerations. We believe the approach described in the present paper is more adaptable to practical application than the method implied by Efros. In addition, comparisons with independently determined relative permeabilities are furnished to substantiate the reliability of the new method. DERIVATION Previously the theory of Buckley and Leverett as extended by Welge2 as been used to calculate the ratio of relative permeabilities. In the derivation which follows, this theory is further extended to permit calculation of the individual relative permeabilities. The theory assumes two conditions which must be achieved before the method is applicable. They are that the flow velocity be high enough to achieve what has been termed stabilized displacement,3 and that the flow velocity is constant at all cross sections of the linear porous body. In stabilized displacement the flowing pressure gradient is high compared with the capillary pressure difference between the flowing phases. The high pressure drop insures that the portion of the core in which capillary effects predominate will be compressed to a negligibly small fraction of the total pore space. The assumption of constant flow velocity at all

By W. A. Wood, H. M. Bendler

Cylindrical fatigue specimens of OFHC* copper were subjected to alternating torsion while under axial tension. The superimposed tension strongly influenced the fatigue life of the specimens as well as causing characteristic changes in the structure of the fissures that form and develop throughout the life of the specimen. A further effect of the superimposed tension is a continuous extension of the specimen throughout its life in a manner formally similar to creep at elevated temperatures. RECENTLY, studies of the structural changes leading to fracture of metals by fatigue have been made by a technique which reveals, in section, the lattice distortion arising from slip movements inside the metal and the disturbances built up by these slip movements at the metal surface.1'2 According to this approach, fatigue develops as follows: a) fine slip movements concentrate in bands, producing little strain-hardening and thus permitting abnormal totals of plastic strain before fracture and, therefore, abnormal amounts of lattice distortion along each slip band; b) both forward and backward slip movements occur in each band which, according to their distribution across the band, may build up surface disturbances that include sharp notches; c) these notches early in the life of a specimen penetrate the distorted slip zones and transform them into deep, fine fissures; d) the fissures on continued cycling locally saturate the metal and cause local collapse in the form of a microcrack. Thus, the significant consequence of fatigue or cyclic

Jan 1, 1962

Jan 1, 1970

Jan 1, 1969

By Cornelius F. Kelley

DURING the war, events moved with unprecedented rapidity. Situations, industrial, economic and financial, arose over night that stressed to the uttermost the ingenuity and ability of those who dealt with them. It was essentially a time demanding action rapid and concentrated, and not one for discussion, either academic or polemic. As a result, matters of importance were necessarily transacted without the desirable opportunity being afforded of enabling a general understanding to be gained as to the relative merit or demerit involved, and in some instances, legislation essential to enable the consummation of an important matter was passed without attracting the public attention then deeply engrossed in the larger aspects of the situation. The result was that so long as the public mind was occupied, little or no concern was given to questions that ordinarily would have invited immediate attention; and in some instances, only when as an aftermath of war a particular subject has become a matter of discussion, criticism not altogether fair is made without first obtaining accurate knowledge as to the conditions that prevailed, the purpose sought to be accomplished, or the results obtained by the action taken.

Jan 1, 1921

By W. C. Peters, M. W. Pullen, C. A. Bays

During the past three and a half years considerable improvement in the techniques of solution extraction of salt has been made by the use of wells which are cross-connected by hydraulic fracture at the base of the salt. Fracture is initiated by the application of hydraulic pressure. Underreaming and perforating techniques are used to control initiation. The fracture is then extended by continuous pumping until a pressure communication is obtained. Pressure communication is followed by washing-through to obtain a low-pressure connection. Well construction using non-shrinking cements that will bond with the salt and with associated strata is essential to the process. The connecting procedure described permits solution to attack the salt deposit from its base upward, thereby permitting greater recovery, fewer well repairs, better saturation of brine, and overall economy of development and operation. The fracture method of cross-connection requires special pumping of the fluid and is limited by present experience to initial well spacings up to about 1200 feet. The method has been used in bedded salts and is applicable for wells in salt domes. Since spring of 1956, new developnents in salt extraction wells have followed procedures substantially different from those in prior use. Although multiple well systems, connected either by the natural consequence of the solution process or by undercutting under protective pads, have been used previously, the past three and a half years have brought about new designs and new operation procedures based on cross-connection of the wells using hydraulic fracture. To date these techniques have been applied largely in the bedded salt deposits of Michigan, Ontario, Ohio, West Virginia, and New York. To the writers' knowledge they have not been used in salt dome wells. The methods have not yet been in use for a sufficient period to permit any statistical comparison with the older methods. It is evident from experience to date that the methods result in higher recoveries, lower capital and operating costs, better saturation of produced brine, reduced well maintenance and repair, and in considerably fewer production units to insure

Jan 1, 1961

By P. K. Leung, S. R. Allada, P. M. Dranchuk, D. Quon

The alternating direction explicit procedure (ADEP) makes use of the boundary conditions to reduce multi-dimensional problems to a series of one-dimensional problems. The method, previously applied to reservoirs containing only an under-saturated oil, has now been extended to cover the case of natural gas reservoirs. l his involves solving a non-linear partial differential equation, application of the procedure is straightforward and no calcuIational problems were encountered. INTRODUCTION There has been a growing interest in formulating mathematical models of petroleum and natural gas reservoirs — models which permit the engineer to examine and evaluate the physical and economic consequences of various alternative production policies. The tremendous reduction in the cost of solving such models in recent years has made possible their use as an almost routine management tool. This reduction is the result not only of improved computer hardware but also of the development of more efficient mathematical techniques. The present paper is concerned with the application of a recently proposed numerical method (ADEP) to two-dimensional gas reservoirs. STATEMENT OF THE PROBLEM Given a two-dimensional Region R, bounded by a closed Curve C (Fig. 1) such that the behavior on Curve C is known, the differential mass balance for each fluid phase in R, neglecting gravitational effects and assuming Darcy's law for fluid transport, can be written as:

Jan 1, 1967

By W. A. Burns

Vertical flow is an important mechanism in many petroleum reservoirs. Yet no adequate method has heretofore been proposed for determining the in-situ vertical permeability in a reasonable length of time. Core measurements of vertical permeability do not necessarily represent effective in-situ values. Cores may be representative of only localized pockets of high or low permeability, and total reliance on cores might cause one to overlook the presence of vertical fractures altogether. Conventional single-well tests, interference tests, and pulse tests commonly are used to determine horizontal transmissibility, khh/u, but generally are not designed to measure vertical trans-missibility or other groups containing vertical permeability, ku. A new well test described here provides a measure of in-situ vertical permeability as well as the previously measurable horizontal permeability. This "vertical test" determines the vertical diffusivity, kv/gcu, and horizontal transmissibility, khd1/u (where dl is the length of injection or production perforations). The test is basically a short-term interference or pulse test normally lasting less than a day. Conventional down-hole equipment is used between two isolated sets of perforations in the same well, as shown in Fig. 1. A "layer-cake" description of a reservoir can be obtained by running two or more vertical tests in the same well, each over different vertical intervals. Each test can be analyzed for the effective vertical and horizontal properties of the interval tested. In addition, a vertical well test can determine the effective- ness of a shale barrier or tight zone by testing across it. Field use to date of vertical testing has confirmed its utility in reservoir description. Mathematical Basis Interpretation of vertical tests for ku and kh is based on comparison of measured pressure response with computer-generated response. Pressure behavior during a vertical test in a homogeneous, anisotropic, infinite-acting reservoir (infinite in radial extent and bounded in both directions vertically) is given by the diffusion equation for slightly compressible fluids with negligible gravity effects.l A schematic diagram of the problem is presented in Fig. 2, and an analytic solution, based on the image

Jan 1, 1970

[Executive J. V. W. REYNDERS, Chairman WILLIAM H. BASSETT E. DEGOLYER I-I. C. BELLINGER RICHARD PETERS, JR. Finance GEORGE OTIS SMITH, Chairman H. A. GUESS F. JULIUS FOHS Admissions GEORGE D. BARRON, Chairman DAVID LEVINGER P. A. MOSMAN H. K. MASTERS J. A, SINGMASTER Alternates F. G. BREYER C. W. HAMILTON F. E. PIERCE]

Jan 1, 1928

By J. E. Warren, J. H. Hartsock

An asymptotic solution to the equation that describes the flow of a slightly compressible fluid in an infinite porous medium has been used to estimate the interaction between two adjacent wells producing from a common reservoir. A direct method for approximating the interference time defined by Stevens and Thodosl has been suggested. An alternative definition for the time of interference, based on the minimum pressure change in the interference region, has been proposed; also, a direct method of determination has been prescribed. Examples have been employed to illustrate the use of both methods.

By H. C. H. Darley

The principal causes of unstable boreholes* have been known for many years. For example, in a paper published in 1938, Halbouty and Kaldenbachl listed nearly all the classes of troublesome shales that we know today. Much progress has been made since then, but we still have difficulty in identifying the cause of hole problems and consequently in selecting the right technique for combatting them. This subject was discussed at length by Kelly2 in a recent paper and much valuable information was provided. In the Shell Laboratory it was felt that there was a need for a better understanding of the basic mechanisms underlying the various forms of hole instability, and accordingly, a study was undertaken. This entailed reviewing the physics and chemistry of shales, developing tests for characterizing shales, and constructing a model to study borehole stability. Full simulation of underground conditions was not attempted; for example, we used reconstituted shale specimens, and often simple solutions or suspensions rather than practical drilling muds. Such procedures are necessary in order to establish mechanisms, but caution must be exercised in applying the results to the more complex conditions in the field. Part I — Compaction Swelling and Dispersion of Shales Compaction of Sediments Shales are formed by the compaction of sediments. Water is expressed as sediments are buried by subsequent layers, and the degree of compaction is proportional to the depth of burial, provided the water is able to escape easily to permeable formations. The younger sediments, when recovered at the surface, soften and disperse when mixed with water; the older shales have undergone diagenesis (alteration of the clay minerals, secondary cementation, etc.), and remain hard and unaffected by water. In this paper we shall apply the term "shale", as the drilling engineer does, to everything from clays, which are highly reactive to water, to completely lithified materials such as claystones and slates, which are completely inert. However, because these materials behave quite differently when encountered in the drilling well, it is desirable to develop a simple means of characterizing them. The feature that distinguishes the various shales is their dispersibility in water —soft clays disperse readily, harder shales disperse slowly when agitated, the lithified materials will not disperse at all unless milled. In the dispersibility test used in our study, a weighed amount of dry shale particles in the 12-to-100-mesh-size range was placed in a tube filled with distilled water and allowed to soak for 16 hours. The

Jan 1, 1970

By R. D. Pehlke, J. V. Gluck

AS a portion of a general study of liquid-metal thermodynamics, high-temperature galvanic cells were used to study the effect of added dilute solutes on the activity of zinc in dilute solution with molten bismuth in the range 450° to 650°C. 1,2 The cells were of the type The experimental procedures have been described previously.1 In the course of studies conducted in the bismuth-rich corner of the systems Bi-Zn-Au and Bi-Zn-Cu, marked discontinuities were observed in the electromotive force-temperature relations for a number of the experimental compositions. Above the discontinuity temperatures, the relations, which were linear, exhibited slopes similar to the binary alloy of the same mole fraction zinc, as shown in Figs. I and 2. Below the discontinuity temperatures, the slopes were markedly different, but the relations remained linear. In general, as the amount of the third eletnent was increased, the slope of the lower portion of the relations tended to become less positive. The slopes of electromotive force-temperature relations reflect the entropy of mixing of zinc and, therefore, the occurrence of a discontinuity marks the transition between two different equilibrium situations involving the solution of zinc. A number of other investigators3-5 have used such observations to determine liquidus boundaries in binary alloys. Since the upper portions of the ternary electromotive force-temperature relations of this study had the same slopes as the binary alloys, the discontinuities are interpreted as marking the transition between the single-phase liquid region and the underlying two- and three-phase regions. Reference to the Zn-Bi equilibrium diagram6 confirms that the binary alloys were single-phase liquids at the experimental temperatures. Fig. I shows the electromotive force-temperature relations for the alloys containing Bi-Zn-Au and Fig. 2 shows similar relations for the Bi-Zn-Cu alloys. In the lower portion of each figure, the temperature of the discontinuity is plotted vs the mole fraction of the added solute at the various levels of zinc concentra- tion. Cross-plots from these curves at constant temperature permitted the construction of the partial liquidus surface isotherms shown in Figs. 3 and 4.

Jan 1, 1967

By D. R. Parrish, F. F. Craig

In some respects, forward combustion (alias: fie-flooding, underground combustion, in-situ combustion, dry combustion) is an efficient oil recovery method. For example, its displacement efficiency (as much as 95 percent in reservoirs with high porosity and high oil saturation) is good. In its use of heat, however, forward combustion is grossly inefficient. Most of the heat generated during forward combustion is wasted. About one-fifth of the heat is picked up by the incoming air and re-used (regenerated); the remainder is left behind the combustion zone and ultimately is lost. Compressed air is expensive, and heat generated from compressed air via underground combustion is too valuable to be thrown away. Improvement is needed. Since the early 1950's, improvements in forward combustion by addition of water injection have been discussed, particularly in the patent literature, with increasing frequency.'-'' These concepts are based on the fact that relatively inexpensive water can be used to pick up much of the heat that is ordinarily wasted during forward combustion, and transport it forward to a more useful place, thereby reducing the amount of air required to move a heat front through the reservoir. Several approaches have been proposed. Merriam and Squires1 taught that a combustible (fuel) gas should be injected along with the air and water. This, however, would give at least a tendency toward reverse combustion instead of forward combustion, and would reduce the velocity of the heat bank, defeating the primary purpose of the water injection. Pelzer2 described primarily a batchwise method of forward combustion and water flooding. He advocated burning part way through a reservoir with forward combustion, then switching from air to water injection alone to push the heat toward the producing wells. Though possible, this method has serious disadvantages, the major one being that, by the time water injection is started, much of the heat has been irretrievably lost to the overlying and underlying formations. We have described what is considered a practical Combination Of Forward Combustion And Water-flooding (COFCAW).3,4 Air and water are injected simultaneously (or alternately) after a small heat bank has been formed by forward combustion. Some of the injected fluid fills up the region behind the heat bank; the rest enters the heat bank. Upon encountering heated rock, the water is converted into steam, which then flows ahead of the combustion zone and displaces much of the oil in place. Only enough air is injected to provide heat for vaporization of the water and to compensate for reservoir heat losses. Since the size of the heat bank is minimized, heat losses also are minimized. Because of more efficient oil displacement ahead of the combustion zone, fuel consumption is reduced. Too, unlike a forward combustion zone that cannot move until all fuel at a point has been consumed, COFCAW leaves some

Jan 1, 1970

By Robert Bakish, William D. Robertson

AFTER more than fifty years of investigation and continuing failure in service, a satisfactory mechanism to explain stress corrosion cracking in homogeneous alloys is still lacking. The relative chemical activity of grain boundaries and adjacent grains, inferred from the boundary structure, has been used to explain intergranular cracking in a brass.' This concept is probably correct as a general hypothesis, but it requires much more extensive development in order to explain satisfactorily the observed phenomena. For example, the specific function of the solute in an alloy must be considered, because intergranular failure does not occur in pure metals,' which are structurally similar to homogeneous alloys. Also, in this connection, an inter crystalline fracture path in binary copper alloys can be changed to a transcrystalline path by relatively small ternary additions.' The fracture path in ß brass is predominantly transcrystalline,' in contrast with an inter crystalline path in a brass. Whether the two different fracture paths are the result of a difference in composition, crystal structure, or the state of long range order is unknown and cannot be determined with ß brass, because only the ordered state can be obtained at room temperature. The study of chemical activity at structural sites in the Cu-Zn system is restricted by the formation of opaque films in an ammonia environment in which stress corrosion cracking is generally observed. Furthermore, both components of the alloy are chemically active and the interpretation of observations is therefore relatively complicated. The Cu-Au system is a better choice for the purpose of studying structural factors. In particular, CuAu is very susceptible to cracking in ferric chloride and opaque films are not formed in this solution; it may be obtained in different states of long and short range order; and, finally, only copper is oxidized in dilute ferric chloride, which considerably simplifies the chemical problem. To provide information necessary for a more general explanation of stress corrosion cracking in homogeneous solid solutions, the following structural factors have been investigated in a Cu-Au alloy having a composition corresponding to Cu,Au: 1) the effect of long and short range order; 2) the structural sites from which copper is removed from the annealed and cold worked polycrystalline alloy; and 3) the effect of annealing time and temperature on structural reactions in the cold worked alloy. Experimental Procedure A Cu-Au alloy of nominal Cu3Au composition was cast from cathode copper and high purity gold and fabricated into sheet and wire. Chemical analysis for copper and gold indicated 48.92 wt pct Cu and 51.01 pct Au. Quantitative spectrographic analysis indicated 0.01 pct Ag, 0.002 pct Pd, 0.001 pct Pb, and 0.002 pct Fe, with traces of magnesium, silicon, and zinc. Presumably most of the remaining 0.055 pct corresponds to the limits of analytical precision. Heat treatments of wire and sheet were conducted in argon or vacuum. Wire specimens, 0.064 in. diam, were heated for 1 hr at 850 °C to establish a definite

Jan 1, 1957

By James K. Richardson

STATISTICAL evidence shows that continued efforts made by Government and industry to make mining safer during the last two decades have had most favorable results. In the copper-mining industry an accident frequency of 146 per million man-hours worked in 1925 dropped 71 per cent by 1945 to 43. This downward trend was relatively consistent except for a high period in 1937 which was probably due to a resumption of large-scale operation with many untrained miners. The iron-mining industry showed a similar trend, but at the relatively lower accident frequency of 66, which dropped to 24 in 1945. The close relationship between the steel and iron-mining industries may be one reason for the lower accident frequencies, because the steel industry is noted for its greater recognition of the fact that safe working conditions are an important part of labor-management relations.

Jan 1, 1948

By O. E. Palasvirta

Several drum-type, low-intensity dry magnetic separators have recently been described 1,2,3,4 all of which share at least two generic similarities. The magnet consists of a multiplicity of poles of alternating polarity and, the speed of the drum shell, relatiw to the magnet, is such that the magnetics are agitated through rotation of the magnetic particles around their individual axes. The speed of the drum relative to the magnet (differential speed) determines the frequency of the field reversals. For effective agitation this frequency generally has to be above a specific value, which varies according to the mean particle size of the magnetics. With separators of small diameter, say less than 11/2 ft., a sufficient differential speed for treatment of fine magnetite can be attained only by rotating both the magnet and the drum separately; separators of large diameter may attain sufficiently high differential speeds with stationary magnets. Separators of large diameter thus have the advantage of simplicity of design. The capacity of a separator of this type is directly proportional to the speed of the shell. As the centrifugal force opposing the magnetic force increases at a slower rate than the peripheral speed of the shell when drum diameter is increased, large drums can be operated with higher peripheral speeds. Thus they have a higher capacity than smaller drums. Separation is also a statistical phenomenon, i.e. the grade of concentrate improves as the number of agitations or rotations of the magnetic particles per separation increases. As separators of large diameter have space for a large number of magnets they are best suited for production of optimum grade concentrate. The statements above are general clues For separator design. In the following an expression IS derived showing a more exact relationship between the pertinent separator variables. As both magnetic attraction and centrifugal forces are directly proportional to the volume of the affected bodies, complications in mathematical analysis, arising from variable particle size, are avoided by considering the force per unit volume of affected material. For the magnetic force per unit volume Runolinna (3) gives the following equation: V " 1 + N(ur, - 1) uo dr (1) where ur and uo stand for the relative permeability and the permeability of vacuum, respectively, N is the demagnetization factor, B the intensity of the magnetic field, and r the distance from the face of the magnetic pole. The permeability of a specific magnetite ore can generally be considered as a constant. For ground, liberated material N can also be treated as a constant, and the first simplification can be made by writing ur-1 1=k1. 1 + N(ur - 1) uD k1. Fig. 1 shows the field intensity curves for two U-magnets of different size, but of roughly similar geometry of cross-section as plotted against the distance from the plane of the pole faces. The curves

Jan 1, 1961

The following record of the important responsibilities already shouldered by Dr. Ricketts will give some indication of the trust and confidence reposed in him by his colleagues. The Institute is to be congratulated that a man who is already so much engaged should be willing to assume the further responsibility of guiding the Institute's Ship of state during the ensuing year. Louis Davidson Ricketts, who is brother of Professor Palmer or Chamberlaine Ricketts, President of Rensselaer Polytechnic Institute, was born at Elkton, Md., Dec. 19. 1859, was graduated from Princeton University in 1881 with the degree, Bachelor of Science, chosen a Fellow in Chemistry and W. S. Ward Fellow in Economic Geology, and after two years' study given the degree Doctor of Science. Following the completion of Iris work at Princeton, Dr. Ricketts went to Colorado and started to work as a mine surveyor. For the 15 years following, his time was chiefly occupied in reconnaissance work, geological work and mine examination. From 1887 to 1890 Dr. Ricketts was Geologist for Wyoming, and at, the end of that period transferred his operations to the Southwest. where he has since been steadily engaged in large mining projects. He was identified with the acquisition of the property now owned by the Moctezuma Copper Co., a , subsidiary of Phelps, Dodge & Co., at Nacozari, Sonora, Mex. From 1899 to 1901 he was General Manager of the property and during his administration the concentrator and reduction works were completed and the mines put on a dividend-paying basis

Jan 3, 1916

By J. F. Shea, O. F. Tangel

Battelle Memorial Institute participated in a program for the General Services Administration aimed at developing a nickel-cobalt separation process that could be integrated in the Nicaro nickel plant. At the time the programwas being carried out, the Nicaro process was a straight-through operation, in which the ore was reduced and leached, after which the pregnant solution was boiled to produce a so-called "bulk precipitate" which contained virtually all of the nickel and cobalt which had been dissolved in the leaching step. The weight ratio of nickel to cobalt in Nicaro ore is approximately 15 to 20:l. The weight ratio of nickel to cobalt in the finished product had to be 100:l or higher to meet specifications. Because the Nicaro process embodied no nickel-cobalt separation step, the only way that a bulk precipitate of the specified nicke1:cobalt ratio could be produced was to so adjust roasting and leaching conditions that nickel would be selectively leached and most of the cobalt would be rejected with the tailings. The required selectivity, however, was achieved at the expense of nickel recovery, which was 5 or more per cent less than might have been obtained with the existing equipment, utilities, man power, etc., had selectivity been no object. The over-all purpose of the program was to develop a separation step that could be fitted into or onto the Nicaro facilities and which would permit the manufacture of a product that would meet the desired specifications and still permit the recovery of a maximum amount of nickel. Battelle suggested that this might be accomplished by reprocessing off-specification bulk precipitate and specifically suggested the process based on ammonium sulphate leaching followed by hydrogen reduction of the leach solution according to techniques developed commercially by Sherritt Gordon Mines Limited. Such a process would not only satisfy the objectives of the research but would present two additional advantages. (1) It would produce a separate cobalt product which could be further processed into metal, alloys, oxides, or salts. (2) It would yield nickel in metallic form which might be more generally marketable and command a slightly higher price per unit of nickel than the Nicaro oxide product. DESCRIPTION OF THE PROCESS Figure 1 is a flowsheet of the process. The essential features are: (1) Extraction of about 97 per cent of the nickel and about 85 per cent of the cobalt from bulk precipitate by a principal leach with ainmonium sulphate solution (Step A). Extraction of virtually all of

Jan 1, 1961

By A. E. Anderson, H. J. Hilll

Laboratory data for 155 field muds and 77 .shales have been used to develop correlations to estimate the net streaming potential component of the SP. Analysis of these data and comparison with field tests show that streaming potential corrections must be made to obtain an accurate estimate of the electrochemical potential for use in the determinntion of formation water resi-iiviy. The self-potential curve is related to formation water resistivity, and considerable effort within the oil industry has been directed toward clarifying this relationship. The Schlumbergers and Leonardon1,2 recognized that two types of potentials, electrochemical and electro-kinetic, resulted in the net potential variation in the borehole. Most of the later papers have dealt with the electrochemical component and its controlling parameters. The investigations of Wyllie,2" Salisch' and Moore5 provide the most extensive sources of data on streaming potentials across mud cakes. These authors observed streaming potentials of sufficient magnitude to be of critical importance in SP interpretation, if it is assumed that streaming potentials develop only opposite permeable beds. Streaming potentials across shales have been reported by Schenck and by Gondouin, et al.7 Since SP magnitude is the difference in potential opposite shale and sand beds, these authors suggested that the net streaming potential component may be negligible. The present investigation was initiated to evaluate empirically some of the parameters controlling the magnitude of the net borehole streaming potential and to determine whether useful relations between mud properties and net streaming potential could be established. Field muds were used in this investigation. These muds were characterized by the amount and type of chemical treatment utilized for five days before Sampling. Filter loss, mud resistivity, mud density and filtrate resistivity were determined for each mud with conventional methods and apparatus. Mud filtrate pH was estimated with Hydrion pH paper for the appropriate range. Streaming PotentIals Across MuD Cakes Commercial calomel-saturated KC1 electrodes are subject to potential changes attributed to contamination of the very small fiber-tip bridge by particles of clay from the drilling mud.3 To minimize this difficulty, a large diameter bridge (Fig. 1) was constructed with saturated KC1-agar gel and a filter disc of microporous porcelain. Experiments showed that streaming potentials across this bridge are less than 0.2 mv at pressure dif-