Search Documents

By S. Akhtar

Interstitial compounds of iron, cobalt, and nickel, and their binary and ternary mixtures with silver, gold, palladium, and platinum were prepared and tested as fuel cell catalysts. The first step in the preparation of the interstitial compounds consisted of preparing finely divided metals. This was done either by the Raney method or by reduction of precipitated hydroxides of the metals. The finely divided reduced metals were then treated with carbon-and/or nitrogen-containing gases to prepare their carbides, nitrides, and nitrocarbides. The materials were tested for cathodic activity towards O2 and for anodic activity towards H2, C3H8, NH3, CO, and N2H4 in acid and alkaline electrolytes at 25° to 90° C in half-cell assemblies. Samples of carbided and nitrocarbided INi-lAg-1Au were about one fifth as active as Pt-black in the reduction of O2 in 35 percent KOH solution, whereas the activities of several interstitial preparations exceeded the activity of Pt-black in the reduction of O2 in 12M KOH containing N2H4. Nitrocarbides of x-Fe2C, 3Ni-1Au, and 1Ni-3Au were effective catalysts for oxidizing N2H4 in liquid NH3 containing NH4SCN. Corrosion of the catalysts by electrolytes was severe in many cases.

Jan 1, 1970

By S. L. Weber, D. E. Banks

"Silicosis was first reported by the ancient Greeks and is apparently as old as human history. The prevalence of this illness peaked in the last half of the 19th century and the early part of this century, when mechanized industry was developing and the relationship between dust exposure and disease was less well understood. Yet, even today in devel-oped countries, sporadic outbreaks of silicosis occur when workers are consistently exposed to silica particles of respir-able size (0.5 to 5.0 µm in diameter) at levels exceeding those recognized to be safe.Silicon dioxide or silica. is the earth's most abundant mineral. Silica is considered to be either free (i.e.. unbound to other minerals) or combined. Minerals with high amounts of free silica include quartz (including granite) flint. Chert, opal, chalcedony, and diatomite. Combined forms of silica are called silicates and include, among others, asbestos talc and kaolin.In the crystalline form, silica exists as quartz, cristobalite, and tridymite (Fig. 28). Of these quartz is ubiquitous in the environment and occurs as sand and as a part of many rocks. Cristobalite and tridymite occur naturally in lava and can be formed by the heating of quartz or amorphous silica. Cristo-balite is more tibrogenic than quartz. Amorphous silica is noncrystalline and, therefore, is relatively nontoxic and does not cause silicosis. It occurs as diatomite (skeletons of pre-historic marine organisms) or as vitreous silica (glass), the result of carefully melting and then quickly cooling free crystalline silica. Heating diatomite with or without alkali (a process known as calcining), forms cristobalite and adds the respiratory toxicity of free crystalline silica.There are many opportunities for occupational exposure to respirable crystalline free silica. Some of the commonly en-countered occupations in which the risk of silicosis exists are reported in Table 20.Silicosis. the pulmonary disease caused by the inhalation of silica particles of respirable size, is most commonly cate-gorized by findings on the chest radiograph. The most typical presentations simple silicosis and progressive massive fibrosis appear different radiologically but are grouped under the category of classic silicosis because they are a part of the radiographic spectrum of this illness. Radiographically, simple silicosis appears as small (less than 10 mm in diameter), rounded opacities, typically predominant in the upper lung zones. Progressive massive fibrosis is the result of the coalescence of these small nodular opacities and appears as larger opacities (more than 10 mm in diameter), again typicallydistributed in the upper lung zones."

Dec 1, 1995

By John G. Parker

The rare-earth elements, sometimes known as the lanthanides, comprise the series of 15 chemically similar elements with atomic numbers 57 through 71. Yttrium, with atomic number 39, is often included in the group, because its properties are similar and it more often than not occurs in association with the lanthanides. Thorium is included in this survey due to its close association with the lanthanides, particularly in the mineral monazite. The lanthanides were first recognized as elements around 1750 and were the subject of much study by chemists during the 19th century. The purely chemical methods then available failed to resolve the strange intimate relationships between these elements, and it was not until about 1920 that the full series was explained.

Jan 1, 1971

By Barton J. Suchomel

Introduction Despite perennial economic turbulence, Argentina continues to push ahead with efforts to develop its fledgling hardrock mining industry. The country lacks the infrastructure and mining history of neighboring Chile, but contains vast areas of great resource potential. The eastern slope of the Andean Cordillera in west-northwest Argentina is a relatively little-explored region offering geology highly conducive to the occurrence of base and precious metals deposits. Past exploration has concentrated on locating and evaluating porphyry copper-molybdenum (Cu-Mo) type occurrences. Comparatively little attention has been given to precious metals potential. An interesting and important group of base and precious metals prospects in northwestern Argentina occurs within and adjacent to the Upper Miocene Farallon Negro volcanic complex in Catamarca province. The volcanic complex contains numerous base and precious metals vein occurrences, high gold porphyry copper prospects, and possible disseminated gold targets that have attracted relatively minor attention in the past. Various geologic aspects of the region have been reported by several workers (Llambias, 1970, 1972; Caelles et al, 1971; and Sillitoe, 1973). Regional geology The Farallon Negro volcanic complex is located within the Sierras Pampeanas morphostructural province about 200 km (125 miles) east of the main Andean Cordillera (Fig. 1). The Sierras Pampeanas is characterized by north-south-trending basin and range topography that developed during the Miocene and Pliocene. Uplifted blocks are composed mainly of lower Paleozoic metasediments and granitoid plutonic rocks unconformably overlain by Tertiary redbeds and minor carbonates. A consistent landward migration of volcanic and intrusive ac¬tivity occurred in this region of the Andes from the early Mesozoic through the mid-Tertiary. An eastward extension of magmatism during the Miocene and Pliocene resulted in the formation of the Farallon Negro volcanic center. Volcanism at Farallon Negro ini-

Jan 8, 1988

By David Newman

Multiple seam underground coal mining is ubiquitous in Appalachia. Many coal properties have from two to ten or more economically mineable coal seams. Because of the ability to penetrate 600-feet to 1,000-feet or deeper into the mountainside leaving panels of web pillars separated by barrier pillars, highwall mining is a hybrid between surface and underground mining. As a result, many of the ground control problems commonly associated with multiple seam underground mining exist with multiple seam highwall mining. These include: i) superjacent mines, subsidence and caving propagating to overlying seams and ii) mines, pooled water and the potential for inundation resulting from a iii) breakthrough between an active highwall mine and abandoned underground mines in the same or superjacent seams, the presence of overlying or underlying mine workings where iv) pillar columnization in the active mine is not possible, and v) the question of whether to mine ?top-down? or ?bottom-up.? Case histories are presented from southeast Ohio where the Middle Kittanning No. 6 and Lower Kittanning No. 5 seams are successfully highwall mined with 20-feet to 40-feet of largely shale interburden. A highwall miner was caught in a highwall collapse in the Middle Kittanning No. 6 seam when it was overmining auger workings in the Lower Kittanning No. 5 seam. Multiple seam interaction caused by the overmining transferred overburden stress onto the Lower Kittanning No. 5 seam. The overburden concentrated through web pillars initiated auger web pillar failure, resulting in roof collapse and subsidence in the Lower Kittanning No. 5 seam that propagated up to the Middle Kittanning No. 6 seam. A second case history involves multiple seam highwall mining in southeast Kentucky. The A3 Rider, A3, B2, and C1 seams are being highwall mined around abandoned underground mines in the A3 and B2 seams and augering in the A3 Rider. Because of spoil storage constraints for the surface contour mines, the highwall miner follows the active pits in each seam so a standard sequence of ?top-down? or ?bottom-up mining does not exist. The planning and engineering design considerations associated with each case history is presented along with geotechnical information. In the case of the highwall collapse a back analysis is presented of the stability and safety factors for the auger webs, highwall miner web pillars, and barrier pillars.

Jan 1, 2009

By H. Foster Bain

THERE has never been a great civilized nation which did not have a mining industry; civilization cannot flourish without metal mining. Without tools we can have none of the 'industries that are the foundation of civilization and without metal mining we cannot produce the material of which tools are made. Therefore, if we have no metal mining we have no metals, no tools, no civilization. An example to illustrate this may be drawn from a recent article in the Saturday Evening Post which described the run-down condition of modern Athens. Athens is nothing but a busted mining camp! In its palmy days the Greeks so applied the leasing system to the silver mines of Laurium that the royalties, paid the expenses of government and instead of a tax bill the inhabitants received a pay check. The Persians came over to capture these mines but the Greek navy was built to defend them. When the silver mines played out, Greek civilization declined.. Our mining must continue if our civilization is to continue.

Jan 1, 1921

By Joseph C. Gillen

This paper discusses the design, construction, and performance of the support of excavation system used at The Atlantic Building jobsite. The support of excavation system had to be adaptable to the different conditions surrounding the site. These conditions included support of four historic building façades, including the nine-story Atlantic Building, as well as support of three historic row-houses along two walls. Directly adjacent to the site is the historic Ford?s Theatre and townhouse. Across a 15? alley is the American Immigration Lawyers Association (AILA) Building, and across a 30? alley is the Federal Election Commission Building and another ongoing excavation. Of historical note, these two alleys were the escape route for John Wilkes Booth following his assassination of President Lincoln. With the excavation being 53? to 58? deep, the system included driven and drilled soldier piles, drilled bracket piles, and two modified tangent walls. The bracing included tiebacks, corner braces, wales, cross lot struts, and a specially designed support system for the nine-story façade. The footprint of the excavation included 12 corners and all alleys and streets were to remain open during construction. The performance requirements for system movement at Ford?s Theatre and AILA Building were ½ inches in the horizontal direction. The modified tangent walls were used in these areas to provide stiffness. The soil conditions at the site were fill material on top of a shallow, sandy, silty, gravel layer on top of a deep layer of soft organic silt and clay. Below the silt and clay layer was fine sandy material at the subgrade.

Jan 1, 2006

By J. J. Gilman

The dependence of ortho kink-band formation on crystal orientation, on temperature, and on the conditions at the ends of a specimen is described. Load-compression curves for crystals that kink are presented. The reversibility of ortho kinking is demonstrated, and motion of kink planes through crystals is shown. Finally, a phenomenological explanation of ortho kink-band formation is given. ORTHO compressive kink bands (Fig. la) were discovered for the case of metals by Orowan,1 and they have been discussed by Jillson2 and in some detail by Hess and Barrett." However, their history in nonmetallic crystals is considerably older. It is not known when they were first observed in mineral crystals, but descriptions of them may be found as early as 1885.* They were sometimes mistaken for twins.6 Mügge seems to have been first to realize their true nature and importance. He reviewed the knowledge of them for a wide variety of crystals: anhydrite, antimonite, kyanite, vivianite, gypsum, mica, graphite, molybdenite, barium bromide, cal-cite, sodium nitrate, and barite. Also, the "twins" observed by Bridgman7 in sapphire crystals resemble kink bands more than twins. The terms ortho and para kink bands have been coined in order to distinguish between two types of kink bands which seem to represent the same geometrical configurations, but which have different origins and sizes. Ortho kink bands are the usual type that form at low loads when zinc crystals are compressed parallel to the basal plane. Para kink bands form at much higher loads in highly deformed crystals. These terms refer to compression phenomena and are not to be confused with analogous tension phenomena such as tensile kink bands and deformation bands. Mügge described the geometry of ortho kink bands quite completely for kyanite crystals, Fig. lc. The geometry observed for cadmium by Orowan1 and for zinc by Hess and Barrett3 is very similar to that described by Mügge. (See Hess and Barrett for a complete discussion.) Mügge associated kinking with bending combined with basal slip. He pointed out that the kink angles

Jan 1, 1955

By S. J. Hussey

This Bureau of Mines report presents a discussion of the statistical approach to the design of experiments and indicates, by concrete examples, how and when statistical design is essential for obtaining meaningful data with a minimum number of experiments. Every research worker plans his work and designs his experiments in a manner which, based on his experience, seems most rational to him and which he believes will produce the information essential for resolving the problems. If the results obtained are open to multiple interpretations and are not of definitive reliability, the failure of the experiment design to produce the desired information may be due to several causes, These include faulty judgment in selecting the factors to be tested, ignoring the importance of interaction between factors, failure to adequately control test variables, and assuming that meaningful trends in the results can be identified without comparison to a predetermined experimental error. An experienced researcher probably will deduce from the nature of the data obtained that the design is faulty and may by trial and error ultimately arrive at the correct solution to the problem. Statistical methods of planning research minimize the chance of faulty experiment design, embody concrete procedures for testing the validity and reliability of the test data and for indicating mandatory changes in the design, and enable the researcher to obtain meaningful information with the least number of tests.

Jan 1, 1963

By Ryan C. Linthicum

A system of steel sheeting and multiple levels of high capacity double corrosion protected soil anchors were used to restrain a major slope failure that occurred at the base of the Watchung Mountains mid-way through construction of a 650,000 SF retail center along Route 22 in Watchung, New Jersey. The implementation of a design-build earth retaining structure was necessary to stabilize and repair the disturbed mountainside in a timely fashion to permit completion of the retail center on a fast track schedule. The tied back steel sheetpile wall was approximately 2,000 feet long and varied in height from 12 to 25 feet. The hillside extended approximately 350 feet above and 600 feet beyond the wall with the main failure scarp extending 50 feet above and 90 feet beyond. The wall was constructed in a top-down manner and required the installation of 475 anchors to resist loads of up to 70 kips/ft produced by the creeping hillside and groundwater flows from both a series of springs and steady state seepage through an inclined zone of fine sand. Incorporation of a unique tie point connection eliminated the need for a waler, facilitating and simplifying modifications to anchor locations based on anchor load test results and conditions encountered during construction. Post grouting also proved to be an essential element in the successful construction. This paper presents the design and the construction methods used to restrain the significant earth lateral loads produced by a slope failure using steel sheeting tied back with high capacity soil anchors with anchor loads distributed to the sheeting through a unique tie point connection on a fast track schedule. Installation techniques, testing programs, and construction quality control are also discussed.

Jan 1, 2003

By M Begbie, R J. Norris, D J. MacKenzie

The Otago Schist is crossed by numerous deformation zones that formed in the latter stages of metamorphism and uplift of the metamorphic belt. These deformation zones are long (tens of km) linear features at the regional scale, and are generally narrow (km scale or less). Many of these structural zones separate schist domains with different rock types and structural/metamorphic histories. The Hyde-Macraes Shear Zone is one such deformation zone, and this zone hosts the active Macraes gold mine. The Rise & Shine Shear Zone, 80 km NW of Macraes, is also enriched in gold and has been mined historically. Mineralisation in both these shear zones occurred during the transition from ductile to brittle deformation as the schist belt was uplifted from greenschist facies metamorphic conditions. Recrystallisation of quartz and micas in the early stages was overprinted by cataclasis, with sulfide and gold precipitation throughout. Many of the other late metamorphic deformation zones formed under similar greenschist to sub-greenschist facies conditions, with similar overprinting of recrystallisation textures and folds by more brittle textures such as breccias. Under these conditions, originally regionally pervasive deformation at the highest metamorphic grades was evolving towards more focussed high strain zones at lower temperatures and pressures. Shear zones initially focussed fluid flow along microshears and mineral grain boundaries, resulting in 1 to 100 m scale alteration and replacement in the host schist, with only local development of quartz veins. Fluid flow was not controlled by open fractures, and the rate of fluid movement was probably slow and pervasive. After uplift into the brittle regime, the schist belt underwent tectonic extension. Extension was accompanied by development of swarms of steeply dipping veins, with localised mineralised normal faults. Hydrothermal fluid flow throughout this uplift history was a normal consequence of late stage devolatilisation of the metamorphic belt. Hence, all late metamorphic deformation zones should be considered prospective for gold accumulation.

Jan 1, 2005

By D. A. Donato

It is often necessary for a mining company to extract coal from a seam underlying a previously mined coal seam. The impact of the overlying mine workings on the stress distribution within the underlying mine workings is very difficult to assess without the use of numerical modeling techniques. This paper demonstrates the usefulness of applying numerical modeling to evaluate alternate startup-room locations for a longwall panel considering the effects of multiple seam interaction. MULSIMIPC, a code adapted by the former U. S. Bureau of Mines, was used to compare stress patterns in two proposed startup-room locations. These model results were not only compared to each other, but also to results from a model with no overlying mine workings to provide baseline criteria for evaluation of the two proposed startup-room locations. The numerical modeling study was successful in providing useful information to the coal company and the regulatory agency (MSHA), resulting in a mine design that was both safe and efficient, and prevented the sterilization of a large volume of coal reserves.

Jan 1, 1996

By Hugo Julien

According to OSHA 29 CFR Part 1910.119 (Process safety management of highly hazardous chemicals), Canadian Provincial Safety Standard Acts or Federal laws, the owner of stationary equipment (Boilers, stacks, piping, pressure vessel, etc.) should follow a complete inspection plan and follow an Integrity Operating Windows (IOW’s) adapted for each of them. Some important variables shall be included in the inspection plan such as specific damage mechanisms versus alloy used in the original design, process conditions, etc. Some North American’s standards exist, like the one listed in ASME PTB-2-2009, to help owner to create such inspection program. The new API RP 584, Integrity Operating Windows (IOW’s) can guide Mining & Metals owners to find out their specific IOW’s. Inspection frequencies are often described in the Jurisdiction Safety Acts such as the British Columbia B.C. Reg. 104/2004, etc. but often left in the owner representative responsibility (Bill C-21, federal Act to amend the Canadian Human Rights Act). Every deficiency should be repaired according to recognized Codes such as ASME PCC-2, etc.. If flaws not conforming to the original Code of construction are found, this article will introduce the Fitness-For- Service assessment principles to be able to accept it without any repairs.

Jan 1, 2014

By Henry S. Washington

I. INTRODUCTION. DURING the last twenty years or so the chemical investigation of rocks has made great advances, and it is now generally recognized that a knowledge of the chemical composition is as essential as that of the texture or mineral composition-if not more so-for the proper classification of rocks and study of their origin and relationships. Rock-analyses have vastly increased in numbers and, what is of greater importance, in quality. New and improved methods permit of greater accuracy than was possible in the early days, and the list of chemical constituents frequently determined has risen from the seven or eight of the greater part of the nineteenth century to twenty or more. Indeed, rock-analyses with determinations of so many constituents are now commonly made by the chemists of the United States and Australia, while in Germany, Great Britain, France, and Italy the rarer constituents are determined more frequently than formerly. As a consequence of this modern, accurate work, it has been discovered that some elements which were formerly supposed to be rare are of wide-spread occurrence and are often present in considerable amount. The fact is further being developed that the elements tend to show certain relations of occurrence or abundance in connection with each other. This is a fact which is applicable to the rarer elements, and which also finds a broad geological and petrological expression in the recognition of petrographic provinces. We are beginning to obtain some definite, though as yet rudimentary, knowledge of the distribution of the elements among igneous rocks. Some of the results along these lines obtained by study of the vast accumulation of analytical data now available are well known to petrologists, while others do not seem to be so gener-

Sep 1, 1908

By Victor Raul Alarcon

The Ilo Refinery was commissioned in 1975, with a cathode production capacity of 150,000 tpy. In 1994, Southern Perú Copper Corporation (SPCC) purchased the Refinery from Minero Perú SA. Subsequently, in November 1999, Grupo Mexico acquired control of Southern Perú. The anode production facility is located at the Ilo Refinery. A number of effective operating and quality control practices have been developed that have improved anode quality, as well as increasing anode production capacity to 350,000 tpy. These, and other optimization actions have allowed for a current density increase from 213 A/m2 to 275 A/m2, while maintaining current efficiency at 98% and sustaining the high quality of the cathode. The paper will outline the scope of operational practices in the Anode Plant and provide some discussion on the Ilo Smelter modernization project, and the resulting impact on the existing anode plant.

Jan 1, 2005

Filtration of pulps of varying densities is an essential operation in the hydro-metallurgical production of zinc. The use of filters naturally applies only to the "wet" plants, and in these varying types and sizes are in commission. At Risdon, the Moore suction filter is used for the heavier pulps, except in one instance, where a modification of the Butters-Cassell filter is installed.Filter presses are in general use, and of these, one is a washing unit; the plates, and frames are of cast iron or mild steel, except in one case which is a centre feed press having wooden frames.FILTER DESIGNThe problem of filtration presented itself very early in the history of Risdon and the first developments occurred in what was termed the 250 -lb. plant. Here experiments were made with many types of filters, and as this was the pilot plant on which the design of the 10 ton plant (10 tons of zinc per day) was based, quick decisions were necessary.An Oliver type filter was chosen for the heavier pulp or residue, and a Shriver wooden frame filter press for the lighter pulps.To this day, but with a number of variations, filter presses continue to function unopposed in their particular field; however, the Oliver filter was soon superseded because it was found impossible to wash the filter cake efficiently without repulping; consequently its use was abandoned and the Moore filter adopted.Both- these filters have been modified and developed in many ways to meet the requirements of a zinc plant, but they retain their original basic features.

Jan 1, 1949

By R. J. Balfour, T. L. Papucciyan

"INTRODUCTIONCapital Cost considerations are basic to feasibility in the achievement of success for Mineral Processing Projects as much as or more than in many other industries. Capital cost is an important factor ae it 1R the unit of measurement for process engineering economic decisions. As a result of ever increasing complexity, alternatives of process and remoteness of site, there is an ever increasing emphasis on accurate estimating and the attendant cost control systems in the international market of today for the Mineral Industry where initial plant costs are becoming a more important factor than operating costs. An undervaluation means trouble ahead. An over-cautious assessment may bring an unnecessary abandonment of a project. Consequently, the ultimate cost must be predicted early and accurately and must be controlled to this parameter during the design and construction phases. Cost Est!~ mating is one of a variety of project management tools used to assist in planning and achieving the optimum balance between Quality, Cost and Time, the eternal triangle of evaluation, namely obtaining a project of acceptable quality at minimum cost and on time. In order to attain these established objectives, proper planning, organizing, coordinating, monitoring, adjusting and controlling the design, procurement and construction elements of the project are essential.This project management approach based upon the principle of a Task Force under single management, comprising a complete service organization, requires a substantial number of qualified individuals specialized in their own field and capable of working together as a team to perform their various functions effectively. The Task Force is supported by their chiefs of discipline and performs in accordance with established procedures and standards under the leadership of a Project Manager.General Engineering Company Limited with the backing of the full resources of Surveyer, Nenniger & Chenevert and its total staff of approximately 1,0009 offers the complete project management service to the Mineral Processing Industry of North America and the rest of the world. As mine sites become more remote and difficult of access, the need for an experienced team of specialists who work under the Task Force principle, with well established standards and procedures becomes even more important. Our long history of successful pro1ecta in this field has been our training ground for the fulfillment of this need."

Jan 1, 1972

The revised estimate of coal production in January 1977, is 39 million tons -- down 12 mi 11 ion tons compared with production in January of last year, largely as a consequence of the snow storms and cold. The major coal-hauling railroads operating in Eastern and Midwestern States reported to the Bureau of Mines that they loaded approximately the same number of cars for the week ended February 5, as in the preceding week. The Bureau of Mines estimates that U.S. coal production for the week ending February 5, 1977, was approximately 8.5 million tons, or nearly 3.5 million tons less than production for the corresponding week in 1976. Coal production from January 1 - February 5, 1977, was approximately 47.8 mi 11 ion tons compared with production of 63.5 million tons for the corresponding period in 1976. As of the first week in February, river and truck shipments of coal in the Eastern U.S. were about one-half of the normal traffic. Despite the freezing weather and ice and snow conditions of rivers and highways and reduced rail shipments, there was reportedly little or no shortage in coal supply to consumers. Inventories at electric utility plants and steel company coke plants at the beginning of the severe weather were sufficient in most cases for at least 30 days" operations. There have been no reports of coal shortages at other industrial plants.

Jan 1, 1977

By S. L. Huang

The location and shape of potential failure surfaces in soil slopes were directly determined based on the stresses induced in the soil mass and the strength of the soil itself. Stress calculations were carried out by the finite element method with the Drucker-Prager nonlinear material model. The Mohr-Coulomb failure criterion and Mohr's circle stress analysis were then applied to the calculated stresses to determine the characteristics of the failure surface.

Jan 1, 1989

By William H. Pomroy

The potential for large-scale fires in underground fuel storage and fuel transfer areas prompted the Bureau of Mines to study fire hazards in these areas and devise improved fire safety technology for use in these areas. This report describes the Bureau's research to characterize and quantify fire hazards in fuel storage and fuel transfer areas, develop guidelines for safe and efficient fueling system design, prepare specifications for automatic fire sensing and suppression systems for these areas, test prototype systems in the laboratory and in underground mines, and perform cost-effectiveness evaluations of the devised technology.

Jan 1, 1985