Search Documents

Jan 1, 1885

By Warren H. Weisz

A cement, in the broad sense, is any substance which will cause various materials to adhere to each other. Clay was probably the first material to be used by man as a cement or binding agent. Water occurs in or is mixed with the clay to make it plastic, so that it can be formed in place. The sun and air remove the water from the clay and on drying strength is developed. The clays unless fired are not too resistant to water, therefore, their use is best when restricted to dry areas. Gypsum used as a cementitious material is not the subject of this paper, but its use dates back thousands of years. Gypsum mortars were used by the Egyptians in building such massive masonry structures as the pyramids. The Egyptian mortar consisted of a mixture of sand with burned gypsum (of an impure type of 81.5 per cent calcium sulphate and 9.5 per cent calcium carbonate) for the cementitious material. The burning of this type of cementitious material took place at relatively low temperature. These burning reactions will be covered later when the dehydration of gypsum is discussed. The setting of the partially dehydrated gypsum is considered to be crystallization from a supersaturated solution which deposits crystals of dihydrate (gypsum). In low water-content mixes, the interlocking of the needle-like crystals helps to produce higher strengths. Slaked lime made from limestone burned at higher temperatures (1648 F is generally considered as the calcining temperature, although under certain conditions incipient calcination will take place at 1250 F) is another early-period cementitious material. During slaking with water, a colloidal or amorphous hydrated lime is formed. When it is allowed to dry, it hardens and develops low strengths. On exposure to the carbon dioxide of air in the presence of some moisture, carbon dioxide is adsorbed and part of the calcium hydroxide is converted to calcium carbonate. Structures in which a lime mortar is used continue to grow in strength as this reaction proflesses. Hydrated lime has the disadvantage of not setting under water.

Jan 1, 1960

By B. P. Watson

The first crush pillars on the Bushveld platinum mines were introduced at Union Section in 1978. Before the introduction of crush pillars, serious problems were experienced when stoping advanced to a point 30 m to 40 m on both sides of the centre gully. At least three to four stopes were collapsing per month. The introduction of the pillars stopped the stope collapses in the mining area where they were introduced. The residual stresses of these pillars were never measured; however, the successful elimination of the ?back-break? problem suggests that the original pillars had a residual strength of at least 8 MPa. Apart from back analyses, very little work has been done to determine the residual strength of crush pillars and only very recently have any measurements been made. The lack of knowledge in this field has resulted in pillars being designed based on experience. Concerns about stope collapses, similar to the Coalbrook disaster, have led to larger pillars being cut in more recent times. If such pillars were cut in brittle quartzites they would always fail violently but the ductile nature of the Merensky Reef generally allows large pillars to fail without bursting. Occasionally, however, one would burst in a working area. Increased incidence of bursting has been reported on some mines at deeper levels but most of these bursts occur in the back areas. Nevertheless, the incidence of bursting increases the risk of falls of ground in already dangerous areas, and the larger pillars decrease the extraction ratio. This paper describes the evaluation of stress measurements conducted in two boreholes over a crush pillar with dimensions 2.5 m x4.0 m, and a height of 1.2 m. Boussinesq equations for vertical and shear stress were used to analyse the original measurements and provide a stress profile across the pillar as well as the residual strength of the pillar. The results showed an unexpectedly high peak stress of 280 MPa at the centre of the pillar and a residual strength of 48 MPa. The reason for the high residual strength is suspected to be the result of the stiff environment under which the pillar failed and the small height of the siding on the up-dip edge of the pillar. More measurements should be conducted on several mines to establish a range of residual strengths for narrow crush pillars.

Jan 1, 2008

Failure of rock materials is a process of crack propagation. Crack initiation takes place when the crack tip stress intensity K reaches a critical value called fracture toughness, K1C. The rock fracture toughness is known to be affected by the surrounding environment such as temperature, confining pressure and humidity. In order to examine the effect of humidity, a series of semi-circular bend tests were performed under various water vapour pressures in a rock material that is known to be anisotropic. Water vapour promotes stress corrosion of rock and therefore the fracture toughness was found to have a decreasing trend with increasing water vapour pressure. The rate of decreasing the fracture toughness depends on the microcrack density that promotes the migration of water vapour into the rock. Also in an anisotropic rock, the fracture toughness depends on the direction of crack in relation to the anisotropy of the rock material.

Dec 6, 2010

By Nick Poushinsky

OVERVIEW OF PRESENTATION ?Stantec?s Northern Presence ?Challenges for Northern Development ?Environmental Approval Challenges ?History/Expectations ?Baseline Data ?Consultation ?Regulatory Processes ?Extra ?Regulatory ?Keys to Success

May 1, 2009

By Carl Tom Blevins

Resin was first introduced to U. S. mines in 1971 and first produced in 1973. The original polyester roof bolt resin was very expensive and limited to a single cartridge size and a single slow gel time. Early resin applications were limited to very difficult ground conditions. Today approximately 80% of the over 100 million roof bolts installed in U.S. mines, tunnels, and construction projects employ polyester roof bolt resin. The industry has evolved from hand packing samples for trial testing to producing enough resin, if converted to a .9 inch (22.9mm) diameter cartridge, to encircle the world at the equator approximately three (3) times each year. Manufacturing and design improvements allow for a more consistent product with a wide range of applications at a price that is approximately 30% below our 1974 sales price. An inflation adjusted dollar buys six (6) times more resin in 2006 than in 1974. Modern gel times range from a few seconds to over 15 minutes. Viscosity is matched to bolt type and drilling machine characteristics. Multiple cartridge diameters and a wide range of cartridge lengths are offered by two operating companies. Resin manufacturers have also gone through a period of restructuring and change to meet the challenges of the mining industry. DuPont Fasloc has become Fasloc, Inc., a stand-alone company. Celtite became Fosroc then Minova, as it is known today. During this transformation, several manufacturers have either discontinued production or were absorbed. The industry led the development of the chemical grouting materials specifications contained in ASTM F432-95, Standard Specifications for Roof and Rock Bolts and Accessories. A history of the industry will be presented within a discussion of the evolution of the strength index, speed index, cartridge volume, class designation, and product marking requirements of ASTM F432-95.

Jan 1, 2006

By J. H. East

THE RIFLE, COLO., oil-shale project of the Bureau of Mines was a facet of the re-search and development activities conducted under the Synthetic Liquid Fuels Act (Public Law 78-290) of April 5, 1944. The principal objectives were to devise efficient methods to mine and retort oil shale and to refine shale oil into usable products, at a total cost low enough that shale oil could supplement the domestic supply of petroleum at competitive prices. The Rifle project included three major divisions: (1) Mining, (2) retorting, and (3) refining. The major functions of the mining program were to supply oil shale to the retorts, to devise mining procedures, and to develop an under-ground-mining method by which oil shale could be produced safely at an unusually low cost per ton. The selected mining procedures and direct mining costs were demonstrated by sustained test runs.

Jan 1, 1964

Workers at Anaconda Aluminum Company's primary aluminum smelter at Sebree, Ky., were back on the job December 1, after agreeing to a new 3-year contract. The old contract had expired November 15. On December 20, the Aluminum Company of America reportedly shut down a 42,000-ton-per-year potline at its Wenatchee, Wash., primary aluminum smelter and half of a 23,000-ton-per-year potline at its Vancouver, Wash., smelter as a result of a power cutback by the Bonneville Power Administration. A1 so in December, Kaiser Aluminum & Chemical Corp. reduced overall power at its Mead and Tacoma, Mash,, smelters and shut down one of eight 27,500-ton-per-year potlines at Mead. Reported shutdowns for the firms since September have amounted to 76,000 tons for Alcoa and 50,000 tons for Kaiser. Alcan Aluminum Ltd. announced plans to double the generating capacity at its Kemano hydroelectric power plant in British Columbia to 1,916 megawatts. The additional power would be equal to that required of a primary aluminum smelter with an annual capacity of 567,000 tons.

Jan 1, 1980

By J L. Mauk

The Martha epithermal Au-Ag deposit contains multiple generations of quartz veins with a range of textures. We examined: +        vein textures, +        crosscutting vein relationships, and +        the paragenetic sequence within the pit walls as well as a wide range of hand specimens. Samples include host rock, breccia, and veins, but these groups are not distinct; instead, they form a continuum.   Veins at Martha mine show a wide range of textures on a local scale; these textures also change significantly over both the lateral and vertical extent of the pit. Common textures include crustiform bands, comb quartz, colloform bands, platy quartz, massive quartz, drusy quartz, sedimentary textures and brecciation.   Vein grades relate to textures. Many textures, including crustiform, platy, cherty, and sedimentary textures display predominantly low grades, but some textures are linked with high grades, such as ginguro, massive and comb quartz where they are associated with visible base metal sulphides and/or electrum. Host rocks and most breccias are low grade, as most samples contain <2 ppm Au.

Jan 1, 2006

By D. J. Pyra, J. Kudelko, Korzekwam W.

Polkowice region (Lower Silesia, Poland) is an area, where the copper mining activity started about 40 years ago and new technologies were applied. There are 3 underground mines, 3 processing plants, tailings pond (the biggest one in Europe), pipelines for flotation waste transport, railways. Although new technologies were applied during the copper ore exploitation, the environment in this area were polluted mostly by dust containing copper, lead, zinc and arsenic. Estimated values of heavy metals in polluted soils were compared to the natural contents of this metals. The geochemical background for Polkowice area was defined. The pollution zones occur around mining facilities. Copper ore exploitation and processing is planned for the next 20-40 years depending on market situation. After mines and other facilities closing the most important problem will be sustainable development of this area. To evaluate the scope of revitalization activities the analysis of recent soil environment condition will be necessary as well as forecasts for pollution migration. Geostatistic methods used also in mining will be very helpful for this task.

Jan 1, 2005

By César Bernal M

El presente trabajo busca establecer el mejor plan de explotación de la mina Cobriza a través del nuevo proyecto de expansión. El plan de explotación señala que los ciclos de explotación, el número de tajeos requeridos por el método de corte y relleno, la selección del equipo de mina, así como los servicios auxiliares para suministrar el tonelaje necesario de mineral a la nueva planta de Coris.

Nov 8, 1982

By F. E. ROGERS

CUSHMAN TUNNEL No. 2 is adjacent to the Hood Canal, near potlatch, Wash. It is 17 ft. inside .diameter, about 13,000 ft., or two and one- half, miles in length, and is a part of the second unit of the Cushman power project. It connects Cushman ' Dam No. 2 and the penstocks that lead to the power house on the beach about 400 ft. vertically below the outlet of the tunnel. One shaft, 190 ft. deep, and two adits between 300 and 400 ft. long, were provided to speed up driving operations. his arrangement gave 6 working headings, which were operated 24 hr. daily. The shaft provided a manway, cageway, and skipway.

Jan 1, 1931

By A. Roberts

This paper reviews progress in equipment design and in the techniques applied to mine lighting in Great Britain. The incidence of the disease miner's nystagmus, which was a major source of concern only a few years ago, has now diminished, largely owing to improvements in standards of lighting in mines. The reorganisation of the coal mining industry, involving increasing mech-anisation, together with new safety legislation, has brought about the widespread use of mains electric lighting underground. An account is given of some of the results of research to determine the lighting conditions needed for compliance with the compulsory legal requirement of "sufficient and suitable" general lighting at specific localities in British mines. Some details are given of the techniques applied and the results of recent research in the problem of glare from miners' cap lamps. Of the various factors in the working environment of the miner, it is true to say that lighting is seldom given attention comparable with that devoted to other factors, such as dust, heat and humidity, or atmospheric gas content. No doubt one reason for this lies in the ability of the human eye to adapt itself to low brightness levels. Be that as it may, the fact is that at the turn of the 20th century the miner's working light improved little throughout the centuries during which mining technology has developed. Indeed, in coal mines which encounter a methane explosion hazard, flame safety lamps, with a luminous intensity less than one candle power, were virtually the sole means of lighting during almost the whole of the 19th century. The 20th century has witnessed a substantial improvement in lighting techniques underground in coal and metalliferous mining. In Great Britain the general pattern has been one of standards periodically raised by the implementation of Statutory Regulations imposed under successive hlines Acts, but it is fair to add that the more progressive mining companies usually anticipated the Statutory Regulations, which when they have been put into effect have served to turn into general practice what was already being done at the better mines. In earlier years, official requirements were limited to the specification of approved lamp designs, with stipulated minimum values of luminous intensity and light output, but more recently the necessity of satisfactory maintenance of standards during service has been recognized, and the current regulations not only require that a maintenance organisation should exist, but also specify a maximum permissible depreciation below initial approval standards.'

Jan 1, 1961

Jan 1, 1900

By Paul J. Axtell

This case history describes the foundation design and construction for the New Mississippi River Bridge, presently under construction in St. Louis, Missouri. The 1,500 ft (457.2 m) main span of the cable-stayed bridge is supported by two delta tower pylons in the river, with anchor piers on each bank. The final foundation design was completed as a part of an Alternate Technical Concept (ATC) proposal by the winning construction team, and utilized drilled shafts up to 11.5-ft (3.5-m) diameter that were socketed into very hard limestone. As part of the ATC foundation design, a full-scale, bi-directional static load test was performed to verify the design and allow use of higher resistance values. This paper presents the results of the site exploration, construction of the load test shaft, details of the load testing, and a comparison of the test results with various design parameters.

Jan 1, 2011

By Edward E. Johnson

The U.S. economy made significant progress in 1984. The current-dollar gross national product (GNP), the market value of the Nation's output of goods and services, increased almost 11 percent over that of 1983 to slightly more than $3.66 trillion (table 1), and the real gross national product increased almost 7 percent.2/ Such rapid growth in real GNP has not occurred since the early 1950's. Real final sales increased only 5 percent during 1984, and real business inventories increased $24.8 billion ($57.9 billion in current dollars). Total employment of 106.7 million was an all-time record, and the unemployment rate declined from 9.5 percent in 1983 to 7.4 percent in 1984. During 1984 the U.S. dollar showed great strength on international markets, contributing to large current-dollar negative net exports of goods and services (-$62.5 billion) and even larger negative net exports of merchandise (-$107.6 billion). The strong dollar and the substantial increase in net imports of goods and services helped reduce U.S. inflationary pressures and provided a major source of loanable funds for financing domestic private investment.

Jan 1, 1985

By K. Schimann, H. D. Knipping, J. P. Fouques

"RESUMELe gisement d 'uranium de Cigar Lake, dans la région de l'Athabasca au nord du Saskatchewan, fut découvert en mai 1981 par Cogema Canada Ltée, opérant pour Ie compte de la ""Waterbury Lake Joint Venture"".Le corps minéralisé. qui est dépourvu de toute expression directe en surface, est situé a la discordance entre les met sédiments du wottaston Group (Protérozoïque inférieur ou Aphébien) et les grès de l 'Athabasca (Protérozoïque moyen ou Hélikien), à une profondeur de 410 a450 m.Fin 1984, Ie gisement était reconnu par 105 sondages minéralisés repartis sur une longueur de 1800 m, pour une largeur comprise entre 25 et 105 m. 11 se présente sous forme d’une lentille aplatie de 5 a30 m de puissance, et montre une remarquable continuité d'ensemble. Une ride ou bombement topographique de la discordance est associée au gisement surtoute sa longueur.A l'échelle régionale, le corps minéralisé à est associe à un corridor structural d’orientation est-ouest, a l'intérieur duquel des facies particuliers aténdance blast mylonitique sont développes dans les formations métapolitiques agraphite du socle métamorphique. Il est entouré par un halo d'altération très important, caractériser Ie développement de minéraux argileux alumino-magnesiens (illite-chlorite).La minéralisation est située, pour la plus grande part, dans les grès d'Athabasca, et se compose essentiellement d'uraninite et de sulfo-arseniures de nickel et de cobalt,De nombreux levés géochimiques et géophysiques ont été effectues dans la région de Cigar Lake. Aucune anomalie ne peut être associée directement au corps minéralise, mais la combinaison des données en provenance de plusieurs sources s’est révélée fort utile au niveau de l’interprétation géologique régionale et de la définition des cibles de sondages a l'intérieur des zones reconnues favorables.Le gisement de Cigar Lake présente de nombreuses analogies avec plusieurs des gites classiques de la région de l'Athabasca; il est caractérise en particulier par l'intensité des phénomènes d’altération et la présence de minéralisations extrêmementriches.En 1984, les réserves géologiques globales estimées par géostatistique sur I ‘amas minéralise principal s 'élevaient a 110 000 tonnes d'uranium, aune teneur moyenne de 12.2%, avec une précision de 25% à l'intervalle de confiance de 95%.ABSTRACTThe Cigar Lake uranium deposit, in the Athabasca area of North Saskatchewan, was discovered in May 1981 by Cogema Canada LId., as operator of the Waterbury Lake Joint Venture. The deposit, which is devoid of direct surface expression, is located at the unconformity between the Lower Proterozoic (Aphebian) Wollaston Group meta-sediments and the Middle Proterozoic (Helikian) Athabasca sands tone, at a depth of 410 m to 450 m below surf ace.AI the end of 1984, the deposit had been defined by 105 mineralized holes over a length of 1800 m and a width of between 25 m and 105 m. It has the shape of a flat-lying lens 5 m to 30 m thick and shows a remarkable longitudinal and latera continuity from the information obtained to date. A well-defined bulge of the unconformity underlies the mineralized zone over its entire length.The deposit appears to be controlled by an east-west-trending structure within which a particular rock facies (""augen gneiss"") has developed in the graphitic metapelites of the Wollaston Group. It is surrounded by a strong alteration halo affecting both sandstone and basement, characterized by extensive development of Mg-A I rich clay minerals (illite-chlorite).The mineralization is hosted principally by the Athabasca sandstone, and consists mainly of uraninite and sulfo-arsenides of nickel and cobalt.Numerous geochemical and geophysical surveys have been carried out in the Cigar Lake area, and no specific geochemical or geophysical anomaly can be directly associated with the mineralized body, although there may be locally a good coincidence. However, a combination of several methods proved extre"

Jan 1, 1986

By Robert C. Merritt

Laboratory amenability studies as well as a pilot heap-leaching investigation of low-grade sandstone uranium ores from Wyoming, New Mexico, and Colorado are described. Sulfuric acid heap leaching with oxidation, for 120 days, extracted up to 98 percent, 90 percent, and 79 percent U308 from Wyoming, New Mexico, and Colorado ores, respectively.

Jan 1, 1976

By C Thompson, D Connelly

The history of mill liners has evolved over time and this paper tracks the changes and development of liner technology. It provides an overview of the primary types of liners, the design and the materials of construction. The design of a mill liner is driven by application, materials of construction, casting technology and handling issues. The choice of solid steel, grid liners, rubber or composites and magnetic liners is based on many factors.The methods used for monitoring wear and predicting eventual change out time are many and varied. The contribution of discrete element modeling (DEM) analysis in predicting wear profile is discussed.Mill trajectory and DEM software programs are used with great effect to predict the effect of lifter height, face angle, high low lifters or mill speed. In the field, trial and operational experience is used or improvements/design concepts at one operation are applied to another. Broken mill lifters, accentuated wear and other problems can be better understood using hardness testing, chemical analysis and photo micrograph analysis of pearlitic or martensitic structure along with fracture face observations. This forms a part of the typical root cause analysis. However given correct and sound liner and lifter, feed and discharge design media selection, and materials of construction, the majority of premature liner or bolting failure is normally attributed to incorrect operational methods such as excessive high ball to feed ratio, incorrect mill speed relating to lifter ball throw, incorrect media selection, "tramp" material entering the mill charge from upstream or recirculating process and understanding the specific mill operation in question.It is hoped that this paper will benefit mill operators who are faced with challenges of improving wear life and at the same time optimizing mill throughput and performance.CITATION:Connelly, D and Thompson, C, 2013. The selection design and application of mill liners for large wet grinding mills, in Proceedings MetPlant 2013 , pp 133-140 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

By Evelynn Stirling

Agenda ? Emissions legislation ? Cummins Tier 4 Technology ? Cummins Experience with Technology ? Operation and Maintenance Impact The Emissions Challenge ? The 2014/5 emissions regulations present the most significant challenge to our customer?s diesel powered equipment design and operation in recent history? ? ?and Cummins has the solution.

Aug 1, 2013