Search Documents

The variation of carbon monoxide and hydrogen utilization with the amount of the reductant in the blast furnace bosh gas was investigated for the No. 4 blast furnace at The Broken Hill Proprietary Co. Ltd.iron and steel works. Newcastle. The degree of CO utilization decreased with increasing CO in the bosh gas; the H., utilization increased with the H., content of the gas. Empirical relationships for CO and H., utilization are proposed.H2, is 3-6 times as effective a reductant as CO at present levels of CO (34-39 per cent) and H2 (6-10 per cent) in blast furnace bosh gas. H2, gas injection into the blast furnace is proposed as a means of lowering the coke consumption, and the economics of H2 injection are evaluated.

Jan 1, 1975

As ore deposits become finer grained the requirements for regrinding before cleaning or leaching have increased substantially. Despite this increasing need, there is no standard test to predict grinding energy requirement below 70 microns. The standard Bond Mill test applies for coarser ball milling, but is not appropriate for stirred milling with fine media grinding to 70 microns. With no industry -standard test, the energy requirement is often made on the basis of supplier estimates or benchmarking against similar applications. Yet suppliers use vastly different scale-up methods which result in widely different energy estimates. Estimates can differ by 100-300% even for similar mills. This must result in serious errors to install either too much or too little grinding power. This paper explores this by comparing the actual performance of full scale regrind mills against their original design estimate. It confirms that serious scale-up errors have been made, and have then been perpetuated by ?benchmarking?. The test conditions to achieve accurate power estimation are discussed. The essential test conditions are: continuous (not batch) tests, ensure steady state (no coarse fraction retained in test mill), correctly account for classification, measure energy directly (not inferred), and using the same media size as the full scale installation. Failure to correctly address even one of these factors can bias results by 40%; failure to address several multiplies the error.

Jan 1, 2011

By R L. Brathwaite

As part of an investigation of the deep structure of the Waihi Basin, an extensive set of resistivity measurements was recently collected by DSIR Geology & Geophysics. The objective of this work is to map deep resistivity changes throughout the Waihi area in order to contribute to a better understanding of the regional geophysical structure. This research is also aimed at improving techniques for locating 'deposits of epithermal mineral resources, and helping to establish their origin and genetic relationship to fossil geothermal systems.   The results indicate that the basin south of Waihi is underlain by an extensive layer of low resistivity, modelled as a 5ohm-m layer several hundred metres thick. Lake sediments (mudstones), as exposed in the south western part of the basin, near Waitawheta, are the most likely source of this low resistivity layer, although hydrothermally altered clays and/or elevated temperatures are other possible causes. Strong northeast trending anisotropy is also observed, implying structural links from Waitawheta through to Golden Valley. The observed resistivity pattern is consistent with a æburied calderaÆ or æfaulted depressionÆ structural model for the basin, as inferred from gravity and magnetic data.

Jan 1, 1991

By Milford L. Skow

MICA is a group name for a number of complex hydrous aluminum silicate minerals that have a sheet or platy structure and extremely variable and complex compositions containing various metallic ions, particularly those from the alkali group. Muscovite and phlogopite, the two varieties of significant commercial value, are the principal consideration of this report; muscovite has major importance industrially. The mica crystal, because of its laminated structure, can be split easily and accurately into thin films that are transparent, flexible, elastic, tough, and waterproof and have outstanding dielectric and insulating characteristics. This combination of properties is not duplicated in any other known substance. The world production of mica can be divided into two main classifications: (1) Sheet mica and (2) scrap mica (including flake mica). In general, separate divisions of the industry produce these two classes of mica, which differ widely in their uses and in the forms in which they are marketed. A glossary of mica terminology is given in appendix A.

Jan 1, 1962

Local conditions at Hatches Creek are described, together with the mineralogy, mining and treatment of tungsten ores, with particular reference to procedures adopted by Pimer Mines, N.L.The Hatches Creek tungsten field covers an area of about 20 square miles in: Central Australia; 285 miles' N.E. of Alice Springs. Access is by rail to Alice Springs, then by 200 miles of bitumen highway to Barlo Creek and 8,5, miles of bush track to the field. Passengers can also reach the mines by... A semi-desert climate prevails Rain; generally in the form of thunderstorms falls in the summer months: December to March. Average annual rainfall is approximately 15 inches but there is great variation from year to year, occasional droughts being followed by torrential downpours. Vegetation is sparse except in the wide creek beds. Surface water occurs in rock holes some of which, spaced miles apart, carry permanent water...

Jan 1, 1955

By Valérie Tremblay

Plan de la presentation ?Laboratoire d?analyse des fluids ?Gestion des contaminants ?Condition Monitoring Avantages reliés aux analyses ?En savoir plus!! ?pour minimiser les coûts d?opération; ?pour prévenir les défaillances catastrophiques; ?pour maximiser le rendement des équipements; ?pour maximiser la longévitédes équipements; ?pour permettre des périodes d?entretien planifié.

Feb 1, 2008

By A. D. Storrie

An underground wet shotcrete trial was completed last year to determine the effectiveness of wet shotcrete as an alternative support mechanism to dry shotcrete in the kimberlite environment. The wet shotcrete was manufactured at the underground batch plants, transported to site using an agiecar and transferred to the shotcrete pump. The wet shotcrete is pumped to the nozzle where compressed air at 7 bar and an accelerator, Meyco SA 160, is added and enables the shotcrete to be placed successfully onto the tunnel wall. No tunnel guard was previously placed on the sidewall and hangingwall. Geotechnical testing indicates that the Grace fibre performed extremely well with the energy absorption tests at 7 kg/m3and 8kg/m3where both achieved over the mine requirement of 750joules. The Grace fibre and wet shotcrete mix also achieved a compressive strength in excess of 55 MPa, well above the 45 MPa requirement for Premier Mine. The recommended wet shotcrete mix design is therefore based upon: [Material/ CriteriaQuantity/m3Units ?Lafarge 42.5 Duratech500kg ?Condensed silica fume40kg ?Rayton Sand1.558Ton ?Delvocrete stabilizer 103.6litres ?Glenium 27CH5.4litres ?Meyco TCC 7355litres ?Water230litres ?Meyco SA16025litres ?Fibre8kg ?Cement/Water Ratio2.35? ?Water/Cement Ratio0.43? ?Flow615 mm] If the wet shotcrete system is implemented there is a potential for Premier Mine to make major savings. In South Africa there are two suitable wet shotcrete machines available for the mining industry, the Spreymec, manufactured by Tamrock and the Fermel/Meyco wet shotcrete machine. The Spreymec is a fully imported machine. The Fermel component is manufactured in South Africa and the Meyco shotcrete components are imported and supported by MBT (Master Builder Technologists) in South Africa. The Fermel/Meyco machine is assembled in South Africa. Premier Mine has allocated some R2, 100,000 towards the implementation of the wet shotcrete system. If implementation is successful there should be an internal rate of return gain of 76% with regard to this project.

Jan 1, 2001

By J. Ling, L. Racine, P. Cousin, A. R. Laplante

"The problem of gold recovery by gravity from high density gangues is first discussed from a fundamental perspective. Three potential difficulties are presented: poor liberation and fine gold particle size, concentrate bed erosion by coarse dense particles, and slow percolation of gold particle through the high density gangue bed. Two case studies are presented to illustrate the impact of these three problems on circuit performance and the feasibility of gravity recovery. It is concluded that careful testing can determine the scope of the first problem and feed preparation can limit the extent of the second. The third problem is clearly the most serious and results in lower gravity recoverable gold recoveries than would be achieved with the same recovery effort on a low density gangue application.IntroductionSince the commercialisation of the Knelson Concentrator in 1980, gold gravity recovery has experienced a surge in interest, in Canada and the United States first, then Australia, Zimbabwe and Russia, and finally worldwide. Table I details number of units sold in various countries, which corresponds approximately to their importance as gold producers 1. Exceptions. such as the low rank of South Africa or the importance of Zimbabwe, despite the much higher gold throughput of the former, are generally the result of differences in the effectiveness of the local marketing strategies, as well as a reflection of the ""philosophy of recovery"" prevalent in the country.The impact of the Knelson has not been felt equally in all plants. Typically, a highly successful application falls into the following categories: (a) alluvial or hard rock recovery for which gravity is the sole recovery method, (b) hard-rock free gold milling with ores which have a very high gravity-recoverable gold (GRG) content, (c) low grade sulphide copper-gold ores which include flotation ahead of cyanidation and (d) free-milling gold ores ahead of Other applications can be successful, but are not as common. The ""explosion"" of centrifuge concentration, of which the Knelson is the most successful but by no means the sole model, has created a certain euphoria which can be summarized as ""gravity recovery will improve the profitability of gold milling, no matter what."" This presentation is about applications that are not so successful, or even downright unsuccessful. The rationale is not to down-play gold gravity recovery, but to set it in its rightful position: metallurgically, it is not appropriate all of the times; it can become inappropriate if poorly designed; and it can be metallurgically possible but economically unjustifiable. In this paper, this will be illustrated and explained rather than demonstrated, with the use of both industrial plant surveys and laboratory test work. Alternate gravity approaches will be suggested."

Jan 1, 1997

By M P. Simpson, J L. Mauk

The Golden Cross, low-sulfidation, epithermal deposit shows a number of features that are directly or indirectly related to boiling hydrothermal fluids. Occurrences of lattice calcite and their quartz pseudomorph equivalents in veins, and occurrences of adularia in veins and in the surrounding altered rocks in the vicinity of ore, are both direct evidence of deposition in the presence of boiling hydrothermal fluids. Loss of carbon dioxide causes calcite deposition (platy variety) near the level of first boiling, while adularia deposits due to the attendant pH increase along the cooling flow path. Indirect evidence of boiling include crustiform-colloform quartz banding, late massive calcite veins, clay-carbonate alteration in the shallow and peripheral parts of the ore zone, and the restricted vertical interval of precious metal mineralisation. The colloform quartz banding strongly resembles the banding in amorphous silica deposits found in geothermal surface pipes. This implies that fluids ascending the Empire Vein structure were saturated in amorphous silica. If so, then they must have undergone phase separation, which initiated at considerable depth (e.g. =1000 m) and very hot temperatures (e.g. =300¦C). On the basis of stable isotope data, late massive calcite veins appear to have deposited from CO2-rich steam-heated waters. Calcite deposited along heating paths as these waters descended into the upflow zone during late stage collapse of the hydrothermal plume. In active systems, such steam heated waters form by deep boiling. The high CO2 contents of these waters promote hydrolytic alteration and the formation of clay-carbonate alteration. Reaction path modelling using CHILLER and a deep, Broadlands-Ohaaki water as an analogue, shows that minerals deposit along boiling flow paths over discrete spatial intervals. Calcite and adularia deposit near the site of first boiling, followed by gold and then by amorphous silica. For deep boiling starting at 300¦C, these minerals deposit over a path length that exceeds 1000 m. The distribution of banded quartz and gold at Golden Cross are consistent with such a boiling model. However, the elevation of first boiling must have fluctuated over 500 m to account for the coincidence of lattice quartz (pseudomorphs of platy calcite) and adularia, crustiform-colloform silica and gold over distances of a few centimeters in veins. We deduce that a downward propagating boiling front and expansion of two-phase flashing in a flowing water column occurred during episodes of high vertical permeability and fluid flux in the Empire vein structure.

Jan 1, 2000

Vitrinite reflectance forms the basis of a study of coal rank variation in two areas of the Upper Hunter Valley, New South Wales, on the northern margin of the Sydney Basin. A selective analysis procedure, based on samples rom twenty-two boreholes, has resulted in a small range of reflectance values for each sample and consequently a high degree of significance for calculated mean values. The patterns of rank distribution derived from these data have facilitated an interpretation of the rclative timing of coalilication and deformation in each area.This study provides support for the suggestion by several authors that there were at least two periods of folding in the tJpper Hunter Valley. In the Hebden-Ravensworth area, minor folding took place after most of the coalilication was completed.To the west, in the region of the Muswellbrook Anticline, coalification occurred during or after the formation of this major structure. Tectonic instability during deposition of the Singleton Super-Group, in the region of the Hunter-Thrust on the basin margin, is evidenced by rank variation suggesting differential subsidence across this zone.

Jan 1, 1980

By Nicholas G. Theofilos

The Bahamian economy weathered the worldwide recession of the last few years better than most developing countries. This was mainly owing to the ties between the tourist industry of the Bahamas and the U.S. economy. The mineral industry played a minor role in the country's economy. The chief mineral exports included an increasing amount of petroleum products horn the country?s 500,000-barrel-per-day refinery, steel pipe, salt, and aragonite. A 60,001)-barrel-per-day desulfurization facility was completed by Bahamas Oil Refinery Co. (BORCO) in Freeport. The project included vacuum gas oil desulfurization, hydrogen and sulfur recovery, steam generation, water desalinization, and offsite facilities.

Jan 1, 1980

By John E. Tilton

The ability of companies and countries to mine copper and other mineral commodities competitively and in the process to generate new wealth depends on their mineral endowment. Chile, for example, produces and exports copper because it is well endowed with high-quality, low-cost deposits. This production creates wealth that benefits mining companies and their stockholders, the government, local communities, as well as copper consumers around the world. The widespread perception that mineral endowment must largely determine competitiveness, or what economists call comparative advantage, must be true at any particularly moment. Countries with abundant reserves must be competitive. This follows from the definition of reserves — the quantity of a mineral commodity found in discovered deposits that are profitable to exploit under current conditions. As a result, it is a tautology and not particularly interesting. The important question is what causes reserves to change over time, producing in the process new wealth and shifts in competitiveness?

Jan 1, 2003

By David Baughman, Steven Axen, Ray V. Huff, Donald H. Davidson

Introduction In situ leaching (ISL) is an alternative method of mining uranium from deposits that are low-grade, deeplying, and water-saturated. ISL recovers uranium by transporting fluids through rock rather than by moving rock, a concept the Chinese developed over 2000 years ago for water production. This technique eventually evolved into production systems for oil, gas, sulfur, and salt. More recently, in situ methods have been developed to produce shale oil, gasified coal, geothermal energy, uranium, and copper. ISL uranium operations began in the early 1960s with Sabine Production Co. in south Texas. About the same time, Utah Construction and Mining Co. (Anderson and Richie, 1968) started similar operations in Wyoming's Shirley Basin. During the 1970s, six commercial operations were started in south Texas, (USBM, 1978) and a number of pilot operations were in various stages of development in Colorado, Wyoming, and New Mexico. This paper reviews some of the technical and economic aspects of the ISL process and briefly discusses key subsurface engineering functions as¬sociated with well pattern design and operation. While flow characteristics of a deposit are of prime importance, the following information is also needed: Depth, ore grade, total contained metal, ore thickness, flow conductivity (permeability), void space in rock (porosity), mineral type and distribution, natural groundwater flow, and structural features. Solvent selection, which is important to the economic success of the operation, takes these factors into account: Composition, rate of metal solubilization, interaction with gangue minerals, impact on rock permeability, impact on materials of construction, trace metal solubilization, cost, availability, and handling problems. Overview of ISL An ISL operation consists of these functions (Fig. 1): 1. Chemicals to dissolve and maintain uranium in solution are prepared at the surface extraction facility. 2. A set of injection wells forces the solvent into rock pores of fractures using pressure in excess of the deposit's hydrostatic pressure. 3. Solvent travels through the rock and reacts with uranium minerals to dissolve them. The solvent usually consists of an oxidant and a complexing agent in an acidic or alkaline medium. 4. A set of production wells creates a low-pressure sump where metal-enriched solution is collected for transport to the surface. 5. The enriched solution is processed to recover uranium and to separate the leaching solution for recycling through the system. The economic performance of an in situ operation may be estimated by integrating these related factors: (1) the flow rate of solution processed through the system, (2) rates of fluid injection and production from wells, (3) the rate of mineral solubilization in the liquid phase, and (4) the volume of rock swept by the fluid. As these factors reveal, ISL involves the technical disciplines of petroleum engineering, ore deposit geology, and hydrometallurgical processing. Wellfield Design Just as mineral engineers use drillhole information to plan a conventional mine, in situ engineers use similar information to design a well field. A thorough knowledge of deposit geology and reservoir properties is required. Early application of pressure transient testing, such as

Jan 2, 1980

The Karangahake gold-silver deposit is located 11 km west of Waihi in the southern part of the Hauraki Goldfield. Historically it was the second largest bullion producer in the goldfield with a past production (1882 - 1944) of 126.712 tonnes of gold-silver bullion (Au:Ag ratio of 1:3.3) from 1 142 315 tonnes of ore grading 27.4 g/tonne gold equivalents.

Jan 1, 1987

By Roderic A. Ellman

The new Woodrow Wilson Bridge (WWB) will replace the existing bridge over the Potomac River to connect Alexandria, Virginia to Prince Georges County, Maryland. The new WWB will extend approximately 1.1 miles across the river, with a 367-ft long bascule span in the main river channel where the water depth is about 36 ft. The subsurface soil profile consists of up to 50 ft of a soft organic silty clay layer that is very vulnerable to scour, underlain by a deep deposit of hard sandy clay. Foundation construction in the Potomac River required the use of cofferdams to allow structural concrete work to be performed in the dry. This paper will the present the types of cofferdams used to construct the foundations for the WWB replacement project. The bridge is primarily comprised of fixed spans in relatively shallow water and a bascule span over a navigation channel in relatively deep water. Foundation construction included the installation of 48? to 72? open end steel pipe piles and cast-in-place concrete pile caps. To achieve the desired bridge appearance, pile caps were required to extend below the water surface and below the existing river bottom in shallow water locations. Conventional steel sheet pile cofferdams with tremie concrete seal were used to construct fixed span, shallow water piers. Selection of deep water bascule span foundation cofferdams was governed by several factors including contraction scour, environmental considerations and cost. Potomac River cofferdams, i.e., relatively shallow depth cofferdams that are supported by the foundation piling were selected. This cofferdam system provided a shallow profile which minimized contraction scour and the amount of filling in the river. Design issues include load selection and cofferdam stability in very soft alluvial soils. Construction issues include erection sequence, tremie concrete mix design and placement procedures.

Jan 1, 2013

Permian coal seams from the Tomago Coal Measures in the Northern Coalfield, New South Wales, were analysed petrographically and reflectance measurements made for each. Vitrite contents were moderate to high for most of the coals but for two they were very low.The mineral-matter contents were low to moderate by Australian standards. Different profiles of a particular seam could be correlated by petrographic methods.Standard seam profiles were drawn up and from these an idealized Tomago seam sequence was compiled. All the coals were of high-volatile bituminous rank. Their carbon contents, but not thcir reflectances, varied significantly with the quantity of vitrinite present.

Jan 1, 1968

By M. P. Hay

"For a model to be successful it must address the concerns and needs of a target audience. Further, the model must demonstrate the same patterns of behaviour as the real system, and need only be complex enough to meet this objective. If the model is too complex it can become unusable to those who need it most.With this in mind, SUPASIM has been developed for the practical metallurgist requiring only laboratory flotation rate data as input. Some 35+ successful plant simulations have been completed since 1985. The approach of SUPASIM is to characterise an ore, organise information in an understandable way and add structure to the complex flotation situation and hence support the metallurgist to interpret the relationship between variables and optimise the flotation process.The paper describes the basis on which the model was developed and sets out to provide an insight into interpreting laboratory flotation kinetics and their physical meaning in a production plant and the influence floatable gangue has on float performance and plant design. A case study illustrates how the ratio of slow floating mineral to gangue can influence circuit design and improve recovery on a plant scale.INTRODUCTIONThere is an enormous amount of useful data in the results of a laboratory scale rate test. Each variable of fraction and rate, for mineral, metal and gangue has a physical meaning in the plant. The link between float kinetics and the plant in respect of recovery, grade, pulp density, pulp flowrate, residence time, number of stages of cleaning and circuit configuration has been established by the author in the process of developing SUPASIM."

Jan 1, 2005

By J. E. Forciea, O. E. Palasvirta, L. G. Hendrickson

AH pilot and commercial plants working with Mesabi Range taconite employ wet magnetic separation. Progress is being made with a dry magnetic process, but this has not yet been applied to taconite except in the laboratory and pilot plants. Flowsheets in all five plants are similar, including multiple stages of grinding, each followed by magnetic separation, which rejects a finished tailing. The flowsheet in Fig. 1 is used in the preliminary and commercial plants of the Erie and Reserve mining companies and in Unit C of Oliver's Pilotac plant. At Erie the desliming operation is omitted. In the Reserve plants two ball mills are used with each rod mill. Pilotac uses flowsheet 2 in Unit A-B and has also tested flowsheet 3. Principal differences in the three flowsheets are the number of grinding stages and the type of roughing. The terms open-circuit roughing and closed-circuit roughing are best defined by the diagrams. Special Test Data Given in Table I: For the Erie and Reserve commercial plants, Table I reflects routine conditions. Pilotac, the experimental plant, has been run with several flowsheets, including those followed at Erie and Reserve's commercial operations. Pilotac data for these last two flowsheets are similar to commercial plant results and are not repeated in Table I; statistics are given, however, for special test conditions. using other flowsheets. when the objective was to 'to extra-grade concentrate, Variations Among Taconites: Although crude ore tributary to these plants is generally classified as taconite, there are important differences in mineralogy and fineness of dissemination.

Jan 1, 1959

IT is not intended that this paper should be regarded as an account of the geology of the Lyell district. It is merely a synopsis of some of the conclusions recently arrived at in regard to the stratigraphic and structural geology, compiled to act as a guide to those members of the Australasian Institute of Mining and Metallurgy attending the Queenstown meeting who are interested in economic geology. The attempt has been made to present certain salient features, omitting a mass of detail, which, although important in the complete investigation and understanding of the economic geology, yet would be confusing to a group of geologists making a short visit. The location of some of the significant occurrences bearing on the main problems and conclusions are indicated in the text in order to enable members to plan the location and direction of their excursions...

Jan 1, 1927

By W. Abdellah

The purpose of this paper is to establish a qualitative method to estimate the risk level (e.g. rating and ranking) resulting from mining activity. Risk is the product of two factors: probability of failure and cost of consequences. A resultant assessment scale matrix is then used to assign a risk index value which is directly proportional to the potential for excavation instability. A case study, the No. 1 Shear East orebody at Vale?s Garson Mine in Sudbury, Ontario will be examined. A three-dimensional, elastoplastic, finite difference model (FLAC 3D) is presented for a mine development intersection situated 1.5 km below ground surface. The developed assessment scale matrix is used to estimate risk index for intersection (2981) located on 5000 level. The results are presented and categorized with respect to risk-index value, probability of instability, cost of consequence, and mining stage.

Jan 1, 2014