Search Documents

By Kwong. Kyei-Sing

Gasification is a process that converts a carbon feedstock into synthesis gas (CO+H2). Slagging gasifiers operate at high temperature and pressure and in a corrosive-wear environment from the slag. Cr2O3-based refractory linings are used to protect the steel vessel that comprises the gasifier from the aggressive gasification environment. Increasing service life of the gasifier is one of the keys for wide spread development of this technology. In support of the goals, research on the gasifier atmosphere, the slag chemistry, the interaction of Cr2O3 refractory with different feedstock mixtures (e.g., coal and petcoke) were characterized by post mortem analysis of bricks from service in gasifiers and thermodynamics simulation of the environment. Examples demonstrating how thermodynamic calculations can explain the post mortem results and make predictions of material interactions will be given. Attention is placed on the possibility of Cr+6 in different feedstock mixtures and operating conditions.

Jan 1, 2010

By B. M. Coombes

The McCracken and Stacey (1989) method of assessing geotechnical risk for largediameter raisebored shafts has been the basis for most Australian pre-construction raisebore investigations for the past 20 years. At the time of its publication, the McCracken and Stacey (M&S) Method did not include a database of raisebore diameter and rock mass conditions versus actual performance. It did, however, provide a chart that quantified geotechnical risk in terms of proposed shaft diameter and the raisebore rock quality index, QR. Two parameters, RQD/Jn and Jr/Ja were identified as being critical to raisebore stability, but the contribution of these to overall raisebore stability was not quantified. Peck and Lee (2008) published a database of raisebore performance from Australian case histories. Raisebore diameter and ground conditions, in terms of a Lower Bound QR value, were presented for 50 cases versus raisebore performance. This paper updates the database with further case histories and corrected SRF values. This paper further evaluates the reasons for the variable raisebore performance for similar RSR values. For all case histories, three parameters, RQD/Jn, Jr/Ja and Jw/SRF are investigated to assess their influence on raisebore performance.

May 1, 2011

By N. Sahin, K. Baris, A. Ozarslan

This paper aims to assess the current and future role of coal in energy strategy of Turkey and evaluates the compatibility of the policies to the EU energy policy and strategy. The Turkish government set targets to utilize more coal reserves of the country in next decades. However, the country is also in the process of becoming an EU Member State, hence, it is expected that the energy policies have to comply with the EU. Moreover, Turkey ratified Kyoto Protocol, thus the country should limit greenhouse gas emissions. Clean Coal, Carbon Capture and Storage (CCS) technologies are expected to become an important instrument for the mid-term reduction of CO2 emissions from coal-fired power plants. An alternative technique to the conventional CCS methods is CO2 sequestration by mineral carbonation. Turkey has significant resources of magnesium silicate minerals (olivine, serpentine) deposits which can be utilised in CO2 sequestration by mineral carbonation method.

Jan 1, 2011

By M. Pernot

A 12 m-deep excavation has to be perfomed in the Shanghai soft clay to install an underground electric substation. This article was originally intended to study the behaviour of the wall, the excavation bottom and the surrounding ground during the excavation. Since the works are behind schedule, and the data referring to the excavations are not, therefore, available, the article is limited to a presentation of the analysis methods that we envisaged for the study of the behaviour of the excavation.

Jan 1, 2010

By Luis Espinoza

La unidad minera Tintaya al igual que la Unidad Minera Antapaccay, son las operaciones de la división Perú de Xstrata Copper dedicados a la producción y comercialización de concentrado y cátodos de cobre. Sin embargo, la mina está en su última etapa de vida. En este sentido, surge el proyecto de integración de la unidad Antapaccay, donde se busca prolongar la vida útil de la mina y por consiguiente, el de la actividad económica minera en la provincia de Espinar. Por ello, el presente trabajo, describe los efectos de esta expansión de la explotación minera a través de la Unidad Minera Antapaccay que utiliza las instalaciones de Tintaya, manteniendo los planes de inversión social y el desarrollo económico local y regional.

Sep 21, 2013

By Ulf G. Gwildis

The Bright water Conveyance System includes 21 km of tunnels mined by two earth pressure balance Tunnel Boring Machines (TBMs) and two slurry TBMs. The probabilistic baseline approach defined in the Geotechnical Baseline Report (GBR) can representatively be verified by use of a comprehensive tracking system to identify face conditions that allows comparison with the baselines. The glacial geology includes a high lateral variation in soil types that, when combined with the pressurized face tunneling methods, creates challenges for documenting face conditions. Baseline tracking using spoil samples and TBM operational parameters provides information to document actual conditions and support resolution of differing site condition claims.

By P R. Denize, V S. Wein

A brief review of the Waipipi Iron Sands Limited company history and operations over the past ten years is made along with a summary of the benefits of this mining company to New Zealand. Land rehabilitation procedures in coastal dune lands are described in detail and brief mention is made of a study of animal health and copper uptake. The paper concludes with a summary of the increased emphasis on agronomy and restoration as the mining operation commences dredging in a better class of grazing land.

Jan 1, 1981

By S. Bellec, A. Berton

"Usually, steady state mass balances are used for the design of mineral processing plants. However, this tool does not take into account the impact of process inputs variability nor does it evaluate process transient behaviours between stationary states, such as mill start-up and shutdown. The use of advanced simulations enables the integration of dynamic behaviours in process design decision-making by highlighting situations that are undetectable by using only steady state mass balances. Applying these simulation tools to brown field projects allows the simulator performances to be calibrated and validated on actual plant data before it is used as a prediction tool for the modified plant.Three (3) simulators were implemented at the design stage of a major upgrade project for an ore processing plant in order to assess process behaviours under different production scenarios. These simulators were built to evaluate the impacts on major elements such as mine production, ore stockpile, concentrator production as well as water demand. A validation of individual equipment models was performed whenever sufficient measured data was available. The simulators were then used to study the impact of ore variability (grade, hardness, throughput), to assess day-to-day production special events, and to evaluate the true stockpiles live capacity.The use of a stochastic simulator for equipment sizing allowed a more precise sizing of many pieces of equipment and avoided important expenses in the fresh water pumping system. The dynamic simulator also confirmed that the water in place system would suffice, even in the most demanding production scenario. Finally, the stockpile simulator allowed an important production bottleneck to be quantified and then made possible the assessment of various practical solutions for the stockpiling-reclaiming issues.Post start-up, process data underlines the fact that using advanced simulation tools was useful to mitigate process-related risks associated to the plant expansion, showing generally accurate prediction and adequate equipment sizing, leading to smooth process commissioning. The presented methods are part of what is now routine in Soutex’s participation in both greenfield and brownfield projects."

Jan 1, 2015

Suggestions have been made at various times that there may be a recurrence of lodes similar to those at Kalgoorlie in the country to the south of the Golden Mile, but, so far as is known, there has been no geological evidence to support these suggestions apart from the possible extension of the younger quartz-dolerite greenstone in this direction.Geological mapping carried out by the writer in the Coolgardie district in 1946, provided some additional geological evidence to support this claim, and the ideas then held have since been expanded and are now considered to be sufficiently advanced to present them as concrete suggestions. As will be seen from the following pages, the critical area for lode prospecting is Hannan's Lake, where the basement rocks may include younger quartz dolerite greenstone, which, although perhaps distributed over a smaller area than at Kalgoorlie, could, on structural grounds, have a similar fracture system and similar ore deposition.There is little need to stress the importance discoveries in this area would have in prolonging the life of the field, and stimulating the post-war gold mining revival.Previous Work: Only the publications having a direct bearing on the preparation of this paper are given in the list of selected references, but the writer is very conscious of the fact that much other geological work has been carried out in the Kalgoorlie district since its discovery, by the W.A. Department of Mines, by mining companies, and others, all of which has contributed to the present knowledge of the field, and acknowledgment of the value of this work is given herewith. In presenting the suggestions in this paper a broad structural control of ore deposition is assumed, but this has already been established in other parts of the goldfields of Western Australia, including adjacent areas. In the early nineteen thirties, the Western Mining Corporation commenced work on the basis that there was a close relationship between geological structure and auriferous ore deposition, and a similar approach was first made by the Geological Survey of Western Australia in the South Yilgarn in 1935. These ideas were further developed during later surveys, particularly in the North Yilgarn and the Mount Margaret Goldfield.During the Coolgardie Survey in 1946, broad structural mapping was done in greater detail than before, and the structural ideas were implemented and further developed, leading to some success.Other work to which particular acknowledgment is given is that of Stiltwell, Gustafson and Miller, Forman, Prider and Finucane, at Kalgoorlie, and that of Honman in the Kalgoorlie-Coolgardie district, references to which are given at the end of this paper.Valuable constructive criticism of this paper has been given by Professor E. de C. Clarke and Dr. R. T. Prider, of the University of Western Australia.

Jan 1, 1950

By Paul W. Cleary

Keywords: Reactive pellets, CFD, Lagrangian SPH, Pyrometallurgy In several pyrometallurgical processes, reactive pellets are added to a melt. Heat is transferred to the pellets and reaction products such as gases, metal and slag are formed. For many pyrometallurgical processes traditional grid based CFD methods, such as using the Finite Element Method (FEM) and Finite Volume (or Control Volume methods), produce suitable predictions. However, the inclusion of solids in the bath represents significant challenges for these methods. Smoothed Particle Hydrodynamics (SPH), a Lagrangian simulation method, is able to simulate both the fluid component of the bath and any immersed solid materials, tracking the motion of these solids, and their interaction with the fluid, including gas generation. In this paper, we will summarize the key aspects of the SPH method and will show a series of structured examples illustrating the behavior of the different physics sub-systems that are used in the model of the overall system.

Jan 1, 2005

By Colin Lawrence, Michael S. Schultz

Due to the planned deepening of the NY Harbor, NYCEDC/NYCDEP is planning to replace two existing water lines between Brooklyn and Staten Island with one deeper water pipe. The crossing, just north of the Verrazanno Bridge is 1.75 miles long. The new pipeline will be tunneled using gasketed concreted segmented liners. Apressurized face machine will be used through the soft ground. This will be the first subaqueous application using this technology in New York City. This paper discusses the planning, design and risk issues associated with the crossing and the challenging soil conditions that resulted in the decision to use a pressurized face machine.

Jan 1, 2007

By M. Karmis, S. K. Weisiger

The traditional method for training personnel in the mining and other heavy industries has been face-to-face, either via a lecturer in a classroom or through an apprenticeship. With the advent of applications tools such as video, computers, and the Internet, however, a much broader range of training delivery methods is available. Especially exciting are the broad capabilities of multimedia packages that combine the best features of numerous delivery methods. Applying multimedia environments in training holds great potential, especially when there is considerable difficulty in reconstructing real training environments. The authors discuss various delivery methods currently used in training employees, including perceived advantages and disadvantages of those methods. The authors then discuss and evaluate current computer-based training efforts of the mining industry and present an example of a multimedia training tool.

Jan 1, 2001

By Gene Mattila, Ron Boyd

Introduction Rock bolting is a general term that encompasses pinning, roof bolting, rib bolting, and cable bolting. Rock bolting contributes the highest nonproductive cost and is the most significant safety risk in mining today. Total installed bolt costs are now more than $20 per bolt. Rebolting or repair work doubles this. And bolting accidents account for about 30% of all fatal and nonfatal lost time accidents. It is only logical, then, for the mine operator to install the highest quality anchors possible. Every bolt on the market - tensioned, untensioned, full contact, or point anchor - has designed capabilities in axial, shear, and fluctuating ground conditions. Bolts will provide a designed support if material specifications and installation procedures fall within the manufacturer's recommendations. This also assumes that there are no unexpected geological or operational changes. Proper material specifications and installation procedures should guarantee the mine operator a quality anchor. To help assure this, the Mine Safety and Health Administration (MSHA), the US Bureau of Mines (USBM), and the AMC Manufacturers group developed stringent ASTM materials standards. These govern mechanical point anchor bolts and bolts using threaded and nonthreaded rebar. There are also minimum standards that suppliers must comply with in the manufacture of frictional bolts. However, most frictional bolt standards are based on the manufacturer's own specifications. It would be impossible to set uniform regulations on frictional bolts. Each bolt provides support in a slightly different manner and thereby requires different material needs. Quality Control In any case, material quality can generally be assured through tight order specifications and periodic quality control checks. The problem with installing quality anchors does not solely lie with the material. It includes all the events that occur from the time a bolt leaves a manufacturer to the time it is installed. The anchoring ability of any major type bolt can be affected by transportation, storage, mechanical performance of installation equipment, installation demands of the operator, proper drilling accessories, and local geology. Table 1 and Fig. 1 document the negative events that can affect each bolt and the degree to which it can be affected. Drilling a hole of oversized diameter, for example, is an operator controlled factor. It will adversely affect most bolts. An over-sized diameter reduces, or even eliminates, the anchorage capability of a mechanical shell. It will reduce the support capacity of a split set to nearly nothing. And it will cause a partial or incomplete grouting around the resin bolt. Frequently, due to bit wear, holes are drilled undersized in diameter and may not be properly cleaned out. In this case, it will be difficult for the operator to push the mechanical shell into the hole, thereby causing him to drill another hole. In cases where the bolt is obviously not providing anchorage, operators will probably drill another hole and place another bolt. Rock Bolt Regulations It is the situations where a bolt is improperly installed in the hole, but gives the appearance of a good bolt, that are frightening. In fact, some safety officials and engineers believe that only 50% to 60% of installed bolts are working. These bolts cause irregular ground load transfers in other bolts and overload them. This causes hazardous situations and overstressing. It is these bolts that fail prematurely 200 to 255 mm (8 to 10 in.) behind the face and possibly contribute to the high accident rate. The government and several manufacturers recognized the need to check the integrity of rock bolts. These programs are in different stages today. Tight torque regulations have been established for mechanical

Jan 4, 1985

By Uusna S, Canning R. G, Goodheart B. A

The development of a process for removal of iron oxides from ilmenite is outlined whereby the Ti02 content of Western Australian ilmenites can be upgraded from 55 to approximately 90 per cent. In the first stage, the iron oxides are reduced with solid carbon (coal) to metallic iron. Experimental reductions were carried out in crucibles, a fluidized bed, and a small pilot plant rotary kiln. The reduced ilmenite was then agitated in aerated water, in the presenceof catalysts, so that the iron "rusted" away from the ilmenite grains and the precipitated iron oxide was easily separable by decantation.The influence of variables on the rates of reduction and oxidation are discussed. The oxidation rate was examined for both the physical oxygen transfer characteristics and electrochemically by reference to Pourbaix diagrams, in which redox potential is plotted against solution pH.The upgraded ilmenite is expected to be an attractive material for pigment manufacture, and the iron oxide has prospects of being a marketable by-product. The process may possibly be applied to other ores.INTRODUCTIONThere are extensive deposits of ilmenitic beach sands, Le. iron titanium oxides of the general formula FeTi03, 'occurring in the lower south-west portion of Western Australia, and although there has been considerable commercial development, local producers face keen competition on a freight-cost basis. Thus the removal of the unwanted iron oxide constituent would have the double advantage of reducing the freight differential and presenting a more attractivematerial to pigment manufacturers.

Jan 1, 1965

By H M. Ahmed, W S. Dunbar

Construction of cave mining systems requires significant capital expenditure and long-term commitment of human, equipment and material resources before production commences. Risks and uncertainties of these large-scale mining projects are significantly higher than for small-scale projects. This is due to the complexity and interactions of the construction schedule components and the large scale and uniqueness of such projects. One way to successfully manage construction uncertainties that would lead to schedule delays is to include a reasonable cost contingency in the budget estimation. A real options approach based on the least-squares Monte Carlo (LSM) method is used to estimate cost contingency associated with schedule uncertainty in mass mining projects. Cost contingency is estimated as the cost of potential project crashing (acceleration) decisions, which pays for not extending the schedule. While such a significant undertaking is expected to be subject to some delays, these can have an enormous impact on the economic value of such projects. The value of the crashing option was explicitly formalised into the process of valuation, as it is assumed to be a single option being considered in the valuation at every decision point prior to the construction completion date. As a part of the proposed method, a stochastic function for the percentage of remaining scope of work for the remaining duration of the entire project was integrated into a framework of numerical simulations. This ensured that this function can implicitly account for sources of schedule uncertainties for projects represented by multiple and overlapping work packages. The LSM method was applied to a real case scenario in an operating block cave mine, with modified scale and features. The results yielded by the LSM method indicated that significant changes in capital budget allocation stem from variation in a contractor’s risk perception and confidence level of estimated delays.CITATION:Ahmed, H M and Dunbar, W S, 2016. Budget estimation and contingency allocation of block cave construction using least-squares Monte Carlo real options, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 801–808 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

The C.S.I.R.O. acid alumina process employs the essential steps of digestion, hydrolysis and calcination to produce pure alumina from ores too high in silica or too low in grade for the Bayer process. The two latter stages have been described in some detail previously but the digestion stage requires separate discussion since ores vary widely in composition and reactivity. Kaolinitic clays require roasting to 800°C to render the alumina soluble in the 11 per cent sulphuric acid used in the process while some ferruginous laterites require roasting to reduce the reactivity of iron minerals.The iron content of pregnant solutions is kept at a low figure by digesting at temperatures where the solubilities of ferric oxide or basic ferric sulphates are small. A two-stage, counter-current digestion is necessary to extract a high percentage of alumina from the ores and to produce a basic pregnant liquor with an SO3 : AI 203 ratio of 1'\1 suitable for high temperature hydrolysis. The second stage of digestion, called the modification stage, treats slightly acid liquors with excess of ore in the temperature range 1200-1400C.The first stage operates at 170°-1900C to extract further alumina from modification residues, using recycled acid obtained from later steps of the process. Both temperature ranges are critical for economic operation and for proper control of the iron content of solutions. In batch experiments, 30 min is regarded as a suitable retention time for digestion and modification; ores which require much longer than this are less suitable for the process. Impurities such as silica, and titanium and vanadium oxides are discarded in the residue along with iron oxide, and do not contaminate the final product. Bivalent metallic sulphates such as MgSO4, can build up in the circuit to a very considerable degree without affecting product purity.Comparison with other processes shows that the C.S.I.R.O. process is superior for control of contamination by iron, which is the major problem in acid processes. The pure intermediate product (3Al203.4S03.9H20) is also more convenient for calcination to alumina than the hydrated aluminium sulphate usually recovered in other processes. Detailed cost comparisons must await pilot-plant evaluation of the C.S.LR.O process.

Jan 1, 1964

By A. J. Williams

"Conventional base metal milling practice normally consists of crushing, grinding and cyclone classification followed by flotation. It is the authors' belief that the commencement of flotation after cyclone classification leads to inferior metallurgical results and that implementation of flotation of grinding mill discharges can result in increased recovery due to reduced overgrinding, reduced activation of contaminating minerals and improved dewatering circuit results due to the production of coarser concentrates.The concept of recovering minerals from the discharge of grinding mills is not new! Gold concentrators have utilized jigs and flotation cells while iron ore plants have employed magnetic separators to recover gold and magnetite respectively from the discharge of grinding mills. More recently, a Reichert cone has been used to recover sulphide and oxide base metal minerals from screened rod mill discharge. 1To the authors' knowledge, the first application of flotation of base metal minerals from the discharge of a production plant grinding mill was at the Lake Dufault concentrator of Corpor'1tion Falcon bridge Copper. Located 10 miles north of Noranda, Quebec the Lake Dufault concentrator commenced operations in August, 1964.The installation of flot11tion cells in the Lake Dufault grinding circuit proved so successful that an identical system was installed in the Manibridge concentrator of Falconbridge Nickel Mines Limited. Located 90 miles southwest of Thompson, Manitoba the Mamibridge concentrator commenced operations in June, 1971 and due to exhaustion of economic ore reserves discontinued production in May 1977."

Jan 1, 1984

By Fengyu Ren, Ruslan Puscasu, Kunpeng Yu, Gideon Chitombo, Liangliang Kang

Weak rock mass and poor flow of material can cause excessive ore loss and dilution in sublevel caving. This paper proposes a method to establish design parameters for an inclined deposit within a weak rock mass and evaluates its effectiveness through a case study. In order to solve the problem of low production capacity and poor safety conditions of sublevel caving mining at the Yingfangzi silver mine in China and to ensure a smooth production from the refractory ore body, it is necessary to select appropriate stope structure parameters. Based on random medium theory of gravity flow and the improved equation of ore discharge in random medium, an end wall drawing experiment is carried out to determine the optimum design and flow parameters. It was observed from the experiment that, due to the influence of the randomness of particle movement, there is a mismatch in the flow parameter measurement. The flow characteristics and distribution of the marker particles are different from that of the tested particles resulting in large drawbody shape distortion. The study finds that the flow parameters obtained by the new method are more practical and account for drawpoint width and recommends that the new method for determining the sublevel stope height is used when the drawbody is a non-standard ellipsoid. The outcomes have shown a significant reduction in the dilution and improvement in the recovery rates, and the safety and efficiency of mining have been greatly improved.

With the exhaustion of orebodies close to the main haulage shaft of the Emperor mine, an increased rate of development, aimed at earlier investigation of values disclosed by exploration drill holes has been attained with an overall reduction in unit costs.This paper describes the techniques used in rates of advance up to and exceeding 1,000 ft per 28-day period.

Jan 1, 1966

By Vinay Kumar Agrawal, Rama Nath Praharaj

IMFA Group is the largest producer of Charge chrome not only in India but also in Asia. This Group has plants situated at Therubali and at Choudwar. They also have a Thermal power plant at Choudwar which not only caters to the power requirement of Choudwar plant but also supplies power to Therubali. The plants are fed for Chromite ore through the captive mines namely Nuasahi Chromite mines (40.47 Ha) , Bangur Chromite mines(37.34Ha), Sukinda chromite mines (116.76 Ha), Mahagiri Chromite Mine(73.777 Ha) and Chingudipal Chromite mines (26.62 Ha). Nuasahi Chromite Mine, which is situated in Keonjhar district, is an underground mine and is based upon best technological advancements in the industry. The underground mining operation is certified under ISO-9002, ISO-14001and OHSAS 18001. This not only shows the concern for the quality, environment but also for the health of the employees. The Nuashahi is the first chromite mine to backfill the opencast excavations created during the last 50 years and carry out the production from underground area below the opencast workings. This paper deals with the state of art technology of sub-level open stopping in thin ore bodies. The under-ground mine openings was started in the year 1997. In next four years the production of chromite from underground was started.(2001). At present the mine is in a good shape with several running stopes. Today it is producing around 10,000 Mt per month of chromite. The development of the mine is carried out with an average of 200 mtr per month of tunneling. The mine is having a mechanical ventilator having a capacity of24000 M3 per hour at 50mm water gauge, thus feeding sufficient air for the persons working in underground. The mine is being dewatered through a most modern positive suction sump, having a capacity of 500 cum and operated with 120 HP pumps. After commissioning of this sump in the year 2003, the mine has taken a quantum jump in production with remarkable saving in power consumption.

Jan 1, 2007