Search Documents

By E. C. L. Cardoso

Hydrocarbon polymers, as PP, made from cheap petrochemical feedstock are important in many branches of industry. However, they have an undesirable influence on the environment and cause problems due to waste deposition and utilization. Polymeric materials composites account for an estimated from 20 to 30% of total volume of solid waste disposed. Thus, there is a tendency to substitute such polymers by those ones that undergo biodegradable processes. Polypropylene (PP) is a commodity, with high melting point, high chemical resistance, low density, with a balance between physical and mechanical properties and easy processing at low cost. Nevertheless, PP shows limitations for some special applications in automotive industry and civil construction. In order to minimize this deficiency, related to rheological behavior of polymer melt, especially referring to viscosity in processing temperature, a 50% mixture with HMSPP (High melt Strength Polypropylene) was used. PP/HMSPP was blended with 10, 15, 30 and 50% of natural (sugarcane bagasse) and synthetic polymers (PHB and PLA) aiming to partially biodegradable materials. The admixtures were subjected to gamma-irradiation at 50, 100, 150 and 200 kGy and then further assessed by mechanical tests in order to evaluate their degradability.

Jan 1, 2015

By R. Hurman Eric

Within the Ag-Pb-S ternary system, the boundaries of the immiscibility region together with the tie-line distributions were re-established at 925°C by the equilibrium-quenching technique where samples were kept in evacuated and sealed silica capsules. Activities of Pb were measured by the dew-point method along the Ag-Pb binary at 925°C, 1100° and l200°C, positive deviations were observed and the results were modeled by the Krupkowski formalism. Activities of Ag, Pb, and S, along the ternary miscibility gap were calculated at 925°C by utilizing the boundaries binary thermodynamics, phase equilibria and tie-lines. Activities of PbS within the pseudobinary Ag2S-PbS mattes were also measured by the dew-point technique and the results were again modeled by the Krupkowski formation where negative deviations were observed.

Jan 1, 2003

By R. Hurman Eric

Within the Ag-Pb-S ternary system, the boundaries of the immiscibility region together with the tie-line distributions were re-established at 925°C by the equilibrium-quenching technique where samples were kept in evacuated and sealed silica capsules. Activities of Pb were measured by the dew-point method along the Ag-Pb binary at 925°C, 1100° and 1200°C. positive deviations were observed and the results were modeled by the Krupkowski formalism. Activities of Ag, Pb, and S, along the ternary miscibility gap were calculated at 925°C by utilizing the boundaries binary thermodynamics, phase equilibria and tie-lines. Activities of PbS within the pseudobinary Ag2S-PbS mattes were also measured by the dew-point technique and the results were again modeled by the Krupkowski formation Where negative deviations were observed.

Jan 1, 2003

By Xie Zhang, Jiang Diao, Xin Qiu, Lu Jiang, Bing Xie, Hong-Yi Li

"Duplex converter process, in which the first converter is used for removing phosphorus from hot metal (De-P), is an important way to produce low P-content and ultra-low P-content steels. In order to improve phosphorization removal and formation of slag with high basicity at relatively low temperature during dephosphorization converter process, effects of temperature, silicon content in hot metal and varied compositions of the De-P converter slag on phosphorus distribution between the slag and hot metal were investigated with thermodynamic calculations and by laboratory scale experiments in present work. Results showed that phosphorus distribution ratio between slag and metal was varied in 10.6~26.6 when basicity of the slag was in the range of 1.5~2.1 at 1370, and the distribution ratio was increased with increasing basicity and Fe10 content in the slag.IntroductionIt is known that phosphorus exists in steel in the form of solid solution, which can significantly improve strength and hardness of steel at room temperature. However, the plasticity and toughness of steel, especially the low temperature plasticity is sharply reduced and leads to high ductile-brittle transition temperature. This phenomenon is commonly known as cold brittleness of steel [1~3]. Hence, phosphorus should be removed as much as possible in the steelmaking process, because it is generally harmful to the iron and steel products."

Jan 1, 2013

By Xun Hu, Jian Pan, Hongbin Yu, Deqing Zhu, Yanhong Luo

Lump ores are one kind of important burdens for blast furnace (BF), their metallurgical properties have significant influence on BF performance. In this paper, the relationships between the mineralogy of five natural lump ores and the metallurgical performance have been studied. The mineralogy study includes mineral compositions, microstructure and porosity, and the metallurgical performance covers reducibility index (RI), low-temperature reduction degradation index (RDI) and decrepitation index (DI). The results show that the complex lump containing hematite, and goethite has better overall metallurgical performance. For single lump, the RI of goetihte ores is higher, the RDI and the DI is strongly influenced by porosity. The hematite and magnetite ores have good anti-decrepitation and anti-RDI, but generally the RI is lower due to lower porosity, and the RI is related to the grain size, the smaller grain size is, the better reduction will be.

Jan 1, 2015

By M. Fujikawa, S. Goto, M. Nishikawa

"The semi-pilot scale plant for injection smelting of zinc calcine was operated under the committee of Joint Research Organization of Injection Metallurgy. The capacity of the plant is 10 ton metallic zinc per day. The plant was designed by the resul ts of basic and bench scale tests of the capacity of 1 ton metallic zinc per day which was published at ""Zinc '85"". The equipments of the plants, operational conditions, results of the operation such as recovery of zinc in injection furnace and condenser, combustion rate of powdered coke and consumption of energy in this process are presented in this paper. The results of the study of the feasibility of the commercial plant of 100,000 ton zinc per year by the injection smelting are also discussed in the paper. IntroductionThe research committee of new smelting process of zinc by injection was established in 1981 under the finantial support of Mining Promoting Foundation of Japan. Six zinc producing companies joined in this organization. The price of zinc was very low at that time and the energy cost, especially, cost of electric power in Japan was extremely high. Invention of a new economical process for zinc extraction had been stronglydesired. The author proposed a injection smelting of zinc as a economical process in energy saving after a calculation of thermodynamical equilibrium and heat balance(1 )(2).The research committee has been studying the injection process since 1981. The small basic experiment by using a crucible furnace was carried out from October 1981 to March 1983 and the reaction of reduction of calcine by injection smelting was ascertained (2). Vaporizatipon of zinc and behaviours of impurities were examined. After the basic experiment, the bench scale test with the production capacity of zinc of 1 ton per day was carried on from November 1983 to October 1984.The bench scale tests were carried out to obtain the proper design of feeding devices of calcines and coke into a furnace and also to obtain fundamental data for enlargement of this smelting process(3,4). The recovery of metallic zinc in this small equipments was about 50% and main loss of zinc was formation of dross in the condenser."

Jan 1, 1988

By R. Elliott, H. Bayati

"Effect of time and temperature on microstructure and mechanical properties of an austempered ductile iron, ADI, of composition 3.6%C, 2.6%Si, 0.4%Cu, 0.2%Mn are reported. Xray analysis and. microstructural observations indicate that lowering the working temperature, aging temperature, increases the lifetime of ADI significantly. Results show· that lowering the aging temperature increases the strength and reduces the ductility of ADI. DSC traces for ADI austempered at 340°C are presented. Comparison of the DSC analysis and kinetic measurements demonstrates that the DSC traces can be· used to predict the life time of ADI successfully.IntroductionAustempered ductile iron, ADI, is one of the most significant developments in cast iron technology over the past two decades. Outstanding properties of high yield, ultimate strength, ductility, fatigue and wear· resistance make ADI suitable for a range of applications including gears, connecting rods, crankshafts and agriculture machine components. The austempering reaction in cast iron occurs in two stages, Fig. I, in contrast to the single stage reaction in steel. In stage I the relatively low carbon austenite produced during austenitising transforms into ferritic plates and high carbon austenite, a metastable structure called·ausferrite. The high carbon ailstenite and supersaturated ferrite produced in stage I decompose into ferrite and carbide in stage II: to form a structure similar to the bainitic structure in steel. This behaviour exposes a well-defined processing window, t1 - t2, over which the maximum amount of ausferrite is produced, Figure 1. Whereas the bainitic structure determines the properties of austempered steel, ADI properties are mainly affected by volume fraction of retained austenite (VRA), austenite carbon content (ACC), unreacted or martensite volume fraction (UA V), compositiori and amount of carbides, and morphology of ferritic plates[l,2]. Due to the detrimental .effect of martensite and carbides on properties of ADI, an ideal structure of ADI consists only of ausferrite [l,2]. Thus, it is common to determine the processing window for each austempering treatment in order to identify the optimized austempering time. Decomposition of austenite (stage II) signals the end of the life time for an ADI component, therefore, the aging behaviour of ADI at different working conditions can be studied by determining the t2."

Jan 1, 2000

By Eleazar Salinas R., Miguel Perez L., J. Cesar Juarez T., Martin Reyes P., Eduardo Cerecedo S., Isauro Rivera L., Francisco Patino C., Juan Hernández A.

"A complete characterization of burrows from Mining district of Pachuca - Real del Monte, in Hidalgo state Mexico, was done. These kind of residues had not been formally characterized, founding an average chemical composition of 70.43 % wt. of Si02, 7.032 % wt. of Ah03, 2.69 % wt. of Fe20 3, 0.70 % wt. of Mn, 3.98 % wt. ofK20, 3.34 % wt. of CaO, 2.50 % wt. ofNa20, 1.01 % wt. of MgO, 0.26 % wt. of Ti02, 0.04 % wt. of Zn, 0.026 % wt. of Pb, 56 g/ton of Ag and 0.6 g/ton of Au; In the same way, the residues present as majority mineralogical phases the following: Quartz, Berlinite, Orthoclase, Feldspar, Anorthoclase and Calcite. By the other hand, joint with the big volume that present these residues and the chemical and mineralogical characteristics, these materials or sub - products can be used for production of ceramics, into mixes forming some materials for architecture (bricks, blocks, and tiles), refractory bricks, in the production of cement and to get some metallic values such as gold and silver involved in these residues.IntroductionActually the mining residues in Hidalgo State, Mexico are the result of more tan 500 years of mining, leading so a great volume of deposits, which we can classify in different types, among the most communes we have: Acid Mining Waters, Waters of solid transport and elements in the form of radicals, deposits of abandoned minerals without processing, and mining wastes of processed minerals known as burrows or dumps, being these the most abundant in the Hidalgo State [1-4].Form the metallurgical point of view, it is known that a characterization study if fundamental to find the viability of reuse of these kind of residues, leading so an additional use and the opportunity of get an alternative use into several industrial processes, due to its contents of oxides of silicon, iron, aluminum, calcium, sodium and potassium, principally, besides of its mineralogy and distribution of chemical elements into its primary and secondary phases [ 1-2, 5- 6]."

Jan 1, 2011

By Chao Li, Lim Hongxu, Yuyue Wang, Xie Yang

"A intergrated process of sulfuric acid leaching, sodium chloride leaching, lead chloride crystallization, lead hydroxide synthesis and roasting was carried out for the recovery of lead, cadmium, copper and zinc from lead smelting dust containing various metals. The results showed that the separation of cadmium, zinc and copper from dust could be obtained after sulfuric acid leaching and corresponding leaching rate were 92.12%, 90.25% and 88.26% respectively. The subsequent sodium chloride leaching carried out for lead with optimized parameters as: sodium chloride concentration 250g/L, leaching temperature 90°C, leaching time 2h, pulp density 33g/L, 0.12mol/L CaCh; The lead compounds crystallization rate reached 86.67%, and then transferred into mPbO·nH2O, the product of 98.66% ß-PbO could be obtained through roasting under 502°C. In the end, a feasible method of ß-PbO preparation from lead containing dust was put forward.IntroductionThe pyro-metallurgy flue dust from smelting lead activities are often stockpiled and pose potential environmental risks due to the heavy toxic elements, such as Pb, Cd, As, Cu, Cl, and Zn which are contained in the dust. With the rapid depletion of rich ore resources in recent years, it has become increasingly more financially attractive to recover valuable metals from previously stockpiled dust, while simultaneously reducing the potential of environmental pollution from toxic elements contained in the dust. Nowadays, pyro-metallurgical and hydrometallurgical routes or both combined methods can be developed to treat secondary materials such as lead ash, leach residues etc. By comparison the hydrometallurgical processes are often considered more eco-friendly.Some chloride leaching processes for recovering lead have been employed using either NaCl, or MgC2 and CaCl2, or FeCl3 [1] The effectiveness of the brine leaching method is based on the formation of complex metal chlorides in concentrated chloride solutions [2] Similarly, Other metals such as zinc, cadmium and copper contained in the flue dust are often treated with sulfuric acid, hydrochloric acid, ammonium solution and sodium hydroxide etc. as lixiviants [3] The metals from leach solutions thus has been obtained by precipitation, ion exchange, solvent extraction or replacement [4]"

Jan 1, 2014

By C. Takano

The integrated iron and steelmaking industry generates large amounts and many types of solid dusts and sludge, at different phases of the production. Within these are: sludge of the Blast Furnace; coke fines; fine and coarse fractions from oxygen converters; sludge from water treatment at rolling mill unit; and others. In this paper the above dusts and sludge were physically and chemically characterized. The obtained results allowed defining self-reducing pellets using these materials. The high temperature behavior of the pellets were evaluated. Good results, with no decrepitation and swelling, and high yield of reduction, show that it is feasible to recycle them, as self-reducing pellets, in oxygen steelmaking converter.

Jan 1, 2001

By W. G. Davenport

The remainder of this book develops and uses mass and heat balances to describe steady"state flash smelting. Its objectives are to: a) describe the many ways a flash furnace operator can produce specified products, e,g. 65% eu matte, 35% SiOz slag, 1500 K (b) determine the oxygen, air, flux and hydrocarbon fuel requirements of each method (c) show how the flash furnace can be controlled to give specified products with varying feed compositions (d) suggest how the flash furnace operator can maximize profitability while producing specified products. This chapter develops the basiC heat and mass balance equations of steady-state ?flash smelting. It then adapts the equations to industrial feed materials .and products. Lastly it determines the amounts of oxygen and flux needed to produce molten matte and 35% SiOz slag from chalcopyrite concentrate in an Inco oxygen flash furnace,

Jan 1, 2001

By C. P. Snyman

Three independent methods of coal classification can be distinguished, namely on the basis of grade, type and rank. The latter two can be determined accurately and unambiguously only by means of microscopical techniques. These three independent variables affect all the coal properties and therefore also the technological behaviour of a particular coal. The influence of the inorganic constituents of coal on the fusibility of the ash and on the length of the slag, and also on fouling and slagging, is discussed. The fractionation of the ash-forming constituents during combustion and gasification of pulverised coal shows that fouling and slagging are not related directly to the fusibility and composition of ash of the coal as a whole. The results of combustion experiments using a drop furnace technique indicate that the ignition temperatures of the light volatiles in the coal, and of the formed char, as well as the burn-out time of the char are more dependent on the rank than on the type or grade of the original coal. High-ash coals, however, apparently ignite at lower temperatures and are more reactive than low-ash coals of similar type and rank. The surface properties of coal, which are important in froth flotation and oil agglomeration, correlate well with the inherent moisture content (and by inference with the heat of wetting and the calorific value) and therefore with the type and rank of the coal. In coal exploration, variations of rank offer the possibility of predicting the presence of an intrusion near the seam, thus contributing to more effective exploration and mine planning.

Jan 1, 1991

By Bruno Augusto Batista Ribeiro, Felipe Terra Elias, Wagner Moulin Silva

In the pyrometallurgical production of copper from its sulfides, converting in the Peirce Smith (P-S) Converter is still the most widespread method to obtain white metal and blister copper from the matte. Despite the fact of being a century-old process, it is still possible to achieve improvements in the process, by the use of modern tools, one of the most valuable being numerical calculation and computer-aided simulation. The present study presents three cases in which the angle for the gas injection and the number of working tuyeres are changed during the slag blow phase of the converting process. It was noticed that a decrease of the number of tuyeres, followed by an increase in the injection gas velocity, results in improved reaction volume and less stress to the refractory lining. However, an increase in the amount of copper lost to the slag as oxide is likely to occur.

Jan 1, 2014

By R. Hamar, G. Lamanthe

"To realize complex shaped pieces, like turbine blades, superalloys are cast with the lost-wax process. The end properties of these parts depend upon their microstructure as well as upon the occurence of casting defects such as micropores and hot tears. Such features are governed by the local solidification conditions which may be describe by the calculation of thermal transfers between alloy and mould. It needs the evaluation of numerous parameters which are fitted from experimental measurements in real castings. In further simulations, any parameter may be changed, in order to determine its influence. Such a single modification is quite impossible to realize in real castings, which shows that numerical modeling is a very good way to study casting processes.This modeling technique of casting is applied here to the real study of a typical low pressure turbine blade of a civil engine.IntroductionAircraft engine manufacturers use superalloys to produce turbine blades. They have to obtain a given microstructure and to avoid solidification defects to give good mechanical properties to theirs castings. For example, microporosity is induced by a large shrinkage that cannot be completely fed with the remaining liquid alloy .The optimization of casting processes needs a good Knowledge of the solidification process, that must be controlled at every place in the casting, and at every time of its freezing. Material and heat transfers that occur during the solidification, can be estimated from rather complex calculations. To model these physical phenomena, the evaluation of many parameters must be made. In this aim, some casting experiments are fitted with numerous thermal captors. The identification of experimental and computed thermograms let us estimate these parameters.A long-range scientific cooperation between SNECMA and INPG has enabled the realization of such studies on this topic. From all of them, this paper describes an experimental and computed investigation which has been led on a typical low pressure turbine blade of a civil engine."

Jan 1, 1986

By Tom Marttila

During the last few years, when a new tankhouse or a major modernization has been planned, automatic or semiautomatic crane and grab systems have at least been considered. It seems that in the future tankhouse managers for new, modernized and even old tankhouses will be looking for a proven and reliable system for automatically moving and positioning electrode loads in the tankhouse and in storage areas. In this paper, we will describe the Wenmec solution for automatic electrode handling. The advantages of automatic handling and very accurate electrode positioning will be discussed, and the way Wenmec has solved the problems in mechanical construction and in automatic, accurate and reliable positioning will be presented.

Jan 1, 1990

By Ali Hasham

Reduction rates of FeO in CaO-SiO2-Al2O3 slags by Fe-C melts have been investigated experimentally at 1723 K. The rates were estimated using experimentally determined CO(g) evolution rates. Flash X-ray images were employed to visualize the behavior of the melt-slag interface during the reactions. The influence of melt interface was examined by conducting two types of experiments - (i) dropping one (or several) Fe-C droplet(s) weighing 2 g into the molten slag bath, and (ii) dropping a small amount (10-30 g) of slag onto a Fe-C melt weighing 400 g. The rates from both types of experiments were compared and analyzed to determine the rate limiting steps. It was established that neither the carbon transport in the Fe-C melt, nor the transport of gas species in the gas film adjacent to Fe-C melt was responsible in limiting the reaction rate. It is possible that the slag phase mass transport may be controlling the initial reduction rate in the droplet experiments. However, a, different mechanism was responsible in limiting the reduction reaction when the overall %C in the droplets fell to about 2-3.

Jan 1, 1992

By Afrodite Ntziouni, Vassilia Kasselouri – Rigopoulou, Athanasia Kyritsi, Konstantinos N. Pistiolas, Stamatia Gavela, Konstantinos Kordatos, Lazaros Iliadis

"The present study deals with the production and characterization of rice husk ash (RHA) and its use in the synthesis of zeolite of type ZSM-5. Rice husk was combusted in various temperatures with aim to find the suitable conditions for the production of amorphous silica. The resulted amorphous silica ash was then utilized as a starting material for the synthesis of ZSM-5 zeolite using the low temperature and atmospheric pressure process. The method led successfully to the synthesis of highly siliceous zeolite of type ZSM-5. The produced material was characterized using x-ray diffraction (XRD) and scanning electron microscopy (SEM).IntroductionRice husk is a major by-product of the rice-milling industries and it is usually used as a fuel for steam generation due to its high calorific power. During its combustion, rice husk ash (RHA) is produced. Knowing that the annual rice world production is over 615 million tons (2005), thus resulting in a potential production of more than 22 million tons of RHA [1], it can be understood that the RHA disposal is a crucial issue towards the environmental protection. However, due to the high silica content, RHA can be used as an alternative cheap source of silica for many uses, including as filler in polymers [2], concrete [3] and synthesis of zeolites [4-7].The burning of rice husk in air results in the formation of RHA with content in SiO2 that varies from 87 to 97% depending on the burning conditions, the rice variety, the climate and the geographic area [8]. Some small amounts of inorganic impurities are always present in the ash along with unburned carbon. The unburned carbon can be removed from the ash by further heating treatments in high temperatures, but this usually leads to the crystallization of the amorphous silica to cristobalite and/or tridymite [9]. The crystallization of the contained silica of the ash is also occurred when the burning conditions of husk are uncontrolled [10]. This crystallization is a disadvantage towards the preparation of silicon based materials, because the silica ash is rendered inactive in its crystalline form [11]."

Jan 1, 2008

By Claudio Toro, Alex Moyano, Jonkion Font, Carlos Caballero, Pedro Morales

"Codelco-Chile in the last decade has carried out industrially-oriented research as an alternative to the traditional batch-type converting process. In a first stage carried out preliminary evaluations in a rearranged Peirce Smith (PS) converter, and then an exploratory test in a “Convertidor Teniente” (Teniente converter, TC) for the Codelco-Chile Continuous Converting Process. However, the validation test for this process in the TC was delayed up to the second quarter of 2007 where the validation studies were done satisfactorily.Thus, the objective of this paper is to present the results of the campaign tests validating the Codelco-Chile Continuous Converting Process in the TC1 of the Codelco Norte smelter.The results of charging the solid or liquid matte or high grade matte (“white metal”) by Garrgun, or by mouth of the 22 m x 5 m TC1 are presented. Some features of the industrially validated process are discussed, and the pilot test results of the matte injection are also presented."

Jan 1, 2009

By Flavio Begazo, William A. Enrico

"Southern Peru Copper Corporation's Ilo Refinery, the largest in Peru, began operations in 1975 with a production capacity of 165,000 stpy. Southern Peru bought the Refinery from the state owned Minero Peru SA on June 1, 1994.The Refinery processes blister from Southern Peru's I/o Smelter. Blister copper is processed in an anode plant equipped with two 365 st tilting reverberatory furnaces, a 26 mold casting wheel and an anode press machine. Copper is electrorefined in a tank house equipped with 768 commercial cells, 44 stripper cells, and 40 liberator cells, utilizing two electrolyte circuits and a 21,000 Ampere rectifier.During 1989 through 1994 a program for improving productivity was carried out by increasing the number of cells and increasing current density to the total rectifier capacity. As a result, a capacity 215,000 stpy of refined copper, 2 million tr. oz silver and 6,000 tr. oz gold per year was achieved. In 1994 Southern Peru announced plans to increase capacity to 250,000 stpy of cathode with a US$ 18 million investment and a US$ 2 million investment in environmental improvement projects, as part of the purchase agreement with the Peruvian government.This paper outlines the scope of the SPCC lio Refinery modernization and environmental program. It describes the implementation of the Electrolytic Plant expansion based on instaliation of polymer concrete cells, a new rectifier, a new selenium roaster and a Precious Metal Plant upgrades."

Jan 1, 1997

By S. V. Cherty

The utilization of natural gas in non-ferrous industries during smelting and refining stages of copper , aluminum, zinc and lead was studied. The total amount of nonelectrical energy consumed in the production of zinc, copper, lead and aluminium, are 96.5% ,93%,92%, and 6 % respectively. It is calculated that 9.45 wt %of air of stoichiometric amount can be substituted by natural gas to the total air input in the nonelectrical energy utilization processes. The results showed that the non electrical energy may be substituted to an amount of 71 % ,52 % ,35 % ,32 % ,and 26% ,in the production of lead, aluminium (plates, foils) copper, aluminium, zinc, respectivelly. Similar calculations are carried out in terms of energy in Btu for the total production of non-ferrous metals in the U.S. It shows that 51.866~106 millions of Btu of nonelectrical energy can be substituted by 54.58~106 cu. ft of natural gas. Finally, the substitution of non electrical energy in terms of equivalent coal energy is discussed. 1t is shown that total non electrical energy is equal to 1.852 million tones of coal .If this 1.852 million tones of coal is replaced by natural gas, a total savings of 22.14 million dollars are achieved. The total or partial substitution of coal by the natural gas in the existing industrial processes and modification of redesigning the processes is discussed.

Jan 1, 1993