Search Documents

By F. E. Pawlek

Copper concentrates can be comminuted in an attritor within a very short time to a particle size of 1 - 0.1 um. Addition of sodium hydroxide enhances commninution. The concentrates, suspended only in water, can be completely dissolved under oxygen over pressure and temperatures ranging from 120 - 180°C (248 - 356°F), because the surface area of the concentrate has been significantly increased by the ultra fine grinding. Addi¬tion of a small amount of silver ions to leach liquor containing sulfuric acid acted as a catalyst for the dissolution of chalcopyrite, because of the formation of local elements on the surface. The addition of C1- ions was also catalytically very effective. With this method it is possible to completely dissolve the copper contained in chalcopyrite concentrates after ultra fine grinding within 30 min at 110°C (230°F) under an oxygen partial pressure of 1 atm (14 psig). Several flowsheets demonstrate the industrial feasibility.

Jan 1, 1976

By Elias Rigopoulos

In the present study the reductive behavior of dust from the rotary kilns (RK), in ferronickel production from nickeliferous Greek laterites, is investigated. The study concerns dust of various origins (washing towers, electrostatic filters, polycyclones) and pellets made from the dust. Reducibility was studied in the temperature range of 700 °C to 850 °C in a laboratory tube furnace. Experimental results showed that reduction degree increases with temperature up to about 800 °C. The rate of reduction is great during the first minutes, giving a reduction degree R% equal to about 25%, in only a few minutes. After this, the rate is decreasing until it diminishes to zero after about 10-20 minutes of reaction. Maximum reduction degree achieved is 26 to 28%. Rates and reduction degrees at various temperatures are higher for the dust samples than those of the respective pellet samples. Keywords: Ferronickel, metallurgy, laterites, pellets, reduction

Jan 1, 2004

By Burcu Ertug, Necip Ünlü

"On average, one out of two glass bottles coming on to the market is provided by recycling processes in Europe. Glass recycling has been started by the early of 1970s in Turkey, and the recycling amount has been reached to 70 thousand tons recently, while 4.2 million tons which represents only 25 percent of total glass manufactured, is the amount of glass collected annually for recycling in the world. The glass recycle process basically involves collecting, sorting, then crushing and grinding after which glass cullet is produced as the secondary raw material. Removing of the contaminants from the glass cullet, and then melting are the next steps. In this study, recent developments of 100% recyclable without any deterioration in quality, and never decomposable glass, are discussed detailed in terms of glass production processes.1.IntroductionIn many countries, waste glass constitutes a large proportion of solid wastes, and recycling the glass is a major environmental problem all over the world [1]. Among the diverse types of waste, glass is one of the most valuable recycling materials because it can be revived and recycled completely and hardly decomposes [2]. Between 80% and 85% of the mass output from the worldwide glass industry is either in the form of containers for the food, beverage, and pharmaceutical industries, or flat glass for building construction or for motor vehicle manufacture. Other product segments, whilst only constituting about 15% of the mass output, produce high value technical and consumer products by comparison with container and flat glass [3].In the present study, the recycling of Liquid Crystal Display (LCD), Cathode Ray Tubes (CRT) and Printed Circuit Boards (PCB) were examined. The production of glasses and glass-ceramics from glass cullet, synthesis of different compounds from recycled glass were other subjects of interest. The use of recycled glass for construction industry and using glass as aggregate were emphasized. Finally the recovery of glass fibers were investigated."

Jan 1, 2012

By Florian Kongoli

Converters have been playing an important role in the extraction and processing of metals ever since the first type of converter was invented about 100 years ago. Historically their operation has been mainly based on the experience of talented operators rather than on strict control and optimization technologies. However, in the new realities of unavoidable necessity to increase productivity and in the conditions of diversification of primary materials from various geographical areas, improving control and optimization techniques have become indispensable. In this paper a review of the authors? previous work in terms of improving control and optimization of converter operational practices related to magnetite content and precipitation, slag and metal blows, problematic and dangerous elements such as As, Sb etc. has been described by highlighting the advantages that the new control and optimization methods and tools bring to everyday converter practices. Several examples are given and future work is underlined

Jan 1, 2005

By Varadarajan Seshadri

A physical model based on similarity principles was constructed for simulating the RH degasser of CST (Companhia Siderurgica Tubarao, Vitoria, ES, Brazil) to evaluate the circulation rate of the metal which essentially defines the degree of exposure of the metal to vacuum in the chamber and thus of the refining rate, The circulation rate on the other hand will influence the decarburization rate and removal of dissolved gases like nitrogen and hence it is essential to optimise this parameter to get maximum refining efficiency with minimum refining times, thus improving the productivity of the secondary refining process. Mixing characteristics in the ladle is evaluated by pulse tracer addition using conductivity-meters located at the down leg as well as at several locations in the ladle. The influence of gas injection through nozzles in the upleg with simultaneous bottom injection of gas as well as nozzle blockage on the circulation rates were investigated. Also simulation experiments of kinetics of decarburization were carried out using CO2 adsorption-desorption process in sodium hydroxide solution as circulating fluid and the effect of, bottom gas flow rate in this case was also evaluated. The results were carried over to prototype and to optimize the process.

Jan 1, 2003

By Jewel A. Gomes

Keywords: Electrocoagulation, arsenic removal, fuel cell, windmill, energy simulation, combined Fe-Al electrode assembly Arsenic contamination of well-water in different countries has caused signs and symptoms of arsenic poisoning. Although several physicochemical treatments are presently used for the removal of arsenic compounds from drinking water, an electrochemical treatment, electrocoagulation, is a promising processing technology and currently is the most efficient (above 99% removal) and environmentally friendly technique, particularly if combined with alternative energy sources. Wind and fuel cell technologies can be considered the most promising developmental clean power sources. We will discuss new insights into the materials processing mechanisms and show the coupling of electrocoagulation with fuel cells and simulated wind energy sources. Different electrocoagulation plate materials were considered, along varied currents from the fuel cell to produce maximum arsenic removal. Coupling these technologies will remove carcinogenic arsenic from water sources, and will exhibit efficient usage of these energy sources by producing pure water for human and agricultural consumption.

Jan 1, 2005

By Wilhelm Wendt

About five years ago we showed that it is possible to use the spectral in- formation in the light emitted by the off-gas flame of a PS converter for on-line production control. Very recently measurements have been performed using improved optical equipment and data evaluation software, resulting in both improved accuracy and the establishment of new optical process parameters. Using the optical signals the slag heats could be stopped at a predetermined Cu content of the white metal with an accuracy of +0.2% Cu m the range 74-78% Cu. A good correlation was found between the slag composition and optical data, providing a possibility for on-line monitoring of the SiO2 content of the slag. The measurements indicate the possibility of predicting the optimum end-point of the copper-making stage and having real time information on the impurity removal. Factors influencing the optical parameters, such as blowrate, Pb content, temperature etc. will be discussed.

Jan 1, 1993

By P. Halsall

Smelters of medium or low grade tin concentrates must recover a high proportion of tin from iron-bearing slags or concentrates; the volatility of tin sulphide makes possible the production of iron-free tin fume. Laboratory work defined conditions which would promote the sulphidisation of tin slags and concentrates melted with them, to result in tin recovery as fume, and a residue of less than 0.5% Sn content, which could be controlled to vary with the value of tin. Subsequently pilot-plant work on 6-tonne and 15-tonne scale led to a commercial plant of 45 tonne. capacity (1962), for melting and fuming primary and secondary low-grade tin materials by submerged combustion. Some factors contributing to the rate of Working expressed in terms of the 'half-life and the amount of work done, the 'half-life-tonne' are studied, leading to the design and operation (1972) of the 100-tonne water-jacketed unit, presently in use, treating a wide range of slags and low tin-content ores and residues.

Jan 1, 1983

By Michael S. Moats, Scott C. Campin, J. Brent Hiskey

"Electrochemical techniques are a valuable means of analyzing the passivation of commercial copper anodes. Electrochemical impedance spectroscopy (EIS) provides information concerning transport and reaction phenomena occurring at an electrode surface. Commercial. copper anodes of varying compositions have been examined using EIS. Experiments were conducted in a flat cell with an electrolyte of 40 gil Cu2 + and 160 gil H2S04 maintained at 65 DC. Impedance spectra were obtained at the potentials characteristic of the open circuit voltage and passive region for each anode. The spectra of the passivating films exhibited a flattened resistive/capacitive loop at middle to high frequencies and an inductive loop at low frequencies. An equivalent· circuit utilizing an inductor-resistor series in parallel with the double layer capacitance and charge transfer resistance was adequate in modeling the impedance data. The influence of anodes impurities on the components of the equivalent circuit is discussed and correlated with a hi-layer passivation model.IntroductionPassivation of copper anodes during industrial electrorefining has received considerable attention in the past few decades. Great strides have been made in understanding the roles of anode impurities [1-25], electrolysis parameters [20,26], and electrolyte chemistries [20,26]. Even so, passivation still occurs even in the most modem of refineries. The exact cause of passivation is not fully understood. It is known that the anode surface becomes covered by a passivating film. This film has been proposed to be CuS04'&5H20, Cu20, or mixed oxides. The localized concentrations of Ft, Cu+, and Cu2+ ions determines which phase is more favorable. The presence of these ions is controlled by the reaction kinetics and diffusion of species through the slimes layer.Reaction kinetics between Cu, Cu +, and Cu2+ are based on the dissolution mechanism of copper. There exists four different models to describe the dissolution of pure copper. The classical model of Mattsson and Bockris [27] involves two single electron transfers with the cuprous-cupric reaction being the rate detennining step. More recently, Wong, Collier, and MacFarlane [28] used ac impedance to elucidate a more complex mechanism involving the affect of pH and anions. Their findings indicate that the formation of cuprous ions in solution, Cu(I)so~ is favored over Cu(1I) ions adsorbed to the electrode surface in the presence of sulfate and as pH increases from pH 1 to pH 5."

Jan 1, 1997

By Kymberley Worrell

The Cripple Creek and Victor Gold Mine was acquired by Newmont in August 2015. The high grade flotation mill project was commissioned in February 2014. The mill to date has been throughput limited due to mechanical and design issues. In order to create the most value from a throughput limited plant a campaign to provide timely ore characterization was undertaken. A diagnostic leach methodology was developed to determine gold associations by ore type. The resulting associations were then used to characterize feed blend; gold losses and optimize gold production. The diagnostic methodology is presented along with discussion on flotation implications.

By Jean-François Boulanger

The production of rare earth elements from ore usually consists of three steps; the separation of a concentrate of REE bearing minerals; the cracking of the REE minerals to liberate the REE into an aqueous solution and separation of REE into individual elements. This paper describes the results of laboratory tests conducted on a carbonate-rich REE ore containing bastnaesite and monazite. The tests cover the whole processing sequence of beneficiation, preparation of the REE solution using a caustic leach followed by acid leach to break monazite and bastnaesite and liberate REE into an aqueous solution and the partial separation of the REE using solvent extraction. Details on the product quality and process performances (recovery and impurities removal) are given for each studied step. The paper also discusses the economic advantage of separating the REE rather than producing a mixed REO product to be sold to a refinery for REE separation. A mini-pilot plant version of the process is currently planned.

By Dong Hoon Han

The sulfation rates of magnesium oxide and calcium oxide (molar ratio 7:3) contained in calcined CMA ( calcium magnesium acetate) by SO2 were measured. The experiments were carried out in the temperature range 700 to 1100 °C and under the SO2 concentrations of 0.3 to I mol % (5 % 02). In the low-temperature range below 830 °C the reaction produced CaSO4.3MgSO4 and unreacted MgO, but no MgSO4 phase. The formation of CaSO4.3MgSO4 phase has a significant implication in that it allows the utilization of MgO for SO2 removal whereas the sulfation of MgO from conventional sources is so slow that it is of no practical interest. Thus, the calcined CMA can remove SO2 at lower temperatures than conventional SO2 absorbents and at a greater capacity. Above 950 °C only CaO reacts with SO2, but at a much greater rate than the calcined Ca(OH)2, which is one of the most reactive SO2 absorbents.

Jan 1, 1998

By Hang Goo Kim

A computer simulation has been carried out to predict the distribution behavior of minor elements such as Pb. Zn, Bi, Sb and As in recently proposed copper smelting and converting processes with submerged oxygen injection in which tonnage oxygen is used with a shielding gas. In this study the technique of stepwise equilibrium modeling was employed and some of the thermodynamic data were updated or reassessed. The volatilization and slagging of undesirable elements were investigated in copper smelting (steady-state) system, copper matte converting (batch) system, and the combined (smelting + converting) system at extremly high oxygen-enrichment levels. The predicted minor-element behavior under high oxygen- enrichment was compared with that in the Noranda process (normally 42% oxygen-enrichment in smelting and 24% in converting) and the reverberatory process using air. The effects of various operating parameters such as temperature, the final matte grade in smelting, the initial matte grade in converting and the O/Fe ratio in slag on the behavior of minor elements are discussed.

Jan 1, 1991

By Won C. Park

Experiments showed changes in the mineral content of dolomitic oil shale at temperatures and exposure times which bracket conditions encountered during in situ retorting. Laboratory results correlate with cores from a spent in situ retort at Occidental's Logan Wash test site at Garfield County, Colorado. Dolomite, CaMg(CO3)2, decomposes rapidly to form periclase, MgO, calcite, CaCO3, and CO . Both calcite and periclase are intermediate products that can be stabilized by CO atmosphere at lower temperatures, while steam accelerates the formation 2 of silicates. The decarbonation of calcite appears to involve a direct reaction with both quartz and periclase in forming these silicates. Decarbonation preceeds the formation of akermanite, Ca2 MgSi 207, and diopside, CaMgSi 206, within several hours of heating and is followed by the nucleation of forsterite Mg2SiO4, and monticellite, CaMgSiO4. Under in situ retorting conditions, akermanite and diposide are the major minerals above 800°C. Equilibrium is not attained within 200-300 hours. In situ retorting temperatures above 800°C for extended periods of time should reduce potential ground water leaching by the formation of silicate minerals. These silicates are less soluble than free lime, magnesium or alkali oxides. There is a corresponding decrease in the natural pH of these silicates from approximately 12 down to 7.5 to 9:

Jan 1, 1981

By Lloyd Robert Nelson

The historical progression in installed electric furnace smelting capacity of some 1650 calcium, chromium, manganese, nickel and silicon ferro-alloys furnaces is reviewed. Key increases in the inherent installed electrical capacity, often achieved through uprating furnaces, are identified. Possible factors facilitating such advances are explored, including: specific process engineering and pyrometallurgical enhancements (e.g., improved control over the consistency, size and chemical form of raw materials, extents of preheating and pre-reduction delivered into the furnace; and patterns of feed distribution); furnace electrical configuration (AC or DC; immersed, submerged-, shielded- or open-arc); form of electrode (graphite, self-baking or composite); furnace configuration (circular or rectangular; closed or open and 1-, 3- or 6- electrodes); better engineering and equipment designs (e.g., high-intensity cooling) and state of furnace electrical and metallurgical control systems. A view is presented on the prevailing state of evolution of the Mega-scale in ferro-alloy smelting and opportunities for still further improvements.

Jan 1, 2014

By T. V. Swaminathan

Monazite sand is normally processed by, the caustic soda route to produce mixed rare earths chloride, thorium hydroxide and trisodium phosphate. Bulk of the mixed rare earths chloride is used for the preparation of FC catalysts. Recently some of the catalyst producers have shown preference to cerium depleted (lanthanum enriched) rare earths chloride rather than the natural rare earths chloride obtained from monazite. Therefore, a process for producing cerium depleted rare earths chloride, cerium p thorium and uranium from Rare earths + thorium hydroxide obtained by treating monazite based on stepwise hydrochloric acid extraction, was developed in our laboratory. The process involves drying of the mixed rare earths-thorium hydroxide cake obtained by monazite-caustic soda process followed by stepwise extraction of the dried cake with hydrochloric acid under specified conditions.

Jan 1, 1989

By Mingming Zhang, Marshall S. Coe, Marcelo W. Andrade

To supply iron units and flux burden in blast furnaces, sinter basicity is one of the vital parameters for sinter plants. The sinter basicity also plays an important role in sinter quality since it imparts the formation of different mineral phases in sinter. Pot-grate sintering tests were carried out with low and high basicity to investigate the effects of sinter basicity on sinter mineralogy, properties and productivity. It was found that with an increase in sinter basicity, both sinter productivity and reducibility (RI) increased. Tumbler index (TI) and low temperature degradation index (LTD) of high basicity sinter were comparable to low basicity sinter. Softening and melting tests showed that sinter with 3.5 C/S basicity had slightly higher softening temperature comparing to lower basicity sinter with C/S 2.6, acid and fluxed pellets. XRD analyses confirmed the formation of silico-ferrite of calcium and alumina (SFCA) and calcium ferrite (CF) in the tested sinter samples.

Jan 1, 2015

By R. Tunold, Y. J. Zhang

"The cathodic kinetics of aluminum deposition from aluminum chloridealkali chloride melts was studied by use of electro-cnemical transient techniques at 700 °C. Aluminum deposited as an insoluble product on a glassy carbon electrode and as a partly soluble product on a tungsten electrode. The deposition was found to be a simple diffusion controlled process involving the exchange of three electrons. The diffusion coefficient of aluminum chloride was calculated - 4.sx10-s cm2 ·S-I in AlCl3 -NaCl-LiCl melts and 2.6x10-s cm2 ·S-' in AlCl3 -NaCl-KCl melts. For AlCl3 -NaCl-CsCl system the diffusion coefficient exhibited some uncertainty due to nucleation. The determined rate constant of aluminum deposition reaction was on the order of 10-' -10-2 cm'S:' Constant potential electrolysis was carried out. TiB2 was well wetted by aluminum. The species of melts penetrated into graphite and glassy carbon but not into tungsten. The diffusion coefficient of species in glassy carbon was evaluated.IntroductionAluminum chloride electrolysis is attractive for its power saving of 30%. Different process to circumvent the conventional chlorization to obtain aluminum chloride economically, such as directly chlorizating mixture of Al~03 and C in a cell with A-shaped laminated bipolar electrodes by rising chlorine (1), or by use of a composite anode (2), will promote the electrolysis technology to be realized industrially. With the appearance of the Alcoa process periodically there are studies on the kinetics of aluminum deposition. Some discrepancies seem to exist on the mechanism of aluminum deposition. Borne studies (3,4,5) showed that the deposition of aluminum was hindered by diffusion process in the melts. M.Gabco et a1. (6) claimed a preceding dissociation of a complex being the rate controlled step. This paper presents our results on the mechanism of aluminum deposition from the study by use of transient techniques and some results from constant potential electrolysis."

Jan 1, 1988

By F. Baldini, M. S. Borges

"The proposed method emphasizes the optimization of waste management with regard to the exploitation of raw materials incorporated in the remains of industry, as well as the economics of natural resources as an environmental impact assessment. This system [tool] allows: (a) the conversion of an environmental liability into an asset by finding a line of appropriate research for each type of waste and the development of new materials applicable to other industries, (b) the performance of internal control of the waste generated (production, storage, final destination) as well as legal conformity.Objectives:1.1 General objective:To design a collaborative system for socio-environmental management of industrial waste.1.2 Specific objective:Develop evidence of concepts;Evaluate the deployment of the inventory of waste in an industry;Enable the conversion of an environmental liability into an asset by finding a line of research appropriate to the waste: a case study;Evaluate the environmental legislation in the legal mechanisms that influence company decisions.IntroductionThe global economy is undergoing major changes, among these changes; it should be highlighted those related to technological progress and environmental quality.While the industrialized countries and higher levels of economic growth dominate modem technology, developing countries are identified by a different growth pattern, using the annual growth rate of Gross Domestic Product per capita [3, 18].Growth is when the GDP grows, in percent, over the previous year. Development, on the other hand, is when the countries change their technologies and improve their internal structure. Thus, the growth considers the accumulation of wealth, while the development is concerned with the distribution of wealth, improvement of the quality oflife and environmental quality [3, 18].As the UNESCO report shows (1999), the biggest problem is between consumption and development, what is produced and the end that is given to the product. Therefore, product and by-product have equal importance in the quantity produced [29].On one hand there is a positive relationship between indicators of economic growth and technological progress, however, on the other hand, these transformations are a paradox, confirmed by the dramatic use of environmental resources and the lack of technologies for recycling of industrial scrap."

Jan 1, 2011

By D. R. Kreuzer

The sulfide smelting industry is striving for up-scaling their operations by increasing the throughput and efficiencies of the furnaces. The physical phenomena related to refractory materials prevailing in smelters and furnaces are highly complex. The refractory materials are exposed to fairly high temperatures, thermo-mechanical stresses, penetration of pores, erosion and chemical corrosion. The application of numerical simulation tools is needed for the refractory engineering task to consider those phenomena and to evaluate the impact of operational regimes on the refractory design and finally on the integrity of the furnaces. The work discusses case studies of simulations addressing problems and questions related to the refractory design process. Practical simulation approaches which employ simplified models are introduced as the engineering process demands results in a reasonable time.