Search Documents

By G. C. Xiao

A database, incorporating historical data from British mines, to study the factors affecting inflows from proximate aquifers into longwall workings, showed that a main casual factor was the immediate roof strata lithology. When this comprised principally stronger sandstone, there was a tendency for periodic inrushes associated with face weighting. This phenomenon is explained by the collection of water in bed sepa¬ration cavities, where free water connected to a high pressure head aquifer source, may be trapped.

Jan 1, 1990

By D. W. Evans

Mine subsidence problems due to coal extraction have occurred in a number of areas throughout the United States. Depending on the local geology, the depth of the mined seam, the type of mining method employed for extraction, and other related factors, subsidence can result in anywhere from slight displacements to a total loss of ground. These conditions can have serious consequences on the health and safety of the people living above the mined areas. A number of methods exist to provide support for the ground overlying mines. All of these methods employ some mechanism for providing additional support to either the roof of the mine or the sides of the pillars. Since failure usually occurs due to overburden stresses which are transmitted to the roof and pillars, these methods employ techniques to counteract stresses induced due to the coal extraction. The applicability of any particular method will depend on the availability of backfill material, the areal extent of the affected area, and of course, the cost. The primary use of coal ash for subsidence control has been as a backfill material for the stabilization of large areas. Large scale backfilling projects for subsidence control have been performed in Rock Springs, Wyoming, Wilkes-Barre and Scranton, Pennsylvania, and in Fairmont, West Virginia. Some of these projects have utilized sand, as well as, coal ash as backfill material. Much of the backfilling work performed in the United States has been done in an effort to control mine subsidence in abandoned mines. South Africa, on the other hand, has used backfilling extensively both for ash disposal and to increase extraction in active mines. The utilization of repetitive fill and mine techniques has resulted in extraction increases of as much as eight percent in shallow mines and as much as twelve percent in deep mines.(1) The coal ash injection system which can be used for backfilling depends largely upon whether the mine voids are dry or submerged. For dry mines, hydraulic or pneumatic conveyance systems can be used, while submerged mines are limited to backfilling by hydraulic methods. The use of coal ash as a backfill material has a number of advantages, such as: 1. Coal ash is available in areas throughout the United States and in many instances is conveniently located near areas requiring backfilling. 2. Coal ash is available in significant quantities since many coals when burned will result in about 15 to 30 percent ash by weight. 3. Coal ash as backfill is, in many instances, the most economical alternative fill material. Due to the costs associated with above ground disposal, power companies will often times give the material away to lower their overall operating expenses. 4. Coal ash is usually pozzolanic in nature, that is, this material results in cementitious bonding within the backfilled matrix of material.

Jan 1, 1982

By Yunqing Zhang

Weak shales refer to those with lower strength, thinly- laminated structure, sensitivity to moisture and weathering as well as significant time dependent behavior. It has been said that many future coal reserves with good quality have weak immediate roofs. Therefore their geo-mechanical properties and behavior must be known before an appropriate support plan can be designed. In this study, four types of shales collected from underground coal mines were tested in the laboratory. Their modes of failures in underground were observed and correlated with their lab behavior. The failure mechanisms of thinly-laminated weak shales were analyzed by the means of numerical modeling.

Jan 1, 2004

By S. MacGregor

The role of horizontal stress, its orientation and magnitude, in defining the behaviour of strata in underground coal mines has been well established. Poor panel layouts have led to gate end stress concentrations, roof falls and lost production. The ability to define the horizontal stress regime over a mine site has historically been limited to point measurements, in part due to technology and cost. Recent advances in the application of geophysical tools, notably the acoustic scanner (borehole televiewer) have resulted in a new technique to conduct stress measurements. By quantifying the nature of borehole breakout and the mechanical properties of rocks in which they occur, this technique provides the ability to: obtain a vastly greater number of measurements, both at different depths and spatial distribution, than other techniques such as overcoring or hydraulic fracturing readily obtain depth versus stress relationships define geotechnical domains on the basis of stress direction and in-situ stress magnitude for mine planning purposes This paper presents an overview of the technique and presents case histories in its application at a mine site in the Sydney Basin, Australia.

Jan 1, 2002

By John Shepherd

Pillar extraction carried out using various methods (split and lift, Wongawilli and old Ben) involves the formation of narrow fenders (commonly 7 m of coal) formed by driving "splits" for lifting off with a continuous miner. The strata above a split and fender adjacent to the goaf consists of a cantilever beam (usually >3 m thick) that extends from the solid coal and bridges across the fender. Lifting off the fender from the split in safe conditions depends upon the bridging capability of the cantilever and the fender strength. The nature and competence of the immediate and near roof, the support capability of the coal fender and the presence of faults and or joints can adversely affect the bridging behaviour of the cantilever. Insufficient knowledge of these parameters can lead to extraction under dangerous conditions. Remnants of fenders ("stooks") also support the cantilever and their dimensions are critical to obtain regular caving and goaf falls. Stook area, goaf roof span and roof stand-up time after lifting can be related and only a relatively small increase in Btook area of 10-15 m2 can lead to a significantly increased stand-up time, especially under a massive roof. Such conditions strongly influence the redistribution of abutment stresses and can create increased outbye pillar loading. Based on detailed underground geotechnical investigations, it is concluded that strata caveability, roof cantilever behaviour, fender H:W ratio and remnant stook size are all critical parameters for successful and safe pillar extraction.

Jan 1, 1992

By Hamid Maleki

The U.S. Bureau of Mines implemented a monitoring program in a western U.S. coal mine for the evaluation of both conventional and alternative support systems. The conventional support consisted of 2.5-m-long vertical bolts installed in an 5.5-m-wide entry. The alternative system consisted of 2.5- and 3-m vertical and inclined bolts installed at a higher density during widening of a cut from 3.6 to 5.5 m. Roof deformation, roof stress, rib deformation, and bolt loads were monitored during the 2-month test period. In addition, roof failure patterns and lithology were characterized within the six-entry main test section. Results were analyzed using roof deformation and failure profiles, roof stress profiles. bolt loading and bending moment diagrams, and numerical models. The mechanics of roof deformation, failure, and support reaction in three zones in the mine roof were characterized. Significant improvements were shown in roof stability in the section using the alternative system. Results are encouraging and indicate the effectiveness of alternative support systems and excavation techniques for limiting inelastic deformation of roof in highly stressed underground mines.

Jan 1, 1994

By Susan Robertson

Many injuries are caused each year by rock falls in coal mines. Most of these injuries are not caused by major roof collapses, but from falls of smaller rocks from the immediate top or roof skin. Various surface controls are used in mines to control this surface rock. One that has been found to be very effective is roof screening. Depending on the size of the screen, roof coverage approaching 100% can be achieved. Many mines are reluctant to use screen for primary skin control because of additional costs of time and materials, but others are having great success at both controlling costs and surface rock. Data is presented from two mines that show a dramatic reduction in roof skin injuries when screening is used. Much of this success is due to innovations in roof bolting machines. Four case studies of roof screen experience are presented along with associated costs of materials, impact on bolting advance rates, and potential ergonomic risks. The effects of roof screening on skin control and safety are also included. Finally, this paper will provide information about features of different roof bolting machines that affect production and safety.

Jan 1, 2002

By P. A. Gray

Artificial ground support has developed into a relined science over the past 20 years. From reactive support systems such as timber props and steel supports, to active systems such as roof bolts and cable anchors, ground support technology has now developed efficient systems that work well in many instances. However this paper demonstrates that there is still a long way to go to develop optimum ground support systems. Some conventional rock bolts and cable anchors emphasise their tensile capacity only, without considering other factors such as their shear strength or shear modulus, or if the support member can transfer all of its support capacity to the surrounding rock. Examples are given of the use of ground anchors with high tensile and shear capacity in underground coal mining as well as examples of slope failures in open pits where the cable bolts have remained intact because they have been unable to transfer their full capacity to the surrounding weak rock mass. For underground coal mines, speed of installation is also of primary concern, but it must also have high tensile and shear capacity both in terms of strength and stiffness. Ground support systems of the future must therefore address these problems. An innovative new rock bait is discussed which goes some way towards solving these problems. This new rock bolt is screwed into the rock and thus has a direct mechanical interlock with the rock. Initial field results show that it has an extremely high anchor capacity and can be fully installed in approximately 30 seconds. It has considerable capacity to improve the productivity of the coal mining industry.

Jan 1, 1992

By Alan Bugden

Goedehoop colliery in South Africa has experienced a number of substantial roof falls in roadways and intersections. Many of these have been associated with geological slips and/or horizontal compressive stresses. This paper describes a numerical modelling study conducted after one such fall with the objective of clarifying the roof failure mechanism associated with these falls. The fall was located at an intersection and occurred as the last cut was being made to complete the intersection. One bounding surface of the fall was formed by the geological slip; the others were formed by fresh failure surfaces. The fall took place despite the slip being identified as a hazard and additional bolts being placed by the workforce. In conjunction with the modelling work tests were conducted on samples from the roof in which the fall occurred, these gave a U.C.S. of 80 -100MPa. Several in-situ stress tests had already been conducted at the mine; a further test was conducted close to the fall site. The tests show that the largest stresses are horizontal. However, the maximum stresses of 6-12MPa are small compared to the compressive strength of the root. Computer modelling highlighted a mechanism arising from the conjunction of a geological slip and horizontal compressive stresses that could result in tensile failure of the roof leading to the fall. Sensitivity studies were conducted to identify risk factors associated with this mechanism and the modelling results used to assist in formulating a support strategy to combat falls of this nature.

Jan 1, 2003

By John M. Karhnak

The Bureau of Mines has a long history of research in Ground Control. For many years, this work was done at Bureau facilities by Bureau researchers. As the tiles changed, however, the area of research interest broadened, and additional methods of implementation, such as con- tracts, were added. 'Ibis paper outlines the organization, goals, and methods of implementation of the Bureau Ground Control Program, along with procedures for project selection. This program organization is followed by several specific examples of Bureau research that will be soon ready for use in the mines.

Jan 1, 1981

By Christopher Mark

Current longwall pillar design methods are based on many assumptions about pillar and entry response to longwall abutment loads. Knowledge of the magnitude and time-of-arrival of abutment loads is essential for Improving design procedures. The abutment loads are in turn related to the development of yield zones and horizontal confining stresses in pillars. Entry stability, which is the goal of any longwall pillar design, is affected by in situ stresses as well as the interaction between the roof, pillars, and floor. The paper describes a study performed in a longwall panel at a West Virginia coal mine. The behavior of two headgate pillars and the adjacent entries was- monitored as the longwall face approached and moved past. The results provided a detailed picture of the response of long- wall pillars and entries to abutment loadings.

Jan 1, 1986

By Murali Gadde

Among different types of ground control problems associated with underground coal mining, those related to in situ stresses are the most common ones affecting the safety and economy of a mining operation. As a result, this has been the focus of many ground control research works done in the last three decades. This paper summarizes a recent work done on in situ stress related ground control issues of underground coal mine development workings. The approach used in this study was three¬-dimensional finite element modeling by an implicit code, ABAQUS/Standard. In the models, roof stability evaluations were made using Hoek-Brown rock mass failure criterion. Influence of the in situ maximum horizontal stress angle on the stability of both entry and intersection was examined to help determine the best development layout orientation. Also, the effect of in situ stress ratios on the stability of development openings was studied. To make the work more general, both 'low' and 'high' in situ stress fields were considered In general, the modeling results indicated that entries oriented in the direction of maximum horizontal stress were in the best condition while those oriented at 90° had the least stability. For intersections, the maximum and the minimum stability were seen at 0°/90° and 45°, respectively. However, under some combinations of input conditions, the best or the worst conditions were noticed at same other orientations as well. Based on these findings, layout design charts were prepared for both entries and intersections. It was also found that the change in ground conditions with change in layout orientation was more significant for 'low' in situ stress fields than for the higher ones. Change in the average safety factor with change in the ratio of in situ maximum horizontal to vertical stress resembled a lognormal distribution curve. However, the effect of the ratio of in situ maximum to minimum horizontal stress lacked such a clear trend for different input combinations considered.

Jan 1, 2004

By Deno Pappas

During the past few years, the Pittsburgh Research Laboratory of the National Institute for Occupational Safety and Health (NIOSH) has been evaluating developments in sealant support systems from a ground control perspective. The proper selection and use of a sealant material can significantly enhance ground control which may result in a decrease in worker related injuries due to ground falls. The purpose of this paper is threefold: to briefly review the current state¬of-the-art technology in shotcrete and membrane developments, to evaluate the preliminary findings of a long-terra underground study of various types of sealant materials, and to examine installation practices that are critical for an effective sealant material. The underground study utilizes NIOSH's Lake Lynn Laboratory Experimental Mine to evaluate the long-term performance of several types of shotcrete and membrane materials. Sealant performance to date have been evaluated on a regular basis over a two year period. Although the study is still ongoing, critical mining practices were identified that may seriously effect the bond of the sealant materials to the mine roof and rib; most notably, the importance of scaling and thorough cleaning of the rib prior to application. Also, results from an extensive series of Schmidt Hammer tests found that the shoterete increased in strength by 70% during the humid summer months.

Jan 1, 2002

By Andrzej Walentek

In polish coal mining due to specificity of seams lying the multiple extraction is used. In this kind of mining, it is essential to take into account all geological and mining conditions which have an influence on stability and functionality of workings during their using. In view of above, for one of polish coalmines, by mean of Phase2 program, the numerical calculation were made for assessment of the influence of advancing excavation front on convergence of roadway located 30 meters above longwall was analysed. In order to verify developed prognosis, in analyzed roadway the underground investigations in scope of convergence measurement and changes of load exerted on working support were carried. As a result of these investigations it was found that real convergence on certain part of roadway was significantly larger then determined in prognosis. Additional calculations and analysis showed that the main cause of differences was underestimation of influence of dynamic load, which was an effect of numerous low energetic rockmass tremors. These tremors, related to excavated longwall, were located in close proximity of roadway in its part where the biggest convergence occurred. In current practice, in this type of convergence prognosis, the maximal value of dynamic load exerted on roadway resulted from single rockmass tremor is taken into consideration. Quantitative consideration of all tremors including their location is impossible at the stage of convergence prognosis because of lack of this type of data. This paper presents results of roadway convergence prognosis compared to results of underground investigation. Conclusions formulated on that base allow in future similar designing works for obtaining more accurate results.

Jan 1, 2013

By Srisharan Shreedharan, Gang Huang, Hongqing Song, Sijing Cai, Pinnaduwa H. S. W. Kulatilake

"Subsidence prediction due to ore extraction and backfilling during open stoping operations for an underground iron mine in China is reported in this paper. Geologic complexities including faults and interfaces between different lithologies, and the stoping and backfilling sequence adopted from the mine plans are incorporated in building a 3-D discontinuum numerical model. The stoping was simulated in two vertically stacked horizontal layers (Fig. 6), with a total of 16 stopes. Large displacements of up to 50 cm were predicted by the model along the roof of the stopes, and a maximum surface subsidence of 22.5 cm was predicted by the model . Backfilling was found to control subsequent deformation and subsidence. The extraction of the upper orebody led to relatively higher deformations in extracting the lower orebody. Finally, the predicted subsidences at all locations along a subsidence profile on the surface are shown. INTRODUCTIONThe Luohe iron (pyrite) mine, located in Hefei city, Anhui, is an underground mine in China, being mined through the open stoping and backfilling method. The orebody lies at a depth of about 400 m and has an average thickness of 250 m (Magang Steel Company, 2012a). Discovered in the 1960s, the location has a reserve estimate of 300 million tonnes, which have been mined since 2007. The orebody has been divided by the mining company into an east and a west section to facilitate planning for ore extraction.Figure 1 shows the surface above the underground mine, which is seen to contain many human settlements including villages, pastures and other infrastructure. These locations are sensitive in that they need to be protected from potential adversities due to the underground mining, such as surface subsidence. While it may be near impossible to completely eliminate the subsidence due to ore extraction, operations such as backfilling have been adopted by the mine in an effort to substantially reduce it. Hence, this paper focuses on describing the stability of stopes in the mine and estimates future subsidence in a part of the mining region through numerical modeling."

Jan 1, 2016

By Essie Esterhuizen, Michael M. Murphy, Chris Mark

"The design of underground coal mines requires a clear understanding of the overburden response, the loading of pillars, the loading of the gob, the pillar failure process, and the ultimate load carried by partly or fully yielding pillars. Very few highquality stress measurements of yielding pillars and gob loading have been made in full extraction mining. Well-calibrated numerical models can assist in providing a better understanding of the load and failure processes, provided the coal, the overburden, and the gob are all modeled with sufficient realism. A program of numerical model calibration and validation was carried out using FLAC3D.1 The models were calibrated against observed and measured performance of coal pillars and the overburden in operating mines to provide a basic set of input parameters that can be used to provide a realistic first estimate of expected ground response and pillar loading. Input parameters for modeling coal pillar response were based on data from triaxial testing on coal samples, combined with both matching the depth of failure in the coal ribs to observations as well as matching the peak pillar resistance to an empirical equation. The models were calibrated against strong roof and floor case histories in which the pillar strength is governed by failure and yielding of the coal within the pillar and the surrounding strata only had a limited impact on pillar strength. Input parameters for the overburden were determined from a large database of laboratory tests and model calibration against maximum subsidence and subsidence curvature. Further overburden calibration was carried out by matching stresses in the mining horizon to field measurements. Three examples of the application of the calibrated dataset and modeling methodology to field measurements are presented. The results show that a reasopable estimate of the in-seam stress distribution and overburden response can be obtained for both strong and weak overburden scenarios at various depths of cover.INTRODUCTIONThe planning and design of coal mine excavations requires reliable estimates of the expected strength and loading of the mine structures to achieve global stability. Empirical methods are widely used to estimate the strength and loading of coal pillars and have been incorporated into pillar design procedures, such as Analysis of Longwall Pillar Stability (ALPS) (Mark, 1987) and Analysis of Retreat Mining Pillar Stability (ARMPS) (Mark and Chase, 1997), that are widely used in the United States. ~umerical models are finding increasing application as a tool for underground mine design because of their. versatility and the ever increasing computational power available to mine designers. A prerequisite for the application of numerical models is the calibration of the models against observed rock mass response (Hoek et al., 1990; Skiles and Stricklin, 2009). The calibration process may include comparison of model results to measured stress and deformation and modifying the input parameters in a systematic manner to achieve a satisfactory agreement between the model results and measurements. Once models have been calibrated, they can be applied to evaluating similar mining layouts in similar geological conditions."

Jan 1, 2010

By Rob Thomas

"In Australia, a wide roadway is commonly defined as any roadway that is driven to a width greater than 5.5 m (18 ft). These roadways are typically required to enable the installation of longwall equipment (termed installation roads); however, other applications include the need to house conveyor driveheads and pre-driven recovery roads.As a result of the increasing size of longwall equipment and mine infrastructure, in some mines, roadway widths of between 9 and 12 m (30 and 39 ft) and are being developed.Accepting that these almost always constitute strategically important and often long-term roadways, this paper considers the use of: (i) an empirical roof support design model, which is based on over one hundred case histories, (ii) various roof support design principles, and (iii) commonly accepted strata management techniques.The paper demonstrates that wide roadways can be driven and supported to an acceptable standard providing due consideration is given to the prevailing ground conditions (including the quality of the immediate and upper roof strata, the Depth of Cover and the horizontal stressfield), the final width of the roadway and the required use of the roadway.INTRODUCTIONRoof behaviour and the associated roof support requirements in wide roadways, which are roadways typically driven to a width that is greater than 5.5 m (18 ft), are controlled by a number of key geotechnical and operational factors. The recognition of these factors is an important first step in the design process and it is imperative that each is considered in conjunction with local mine site information.The main points of note in this regard can be summarised as follows:• The greater the final width of the roadway, the greater the resulting surge in roof displacement on widening - note: a) see Figure 1 for a schematic illustration of the roof displacement trends typically measured during the development of the first pass and roadway widening, b) since displacement increases with roadway width, it is always recommended that the roadway width is kept to the minimum required and c) general buckling beam theory indicates that the capacity of any beams present in the roof will reduce in inverse proportion to any increase in roadway width squared (i.e., [final width2 -first pass width2] I final width2)."

Jan 1, 2010

By Ismet Canbulat

"In order to ensure the stability of roadways, Anglo American Metallurgical Coal (AAMC) has developed a roof support design methodology that integrates analytical, numerical and empirical modelling. This methodology currently is based on a deterministic approach (a single factor of safety against failure is calculated). However, an improved methodology, based on stochastic modelling technique, has also been developed and currently being evaluated. The main advantage of this methodology is that the design is based on the probability distributions of input parameters; thus the outcome is based on a distribution of factors of safety rather than a single factor of safety. An evaluation of factors of safety may also be used to determine the likelihood of failure, which in turn may be utilized to quantitatively determine and evaluate the associated risks in decision making process. This methodology has been evaluated at Grasstree and Moranbah North Coal Mines in the designs of roof support in various critical areas and has been proven to be successful and a better way of determining the roof support requirements.This paper demonstrates the application of this methodology in a design of an install road roof support at Moranbah North Mine, where the 1,750 tonne capacity ''world's highest rated longwall"" has recently been installed.INTRODUCTIONAnglo American Metallurgical Coal Australia (AAMC) operates three longwall (LW) mines located in Central Queensland. There is an increasing emphasis on the reliability at these operations, as the longwalls are getting deeper and facing more geologically challenging conditions. In addition, the Anglo American Vision is to achieve ""Zero Harm"" through the effective management of safety at all businesses and operations. In order to accomplish this vision, AAMC has developed a proactive ground control management system for a safe and efficient production of underground reserves.Proactive ground control management involves understanding the impacts of the geotechnical environment on likely ground behavior, and it consists of approximately 15 major elements. One of the most essential fundamentals of proactive ground control management is to utilize a roof support design methodology that considers different failure mechanisms and also takes into account all important elements. The design methodology becomes even more important when the area in question is a critical area, which is defined as a high risk roadway where any failure may cause increased levels of safety and financial risks to underground workforce and operations."

Jan 1, 2010

By Anand Bhagwat

Surface control can prevent the falls of ground between primary roof support systems and rib support. Using existing industrial products, and adopting them for mining applications, has historically attained surface control in underground mining. However, the latest innovative solution, a revolutionary wire mesh product, is designed specifically for underground mining applications jointly by Bekaert and Orica. This knotted wire mesh, FlexKnot? 2500 and FlexKnot? 3500, uses smaller gauge, higher tensile strength wires, than a chain link fence or welded wire mesh. The higher tensile wire enables the mesh to achieve greater ultimate load-bearing capacity, with significantly lower overall weight. Test results, obtained at the National Institute for Occupational Safety & Health (NIOSH) Mine Roof Simulator facility, illustrate the comparisons of the new FlexKnot with traditional 8- and 10-gauge welded steel mesh. The FlexKnot is superior in deflection, load-bearing capacity, and stiffness?categories that are critical in achieving safer surface control. It also offers enhanced corrosion resistance because of the galvanized coating applied on the individual wires prior to the knotting process. Case studies from underground coal mine installations confirm that FlexKnot has the ability to significantly reduce installation cycle time and to minimize use and repetitive manual handling of individual mesh panels. An added advantage is the ability to supply FlexKnot in rolls for quick and easy handling for either rib or roof support application. When using rolls, the bolter can install the entire roll with one continuous forward motion, unlike the wasteful back and forth travel for mesh panel.

Jan 1, 2014

By Yuanping Cheng, Jingyu Jiang, Qiang Zhang

"With the increase of mining depths, deep-seated coal seams face threats from high ground stresses, high gas pressures, high gas content, and low seam permeability, which significantly increase the likelihood of coal and gas outbursts. Challenges continue to grow in coalbed methane (CBM) extraction fields, especially for short-distance gassy multiple-seams. Research has proved that the most effective way to increase coal seam permeability is to decrease the ground stress. Protective seam mining technology is a surrounding rock control technology, which can effectively reduce the ground stress and increase the permeability of the protected coal seam. In this paper, we try to use upper protective seam mining technology to simultaneously extract coal and gas. Findings are based on a FLAC3D simulation of stress variation during the mining of the No. 12 coal seam in the Daxing coal mine, Tiefa Coalfield, China. Results indicate that, after mining the upper protective seam, the pressure-relief effects of the rock mass generated three belts and five zones below the protective seam, providing the space and time for gas pre-extraction engineering. Within the protected area, the numerical simulation indicates that the stress of the No. 13/14 coal seam reduces 95.84% and 88.25% respectively, while the expansion deformation of the protective seams reach 6.87 ‰ and 6.70 ‰ respectively, which demonstrate that the protective mining technology can provide a significant pressure-relief effect to the outburst-prone coal seam. Combining stress relief in this manner with pressure-relief from engineered gas drainage (performed by crossing boreholes from the floor rock roadway) applied before the mining of the protective seam, it would not only be beneficial to CBM drainage but also can reduce the gas outburst risk of the protected seams.INTRODUCTION Internationally, since France used protective seam mining technology to control coal and gas outburst in 1939, it has been promoted and applied in many countries (?????, 1966). Since 1958, China has taken the mining test and engineering practice of protective seam mining technology in the Beipiao, Tianfu, Nantong, Zhongliangshan, Songzao, Huainan, Huaibei, and other coalfields (Yu, 1992). Long-term theoretical research and mining practice of outbursts and dangerous coal seams show that protective seam mining technology is the most effective, safest, and most economical outburst prevention measure (Cheng, Fu, and Yu, 2009; Hu et al., 2008; Cheng and Yu, 2007). Under the condition of high gas content coal seams, the safety and efficiency of simultaneous extraction of coal and gas can be realized through a reasonable mining sequence and an effective gas extraction method (Cheng and Yu, 2003). The in situ stress distribution of the protective seam (No. 1 coal seam) and protected seam (No. 2 coal seam) during protective seam mining in the Haishiwan coalfield formation (Figure 1) (Li et al., 2014). A comparison of the stress and displacement (five zones and three belts) of the rock mass below the protective seam, and in a multiple-seam context in the Dalong Mine, is shown in Figure 2 (Jiang et al., 2015). After mining protection coal in a close-distance seam group, the small spacing between the coal seams causes the protective coal and the protected coal between part of the rock to crack through each other until the protective layer of gob is through the area. This provides a desorption of gas to the protective layer of the mining space channel, making the coal seam permeability increase to several hundred times and improving the gas discharge capacity (Zhai, 2008)."

Jan 1, 2017