Search Documents

By O. Naiker

Xstrata has modified and improved on the solid state reduction of chromite (SRC) process that was pioneered by Showa Denko in Japan and previously used at Xstrata?s Lydenburg plant. The history of pre-reduction is a long one, with the SRC process being the first and only commercially successful one prior to Premus. Krupp developed the chromite direct reduction and the rotary hearth for the pre-reduction of chromite. However, these processes have not been successfully commercialised. The are a number of significant differences between Xstrata?s patented Premus and the original Consolidated Metallurgical Industries (CMI) process. These include, the use of lower cost anthracite fines as the reductant source together with the use of unactivated bentonite as the binding agent. In addition the use of oxygen as an energy source is used in Premus but not in the original CMI process. There was a fundamental change in the operational philosophy of the process in that while the original CMI process aimed to maximize metallization of the pellets, the Premus process seeks to maximize the energy output from the kiln while still achieving the required efficiencies and hence increasing furnace output. Premus is designed to reduce electrical energy consumption, provide high recoveries of metallic oxides, and utilizes low cost reductant and energy sources such as anthracite and oxygen respectively. Due to the fact that Premus is one of the most technologically advanced and competitive processes used today in the production of ferrochrome it was the process selected for Xstrata?s new ferrochrome facility, Project Lion, that is due to be commissioned in the third quarter of 2006 in the Steelpoort Valley in Mpumulanga, South Africa.

Jan 1, 2007

By S. S. Makgato

In this study, coke oven tar additions over a range of 0?8 wt.% were evaluated as a possible substitute for imported coal fractions. The coke oven tar used was collected from tar decanters in the byproducts section of the coking plant. The moisture content in the tar varied depending on the residence time and water carryover from the coke oven tar separators to the storage tanks. Moisture contents of 1 wt.%, 3 wt.%, and 6 wt.% were investigated in order to evaluate the effect on coal blend, carbonization, and coke properties. At 6 wt.% moisture content with 6 wt.% coke oven tar, although the coke quality improved the yield showed a 4% decrease. On the other hand, 1 wt.% moisture content with coke oven tar of 6 wt.%, increased the yield by 1% and the coke quality improved. However, the latter process was characterized by an excessive increase in wall pressure and pushing energy, both of which are detrimental to the oven walls. The optimum moisture content in coke oven tar was found to be 3 wt.% with a coke oven tar addition of 6 wt.% in the coal blend. With these conditions, the coke properties improved and wall pressure and pushing energy were acceptable. However, a decrease in coke yield of up to 2% was observed. Despite this, coke oven tar addition is considered to be a viable option based upon economic factors of a reduction in the quantity and cost of imported coking coals that is required to achieve the same optimum final coke product. Keywords coal substitution, coke oven tar, tar moisture, coal blend, coke, coke quality.

Nov 1, 2013

By P J. Grobler

The current commodity boom is depleting the ore bodies at a rate not seen in the past. As the existing ore bodies get depleted, only the more inferior bodies are left for exploitation. This places an emphasis on beneficiation to upgrade the lower grade ore to high-grade feedstock for downstream processes. This paper discusses the role of dense medium separation in this quest for high-grade feedstock for the future. It covers the production and utilization of ferrosilicon and gives a future perspective of the technology. It concludes about the way ahead and the challenges facing the processing fraternity and mining industry.

Jan 1, 2006

By Pekka Taskinen

Advanced optimizing control of the fluidised bed zinc roaster has been in use for an extended period at Boliden Kokkola and the implications are seen as extended bed stability, increased throughput and far better on-line availability. The roaster furnace control system developed is based on a dynamic and predictive furnace model, with parameters determined experimentally at the site. The controller maximises the concentrate feed and keeps the furnace operational parameters inside limits given by raw material mix and equipment constraints. The products of a zinc roaster, calcine, sulphur dioxide and the side products, such as mercury, meet gradually more stringent requirements, in particular as to their assays and total recoveries in the process chain. The end users of sulphuric acid in northern Europe, among others in the pulp and paper industry, require mercury levels much less than the conventional 0.2-0.4 ppm Hg. Therefore, secondary de-mercurising circuits have been used over the last five years for further cleaning the SO2 stream allowing production acid grades with less than 0.08 ppm Hg.

Jan 1, 2008

By C. Marais

The use of machine vision in the monitoring and control of metallurgical plants has become a very attractive option in the last decade, especially since computing power has increased drastically in the last few years. The use of cameras as a non-intrusive measurement mechanism not only holds the promise of uncomplicated sampling but could provide more consistent monitoring, as well as assistance in decision making and operator and metallurgist training. Although the very first applications of machine vision were in the platinum industry, no automated process control has been developed for platinum group metals (PGMs) as yet. One of the reasons is that to date froth features could not be related to key performance indicators, such as froth grade and recovery. A series of laboratory experiments was conducted on a laboratory-scale platinum froth flotation cell in an effort to determine the relationship between the platinum grade and a combined set of image features and process conditions. A fractional factorial design of experiments was conducted, investigating 6 process conditions, namely air flow rate (x1), pulp level (x2), collector dosage (x3), activator dosage (x4), frother dosage (x5) and depressant dosage(x6), each at levels. Videos were recorded and analysed to extract 20 texture features from each image. By using artificial neural networks (ANN), the nonlinear relationship between the image variables and process conditions and the froth flotation grades could be established. Positive results indicate that the addition of image features to process conditions could be used as sufficient input into advanced model based control systems for flotation plants. Keywords Flotation, machine vision, image analysis, neural networks.

Jan 1, 2011

Phase equilibria have been determined experimentally for pseudo-ternary sections of the form ?MnO?-(CaO+MgO)-(SiO2+Al2O3) with a fixed Al2O3/SiO2 weight ratio of 0.17 and MgO/CaO weight ratios of 0.25 and 0.17 respectively for temperatures in the range 1473-1673 K. The primary phase fields present for the MgO/CaO weight ratio of 0.17 include manganosite (Mn,Mg,Ca)O; dicalcium silicate a-2(Ca,Mg,Mn)O?SiO2; merwinite 3CaO·(Mg,Mn)O·2SiO2; wollastonite [(Ca,Mg,Mn)O?SiO2]; diopside [(CaO,MgO,MnO,Al2O3)?SiO2]; tridymite (SiO2); tephroite [2(Mn,Mg)O?SiO2]; rhodonite [(Mn,Mg)O?SiO2] and melilite [2CaO?(MgO,MnO,Al2O3)?2(SiO2,Al2O3)]. For the section with MgO/CaO weight ratio of 0.25 the anorthite phase (CaO·Al2O3·2SiO2) is also present. The liquidus temperatures of ferro- and silico-manganese smelting slags have been determined. The liquidus temperatures at low MnO concentrations are shown to be principally dependent on the modified basicity weight ratio (CaO+MgO)/(SiO2+Al2O3).

Jan 1, 2004

By K. Y. Lee, J. M. Park, C. W. Park

Laboratory-scale experiments were carried out to investigate the effect of ladle slag composition on the decreasing behaviour of aluminum content in steel, i.e., reoxidation of molten steel in contact with slag, using a vertical tube furnace. The steel composition and the slag system chosen were for ultra low carbon and CaO-Al2O3-FeO-MnO-MgO based to simulate ULC steel grades. It has been observed that the reoxidation rate shows a good relationship with (T. Fe) content in slag. In case of (T. Fe) content higher than 1.5 weight per cent, the reoxidation rate increases linearly with increasing (T. Fe) content. For a given (T. Fe) content, it decreases with the increasing (CaO)/(Al2O3) ratio of the slag. However, in the case of (T. Fe) content lower than 1.5 weight percent, no particular relationships are observed between the reoxidation rate and (T. Fe) content or the (CaO)/(Al2O3) ratio of the slag. These results were used to propose for an aim a slag composition for the ULC steel grades in a steelmaking plant. Keywords: slag deoxidation, slag killing, slag composition control, IF steel, ULC steel grade

Jan 1, 2004

The roasting of sulphide ores and concentrates is often the first step in the production of metals or chemicals. In many processes, the production of sulphuric acid is viewed as a by-product, while in some plants production is an important economic factor. Regardless of the purpose, a pyrite roasting plant consists of mainly three plant sections: roasting, gas cleaning and sulphuric acid. With the addition of air, the pyrite concentrates are transformed into solid oxides and gaseous sulphur dioxide at temperatures of 600 - 1000° C. After cleaning and cooling, the sulphur dioxide in the roasting gas is further processed to sulphuric acid. Two types of reactors are used depending on the application: stationary or circulating fluid bed . For over 60 years, Outotec has progressively been developing the principle of fluidised bed technology in several different reactor types for a multitude of process applications. The versatility of the fluidised bed reactor system has manifested itself in the treatment of minerals, including solid fuels, and for metallurgical processes both in the ferrous and non-ferrous fields. Process applications have included roasting, calcining, combustion and charring of coals, as well as off-gas treatment. This paper provides a summary of the pyrite roasting technology currently used along with a simple cost comparison of pyrite roasting and sulphur burning processes.

Jan 1, 2009

The roasting of sulphide ores and concentrates is often the first step in the production of metals or chemicals. In many processes, the production of sulphuric acid is viewed as a by-product, while in some plants production is an important economic factor. Regardless of the purpose, a pyrite roasting plant consists of mainly three plant sections: roasting, gas cleaning and sulphuric acid. With the addition of air, the pyrite concentrates are transformed into solid oxides and gaseous sulphur dioxide at temperatures of 600 - 1000° C. After cleaning and cooling, the sulphur dioxide in the roasting gas is further processed to sulphuric acid. Two types of reactors are used depending on the application: stationary or circulating fluid bed . For over 60 years, Outotec has progressively been developing the principle of fluidised bed technology in several different reactor types for a multitude of process applications. The versatility of the fluidised bed reactor system has manifested itself in the treatment of minerals, including solid fuels, and for metallurgical processes both in the ferrous and non-ferrous fields. Process applications have included roasting, calcining, combustion and charring of coals, as well as off-gas treatment. This paper provides a summary of the pyrite roasting technology currently used along with a simple cost comparison of pyrite roasting and sulphur burning processes.

Jan 1, 2009

By V. S. S. Yadavalli, J. Hager, R. Webber-Youngman

"This article investigates the complex problem of a budgeting process for a large mining operation. Strict adherence to budget infers that financial results align with goals. In reality, the budget is not a predetermined entity but emerges as the sum of the enterprise’s operational plans. These are highly interdependent, being influenced by unforeseeable events and operational decision-making.Limitations of stochastic simulations, normally applied in the project environment but not in budgeting, are examined and a model enabling their application is proposed. A better understanding of budget failure in large mines emerges, showing that the budget should be viewed as a probability distribution rather than a single deterministic value.The strength of the model application lies with the combining of stochastic simulation, probability theory, financial budgeting, and practical scheduling to predict budget achievement, reflected as a probability distribution. The principal finding is the interpretation of the risk associated with, and constraints pertaining to, the budget.The model utilizes a four-dimensional (space and time) schedule, linking key drivers through activity-based costing to the budget. It offers a highly expressive account of deduction regarding fund application for budget achievement, emphasizing that ’it is better to be approximately right than precisely wrong’."

Jan 1, 2015

By D. S. van Vuuren

Titanium bearing resources can selectively be chlorinated at temperatures below 200°C if the Ti02 in the feed is nitrided before chlorination. However, the nitriding reaction is highly endothermic, requires highly reducing conditions, is only thermodynamically favourable at elevated temperatures, and is affected by mass and heat transfer restrictions. At the required processing conditions, problems might also be experienced with sintering and with melting of slag forming components in the raw materials. A test programme was undertaken to study the effects of raw material type, temperature, gas composition, bed depth, carbon to raw material ratio and residence time in order to simulate conditions required for scaling up a nitriding process. In contrast to previous experience with low-grade titanium-bearing slag containing about 30% Ti02, ilmenite and chlorinateable slag do not form melting phases under the studied nitriding conditions and hardly sintered at all. Both feed materials can readily be nitrided with conversions in excess of 90% at temperatures around 1300°C and using bituminous coal as reducing agent with fixed carbon in excess of 1.1 times the stoichiometric requirement. The conversion decreases as the bed depth of the feed material increases and the N2/CO ratio in the gas decreases. Analysis of the relative rates of mass and heat transfer into the reacting beds of ilmenite and slag showed that the heat transfer rates are more limiting than the mass transfer rates. In order to increase the throughput that can be achieved in a kiln, it would be necessary to take special measures to enhance the heat transfer rates into the mass of reacting material. One such a measure is to pre-form the mass of reacting material into thin-walled, hollow brick shapes prior to introducing it into a kiln. Depending on bed depth, temperature and N2/CO ratio, required residence times in the high temperature zone of the kiln can vary between about 6 and 10 hours. Keywords Titanium dioxide, titanium nitride, carbo-thermic, reduction, ilmenite, slag, tunnel kiln, residence time.

Jan 1, 2011

By H. Moosberg-Bustnes

In cement-based products, such as concrete and mortars, a balance between the particle sizes of the components must be kept in order to obtain the required material properties, such as workability and strength. Sometimes the aggregates lack the necessary amount of fines, hence fine particles, i.e., filler materials, have to be added. Large quantities of filler material are needed in the production of modern concrete types; one principle of self-compacting concrete (SCC) is, for instance, the use of large amounts of fillers to reduce the friction between the coarser aggregates. Use of by-products such as slag, dust or sludge from the metallurgical industries as filler materials in concrete may help to conserve natural resources and at the same time be an economically positive option. However, to be able to successfully use the available materials they must be suitable for the planned purpose, i.e., they must be compatible with cement. In this paper three different experimental studies of steel-slags will be discussed. The aim of the studies has been to investigate if it is possible to improve the steel-slags properties, by selective screening, fine wet grinding or remelting, so that the steel-slags can be used as mineral-addition/filler material in concrete. Keywords: concrete, filler, steel-slag, modification

Jan 1, 2004

Mine wide, underground wireless communications are possible with the use of Ultra Low Frequency (ULF) technology. Due to the propagation through rock of ULF radio signals a relatively small antenna can provide communications coverage over a complete mining operation. Starting as a Personal Emergency Device (PED) for emergency messaging to miners under all circumstances, the ULF communications system has grown to include capabilities of remote control of underground equipment such as pumps and fans and centralised blasting initiation. This technology is now in use on 5 continents having lately made it onto the African mining scene. The paper and presentation will provide the audience with the benefit from international mining know-how in this technology as well as local African experiences. A recent commissioning exercise for example, is expected to pay for itself in electricity savings within a few months. These and other results from practical demonstrations and usage will be covered. This novel technology becomes an integral part of the daily operating infrastructure of a mine with immediate safety and business benefits. It is able to reduce capital expenditure and is designed for ease of routine operational use. The paper will conclude with insights into current R&D for further development of this technology.

Jan 1, 2007

By J. Dvorácek

Similar to the case of any other business venture, the activities of mining industries are profit-oriented. Nothing will stop successful businesses in their quest for new localities to be prospected for minerals of their choice, because the useful economic life of any mine is limited. Before starting the process of land acquisition, it is important for any mining company to be able to forecast the profitability of the venture. The focus of this paper has been on the prospects of success, concerning the case of the opencast extraction of aggregates for construction. A set of 70 successful and loss-making quarries was subjected to investigation. An international company owns the quarries, which are located in seven European countries. The method of discriminate analysis provided the criteria for assessing future economic performance. The same criteria served the purpose of classifying other quarries belonging to the company.

Jan 1, 2012

By A. Fredriksson, R. Christiansson, I. Staub

A theoretical model based on DFN models and 2D DEM numerical modelling has been developed for evaluating the rock mass mechanical properties. The description of the methodology is non-site related and can be applied in any site for this type of characterisation. The methodology was developed in the frame of the Site Investigation programmes for a Deep Repository for spent fuel in Sweden, and validated on sets of data coming from the Äspö Hard Rock Laboratory. Un modèle théorique base sur des modèles probabilistiques de réseaux de fractures et sur un modèle numérique DEM 2D a été développé dans le but de déterminer les propriétés mécaniques de la masse rocheuse. La méthodologie développée peut être appliquée à tout type de site pour ce genre de caractérisation. Le modèle a été élaboré dans le cadre des programmes de recherche d’un site d’enfouissement des déchets nucléaires en Suède, et validé par une application au laboratoire de recherche souterrain à Äspö. Ausgehend von DFN-Modellen und 2D DEM numerischen Modellierungen wurde ein theoretisches Modell für die Auswertung von mechanischen Eigenschaften von Fels entwickelt. Die Methodikbeschreibung ist nicht standortspecifisch sondern kan überall für diesen Typ von Standordkarakteriserung angewendet werden. Die Methodik wurde in Schweden im Rahmen der Standortuntersuchungsprogramme für die Endlagerung von verbrauchten Brennelementen entwickelt und ist mit Hilfe von Daten des Äspö Hard Rock Laboratory validiert worden

Jan 1, 2003

Electricity supply constraints in SA are increasingly challenging mines to operate more energy efficiently without reducing production output. Mining compressed air systems are well known to be operated inefficiently and are also a major power consumer. Two available and proven technologies can be applied on new and existing mines to replace or and optimise available compressed air facilities and achieve meaningful reductions in electrical power consumption; ? Hydro powered drilling and mining is significantly more energy efficient than compressed air and provides drilling rates that are twice as fast. ? Stope drilling systems using compressed-air or water drills allow further energy savings. The technologies are discussed and a broad strategy to selectively apply these them together is presented.

Jan 1, 2008

By J. M. Garcia

This paper highlights several management practices from the oil and gas industry to support the proposition that financial performance in the finite, non-renewable resource business relates more to upstream rather than downstream activities. Based on the analysis of nine oil and gas companies, this study supports a previous study involving fourteen mining companies that showed reserves growth is one of the main levers of value creation in mining. Interestingly, this study also finds that the oil and gas industry has been historically more profitable than mining. The reason, it is argued, is that oil and gas companies count on management practices that focus primarily on the upstream segments of the business, compared to the traditional downstream focus of mining. This paper delves into these ideas to conclude that what mining may need to improve its competitive advantage is a new organizational framework. Another conclusion is that the upstream management focus is vital not only for strategy formulation in the resource business, but also for policy formulation in economies based on the export of finite, non-renewable resources.

Jan 1, 2011

By D. J. Adams, W. K. Rymon-Lipinski

Rock engineering plays a crucial role in contributing to sustainable development in South African mining. A framework for this has been created through legislation and structures to encourage the mining industry to have a long and prosperous future. However, rock engineering input is an essential element to achieving success. The most accessible deposits have been mined in South Africa and although large reserves still remain, many of these are difficult to access and will require excellent rock engineering knowledge and skill in the future. This is borne out by the fact that more than 50 % of fatal accidents are related to rock engineering issues. Many of these may be addressed with rock engineering solutions which are not beyond current rock engineering technology. A reduction in fatalities and injuries contributes to a sustainable mining industry.

Jan 1, 2003

By Dhananjaya Senapati, E. V. S. Uma Maheswar, C. R. Ray

Carbothermic process of Ferro Silicon production is primarily a slag-less process. However, slag formation is observed in the regular operation as experienced by almost all the Ferro Silicon Producers in different pro-portions. The problem of slagging in the furnaces may be due to: a)Variation in the input burden charge material quality b)Fluctuations in the Carbon balance and/or c)Fluctuations in the Electrode penetrations The problem will be more severe in nature with the increase of the size of the furnace. The operation performance of the furnace gets badly affected if the slag formed in the furnace is not removed from the bath in time and to the maximum extent possible. It is, therefore, very essential to know the characteristics of the slag formed in the Ferro Silicon Furnaces, besides eliminating the very cause of formation itself; and to find the routes of draining of the same from the furnace bath effectively. This paper envisages the effects of using the LIME STONE in the Ferro Silicon Burden in stabilizing the 48MVA Furnace for improved performance and better consistency. Quality fluctuations in the available Raw Materials are compared with that of the requirements for the Ferro Silicon production. The furnace operational data is compared for 12 months period each for the period corresponding to the before and after usage of lime stone in the burden and found encouraging results in the performance. Implications of use of Lime Stone in the burden on the quality of the output alloy are also studied.

Jan 1, 2007

By E. Laine

Rock density determinations are necessary for ore resource evaluations from estimated block grades in g/t. Rock density depends on the mineral composition and, thus, it is specific for each rock type. The rock density distributions for different rock types are often symmetric. Hence, the arithmetic mean is a good approximation for the average density for lithological units. However, there may exist spatial variation in density values due to alteration, fracturing and original heterogeneities such as layering. This study compares the kriged density model with the one with constant density values for different lithological units in the evaluation of metal amounts in rock blocks. The case study consisted of rock densities measured from the drill cores at Ahmavaara PGE deposit in northern Finland. The used Ni contents were simulated in accordance with the spatial distribution of rock densities. The Ni amounts in 2x2x2 m3blocks are higher for the kriged densities than for the average densities. The difference is increasing with the increasing metal amounts due to the nonlinear correlation between Ni content and rock density. The final effect on the resource estimation depends on the cutt off grade and prices of the metal, for example, for a very valuable metal the small differences are significant

Jan 1, 2003