Search Documents

By S. R. Dindarloo

Although blasting is one of the most widely used methods for rock fragmentation, it has a major disadvantage in that it causes adjacent ground vibrations. Excessive ground vibrations can cause a wide range of problems, from nearby residents complaining to ecological damage. Prediction of blast-induced ground vibration is essential for evaluating and controlling the many adverse consequences of surface blasting. Since there are several effective variables with highly nonlinear interactions, no comprehensive model of blast-induced vibrations is available. In this study, the support vector machine (SMV) algorithm was employed for prediction of the peak particle velocity (PPV) induced by blasting at a surface mine. Twelve input variables in three categories of rock mass, blast pattern, and explosives were used for prediction of the PPV at different distances from the blast face. The results of 100 experiments were used for model-building, and 20 for testing. A high coefficient of determination with low mean absolute percentage error (MAPE) was achieved, which demonstrates the suitability of the algorithm in this case. The very high accuracy of prediction and fast computation are the two major advantages of the method. Although the case study was for a large surface mining operation, the methodology is applicable to all other surface blasting projects that involve a similar procedure.

Jan 1, 2015

By C. Siyasiya

One of the problems that is occasionally encountered during the continuous casting of DIN 1.4003 stainless steel (hereafter referred to as 1.4003) is the side bulging effect, a problem that is generally prevalent in ferritic stainless steels. This occurs because the unconstrained narrow sides of the solidification shell are not able to withstand the ferrostatic pressure once the strand has emerged from the mould. Coupled with side bulging, there is strand width variation at high temperatures, i.e. when the steel is in the ferrite-austenite dual phase region. Both of these dimensional changes to the slab profile create some processing problems in subsequent hot rolling operations when unacceptable width variations are encountered. The strength of the solidification shell and its ability to withstand the ferrostatic pressure during continuous casting is dependent on its thickness and phase composition when exiting from the mould up to a few metres downstream. From the study of the high temperature metallurgical behaviour of this steel, it was observed that a thicker solidification shell when exiting from the mould and a higher austenite volume fraction in the steel would be favourable for the reduction of the side bulging effect during continuous casting. It was also found that as long as the d-ferrite to austenite phase ratio keeps fluctuating due to variations in chemical composition and process control in the dual phase region from cast to cast, the strand width variation problem would probably persist. The remedy to this effect lies in more strict chemical composition and process control during continuous casting of this steel. The hot ductility experiments revealed that 1.4003 exhibits good hot ductility in the strand straightening temperature range with a minimum of 75 per cent reduction in area and this was attributed to the high volume fraction of ferrite (0.2 to 0.4) in the steel. This would provide a remedy to side bulging by increasing the secondary cooling rate of the strand in order to form a thicker solidification shell without necessarily risking transverse cracking and other surface defects during unbending. Keywords: side wall bulging, resistance bending moment, applied bending moment, ferrostatic pressure.

Jan 1, 2005

By W. Stumpf

Mean flow stress analyses from plant mill logs for the conventionally produced hot rolled low carbon steel from the Ispat Iscor Vanderbijlpark strip producing plant, indicated a higher temperature sensitivity than that found for the equivalent SAE 1006strip steel produced in the compact strip plant of Saldanha Steel. This was confirmed quantitatively through detailed hot deformation studies on an as-cast structure as well as on a finer grained condition on the same steel. In the conventionally produced steel, activation energies for hot deformation of 309 kJ.mol-1and 388kJ.mol-1for the two respective starting structures were found, both values extending over the entire normal hot deformation temperature range of 1140 to 900°C. These and other experimentally determined constitutive hot deformation constants were applied to the hot rolling austenite grain size development model used earlier. From this, it is predicted that dynamic recrystallization occurs only in the first two break-down passes at the Vanderbijlpark plant and thereafter static recrystallization occurs after exiting from all of the remaining ten or eleven roughing and finishing passes. This is significantly different from what was predicted earlier for the Saldanha Steel plant with its lesser number of passes where static recrystallization is predicted to occur only in the last three passes. The effects of this process difference and other observed product differences between the two types of product are discussed. Keywords: Low carbon steel, hot rolling of strip steel, rolling mill log analyses, austenite grain size, grain size modelling.

Jan 1, 2004

By W. Wittke, J. Gattermann

ABSTRACT: One alternative to close a radioactive waste repository in rock salt is the construction of a “Cross Section Closure (CSC)“ sealing barrier. The proposed material for the CSC is highly compacted bentonite. To investigate the swelling behaviour of a highly compacted bentonite a large number of laboratory tests were performed. In addition, large scale model test were carried out to demonstrate the development of a nearly homogeneous and isotropic swelling pressure. The results of the large scale model tests were interpreted numerically based on the models for stress-strain behaviour and water uptake which are implemented in the finite element codes FEST03 and HYDOPO. The investigations show a good agreement of the results of the model tests and the corresponding analyses and show, that the theoretical models are capable of describing the behaviour of sealing structures based on highly compacted bentonite. ZUSAMMENFASSUNG: Eine Möglichkeit für den Verschluß eines Endlagers für radioaktive Abfälle im Steinsalz ist die Konstruktion einer Querschnittsabdichtung aus hochverdichtetem Bentonit. Zur Untersuchung des Quellverhaltens von hochverdichtetem Bentonit wurden eine große Anzahl von Laborversuchen durchgeführt. Um die Entwicklung eines nahezu homogenen und isotropen Quelldrucks nachzuweisen, wurden darüber hinaus auch Modellversuche in größerem Maßstab durchgeführt. Die Ergebnisse dieser Modellversuche wurden im Hinblick auf die Wasseraufnahme und das Spannungs-Verformungsverhalten mit Hilfe numerischer Berechnungen mit den finite Element Programmen FEST 03 und HYDOPO interpretiert. Die Untersuchungen zeigen gute Übereinstimmungen zwischen Versuchs- und Berechnungsergebnissen. Die numerischen Modelle sind somit geeignet, das Verhalten von Abdichtungsbauwerken aus hochverdichtetem Bentonit zutreffend zu beschreiben. RÉSUMÉ: Une possibilité pour fermer un dépôt final de déchets radioactifs dans sel gemme est la construction d'un étanchement de coupe transversale, fabriqué de bentonite fortement compacté. Pour étudier le comportement de gonflement de bentonite fortement compacté, de nombreux essais en laboratoire ont été exécutés. En outre, des essais sur modèle sur une plus grande échelle ont aussi été exécutes afin de prouver le développement d'une pression de gonflement à peu près homogène et isotrope. Les résultats de ces essais sur modèle étaient interprétés en vue de l'absorption d'eau et du comportement contraintes-déformations par le moyen de calculs numériques avec les programmes d'éléments finis FEST03 et HYDOPO. Les études montrent de bonnes conformités entre des résultats d'essai et de calcul. Les modèles numériques sont ainsi capables de décrire justement le comportement d'ouvrages d'étanchement fabriqués de bentonite fortement compacté.

Jan 1, 2003

By T. Struminski

The paper is aimed to assess the possibilities of usage of pyrometers and thermal cameras to study ventilation and environmental conditions in underground mines. Surface and underground thermovision tests were carried out in the Rudna mine and included channels and diffusers of some selected fan stations, shaft crest closures, engines of central fans and their instrumentation. The thermovision underground tests in the Rudna mine consisted of ventilation barriers, underground fans, temperature of rocks, ventilation machines, parts of belt-conveyors and electric machinery.

Jan 1, 2003

By H. Ogasawara

To study the preparation process of an earthquake, we should get closer to the hypocentre. In co-operation with ISS International, we had an experimental field (~200 m x~200 m) without dykes and faults in a South African deep gold mine. We have monitored more than 20,000 seismic events (M<2) with borehole tri-axial accelerometers. We used a data acquisition system with 15 kHz sampling and 120-dB dynamic range. In a remnant area at a distance of 100?200 m, an earthquake sequence associated with an M~2 event occurred. Significant changes in seismic parameters such as stress drop, b-value, energy index were observed associated with the sequence. We installed Ishii?s borehole strain meters and could monitor as large a strain change as 10-4associated with mining. However, sampling was only 4 times per hour and 12 bit A/D. A distance from the M2 sequence was ~100 m, being not close enough. Therefore, we found another field with several crosscut tunnels excavated across a fault where an M=2-3 event is expected. We installed the strain meter within several metres of the fault to monitor both shear and normal strains on the fault. The strains are continuously digitized with a 24-bit 25-Hz A/D conversion. The Earth Tide (10-8)is clearly detected. Seismicity induced by longwall mining can be compared to earthquake swarm induced by fluid intrusion to vertical dykes. We also found a decrease in energy index in the source area of M>5events a few days before the major events. Keywords: seismic monitoring, strain monitoring, seismic parameters, preparation process of an earthquake, South African gold mine.

Jan 1, 2002

Lonmin, earlier than any other primary platinum producer, had to deal with the concentrating and smelting of UG2-rich ores and concentrates respectively. Smelting was performed at a fairly modest scale compared to the company&apos;s industry peers in the platinum group metals (PGMs) industry, and was focused on smelting concentrates obtained through low mass pulls while still maintaining high recoveries at its concentrators. Lonmin gradually smelted larger quantities of UG2 concentrates. Initially two 2.3 MW Infurnco furnaces were commissioned in 1982, followed by three 5 MW circular 3-electrode Pyromet furnaces in 1991. Deep electrode immersions and moderately high hearth power densities were used in all the designs. Lonmin decided to continue with circular furnace technology when it planned its new high-intensity No. 1 Furnace. Neither Lonmin nor the technology supplier and EPCM company foresaw the challenges that scale-up would bring when applied to the smelting of UG2-rich concentrate blends. Superimposed on the high chromite content, was the low base-metal loading, mineralogical difficulties, and fine particle size that resulted from milling of all concentrates (especially UG2 and recycle materials within the smelter). Through a process of fundamental diagnoses of furnace run-outs and wear patterns observed during repairs, the main challenges operating this high-intensity furnace were identified as sulphur vapour corrosion of the copper coolers, uneven and unpredicted movements of refractory bricks with associated copper cooler lift and matte tapblock movement, the formation of three-phase &apos;mushy&apos; zones, high refractory and taphole wear rates, uncertainty in matte level and associated insufficient matte buffer height, and high furnace operating temperatures. These factors seldom worked in isolation and will be explored in more detail in the paper. The variability in furnace feed characteristics led Lonmin to redesign Furnace No. 1, to invest in backup furnace capacity, and to invest in improved monitoring and control. These improvements consisted of online and high-frequency off-line monitoring of feed chemistry and mineralogy, online pressure monitoring of water-cooled circuits, an alternative matte liquid level measurement in the furnace, and electrode immersion estimation. Improvements were also made at the converters by installing and utilizing optical spectral analysis of the converter flame to characterize converter behaviour and achieve the desired iron end-point for white matte. This paper also briefly discusses the current and future expansion plans, as well as ancillary operations at the smelter such as flue-gas handling and materials handling.

Jan 1, 2011

By R. W. Ottermann, N. D. L. Burger, A. J. von Wielligh, P. R. de Wet, J. L. Steyn

A low noise blast hole drilling system was developed to limit the risk of noise induced hearing impairment in mining operations. Noise induced hearing loss has been identified as a major occupational health risk in SA mines. The noise generated by pneumatic percussion drills is a major contributor to such noise induced hearing. This motivated the South African Safety in Mines Research Advisory Committee (SIMRAC) to commission the development of a low noise rock drill system. The system had to be designed, manufactured, tested and demonstrated in a simulated underground mining environment. The specification required noise levels below 90 dBA. Other important design considerations were ease of manual transport, setting up and operation. The primary design concept was to encapsulate a standard Seco S215 pneumatic rock drill in a composite material tube. The tube is pushed onto the rock face by a pneumatic cylinder and is sealed at the rock face by an elastic seal. The drill is pulled towards the rock face by a rope and pulley mechanism fitted inside the tube. This mechanism is powered by a second pneumatic cylinder. The actions of moving and setting the drill require two persons. However, the team can carry out the drilling function itself on several drills simultaneously because of the self-thrusting design. The drill is supported by two camlocks. The exhaust (air containing dust, water, rock shavings, oil and grease) is removed from the encapsulating tubes via exhaust tube to the end of the stope. In this way exhaust noise and air pollutants are disposed of away from personnel. Tests were conducted in a test stope. Noise levels of under 90 dBA were achieved, thereby attaining the primary design specification. This was achieved without materially compromising ease of handling. Penetration rate was somewhat improved compared to that of the standard drill, so that productivity could be maintained. Keywords: Drill, rock drill, quiet, noise, mine, underground.

Jan 1, 2003

By P. Kluge

Mining engineers frequently encounter complex design problems for which the critical components of the design are difficult to quantify or compare. Teams of people typically work on these designs and human perceptions and judgments play a strong role. To assist with this process, the analytical hierarchical process (AHP) as a decisionmaking tool is described in this paper. Although the technique is used in many other disciplines, it is currently not widely used in mining engineering in South Africa. To use the AHP process, the problem should be treated as a hierarchy that defines the goal, the alternatives to reach it, and the criteria for evaluation of these alternatives. Pair wise comparisons are conducted on the criteria of the hierarchy to establish priorities. The value of the technique is that it is simple to test for consistency amongst the pair wise comparisons to ensure that the answer obtained is better than that provided by a random selection. To illustrate the technique, the use of a backfill support system in a platinum mining project was investigated. Ten design parameters, which will be impacted by the use of backfill, were identified and weighted according to their relative importance. The result of the AHP evaluation was that the use of a backfill support system should be preferred to a conventional support system at the mine.

Jan 1, 2011

By J. -C. Trickett

The high-resolution three-dimensional (3-D) seismic reflection data acquired for Impala Platinum between 1998 and 2002 in the western Bushveld Igneous Complex form an integral part of Impala?s mine planning and development programme. These data are of sufficiently high quality to provide unprecedented 3-D models of the geological structure of the Merensky Reef and UG2 Chromitite Reef, from which the mine deduces the size, geometry and distribution of mineable blocks. Conversely, the seismic data details zones of un-mineable ground caused by structural disturbances in the form of potholes, fault zones and pegmatoid intrusions. Furthermore, variations in dip and strike are well imaged, allowing the mine planners to optimize the mine design and layout. Current interpretation work is focused on enhancing the accuracy of these geological models even further through the analysis of ?seismic trace attributes.? Preliminary testing on the Impala Platinum 3-D seismic volume has shown that attribute analysis has the potential to illuminate a number of geological reef disturbances that are otherwise ?invisible? in the original seismic time volume. Potential areas of improvement include inter alia: ?Improved definition of major fault zones ?Improved definition of zones of reef depression (?slumping?) ?Identification of reef terracing and/or reverse dip. Keywords: 3-D reflection seismics; Impala Platinum Ltd; seismic attribute analysis; seismic micro technology (SMT); rock solid attributes; dip-azimuth; instantaneous phase and similarity.

Jan 1, 2005

By D. J. de Beer

South Africa had a late start with rapid prototyping (RP), with the first system being available in 1991. Up to 1994 only three systems were available in SA. Through active research participation from the CSIR and a number of universities, supported by technology transfer programmes and industry awareness workshops, adoption of RP technologies started to grow. Internationally, RP grew to the extent that several country-based member organizations were formed, and an initiation meeting of the Global Alliance of RP Associations (GARPA) took place during the SME Rapid Conference in Dearborn, USA in 1998. South Africa (SA) was invited under the auspices of the Time Compression Technologies Centre (TCTC) launched by the CSIR, and received an invitation to become a member of GARPA through the launch of a national, inclusive organization. The latter gave rise to a RAPDASA planning/launch meeting held at the University of Stellenbosch, which culminated in the first RAPDASA international conference held in November 2000 at the CSIR, and the election of a first RAPDASA management committee, also at the 1st AGM held during the conference. RAPDASA has been a pillar of strength since then, with an annual international conference being presented. As South Africa?s RP awareness grew through the RAPDASA and independent activities, so did the availability of RP platforms in SA.SA also became a benchmark for other countries/late adopters to follow, as slowly a position of following became a position of leading through innovative applications. The paper highlights SA?s development approach and history, together with the discussion of case studies in various fields. Contribution to the light metals industry will also be discussed. Keywords Rapid prototyping, additive manufacturing, product design, rapid tooling, rapid manufacturing, medical product development.

Jan 1, 2011

By D. van Rensburg

Jointed rock slopes are generally stable, as there is no freedom of movement for blocks of rock. In an open- pit mining environment, blasting opens up space into which blocks of rock can fail, resulting in the common occurrence of slope failure. Prior to the blasting of a trim pattern, the immediate highwall is scaled, where loose rock material is removed by means of a mechanical scaler. As mining of the pit progresses, the height of the scaled highwall from the pit floor progressively increases. These highwalls are never scaled again for the remainder of the pit life, and time-dependant deterioration contributes to these highwalls becoming subject to rockfall and, sometimes, slope failure. This paper documents the development of a South African innovation, a remote-controlled mechanical highwall scaler, a world first for the mining industry. The scaler will enable open-pit highwalls to be scaled from crest to toe whenever the need arises. It will reduce the risk associated with highwalls and deliver on the Anglo American promise of producing safe, profitable platinum.

Jan 1, 2012

By J. Trckova, P. Prochazka

Physical models from equivalent materials satisfying geometrical and physical similarity have been constructed. A special technology of simulating the excavation of an opening at the front part of a tunnel and of measuring the deformation at the tunnel face was applied. The results yielded by the physical models were used to formulate constitution relations in the numerical solution. This coupled modelling enables us to predict the behaviour of tunnel structures more accurately. On a construit des modèles physiques, réalisés en matériaux équivalents et répondant aux conditions de ressemblance géométrique et physique. Sur ces modèles, on a utilisé une technologie intéressante de simulation du forage du tunnel et de la mesure de déformation du front de taille pendant le forage en progression. Les résultats donnés par les modèles physiques ont été utilisés pour formuler les relations de constitution dans la solution numérique. Une telle construction de modèles combinés permet de prévoir plus précisément le comportement de la structure du tunnel. Es wurden physikalische Simulierungsmodelle aus äquivalenten Werkstoffen konstruiert, welche die Bedingungen der geometrischen und physikalischen Ähnlichkeiten erfüllen. Bei diesen Modellen hat man die interessante Simulationstechnologie des Tunnelvortriebs sowie die Verformungsmessung beim Tunnelabbaustoß während des Vortriebsvorgangs eingesetzt. Die Ergebnisse der physikalischen Simulation wurden zur Formulierung von Konstitutionsrelationen in der numerischen Lösung genützt. So eine kombinierte Simulation erlaubt eine genauere Prognose des Benehmens der Tunnelstruktur.

Jan 1, 2003

By I. Matsunaga, K. Aoki, W. -j. Jung

Blasting is widely used in mining and basic construction because of its speed and economy to destroy the rocks. Blasting has the advantages of reduced excavation costs and shorted construction time when compared to the use of heavy machinery for excavation and cutting such as that with a tunnel boring machine. There are numerous problems with blasting, including the noise, vibration and fly rock. So it is necessary to accurately evaluate fracture mechanics of rocks on the dynamic loading condition to control the fracture process of the blasting. The tests using Hopkinson&apos;s effect for the dynamic condition using the precise detonators were performed for various strain rates on three different kinds of rocks. In the tests using Hopkinson&apos;s effect for the dynamic condition, the high-speed camera was used to observe the fracture process of the test sample rocks. As the results of experiments there was an increase in the tensile strength of rock with an increase in the strain rate for three kinds of rock on the dynamic loading. The tensile strength of rocks with high porosity on the water saturation condition was decreased on the both static and dynamic condition. It is clear that the strain rate and water saturation were influenced to the tensile strength of the rocks.

Jan 1, 2003

By Mark Van Kleek

CONTENTS ?The Falcon C ?Data from a Production Trial ?Methodology ?Scale-up ?Test Results ?Circuit Configurations ?Conclusion

Jan 1, 2006

By L. A. Thompson, A. J. Linington

"Copper–cobalt extraction is a reagent-intensive process resulting in acid consumption greatly contributing towards production costs, which in the current market conditions curtail profitability. Nanofiltration (NF) membranes have become an attractive approach in the mining and minerals industry for product concentration and reagent recovery based on the ability of the membrane to separate monovalent ions from divalent ions. NF membranes can selectively separate acids from metals and salts allowing acid to be recycled as well as the concentration and purification of product streams. Membrane technology in the field of copper–cobalt processing focusses on the concentration of Cu2+ and Co2+ in the pregnant leach solution, recovery of acid from waste streams to neutralization, recovery of valuable metals from waste ponds and process water recovery. This paper aims to provide insight into the potential applications of NF membranes in copper–cobalt processing circuits as well as a brief overview of the effects of process conditions on membrane performance and process development. INTRODUCTION The copper–cobalt industry commonly uses inorganic acids, such as sulfuric acid, in large quantities for primary leaching of copper–cobalt oxide ores and releaching during product purification (Stuurman et al., 2014). This results in numerous acidic intermediate streams containing high metal concentrations and acidic waste streams with low metal concentrations. Acid consumption typically accounts for 10–15% of the operating costs of mines in the Democratic Republic of Congo (DRC) and Zambia (Acid Plant Database, 2015). Due to remote mine locations, poorly maintained roads and cross-border conflict, the cost of sulphuric acid can range between USD 300 and 400 per ton. The pivotal role of acid in the copper–cobalt extraction process has driven many mines to build sulphuric acid plants on site to ensure a reliable acid supply, however elemental sulphur still needs to be imported which faces similar logistical challenges and contributes towards operating costs."

Jan 1, 2015

The use of a time series variogram as an aid in controlling the quality of a product was pioneered by Pierre M. Gy and is described. The ability to analyse and interpret covariance relationships time series data is possible using the variogram. The concept of stream heterogeneity allows sources of variability in process streams to be identified and isolated. Principally this is distributional heterogeneity that is due to a short range effect of segregation in the process stream related to size or composition distribution of the material on a local scale and due to a long-range change in the size and grade of the material stream. The variogram is simply a tool for representing these sources of variability in a way that is explicit, allowing identification of the source and providing important insights to temporal continuity between samples. This paper describes the chronologically related large-scale variability in an iron ore process stream (%Fe), and illustrates the control and mitigation of variability at various stages within the process using a variogram. Three main sources of variability are identified including the random variability V[0], the process variability V[1], and the variability due to cyclical phenomena V[cyclic], arising from human routine or mechanical defects. These sources of variability can be represented on the control chart that provides the plant superintendent with insights as to the sampling capability of the systems in place. Maintaining levels of variability within customer specification limits requires that production systems be controlled without overcorrecting for the trends in changing quality. This can be done only by representing the limits of control relative to the limits of specification on a control chart. Where the specification limits encroach on the control limits, one or the other, or both, may need to be changed; specification limits that constrain the control limits lead to reactive decision making that is expensive and stressful for plant operators.

Jan 1, 2008

By A. Kale

A chlorination pilot plant having capacity to produce 5?10 kg/hr of titanium tetrachloride is in operation at the chlorination facility in Mintek. The bubbling fluid bed chlorination plant can be operated in batch and/or continuous process to study the chlorination kinetics of various feedstocks. The chlorination of titaniferrous ores to produce titanium tetrachloride (TiCl4) was carried out during the commissioning of the pilot plant and also as part of the titanium programme carried out at Mintek. TiCl4 is a basic raw material for producing commercial titanium dioxide pigment and titanium metal. This paper discusses the challenges faced during the commissioning and operation of the chlorination pilot plant. It also discusses the effect on the auxiliary facilities and instrumentation as a result of the harsh operating conditions of +1000°C and use of corrosive gases like chlorine and titanium tetrachloride. It discusses the effect of physico-chemical properties of the titanium tetrachloride and iron chlorides. The effect on the chlorinator refractory lining due to heating and cooling of the chlorinator is also discussed. Besides the special provisions made during the design of the chlorinator, this paper also discusses the operational experience and possible solutions to be implemented in future. Keywords Fluid bed chlorination, titanium ore chlorination, titanium tetrachloride (TiCl4) production using fluid bed technology.

Jan 1, 2011

By P. Malíková, I. Osičková, R. Sousedíková, P. Rys, J. Dvořáček, S. Heviánková

Each mining project goes through the same life-cycle, from prospecting and exploration to closure and post-closure periods. This prompts the question whether the closure of a mine constitutes the end of its life-cycle or whether the decommissioned mine can be employed for some other purpose. Best-practice references indicate that there are many viable options. In our opinion, the production of service water is one such option. Laboratory research was carried out on the water from a flooded underground coal mine in Ostrava- Karviná coal district, Czech Republic, concerning the production of service water from pumped minewater. The research proved the practical feasibility of service or process water production. Given the effect of global climate change with regard to water resources, good prospects for this additional resource can be assumed since the water has to be pumped in any case for safety reasons.

Oct 1, 2022

By J. Labuschagne

There are a number of factors that contribute to the profitability of a mine and its associated concentrator. Chief among these is the time taken from the first hoist of material from underground to the first batch of concentrate shipped. The main aim of this project was to integrate the mining model with a concentrator production schedule to minimize the time it would take to produce concentrate (without the concentrator having to stop because of a lack of feed material) in the most capital-effective manner. A secondary goal was to ensure detailed stockpiling requirements, as the concentrator is in an area where &apos;visual pollution&apos; is to be avoided. To achieve these two goals a dynamic stockpile model was created by utilizing the mine production schedule and breaking it down to a daily production figure. Four different concentrator development models were then proposed. The difference between the mine production and concentrator consumption was integrated over the life of the mine to provide the accumulated stockpile tonnages for both Merensky and UG2 ore. To prevent a situation where the concentrator was operational without any feed, the stockpile levels were never allowed to fall below zero. When a development option was selected, the standard metallurgical performance calculations were used to derive a concentrate production schedule, which was used as a basis for commercial negotiations for the sale of concentrate.

Jan 1, 2013