Search Documents

By Allan F. Smith

The influence of hydraulic fluids on spontaneous heating in bituminous coals is determined by measurement of the temperature increases produced in coal-fluid mixtures heated to a temperature sufficient for the initiation of self-heating. Similar tests on as-received coal samples and water-coal mixtures are compared with the results obtained for the various hydraulic fluids. Three of the four coals were sampled from coalbeds known to have a history of spontaneous heating. The data provide a basis for predicting the possible effects in gob or carbonaceous refuse of coal mines.

Jan 1, 1963

By T. N. Rushton

Rate minima are encountered in the reduction of magnetite with hydrogen. In a certain temperature zone, the reaction rate decreases with rise in temperature. This is inexplicable by classical kinetic theories; neither is a transition in reduction mechanism suitable for interpreting the observed behavior, This anomaly can be fully explained by hypothesizing two species of chemisorbed hydrogen with different adsorption coefficients and activation energies for adsorption. Competition between two energetic states of adsorption occurs with temperature rise, with the low energy state predominating below the anomalous temperature zone and the high energy state above it. The presence of two possible adsorption sites appears to be characteristic for oxidic adsorbents.

Jan 1, 1968

By A. C. Fieldner

All technical facilities of the Bureau of Mines have been geared for more efficient use and conservation of mining equipment, developing plans for safety, improving the quality of coal through better methods of preparation, studying the problems of coal storage and utilization, and extending the uses of coal5/ for the war and postwar economy. The Bureau is now analyzing all of the coal purchased by the Army and much of that required by the Navy. Work on boiler feed water was doubled over last year to meet the increased demand made by the War Department for protecting vital boiler plants in many new camps and defense plants. Progress has been made in safely storing coal to reduce dangers of spontaneous ignition to a minimum and to preserve coking power. Mixtures of oil and coal to be used as a substitute fuel have been investigated. Technical service on the conversion of plants to other fuels has been given to government agencies and private consumers. The possibilities of making motor fuel,

Jan 1, 1944

By Pamplinm J. W.

"INTRODUCTION For the past six years the United States Bureau of Mines in cooperation with the University of Alabama, Tuscaloosa, Ala., the Missouri School of Mines and Metallurgy, Rolla, Mo., and certain operating companies of the Florida land-pebble phosphate district have conducted an investigation to determine the amenability of phosphatic sands to concentration. 4 This paper discusses briefly an investigation of the concentration of fine phosphatic sanads of the land-pebble district of Florida. The process used - namely, the tabling of material previously given a selective oiling treatment - is new in its application to the phosphate industry, although old in principle.The feed to the standard phospidate washery is a hydraulically wined mixture of phosphate pebbles, quartz sand, and clay in which the quartz sand grains are segregated in the fine sizes. Me standard method of concentrating (washing) consists of wet-screening. at about 20 mesh to recover the plus 20-mesh material. 5 Lately some of the washeries have introduced hydraulic classifiers for sizing of the screen undersize to recover the coarser spigot products, but even this additional treatment allows much of the fine phosphate to be wasted."

Dec 1, 1932

By Terry R. Neumann

During 1984, at the request of the U. S. Bureau of Land Management, U.S. Bureau of Mines personnel conducted a mineral survey of the 28,600-acre South Pahroc Range Wilderness Study Area (NV-050-0132). The Wit derness Study Area is located in Lincoln County, NV, about 900 miles north of Las Vegas. Five mineral properties and two mineralized zones were examined during this study; of these, one mineralized zone, two small prospect pits, and part of two claims are within Wilderness Study Area boundaries. Perlite resources were identified in the study area; however, no significant metallic mineral values were noted at any of the sites. The Wilderness Study Area is dominated by a Tertiary volcanic sequence consisting of an interlayered series of tuffs containing thin beds of volcanic pebble gravel, sandstone, and perlite. At the base of the exposed volcanic section, perlite occurs along a 2.4-mile-long zone that parallel s the study area's northeastern boundary. The perlite is suitable for filtration, insulation, and soil conditioning purposes, Because of prohibitive operation and transportation costs, the estimated 6 million tons of perlite occurring inside the South Pahroc Range Wilderness Study Area are classified as an indicated subeconomic resource.

Jan 1, 1986

By T. H. Jeffers

The U.S. Bureau of Mines has developed porous beads containing immobilized biological materials for removing metal contaminants from waste waters. The beads, designated as BID-FIX beads, are prepared by blending biomass, such as sphagnum peat moss or algae, into a polymer solution and spraying the mixture into water. Laboratory studies were conducted to determine bead sorption and elution characteristics. Batch and continuous tests demonstrated that BIO-FIX beads sorbed arsenic, cadmium, lead, and other toxic metals from acid mine drainage waters collected from several sites. Selectivity for heavy and toxic metal ions over calcium and magnesium was demonstrated. The beads exhibited excellent metal sorption and handling characteristics in stirred tanks, column contactors, and a low-maintenance passive system. The sorption process was reversible, and metal ions were eluted from the beads using dilute mineral acids. Cyclic tests indicated that the beads continued to extract metal ions after repeated loading-elution cycles.

Jan 1, 1991

By Charles F. Jackson

Waste filling has been employed for many years for supporting the walls of stopes and preventing failure and subsidence of the surrounding and overlying rock formations, and its effectiveness for this purpose has long been recognized. It is used for permanent support in ground where timbering (including square-setting) is inadequate for more than temporarily supporting the walls of the excavations. It should be rioted, however, that effective as a good, solid fill may be in resisting heavy side pressure and direct weight, its usefulness for supporting large areas of back and preventing breaking and movement of the overlying rocks is limited. Even the strongest and most uniform rocks will break if the unsupported span becomes too great; and since filling cannot be packed tightly against a horizontal back there is always a possibility of the back breaking and consequent subsidence if the maximum self-supporting span is exceeded. Planes of separation, such as bedding and fault planes, slips, and joints, are common in all rock masses; these may occur above the stoping area where their presence cannot be ascertained by observation. If too much reliance is placed upon filling for the support of a large horizontal area of back (as contrasted to support of vertical or steeply inclined walls) large masses of rock may break along a. plane of weakness, compress the fill, and leave an open space into which caving of the overlying rocks may continue until the space is filled. In this paper the term "waste filling" includes any filling material other than ore - waste mine rock, rock from surface quarries or opencuts, sand and gravel, mill sands, or slags from smelting operations.

Jan 1, 1935

By Gerald T. Homce, James C. Cawley

This paper updates an earlier report by the authors that studied electrical injuries from 1992 to 1998. The previous information is expanded and supplemented with fatal and nonfatal injury rates and trends through 2002. Injury numbers and rates were used to compare and trend electrical injury experience for various groups and categories. This information allowed identification of at-risk groups that could most benefit from effective electrical safety interventions. The data presented in this paper are derived from the U.S. Labor Department’s Bureau of Labor Statistics’ Census of Fatal Occupational Injuries (CFOI), Survey of Occupational Illnesses and Injuries (SOII) and Current Population Survey (CPS). Between 1992 and 2002, 3,378 workers died from on-the-job electrical injuries. Electricity remained the sixth leading cause of injury-related occupational death. From 1999 through 2002, 4.7% of all occupational deaths were caused by electricity, down from 5.2% in the 1992 to 1998 time period. The cause of death was listed as electrocution in 99.1% of fatal cases. Contact with overhead power lines was involved in 42% of all on-the-job electrical deaths. The construction industry accounted for 47% of all electrical deaths between 1992 and 2002, but showed overall improvement from 1995 through 2002 by reducing its electrical fatality rate from 2.2 to 1.5 per 100,000 workers. An additional 46,598 workers were nonfatally injured by electricity. Contact with electric current of machine, tool, appliance, or light fixture and contact with wiring, transformers, or other electrical components accounted for 36% and 34% of nonfatal electrical injuries, respectively. Contact with underground, buried power lines was involved with 1% of fatal injuries and 2% of nonfatal injuries. NIOSH research aimed at evaluating commercially available overhead power line proximity warning alarms is described. This research is expected to be the initial step for eventual development of a performance standard for such systems.

By Sidney Katell, JOHN H. FABER, BRYCE L. MADDOX

The information abstracted from the various publications appeared in the magazines under such headings as Business and Industry , Chemical Engineering Developments , Companies in the News , Headlines of the Month , Industrial News , Industry , Refining and Gas - Processing News , Refining News , What's Happening , and others . Although most items are related to chemical and petroleum plants , a few pertain to related fields , such as markets , drilling costs for petroleum , and field prices of crude oil . Certain articles discuss various aspects of cost -estimating procedures or description of processes . Cost bibliographies prepared by other groups are discussed in items 70 and 271. The two references can be considered as supplemental to this report , since the amount of overlap in the contents is insignificant .

Jun 15, 1957

By Warren E. Morrison

Stimulated by 4 years of continuous economic growth without inflation, demand for energy in the United States reached an alltime high in 1964. Total value of production of goods and services (gross national product--GNP) for the year was $629 billion, an increase of 6.8 percent from 1963. Allowing for price changes based on 1958 dollars, the gain in real terms was 5 percent. In 1964 the Federal Reserve Board Index of Industrial Production stood at 132, a rise of 6.2 percent. With the impetus provided by personal income and corporate tax reductions during the year, aggregate wages, profits, and consumption reached record levels. Even the persistent balance of payments problem improved. Against this background the national consumption of commercial energy increased 4.2 percent. Energy needs continued to be met largely from domestic resources with imports, mainly crude petroleum and refined petroleum products, accounting for but 7 percent of the total. Mineral energy resources, namely gas, coal, and petroleum, contributed 96 percent of the input of energy into the economy during the year. The remaining 4 percent came from hydropower and nuclear power.

Jan 1, 1965

By William R. Barton

COLUMBIUM (niobium) and tantalum are similar refractory metals with closely related properties and uses and close association in ore deposits. Until recently both metals, particularly columbium, were essentially laboratory curiosities. However, since the beginning of World War II, applied technology, under the impetus of national security requirements, has realized many chemical, electronic, nucleonic, and missile and rocketry applications, where high temperature or corrosive environments require the use of columbium or tantalum. At the same time, advances in these fields have resulted in intensive research on the geological distribution, resources, metallurgy, and properties of these two metals; their alloys and compounds; and the development of a full-fledged columbium-tantalum industry. The future appears to promise continued acceleration in such studies and ever-increasing demand for these elements. The raw material supplies of columbium are abundant, and the extractive metallurgy of columbium is well enough advanced to assure adequate supplies of the element at reasonable prices to meet any projected demands. Although the extractive metallurgy of tantalum is similarly well developed, raw material supplies are so limited that, lacking new ore discoveries, an increase in demand to five times the 1959 level would severely tax ore-production facilities. Approximately 120 tons of tantalum and about one-half as much columbium was produced in 1959. Additional quantities are consumed as compounds or additive alloys such as ferrocolumbium and ferrotantalum columbium (55).3

Jan 1, 1962

By Xinquan Zhou, Rudolf E. Greuer

MFIRE, written in Fortran 77, is a computer program for ventilation state simulation in the steady state or transient state condition. It can be applied for the calculation of normal ventilation system planning or the analysis of the dynamic state variation in a ventilation system under thermal or mechanical disturbance. The state simulator MFIRE is a useful tool for mine fire fighting. In the case of a mine fire, mine ventilation engineers want to get some help to obtain more information, such as what is happening in the underground mine and how to control the mine fire, for correct decision making. By use of program MF'IRE, forecasts can be made on the variation of airflow, temperature, and contaminant distribution in a ventilation system during a mine fire. The paths which the contaminant takes at each time interval can be traced. The program MFIRE can be of assistance in the preplanning of escape routes. It can also be helpful during a mine fire emergency and mine recovery operation. Besides of offering the information of state simulation during a mine fire, MFIRE can be applied for state control by pretesting the suitability of the selected state control measures. It is to simulate the effects of the state control measures on the airflow distribution of a dynamic ventilation system. The testing result can be used for fire fighting in a similar real case of a mine fire. By employing empirical methods or a qualitative analysis like Budryk approach, ventilation engineers can choose different combinations of locations and sizes of control devices as samples of state control for an underground mine fire. Program MFIRE can simulate the different combination samples, that consist of a certain mine fue, the corresponding different control measures, and obtain the control effects. After the different control results are compared, the state control measure, which creates the best effect among the different state control measures, will be chosen for that fire case. When a mine fire, which is similar to one of the pretested cases, breaks out, the corresponding choice of the state control measure is applied to the ventilation system. It means that the simulator MFIRE has the function of indirect state control [10]. To achieve the above two functions, state simulation and state control, the mine ventilation system condition, sometimes, should be changed in a wide range to meet the requirement of the fire fighting. These wide system condition changes, such as adding operating fans, stopping or reversing fans, changing fan characteristics, adding regulators and making airflow shortcuts are represented in the time table of the input data set When the data files are changed in a wide range, however, an iteration divergence and some other computing errors in the distribution of airflow, temperature, and contaminant may occur. More serious logical programming and flexible selection on the algorithms are wanted to meet the request of the different data sets, to achieve correct state distribution simulation and improve the iteration convergence. To enhance the reliability and common suitability of program MFIRE, it is necessary to make investigation, analysis, and modification for the formal versions of MFIRE. The version 1.29, permitting dry .calculation, and versions 2.01/v2.0, permitting dry and humidity calculation, are widely applied

By J. B. Gayle

Commercial flotation plants operate on a continuous basis that is not simulated closely by the batch testing methods widely used in Bureau of Mines laboratory studies of flotation, Batch methods indicate whether a particular separation is possible but provide little or no information about the rates at which such separations can be effected in continuous operation, Therefore, laboratory equipment suitable for testing on a continuous basis was assembled for an investigation of a number of the operating variables that influence the flotation of coal. The results of these tests lead to the following conclusions: 1. Flotation recoveries were markedly influenced by variations in the percent solids in the feed, However, the relation between these variables is complex and depends on the particular coal and operating conditions used. Flotation rates generally increased with increased cell concentrations.

Jan 1, 1962

By Yael Miron

This report describes laboratory studies by the U.S. Bureau of Mines to determine the suitability of a static oxygen (OJ adsorption test for evaluating the self-heating tendencies of coals. Reliable minimum self-heating temperature (SHT) values from adiabatic oven tests were used as standards for comparison and evaluation. A suite of six coals was tested in the adiabatic oven and in sealed flasks. In the latter tests, both undried and dried samples, in a range of four particle sizes, were examined. Miniature pressure trans-ducers monitored pressures in the flasks, and gas samples taken at the end of the tests quantified all the gases present. An excellent correlation was found between the minimum SHT's and amounts of O2 adsorbed over a 7-day period for dried coals, independent of particle size. In addition, a good correlation was obtained between the minimum SHT's and pressure changes in the flasks at the end of the test for the same coals, also independent of particle size. Based on these results, the sealed flask test can be reliably used to determine the self-heating tendency of a bituminous coal sample.

Jan 1, 1990

By Russell E. Griffin

The current state-of-the-art of fire and smoke detection technology is reviewed from the standpoint of suitability for use in underground metal and nonmetal mines. Detection modes, fire signatures, and environmental considerations are included. Preliminary results of long-term in-mine tests are presented.

Jan 1, 1979

A compilation of papers presented at the Fifth WVU Conference on Coal Mine Electrotechnology in Morgantown, West Virginia, on July 30, 31, and August 1, 1980. Papers cover areas of electromagnetics/power systems, power systems, monitoring and control, and communications.

Jan 1, 1980

By Nicholas R. Dixon

This report summarizes all work performed under Phases I, II and III of U.S. Bureau of Mines Contract H0387006, "Development of a Prototype Retrofit Noise Control Treatment for Jumbo Drills." The noise and vibration levels of four jumbo drills were characterized and a survey of percussive rock drill usage is reported. A Gardner-Denver DH 123 drill was chosen as a demonstration drill, and extensive noise diagnostic studies were performed. Noise control treatments were designed, developed and evaluated in a reverberant drill test facility. The treatments consisted of an integral enclosure/muffler for the drifter, vibration isolation of the drifter from the enclosure and feed, and a drill steel sheath. A 19 dBA reduction in overall sound power level was achieved with no loss in drilling rate. The prototype retrofit treatments were field tested in an aboveground mine and in a production section of an underground zinc mine. Long-term durability and operator acceptance of the enclosure/muffler treatment were excellent. Preliminary evaluation of the drill steel sheath was encouraging, although additional testing is required.

Jan 1, 1982

By C. W. Davie

"This paper is the second of a series of progress reports4 on a study of the hydrometallurgy of manganese which is being conducted in an endeavor to make possible utilization of the large deposits of low-grade domestic manganese ores that occur in several States.There are at least four processes in which a knowledge of the action of SO2 gas on manganese oxides at elevated temperatures may prove of value.One of these involves dissolution of manganese from ores. The Bureau of Mines has investigated the hydrometallurgy of manganese by a process in which SO2 gas, a waste product at many smelters, is passed into water to form a solvent for manganese. Although several manganese minerals were readily dissolved, rhodochrosite (MnCO3) was attacked but superficially.5 Recent experiments have shown that a roast at 650 to 9000 C. converts the manganese of rhodochrosite to a form that is quickly dissolved by a weak SO2 solution.6 Introduction of smelter gases containing much as 5 per cent SO2 during such a roast would not add much to the cost of the operation, and might result in the formation of considerable water-soluble manganese sulpate.Another case involves a subsequent step in the hydrometallurgical process, namely, the formation of oxides of manganese with simultaneous evolution of SO2 by the heating of the MnSO4 produced by evaporating its solution.A third has to do with the roasting of zinc sulphide ores containing manganese as a preliminary to leaching. During purification of the solutions to be used for the electrolytic deposition of zinc the iron must be oxidized to make possible its removal. Manganese dioxide has been used for this purpose,7 and since manganese compounds are present in some zinc concentrates,8 it is of interest to learn what happens to the manganese in a zinc sulphide or on roasting, and what portion of the manganese in the roasted product might be available for oxidation."

Oct 1, 1930

By A. Livingston

This paper on mining practice at the Fresnillo silver mines is one of a series being prepared by the Bureau of Mines on mining practices, methods, and costs in the various mining districts of North America. Two classes of ore are produced at Fresnillo. A low-grade oxidized silver ore; end a complex-base sulphide are containing gold, silver, lead, zinc, and copper. This paper is confined to a discussion of operations relating to the production of oxidized silver ores. To date, more than 10 Million tons of this ore rave been mined. The present (June, 1931) daily production is 2,000 tons of ore, and approximately 600 men are employed in the mining operations.

Jan 1, 1932

By Joan T. May

Federal Bureau of Mines studies showed that some organic amine hydrochlorides can be used as dehydrating agents for producing anhydrous magnesium chloride from hydrates and brines. Laboratory-scale tests showed that double salts are formed by reacting 35 percent magnesium chloride brine or spray-dried magnesium chloride with pyridine hydrochloride. Heating decomposed these double salts to anhydrous magnesium chloride and recycle pyridine hydrochloride. Pyridine hydrochloride also chlorinated any magnesium oxide in the spray-dried magnesium chloride. The anhydrous magnesium chloride obtained by the method described contained less than 0.8 percent oxygen. More than 98 percent of the organic amine hydrochloride was recovered.

Jan 1, 1978