Search Documents

By M. Lundström, J. Aromaa, S. Seisko

"Gold dissolution was investigated in ferric chloride media, promoted as one of the most promising alternatives for cyanide-free gold leaching. The characteristics of gold open circuit potential (OCP) and its relation to gold dissolution rate was investigated. Furthermore, the reaction mechanism of gold dissolution in ferric chloride leaching was discussed. The effect of solution variables, [Fe3+] = 0.02–1.0 M, [Cl–] = 2–5 M, T = 25–95 °C and pH = 0–1.0, on OCP and dissolution rate were studied electrochemically using rotating disk electrode (RDE) and linear polarization resistance (LPR) method with ?cyc = 1000 RPM. The investigated gold OCPs in ferric chloride solutions were found to vary between 597 and 688 mV vs. saturated calomel electrode (SCE) and gold dissolution rates between 1.2·10–5–5.0·10–4 mol s–1 m–2. Increase in temperature (25–55 °C) and ferric concentration (0.02–1.0 M) changed OCP into more positive values, while increase in chloride concentration (2–5 M) decreased it. The logarithm of gold dissolution rate was shown to increase linearly with increasing OCP at the temperature range 25–95 °C, ferric concentration range 0.02–0.5 M and chloride concentration range 2–4 M. A notable increase in the gold dissolution reaction rate was evident at T > 55 °C. INTRODUCTION Currently cyanide leaching is the predominant method used in gold production from primary raw materials (Marsden and House, 2006). However, since the Baia Mare disaster in Romania in 2000, the use of cyanide has been the subject of international concern due to the toxic nature of the chemical posing a significant health threat if exposed to the ecological entities (Hilson and Monhenius, 2006; UNEP/OCHA, 2000). Therefore, several countries e.g., Costa Rica, Czech Republic, Germany, Hungary, Turkey, many states of the USA and provinces of Argentina, have started to ban or limit cyanidation via legislation (Laitos, 2012). Thus, alternative solutions, such as thiourea, thiosulphate, oil-coal agglomerates as well as halides have been investigated in order to replace cyanide as lixiviant (Adams, 2016; Aromaa et al., 2014; Aylmore, 2005; Hilson and Monhemius, 2006; Lampinen et al., 2015). Ferric and cupric chloride leaching have been reported to have advantage over cyanidation being capable to dissolve refractory gold minerals, without pre-treatment such as pressure oxidation or roasting (Angelidis et al., 1993; Lundström et al., 2014; Marsden and House, 2006; van Meersbergen et al., 1993). According to Aylmore (2005), 4% of publications for alternative lixiviants to cyanide in gold leaching were within category oxidative chloride processes including aqua regia and acid ferric chloride leaching. Further, some patents have been granted for ferric chloride leaching of gold (Abe and Hosaka, 2010; Lundström et al., 2016)"

Jan 1, 2018

By Petrus van Staden, Dragan Milanovic, Francisco Sánchez, Eero Kolehmainen, Carlos Frias

"Currently there is no economical and viable process for on-site metal extraction from Low Grade, Complex or Poly-metallic deposits, and even more, there is not any industrial process or technology able to deal with polymetallic or bulk concentrates containing Cu+Zn+Pb base metals and also precious metals. Traditionally, metals recovery from polymetallic sulfide deposits is performed by mining, selective flotation to separate Cu, Pb and Zn concentrates, and finally, smelting/refining of those concentrates to obtain the refined metals. In many cases, selective flotation of that kind of complex ores produces low metals recovery and low concentrate quality containing impurities such as Hg, As, Bi, etc., which results in high penalties in treatment and refining charges, and consequently, worsening the economy of the mining business. Recovery of the valuable metals from Polymetallic, Complex or Low Grade ores could then be maximised by producing bulk concentrates or middling flotation products to feed novel hydrometallurgical processes, like the integral metallurgical system that is currently under development within the INTMET project. For example, producing bulk concentrates would increase more than 100% Cu+ Zn+Pb cumulative recovery versus conventional selective flotation. Founded by the Horizon-2020 EU Programme, the INTMET Project was started in February 2016 and will be running over three years. The INTMET consortium is led by Cobre Las Cruces (Spain) and integrates twelve partners from seven EU countries, and including Serbia and South Africa as well. The INTMET project represents a challenging opportunity to develop suitable technological solutions to deal efficiently with difficult, polymetallic and complex sulphide ores that are abundant in Europe and worldwide. Main activities carried out during the first 18 months of the INTMET project development includes: (i) An atmospheric leaching pilot plant having a capacity of 300 kg/h bulk concentrate which has been installed and operated continuously for nine months at the Las Cruces mine; (ii) Pressure leaching test work developed by Outotec; (iii) Bioleaching test work performed by Mintek in collaboration with MMI Bor. Prior test work was applied on bulk concentrate samples supplied from Spain, Portugal and Serbia. Some of the results of these technological developments have been very positive and are presented in this paper."

Jan 1, 2018

By M. Q. Xu

During the flowsheet development for a potential commercial Cu/Ni separation plant at the In-co?s Sudbury operation, extensive laboratory and miniplant studies were carried out. There are two potential feed streams for Cu/Ni separation at the existing operation. It is shown that Cu/Ni separation from the rougher concentrate is relatively simple without need of regrind. However, Cu/Ni separation can be difficult from the bulk concentrate because of the presence of excess flotation reagents in the bulk concentrate slurry and locked particles. Excess flotation reagents created excess froth increasing entrainment. By replacing the slurry water with tap water and with addition of some hydrogen peroxide, entrainment is minimized and good Cu/Ni separation is achieved on the bulk concentrate. Fine regrind is required to increase liberation of the locked particles for ultimately high copper recovery at the minimal nickel content.

Jan 1, 2014

By Filippov. L. O.

Metallurgical results for the copper-nickel disseminated ores were improved by using ultrasonic treatment. This has been demonstrated by processing of bubble-pulp flow in the reactor zone of a reactor-separator flotation machine. It can be explained by changes in mineral and size composition of the concentrates. Thus, the selectivity of Cu/Ni flotation for different values of the hydrodynamic parameter increases considerably. Additional effect of the ultrasound treatment has been noticed under conditions when the detachment of the gangue minerals from bubbles can be controlled. Reactor-separator has advantages over other types of flotation cells for this purpose. In fact, the weak diameter of reactors make more efficient the ultrasound effect than in conventional impeller or column flotation machines. A combination of ultrasonic treatment with original organization of gas pulp flux in the reactor-separator allows to obtain significant effects in the flotation attachment/detachment subprocesses, enhancing the process selectivity and/or recovery of substances. Increase of total recovery of copper and nickel into bulk concentrate at constant grade is 8.5% for coarse disseminated ores. For copper ore, copper recovery increased by 10% at unchanged grade of 11.7% and nickel recovery gained 17% at the constant grade of 2%.

Sep 1, 2012

By Arkady Senchenko

The paper deals with the problem of refractory gold-containing material processing. It is observed that all traditional methods for liberation of fine gold from this type of products are characterized by a number of essential disadvantages, where the main ones are ? considerable expenses for ore processing and big environmental impact. As an alternative to the existing methods there is considered a gold liberation method, which is based on the combination of ultra fine grinding process with the consequent atmospheric oxidation. The theoretical justification of atmospheric oxidation was carried out, in the result of this the mechanism and the degree of sulphide minerals? oxidation was found out, the dependence of gold dissolution speed on the slurry content in liquid phase produced by grinding and oxidation was identified. The experimental data and results of pilot-plant testing are given and the most effective grinding and atmospheric oxidation mode is selected on this basis. The performed complex of research works allowed us to use the provided technology at the gold processing plant having capacity of 8 mln. tons of ore per year. The questions, problems, advantages and disadvantages of atmospheric oxidation technology for refractory gold-containing concentrates are considered in this paper. Keywords: refractory gold-containing material processing, gold liberation method, cyanidation

Sep 1, 2012

By O. N. Mohanty, S. Mohan Rao, N. D. Rao, T. Mukherjee, P. V. T. Rao

"Tata Steel has its captive chromite resources at Sukinda, Orissa. They contain two ore types, i.e. (i) Ferruginous and (ii) Siliceous. The generation of off-grade ores is an increasing trend and simultaneously customer quality requirements are becoming ever more stringent. The ferruginous type ore also contains a considerable quantity of in-situ fines (~20% particles below 0.5 mm) that compound the beneficiation problem.In this paper, new strategies are discussed for producing additional value.added products after evaluating the present beneficiation practice in terms of changing market scenario, processing capability of the plant and ore characteristic. They would entail use of MGS - an enhanced gravity separator, for recovering additional products from plant tailings; production of ferruginous coarse concentrates (-3+0.5 mm with ~46% Cr2O3) using jigs; production of marketable grade lumpy (-40+10 mm size) concentrates from low grade siliceous ore using jigs and >2.8 Cr/Fe ratio siliceous ore fines treated in the Chrome Ore Beneficiation plant gravity circuit units and low intensity magnetic separator. The studies indicate that it is possible to recover 79-80% of the chromite, against a theoretical maximum of 82% from both the ore types, in the form of several marketable grade concentrates that would also include refractory grade."

Jan 1, 2003

By Y. D. Gao

A new technique has been developed for comprehensively recovering tantalum niobium tungsten ore by adoption of stage grinding, stage separation, combination of flotation and gravity separation, gravity separation for coarse particles, flotation for fine ones, combination of ore-dressing and hydrometallurgy. The new type and high efficiency combinative collector mainly composed of benzyl hydroxamic acid is firstly used to treat tantalum niobium and tungsten slime, besides the new type equipment for gravitational separation ?YTF-C shaking table for fine particles is adopted to treat flotation rough concentrate, hence having notably enhanced both recovery and concentrate grade of fine tantalum niobium and tungsten minerals. The commercial test obtains the tantalum concentrate assaying Ta2O5 31.98% with recovery 43.44% and tungsten product assaying WO3 89.40% with recovery 76.02%. The developed technique provides a reliable approach and an effective way for comprehensive utilization of lean fine complex refractory tantalum niobium tungsten ore resource.

Jan 1, 2014

By Klaus M. Hahn, Hermann Wotruba, Bernd G. Friedrich

"Due to an increasing demand for nickel and cobalt and the depletion of nickel sulphide deposits worldwide, the production of ferronickel from lateritic nickel ores becomes more significant. About 60 percent of nickel reserves are present in laterite deposits. Common production methods like acid leaching or smelting operations implicate high material and energy consumption. Physical processing methods are also not efficient, because of the fine microstructural intergrowth of the minerals carrying valuable elements such as nickel and cobalt. Due to the high energy consumption of metallurgical treatment of lateritic nickel ore (nickel grade: 0.8 - 3.0%, Co: 0.05 - 0.15%), the separation of waste material (about 75 - 85%) before the metallurgical treatment is desirable. Therefore, an alternative process has been developed, combining a pyro-metallurgical pre-treatment with selected mechanical processing methods. The developed process consisted of a selective pre-reduction and non-selective segregation of the contained metal phases in the first stage. By this, the properties of the metal carrying minerals were changed and could become subject to concentration by means of fine beneficiation processes afterwards. The parameters of the pre-reduction and segregation were varied and the pre-treated samples were examined concerning their efficiency of metalization grade and metal grain size. This paper describes the investigation of pre-treatment methods of a lateritic nickel ore. The pre-treatment and possible subsequent separation methods were examined with regard to the recovery of the valuable elements. Metalization grade was around 80% for both Ni and Co with metal phase grain sizes below 20 µm. Scanning electron microscopy revealed distribution of new metal phases not only on the reducing agent, but also on the “slag” material.INTRODUCTION Nickel laterites are characterized as strongly weathered regoliths with several zones containing reserves of nickel (Ni) and cobalt (Co). These laterites are formed on serpentinites and ultramafic rocks under climatic and/or tectonic conditions that have changed over time (Butt & Cluzel, 2013). The formation of Ni laterites is influenced by numerous geological and environmental factors. In general, there are three ore types named according to the dominant Ni hosting minerals: oxides, hydrous magnesia (Mg) silicates and clay silicates (Butt & Cluzel, 2013). The most Ni laterite deposits contain two of these ore types, usually an oxide zone and an either clay or Mg silicate zone. Distribution of these principal deposit types, their average Ni-bearing phases and mean Ni grade are shown in Table 1. A schematic profile of the different deposits based on the development on serpentized ultramafic rocks is given in Figure 1 (Butt & Cluzel, 2013)."

Jan 1, 2018

By Steven Bradshaw, Edson Charikinya

The application of high power microwave energy to secondary crusher products has been shown to induce micro fractures and cracks in the ore. This suggests that heap leaching could benefit from microwave-induced fractures, as the extent and kinetics of heap leaching processes depend on the accessibility of grains to lixiviants, which can potentially be improved through microwave treatment. The density and pattern of microwave induced cracks and how these cracks subsequently affect heap leaching recovery has not yet been investigated. The objective of this study was to apply X-ray micro computed tomography (X-ray CT) to investigate microwave induced cracks in large cone and HPGR crushed sphalerite particles within 3D space. The ore particles were microwave treated in a single mode microwave applicator coupled to a switched mode power supply and a water cooled microwave transmission sub system operating at 2.45 GHz. The ore particles were treated at specific absorbed microwave heating energies of between 2 and 3kWh/t by treating at 6 kW of forward power for treatment times of 1 s. X-ray tomography analysis was conducted on fine (-5+4.75) mm, medium (-16+9.5) mm, and large (-25+19) mm sphalerite particles before and after microwave treatment at voxel resolutions of 5 µm, 15 µm and 25 µm respectively. Image segmentation, thresholding and spatial registration techniques were used to study crack patterns in 3D images of HPGR and cone crushed particles. Analysis of the X-ray CT images after microwave treatment shows considerable micro crack formation within the Cone and HPGR crushed particles. The cracks pattern showed interphase cracks propagating across all phases, with no evidence of preferential cracking. A greater density of microwave induced cracks was observed on fine (-5+4.75) mm particles compared to the medium (-16+9.5) mm and (-25+19) mm large particles. The results showed overall increased particle porosity following microwave treatment.

Jan 1, 2014

By P. K. Arya

Huge quantity of copper is lost in Crown, Sill, Rib Pillars, hanging wall, foot wall and unexploited ore bodies in several closed underground copper mines and old worked out stopes of Hindustan Copper Limited at Mosaboni and other places. These mines might have been uneconomical to work with conventional mining methods. However, huge quantity of mineral reserves is lost due to their closure. Chemical and in-situ bio-wash leaching, if tried can provide an answer to facilitate the recovery of metallic values economically. Encouraging results were obtained during an experiment at North Badia Mines at Mosabani in the past. Though the experiments were not completed but whatever results obtained were very encouraging and can be successfully tried to make it viable. The results of the experiments are discussed here and a plan is suggested to recover copper from such mines.

Jan 1, 2014

By W. Z. Zu

In proved reserves of vanadium-containing titanomagnetite in Panxi, China, iron grades of ores were 50% ~ 15%. China?s metallurgical industry departments defined the iron ores containing 50% ~ 20% TFe as exploitable resources and the extreme lean iron ores containing 20% ~ 15% TFe as temporary unexploitable resources, the extreme lean ores were as waste rejected into waste dump in mining process. This paper researched process mineralogy of the extreme lean ores, adopted mineral processing technology responded to the properties of the ores to treat the ores and obtained quality vanadium-iron concentrate, titanium concentrate and sulfur concentrate, therefore successfully utilized the extreme lean ores, changed the ores from waste resources to exploitable resources.

Jan 1, 2014

By Xu Wang, Bang Chen, Xiujian Luo, Wei Tang, Xiao’ou Xia, Fangming Liu

"The inertia cone crusher has lots of advantages, such as big crushing ratio, fine particle size, material layer crushing, good passing tramp iron performance and stable technical index, realized open crushing circuit and simplified crushing flowsheet. The crusher was input to China’s Beijing General Research Institute of Mining and Metallurgy (BGRIMM) from Russia’s Mekhanobr-Tekhnika Research & Engineering Corporation at the beginning of the 1990s. This paper introduces that after years of absorption and innovation how Chinese researchers optimized and creatively designed about transmission mechanism, bracing structure, kinetic parameters, lubrication system, dust sealing system, damping system and hydraulic control system etc on the basis of keeping its advanced theory and unique structure, therefore the crusher’s stability was raised and the usage cost was reduced greatly. Accordingly the inertia cone crusher in China has been widely used in many fields, such as mineral resources and the recycling of metallurgical slag. The achievement in cooperation was fully affirmed by governments of Russia and China, and cooperation of science and technology in the mining and metallurgy industry between Russia and China is promoted greatly. INTRODUCTION From the early 1950s, the former Mekhanobr Institite(now Mechanobr-Tekhnika Research & Engineering Corporation) devoted itself to the research of inertial cone crusher and put it into industrial application in the late 1980s. Inertial cone crusher is like a maverick flower in the field of crusher. With its excellent performance and excellent application effect, it shocks the world and is destined to shine with a bright future. In the early 1990s, the chief leaders of the Beijing General Research Institute of Mining and Metallurgy (BGRIMM), Academician Sun Chuan-yao and Professor Zheng Baochen, captured the extraordinary performance and strong vitality of inertial cone crusher with keen eyes. So the two big institutes started the cooperation to introduce inertial cone crusher to China. Since then, Inertia cone crusher has been able to flourish in China and have achieved impressive results with two institutes’ continuous effort."

Jan 1, 2018

By Yuhe Tang

High Gradient Magnetic Separator with Horizontal Magnetic Line is a new type High Gradient Magnetic Separator product. It has many specific advantages, such as water-air joint discharging technique, double pulses pulp dispersion technique, multi-magnetic gradient for collecting matrix with different diameter rods, better discharging rate with the especial matrix dispose, high separating accuracy and wide applicability. In this paper, the author makes a description of High Gradient Magnetic Separator with Horizontal Magnetic Line, and puts its emphasis on analyzing industrial production data using high gradient magnetic separator with Horizontal Magnetic Line to separate weakly magnetic minerals. It is found that as the rougher for weakly magnetic minerals separation, High Gradient Magnetic Separator with Horizontal Magnetic Line has more stable metallurgical performance and cheaper running costs than other types of High Gradient Magnetic Separator when the properties of the ore change greatly and there is in the case of embedded fine particle size distribution. Keywords: high gradient magnetic separator, self cleaning technology, horizontal magnetic line, water air discharging technique

Sep 1, 2012

By S. H. Shahcheraghi

The four operational parameters including collector dosage, frother dosage, conditioning time and pH, are the most important parameters effective on the flotation kinetic. The present study has been done at the Miduk Copper Complex in the province of Kerman. The effect of operational parameters on the flotation kinetic of copper minerals were studied and analyzed, so the optimum conditions for flotation kinetic of copper sulfide minerals were obtained. Under the obtained optimum operational conditions, the recovery of copper sulfide flotation at the 95% confidence level was estimated to be between 92.76% and 95.48% and the copper sulfide flotation kinetic constant was estimated to be between 1.40 and 1.45 min-1. Results showed that the consumption of the X231 collector (O-isopropyl-N-ethylthionocarbamate) and the A65 frother (Polypropylene glycol) could decrease up to 35% and 50% respectively while the copper sulfide recovery increases about 1 up to 2% at the laboratory scale. Keywords: flotation kinetics, sulfide copper, optimization, the Miduk Copper Complex, response surface method

Sep 1, 2012

By Saeed Farrokhpay

It is known that the grinding condition has a major effect on the beneficiation characteristics of the minerals in subsequent processing, in particular, flotation. In the flotation process, particles surface and their condition can significantly influence collector adsorption and flotation performance. For example, particle shape and its surface roughness occurred during grinding may influence flotation characteristics of a specific ore. In fact, adsorption of different cationic and anionic species on mineral surfaces can be varied depending on the selected comminution procedure. The flotation performance of sulphide minerals can be detrimentally affected by the surface oxidation. The amount of surface oxidation may reduce the hydrophobicity of the mineral and makes adsorption of collectors less selective. Improved liberation may generally result in improved flotation recovery. However, this may result in finer grinding and slimes, and consequently, reduce the overall flotation recovery. This paper discusses the effect of wet and dry grinding on copper flotation of a complex Cu-Pb-Zn ore. Industrially, wet grinding is preferred due to its higher energy efficiency and owing to downstream processing requirements. In this study, series of flotation tests were conducted,and surface analysis (XPS and ToFSIMS) were performed after wet or dry grinding at two different P80 values. Mineralogical study was also conducted to investigate the liberation of valuable minerals after grinding. A higher copper flotation recovery was found for wet grinding. However, the copper recovery was increased by further grinding in both conditions (wet and dry). The results showed a higher collector adsorption on copper mineral surfaces after wet grinding. The surface analysis also revealed that the ore is slightly more oxidized after dry grinding probably due to higher temperature during dry grinding.

Sep 1, 2012

By Xuliang Yang, Yuemin Zhao, Bo Zhang, Liang Dong, Cheng Sheng, Gongmin Li, Zhenfu Luo, Yaqun He, Chenlong Duan

Coal plays an important role in the primary energy consumption of all over the world. In 2012, coal reached the highest share (29.9%) of global primary energy consumption since 1970. Coal burning mainly contributes to the emission of SO2, NOX, Hg and other impurities that jeopardize the future of environment. . Beneficiation before coal utilization is the most economical and effective technology for removing the hazardous material and gangue. In this paper, a novel process of dry beneficiation based on gas-solid two-phase flow composed of the compound dry cleaning separator (FGX), the air dense medium fluidized bed separator (ADMFB) and the vibrated fluidized bed with autogenous medium (VFB) is proposed. The main equipment and the flowsheet of the united system are described in detail. Separating principle of the FGX, ADMFB and VFB devices are all based on gas-solid two-phase flow. In FGX, gassolid suspension is composed of continuous gas flow and coal powder in feed coal. Large size coal (+6- 80mm) can be pre-separated effectively, and large size gangue can be removed effectively. Moreover, - 6mm particles fed serve as autogenous medium in FGX. The probable E value is 0.13 for -80 mm raw coal. In ADMFB, magnetic powder with -0.3 + 0.045 mm size fraction and coal powder in feed coal are compound medium solids. The separation density can be adjusted and controlled according to properties of raw coal. -50 + 6 mm raw coal can be cleaned efficiently, the probable E value is 0.05. In VFB, -6 + 1 mm coal can be separated. Generally, -80 mm raw coal can be cleaned efficiently in the united system based on gas-solid two-phase flow.

Jan 1, 2014

By Vasily V. Lodeischikov, Adolf F. Panchenko, Olga D. Khmelnitskaya, Vladimir E. Dementyev

Pilot plant tests of underground gold leaching from Maminskoye deposit oxide ores at a grade of 0,7 g/t Au were carried out. The underground leaching flow sheet includes Au dissolution by chlorine-containing solutions, Au adsorption from solution on active carbon, carbon concentrate ashing and calcine melting to produce high grade gold concentrate. The underground leaching system throughput was 15 m3 of solution per hour. Gold concentration in pregnant solutions was 0.12-0.13 mg/l. Gold recovery from solutions into carbon was in the range of 63-84%. It was demonstrated that the low Au recovery in the adsorption cycle was due to the presence in pregnant solutions of "active" chlorine, which destroys active carbon and causes a sharp decrease of the carbon loading capacity for gold. To improve the adsorption indices, previously dechlorinated pregnant solutions using bituminous coal or Na2S2O3, is recommended. Ion exchange process was tested as an alternative for gold extraction from dechlorinated solutions. In the testwork period, 4.4 kg of gold were produced with a chlorine consumption of 3.5 kg per 1 g of gold. During the tests a program of environmental protection measures was completed to provide the necessary safety precautions of the underground leaching works.

Jan 1, 2003

By X. W. Lv

The intelligent recognizing and processing system for sinter ore mineragraphy make a great convenience of recognition and measurement. Specially, it?s critical important for a successful intelligent system to extract the minerals? feature accurately and sufficiently. Reflection index, as the crucial feature of mineral, is calculated by the theoretical calculating model of index based on the principle of imaging color models. In gray histogram of minerals? micrograph, the peaks? positions represent the information about mineral categories and contents. The relationships of different minerals? peak-positions in curve of gray histogram were got by using the peak-find model of gray histogram and calculating model of reflection index. These two models which can be regard as the method of feature extraction for minerals? photomicrograph also lay a good foundation for the artificial intelligent system of recognition and processing in sinter ore.

Jan 1, 2014

By Francesco Vegliò, Luigi Toro, Francesca Pagnanelli

Different hydro-metallurgical processes have been studied in order to recover manganese(II) from oxidised minerals such as MnO2. An innovative acid reductive leaching carried out in mild experimental conditions was here considered using agricultural and industrial wastes containing carbohydrates as reducing agents. The leaching process was investigated from a kinetic and equilibrium point of view in order to optimise the experimental conditions, develop a kinetic model and obtain high purity concentrated MnSO4 solutions. To study the leaching kinetic a Shrinking Core Model (SCM) was modified by a variable activation energy term to take into account both the variable reagent concentrations and the reaction rate change with respect to the manganese dioxide conversion. The influence of the particle size in the kinetic model is discussed with the support of SEM analysis before and after leaching. Manganese extraction yield was maximised (170-190 g/L) using appropriate carbohydrates and acid excesses, while impurity concentrations were kept low (Fe<10ppm and Ca<300ppm) pre-treating the ores, using hydro-alcoholic leaching medium and different combinations of down-stream processes. In particular precipitation, solvent extraction and adsorption onto active carbon were tested to eliminate Fe and Ca from MnSO4 solutions.

Jan 1, 2003

The present work aimed to verify the possibility of using froth flotation to separate the constitu-ent minerals of an alaskite rock waste having as the main minerals quartz and feldspar. Three stages of tests have been carried through. In the first stage was used an amphoteric collector for flotation, diaminedioleate, at pH 2 and, after analyzing the final products, a very poor selectivity was ob-served. During the second stage of tests, different collectors that are normally used for feldspar flo-tation as amines, sulfonates and soybean oil were employed. Once more, it was not possible to reach reasonably selective results. In the third stage, a salt of etheramine was used for collecting the feldspar and hydrofluoric acid was utilized for controlling the pH. A simulation of three flotation steps (rougher, cleaner and recleaner) permitted to attain a good selectivity in the flotation process. A concentrate with a silica content of 96.6% was obtained. The low concentrate content of alkalis totalizing 0.52% and a feldspar recovery of 96.5% to the tailings, represented by the high content of Na, K, and Al2O3 in the tailings, demonstrated that the concentrate was made up mostly of quartz.

Jan 1, 2014