Search Documents

By Leonardo Soto, Fernando Villanueva

"Antofagasta Minerals S.A. (AMSA), for its Centinela District Project, is currently developing, at a first stage, a new 90 ktpd Concentrator Plant incorporating Esperanza Sur (ESP Sur) and Encuentro (ENC) ores. In order to dimension properly main equipment, specifically for grinding circuit, a final decision has been taken using geological and metallurgical (comminution) data from both body ores. Data was analyzed internally within AMSA and its consultants to get a final proposed circuit for further engineering studies. Specific Energy Consumption (SEC) parameter is one of the main key factors for proper dimensioning. To get an accurate value different tests have been made and modelled to ESP Sur and ENC ores. Also, operational data from Esperanza operation has been taken into account due to its similar ore characteristics to ESP Sur ore and incorporated as input data for design. Depending on data, quality and amount, it is possible to estimate accuracy for project investment and risk level, hence investment decision can be taken under good and reliable information."

Jan 1, 2014

By Fedotov. K. V., A. Y. Senchenko, V. A. Chanturiya

"The paper describes an efficient process to treat the ore from the largest in Russia copper deposit – Udokan. The recommended process is universally applicable to Udokan ores different in composition and allows reaching high copper recoveries during production of high-grade cathode copper and sulphide concentrate with 45% copper content. There are several promising trends for the process optimization and in the case they are implemented, economics of the whole project could improve significantly. One of the most important optimization options implies reduction of specific energy consumption in the course of comminution operations. Another possible option to optimize the already selected process flowsheet is production of cathode copper from sulphide concentrate directly at a mining and metallurgical plant without sending the latter to other metallurgical works.INTRODUCTIONUdokan copper deposit with resources of more than 20 million tons of copper is the largest in Russia and one of the largest copper deposits in the world. The deposit is located in Kalar District of the Trans-Baikal Territory, 30 km away from Novaya Chara railway station of the Baikal-Amur Mainline.Scientists and engineers from various research institutions have studied Udokan copper ores for years. Along the way, some conceptual process flowsheets have been proposed and each of them has its own pros and cons. The key requirement to the processes being developed was their universal application for processing of all the ore types using a single flowsheet. Due to the hard mining and geological conditions and because of complex material composition of Udokan ores it is of great difficulty to design a process which would provide for maximum economic benefits. That is why the process optimization has been ongoing until now.According to the Russian standards, the main input document for design of a metallurgical plant is referred to as a Process Design Report that covers the following key data sections: analysis of metallurgical testing results, validation of the process, design criteria, process flow diagrams, the mass and metallurgical balances, process description, equipment list and other information necessary for the subsequent design."

Jan 1, 2018

"The most common agglomeration technique in iron and steelmaking is sintering, which requires the use of iron ore/concentrate mixtures, limestone and dolomite as fluxes and coke as fuel in order to produce the required melt at high temperature to cause agglomeration of the particles. Sinter feed blends containing high proportions of magnetite concentrate are difficult to granulate and to produce granules of high permeability, and sufficiently robust quasi-particles for successful sintering operations. Since the granulation of iron ore sinter feed requires no use of a binder, the added fluxes play a vital role in holding the granule particles together until they sinter. The fluxes also help to improve the granule quality and control slag composition in the blast furnace. It is well-known that the particle size distribution of the fluxes affects the granulation effectiveness and green bed permeability which determine the productivity, physical and metallurgical properties of the granules and sinter. Hence it is necessary to understand the role of flux particle size on granule properties so as to improve the granulation of iron ore sinter feed blends containing high magnetite concentrate. In this study, laboratory granulation experiments have been carried out on iron ore sinter feed blends containing high proportions of magnetite concentrate at different addition levels of limestone and dolomite mean particle sizes, to understand the influence of limestone and dolomite particle sizes on granulation rate processes and granule properties.INTRODUCTION Increases in iron ore production to meet the global demand for iron and steel products has led to the depletion of high grade iron ores and thus the current utilisation of low grade iron ore fines and concentrates. However, sinter, pellets and the lump are the required feed types used in the blast furnace. The high basicity sinter is the main iron bearing feed accounting for 70-85% in the blast furnace due to its good metallurgical and mechanical properties that allow high productivity, efficient processes and low production cost (Adam et al., 2017)."

Jan 1, 2018

By Ray Everson, Henry Kasaini

"We carried out adsorption experiments in chloride media to study the adsorption characteristics of Pd (II) anions on the surface of activated carbon. Throughout the experiments, we used commercial activated carbon pellets (0.8 Norit). The adsorption process was interpreted by using the ionisation and adsorption model. This implies that palladium anions were adsorbed physically on a protonated surface of activated carbon either as anionic complex species (PdCl4 -2) or aqua chloro-complex species [PdCl3(H2O)-] in acidic media. Furthermore, we established that adsorption of Pd (II) species was reversible at high chloride [Cl-1] concentration. The maximum adsorption capacity (Qsat) of Pd (II) anions averaged 27 mg/g. The Toth adsorption isotherms fairly predicted the equilibrium adsorption of Pd (II) species and the associated surface coverage.The effect of temperature and acid strength of the feed solution on the adsorption of Pd (II) ions were quantified. The adsorption kinetics was limited by external mass transfer since the effect of pore diffusion on the overall rate constant was negligibly small. A pseudo first-order kinetics model was used to describe the adsorption kinetics."

Jan 1, 2003

By M. Barsky, E. Barsky

It is generally accepted that the optimal flow velocity for gravity classification is the final particle settling velocity or, which is the same, the particle spin velocity. However, we have found differences between the settling velocities and the spin velocities of the very same particles. Here we present the results of experiments in a cascading gravitational classifier comprising eleven stages. The feed material was introduced at each stage successively, from the first to the eleventh. The optimal flow velocity was determined for each case. From these experiments it follows that the value of the optimal flow velocity depends to a greater extent on the point of introduction of the feed (i.e., on the design of the device) than it does on the interaction between the solid phase and the flow.

Jan 1, 2003

By M. Eraydin

Dewatering fine particles (e.g., flotation concentrates) is inefficient, energy intensive and often requires large capital and operating costs. To address these issues, a series of advanced dewatering technologies have been developed at Virginia Tech. These include novel dewatering aids and a hyperbaric centrifuge. Typically, the moistures obtained using these methods are 30% to 50% lower than those obtained using conventional methods, as demonstrated in laboratory and pilot-scale test programs. With another novel dewatering technology that has been tested in bench-scale tests, the moistures can be reduced to levels once believed to be attainable only through the use of thermal dryers. In this communication, test results obtained with these advanced dewatering technologies are presented and compared.

Jan 1, 2014

By J. Yianatos

The regrinding stage is necessary to achieve the particle size (liberation) for the final upgrade in the cleaning flotation process. At present, vertical mills (Vertimill) are employed at industrial scale, using small steel balls as grinding media. The regrinding process characterization requires mixing regime knowledge along with the mean residence time of the liquid and solid phases. The residence time distribution (RTD) and the actual mean residence time estimations from theoretical relationships are complex due to the presence of three components (solid mineral, balls and water), mass transport characteristics and segregation affecting solid holdup. Therefore, the experimental RTD determination is suitable for industrial mills. In this work, RTD measurements were performed in two different industrial flotation plants. Both plants operate with Vertimills of 1000-1500 HP in the regrinding process with different circuit arrangements according to the plant treatment capacity. The RTD was measured using the radioactive tracer technique. This technique allows for non-invasive tracer detection where the procedure consists of selecting a liquid (Br82 in aqueous solution) or solid (irradiated solid) tracer for RTD data acquisition in real time. The RTD was modelled by the Large and Small Tanks in Series (LSTS) model, which allowed the characterization of the different mixing regimes for both liquid and solids in the regrinding mills. Effective mean residence times in the range 2-11 min were obtained with RTD shapes similar to those obtained in tumbling ball mills. It was found that residence times of liquid and fine particles were similar, which is consistent with results observed in other mixing systems, e.g. mechanical flotation cells. Also, the mean residence times estimated from the RTD allowed the mass balance adjustment to be validated from metallurgical sampling data. RTD estimations are useful for better understanding the Vertimill behaviour and to identify the actual breakage rates. Keywords: vertical mill, residence time distribution, particle size, modeling

Sep 1, 2012

By K. Gonçalves

One of Vale?s sponsored research project is aimed at the implementation of a practical scale-up procedure for flotation. In this context, detailed flotation kinetics characterization is of critical importance. This work presents the results of a campaign aimed at characterizing flotation kinetic parameters with respect to particle composition. MLA analysis was carried out for 40 narrow-sized iron ore particles with known flotation time from a controlled flotation kinetic test. The iron ore sample studied (59% hematite and 41% quartz) comes from a mine in the southeast of Brazil and the type of reagents applied are the same as used in the plant. For the reagent conditions tested, the overall rougher concentrate (sink) yielded 79.1%, pure quartz and hematite recoveries to the froth were 56.0% and 4.8%, respectively. The results from the kinetic tests show that the flotation rate of the particles doesn?t vary much (~0.03s-1) with composition and that the fraction of floatable particles in each grade controls the separation action. The results show that the rate of flotation is controlled by transport and that the selectivity is controlled by the fraction of floatable particle of each phase.

Sep 1, 2012

By F. K. Ikumapayi

An approach to environmental sustainability and improved process economy, in sulphide minerals production is recycling of process water in flotation of complex sulphide ores, although the chemistry of process water may be a critical issue to flotation efficiency. The influence of major components of calcium and sulphate ions in process water on xanthate collector adsorption and flotation response using pure chalcopyrite, galena and sphalerite minerals were investigated by Hallimond flotation, zeta-potential measurement, FTIR and XPS spectroscopy studies, while bench scale flotation tests were also carried out using complex sulphide ores. The impact of the species in flotation was comprehended using deionised water, tap water, process water and simulated water containing equivalent amount of calcium and sulphate species in process water. Hallimond flotation results showed a decrease of chalcopyrite and galena recovery in process water and also in the presence of calcium and sulphate ions in both deionised and process waters, whereas sphalerite does not respond to flotation. The adsorption of calcium and metal ions but not sulphate ions on the minerals is evidenced by zeta-potential data. FTIR and XPS studies revealed the presence of surface oxidized sulfoxy species and surface calcium carbonates on chalcopyrite in the presence of process water and water containing calcium ions, surface oxidized sulfoxy and carbonate species on galena in the presence of deionised water, process water and water containing calcium and sulphate ions, all at flotation pH 10.5, and these surface species influenced xanthate adsorption. The presence of surface oxidized sulfoxy and carbonate species at the sphalerite flotation pH 11.5 were seen in the presence of deionised water, process water and water containing calcium and sulphate ions, but the surface species does not influence xanthate adsorption. Bench scale flotation using two different complex sulphide ores showed that chalcopyrite, galena and sphalerite recoveries are better in process water than tap water. The studies showed that the process water can be recycled in flotation with no detrimental effect on grade and recovery of sulphide minerals. Keywords: sulphide minerals, flotation, zeta-potential, FTIR, XPS

Sep 1, 2012

By A. Y. Senchenko, S. G. Rybkin, A. V. Aksenov

"Oxidized nickel ores are important source for nickel production in Russia. Considerable explored reserves of oxidized nickel ores with relatively low nickel content, about 0.6-1.4%, are concentrated in the Ural region of Russia. Conventional process flowsheet with the use of blast matte smelting, applied in particularly by JSC “Ufaleynickel”, proves itself as extremely low-margin technology. This paper will examine development of a new more cost-efficient process involving integrated treatment of oxidized nickel ores using the ore from Serovskoye deposit as an example. Target products of this process are hydrate residues containing up to 15 % of nickel and 0.3 % of cobalt, as well as saleable salts of magnesium sulphate and ammonium suplphate. This innovative process includes roasting of a mixture composed of ground ore and sulphuric acid at 650 °?. Sulphate roasted product is then leached in a weak sulphuric acid solution with the following separation of liquid from insoluble solids. Sulphate solution is neutralized by aqua ammonia in two stages until media pH is 3.0-3.5 and 7.5-8.0 with detachment of iron- and nickel-bearing hydrate residues respectively. The mother solution is boiled out resulting in salt crystals which are then dried and roasted at 500-600 °? to obtain magnesium sulphate. The gases generated during salts roasting are captured with production of ammonium sulphate. The developed technology demonstrates higher potential in terms of its economics and eco-efficiency comparing with the conventional process. This innovative technology for integrated process of oxidized nickel ores was patented in Russia.INTRODUCTION Development and industrial implementation of efficient technologies to process oxidized nickel ores is a very important task for non-ferrous metallurgy of Russia. The main reasons for the required technical upgrade of the plants processing oxidized nickel ores is depletion of rich ores, increase of energy resources costs, amplification of environmental and production standards. Due to this, transition from conventional pyrometallurgy to cost-effective hydrometallurgical technologies of ore liberation and solutions processing is logical and corresponds to the worldwide practice of Ni production from oxidized nickel ores."

Jan 1, 2018

By Reza M. Rahman

The froth phase plays an important role in the flotation and upgrading of the final concentrate. At present, the techniques that have been used in the mineral industry to measure the froth recovery have limitations. The aim of this paper is to investigate the performance of the froth in an industrial flotation cell. A unique device has been developed which is capable of decoupling the froth zone from the pulp zone. It consists of two concentric tubes. The inner tube acts as a dropback collection chamber or catcher. The particles that detach from the froth phase fall directly into the catcher and are collected as froth dropback. The froth recovery measurements were carried out in a rougher bank of a copper concentrator treating sulphide minerals. The dropback device is designed so that it can be immersed into a plant size flotation cell and plant froth recovery measurements can be taken at any given time. During the experiments, the bubbles laden with valuable mineral particles entered the device from the plant flotation cell, subsequently rising to form a froth layer at the top of the device. The particles that detached from the froth zone were collected in the dropback collection chamber whereas the concentrate sample was collected by a launder. By drying, sizing and chemical analysis of the concentrate and dropback samples, the froth recovery, was estimated on the basis of the valuable component. The effect of air rate on froth recovery was also investigated. Keywords: flotation, froth, dropback, froth recovery

Sep 1, 2012

By J. Yvon, Inna V. Filippova

"The aim of this work is to seek the inhibitors of the meteoric and bacterial dissolution of sulphides and gangue minerals to stop the undesirable chemical reactions during conservation of the flotation wastes. The approach of passivation of surfaces by chemical treatment of the solid phase is applied for this objective.The samples taken from different depths of an old French waste dump revealed the capacity of the flotation tailings to produce acid waters (pH 1.8-2.4) and to release heavy metals. Mineralogical studies show not only the product of sulphide oxidation, i.e. sulphates, but also the complex transformations of aluminosilicates in acidic liquid phase. The detection by XRD of aluminium hydroxides (gibbsite, boehmite) allows supposing the recrystallisation phenomena during tailings conservation.Comparative tests of the passivation of the surface of sulphide minerals and waste of flotation with using of conventional reagents (CaO, NaOH, phosphates) and original reagents for this purpose (alkyl dithiocarbamates) allow to identify the optimal treatment conditions and the efficient chemicals.Leach tests were carried out in percolation columns during 68 weeks. The normalised leaching tests according to French legislation were run to confirm the selected treatment conditions. The results obtained show that a single treatment with carbamate inhibits the oxidation of the pyrite and the other sulphides, and totally prevents the formation of acid waters (the stabilised pH was 5.3-5.8). Treatment of in situ drainage water allows to obtaining a total precipitation of heavy metals: the residual concentrations of Fe, Cu and Zn are lower than 0,1 mg/l.The passivation of sulphides is the result of the formation with carbamate (studied by IR spectroscopy and XPS) of organometallic compounds, which are stable in acid medium. The presence of thiuramdisulphide (product of alkylcarbamate oxidation) at the mineral surface stabilises the mixed adsorption layer and leads to a considerable reduction in the hydratation rate of surface by avoiding the corrosion of the pyrite. No aluminium was detected in leach solution with this treatment."

Jan 1, 2003

By N. D. Dementieva

Based on lab and pilot-plant tests to recover gold, silver and lead of a Russian deposit, a collective and flotation concentration flow sheet with lead and sulfide concentrates was proposed. The type of the deposit is gold-sulfide-quartz-bearing. The recovery of gold, silver, and lead to a lead concentrate was 47.4%, 68.1% and 70.7%, respectively. The grade of gold and silver grade was 170 g/t and 372 g/t, respectively. The mass percent of lead, zinc and arsenic mass percent was 41.7%, 0.34% and 0.63%, respectively. The recovery of gold and silver recovery to a sulfide concentrate was 50.1% and 28.8% at the grade of gold 20.5 g/t and silver 66.2 g/t. Sulfide concentrate with arsenic mass percent ~3% was biooxidised followed by CIL and obtaining metal at the site as well as zinc concentrate from bioleaching solutions with zinc mass percent 45% at its 64% recovery. The total gold and silver recovery using a developed technology with the account of their treatment at a polymetallic plant was 92.2% and 93.7%, respectively.

Sep 1, 2012

By Jin Duan, Qi Zheng, Bo Yan, Li-cheng Ma, Xiao-kui Che

"The aim of this study was to develop an approach for the selectively removal of Zn(II) from heavy metal-bearing-wastewaters produced by gold chemical industry using magnetic chitosan based adsorbents. Chitosan beads were prepared by cross-linked modification of Fe3O4-chitosan bead using epichlorohydrin as the cross-linker. Both Zn(II) inprinted magnetic chitosan hydrogel bead (Zn-MCHB) and unprinted magnetic chitosan hydrogel bead (MCHB) were prepared and batch adsorption experiments were used to evaluate their adsorption capacities and selectivities. Single adsorption of Cu2+, Pb2+, Zn2+ and Ni2+ showed that both MCHB and Zn-MCHB adsorbs all the four metals and had an affinity in the order of Cu2+ > Pb2+ > Zn2+ > Ni2+. The binary adsorption revealed that the two adsorbents preferentially adsorb Cu2+/Pb2+ from Zn2+-Cu2+/ Zn2+-Pb2+ binary systems. However, MCHB does not show any selectivity in Zn2+-Ni2+ system. In contrast, Zn- MCHB preferentially adsorbs Zn2+ from Zn2+-Ni2+ binary system. Furthermore, the adsorption selectivity is predictable from stability constants of the metals with the amino group of chitosan. The information revealed in this work can be used for further applications in the treatment of wastewater containing a range of heavy metals from the gold chemical industry."

Jan 1, 2014

By Li Tianxia, Zhou Jing, Zhu Yimin

"A typical low-grade of high sulfur bauxite fr contains 54.71% Al2O3, 11.35% SiO2 while the ratio of aluminum and silicon was 4.25, and harmful components such as Fe and S graded 7.3% and 1.33% respectively. The ore is characterized by complex mineral compositions, fine dissemination of particle size of pyrite and diaspore, low desulfurization efficiency, and difficult separation of aluminum and silicon. In order to improve the degree of concentration, recovery and desulfurization efficiency on the basis of process mineralogy studies, the floatation behavior of high sulfur bauxite in the process of desulfurization and desilication were studied through laboratory tests and pilot plant tests. KEYWORDS high-sulfur bauxite; low grade; flotation; desulfurization;desilicication INTRODUCTION In order to solve the selection problem of bauxite mine area, we carried out technological mineralogy, laboratory test, small-expansion Dalian test to solve the problem of the refractory ore. Main research contents and conclusions were presented as followings :(1)Process mineralogy research shows: the main mineral components include diaspore, kaolinite, chlorite, pyrite, limonite. (2)Batch flotation tests indicated that slime can be dispersed well during desulfurization floatation when Na2CO3 was used as modifying agent. (3)Poilot plant tests shows that Batch flotation tests results are correct. 2?PROCESS MINERALOGY 2.1 Chemical Composition of Ore 2.1.1 Spectral Analysis of Sample The results of the semi-quantitative analysis of X-Ray -fluorescence spectra of the original ore are shown in Table 2-1. The results of spectral analysis show that the main components of the sample are O, Al, Si, followed by Fe, Mg, Ti, S and so on, while the content of other elements is very small. The value is Al, and maybe Ti, for bauxite, while Fe and S are unfavorable elements, and Si and Mg and Ca are the main impurity elements."

Jan 1, 2018

By Tchingis Lekhatinov, Lev Filippov, Vyacheslav Severov, Alexandre Matinin, Victor Samyguin, Inna Filippova

"Comparison of flotation efficiency of the new multi-zone flotation cell (MZFC) and different conventional cells was carried out at lab and pilot scales on the various samples: high contrast pyrite tailings and old copper containing tailings. MZFC is a cell of intensive flotation, which provides optimal hydrodynamic conditions for all flotation sub processes. Enhancing of particle attachment, creation of conditions for coalescent flotation, selection of spatially separated zones according to optimal hydrodynamic conditions for flotation sub-processes are proposed as main principles to design an MZFC. The bubbles/pulp stratification was pointed out as a limiting step in the existing intensive flotation machines. Two strategies to improve bubbles/pulp stratification in the MZFC were studied: (a) impact of pulp-bubble jet to the surface of a prismatic insert inside of cell, which provides the detachment of low hydrophobic particles from bubbles, and (b) profiling the pulp/bubbles jet from the reactors due to a specific geometry of cell walls. The new continuous MZFC devices were demonstrated similar or higher efficiency in comparison with laboratory batch flotation cells for pyrite flotation. Higher flotation efficiency (82%) with pure pyrite concentrate (51.2% of sulfur) and a recovery level of 92% was obtained in MZFC when the cell with stratification by impact was used. Similar results were obtained with old Cu-containing tailings. Although MZFC had 1.5 times greater yields of concentrate than a batch flotation cell, it provided the increase of chalcopyrite recovery by 29.4% and concentrate grade by 4.8%. An original organization of pulp/bubbles stratification in the separator part of the new intensive flotation machine using variable geometry inserts allowed the best flotation selectivity with a bubble mineral loading coefficient 1.5 fold higher than the laboratory mechanical or pilot cells."

Jan 1, 2014

By G. Önal

Recovery of nickel and chromite from the tailings has been studied on the samples with 0.214 % Ni and 5.10 % Cr2O3 content and taken from Orhaneli Chromite Concentration Plant. Mineralogical examinations of the samples showed the existence of chromite, olivine, pyroxene, chrysotile, anti-gorite, chlorite, idingite, tremolite and calcite together with trace amounts of millerite, pentlandite, pyrite, pyrrhotite, hematite and limonite type iron oxide minerals in partially serpantinized dunite type particles. In order to recover chromite from Chromite Concentration Plant tailings Mozley Table and Knelson Separator are used and concentrates containing approximately 42% and 46% Cr2O3 are produced respectively with 40% recovery. Most of the nickel remained in the tailings. Therefore, acidic leaching tests are performed in order to dissolve nickel from these tailings. Effects of particle size, acid concentration, temperature, leaching time and solid/liquid ratio on the nickel leaching efficiency are investigated. The optimum leaching conditions are found as 250 g/L acid concentration, 1/5 solid/liquid ratio, 2 hours of leaching time and 60°C temperature, almost all nickel is dissolved at the optimum conditions and acid consumption is about 841 kg/t. Repeated leaching tests are carried out in order to have enough Ni content in the leach liquor for the further treatment of solutions. After repeated leaching tests, leach liquor contains 3 kg/m3 Ni, 48 kg/m3 Fe, 2.2 kg/m3 Si, 23 g/m3 Cr and 590 kg/m3 H2SO4. Ni is recovered from that solution by precipitating with H2S followed by HNO3 dissolution and precipitating Ni as hydroxide with 63% Ni content. Leach cakes are subjected to the gravity separation (Mozley table) to recover the remained chromite and a chromite concentrate with 47% Cr2O 3 content is produced with 53% recovery. As a result of the abovementioned tests, a conceptual process flow sheet is proposed for the treatment of these chromite concentration plant tailings.

Jan 1, 2014

By M. Saba

In cyanide leaching procedure, achieving an acceptable efficiency for silver and gold is very time-consuming, thus, enough studies have not been performed for optimization and modeling of this process. The kinetics of cyanide leaching includes two steps: first step comprises a sharp slope while the other has a slight increasing trend. In the present study, in order to reduce the time and cost, the cyanide leaching process of a sulfide silver/gold ore was optimized in the first period. The applied parameters and their ranges are: temperature 20-40 (°C); time 1-8 (hrs); cyanide concentration 1-2 (mole cyanide / mole Cu); the percentage of solid to liquid 1-2 (%) and pH 10-12. For design of experiments fractional factorial 2(5-1) was used. Also four center points were applied to increase the accuracy of the model. In addition, by analysis of variance (ANOVA) the most effective parameters were identified and the optimized condition was determined. A regression model was proposed to describe the effects of independent variables and their interacting role on silver recovery. Results showed that the model was linear for silver and nonlinear for gold. In the gold recovery process, the two important parameters are time and pH with the former being more effective. Due to the existence of cyanide ions in the medium, temperature and cyanide concentration have less influence in the gold recovery process. Solid to liquid ratio, in addition, comprises a slight negative impact on the procedure. This emphasizes the different kinetics of silver/ gold cyanide leaching. Finally, using the optimum condition the amount of silver and gold obtained were 61% and 67% in 8 hours, respectively. While in general conditions, the results were 37% and 54% in 24 hours, respectively. Keywords: cyanide leaching, refractory gold/silver ore, modeling, optimization

Sep 1, 2012

By Kym Runge, Wei Huang, Fengnian Shi, Christian Antonio

"This paper presents an emerging High Voltage Pulse (HVP) technology for ore pre-treatment. Unlike previous studies where HVP was utilized as a crusher to pulverize ore particles to micron size ranges for downstream processing, the researchers at the Julius Kruttschnitt Mineral Research Centre (JKMRC) use HVP to enhance ore processability. Application of relatively low levels of HVP energy to selectively break mineralized particles from barren rocks, followed by size-based screening separation enables the feed ore to be split into high grade and low grade products. During HVP treatment, cracks/micro-cracks are generated which results in pre-weakening of the treated ore particles, which ultimately results in energy savings in the downstream comminution processes. HVP treatment followed by conventional grinding also results in improved liberation of the valuable minerals in comparison to that achieved with traditional conventional comminution, subsequently improving downstream separation efficiencies. The three major improvements in ore processability through HVP pre-treatment have the potential to facilitate rejection of low grade ore prior to processing, increase production rates, reduce the energy required for comminution and improve flotation separation recoveries. This paper summarizes the major research outcomes of HVP pre-treatment demonstrated using ores from various mining operations conducted by the JKMRC. It also discusses the barriers that must be overcome before it can be adopted by industry with confidence in a continuous high tonnage rate application.INTRODUCTIONThe challenges of declining ore grades and increased plant throughput rates, resulting in higher energy consumption and operational costs, require the mining industry to adopt new technologies to make future ore treatment economically viable. Over the past 50 years, many researchers have engaged in investigating novel comminution techniques. Since Yutkin (1955) first demonstrated the potential to generate shock waves with pressures exceeding 103 MPa via electrical breakdown of water, several applications of electrohydraulic crushing by shock waves have been reported (Curley-Macauly, 1968). Interest in this technique was bolstered when Andres (1977) demonstrated that electrodynamic fragmentation results in superior liberation of mineral grains as compared with conventional grinding techniques. Despite mounting laboratory-scale evidence of the efficacy of electrodynamic fragmentation for mineral liberation, development of the technology for full-scale operation has stalled, primarily because the energy required to achieve desirable mineral liberation is approximately two to three times that of mechanical comminution, amounting to approximately 100 kWh/t for typical mineral ores (Andres et al., 2002)."

Jan 1, 2018

By G. N. Jadhav

In India, bauxite deposits are concentrated in Central India, Western Ghats and Eastern Ghats. Bauxites from various regions in Gujarat were identified during the present investigations of geochemical mapping. Different types of Bauxites samples were collected from Kachchh, Jamnagar, Porbunder, Junagarh, Bhavnagar and Amreli areas of Gujarat state and were studied in detail for their geochemical signatures to plot the data on Geochemical map. Raw bauxites were characterized by using powder XRD, XRF, ICP and optical microscopy techniques (with the help of Model microscope having both transmitted and reflected light setups) and were later examined to grade their quality. Most of the bauxites from Kachchh region were of high-grade (gibbsitic) type; while those of Sourashtra region were of low-grade (lateritic / calcitic) types. Most of these bauxites were either of ferruginous/lateritic or of calcareous/calcitic types. Based on the mineralogical composition, such as gibbsite, hematite and/or goethite, Kaolinite and calcite minerals present in particular bauxites, the deposits were graded. Finally, the Geochemical mapping of Bauxites for Gujarat region was prepared and discussed.

Sep 1, 2012