Search Documents

By Mohammad Mainul Hoque, Linhan Ge, Ai Wang, Geoffrey Evans, Subhasish Mitra

"Dispersed phase interactions involving bubbles and particles in the turbulent environment play a significant role in the flotation process. The conventional collision models only account for the deterministic rather than the stochastic behavior of turbulenct flow. What the bubble-particle collisions would be like remains an open problem due to the complex nature of turbulent flow. To address this research question, the present study aims to quantify the bubble-particle collision efficiency incorporating turbulence using the computational method. Multiple solid particles were released to interact with a single stationary rigid bubble (non-deformable interface). Effect of particles Stokes number, turbulent intensity (TI) and integral length scale on the bubble-particle collision efficiency (Pc) was examined. Large Eddy Simulation method (LES) was used to compute the continuous phase. Fluctuating velocity required at the inlet boundary condition was derived from Gaussian energy spectrum to generate the upstream turbulence. Discrete Phase Model (DPM) is used to simulate particle trajectory. The characteristics of turbulent flow were analyzed through Energy spectrum and energy dissipation rate. The critical initial releasing radius of the annulus, where Pc equals zero, reaches up to 1.5(Rb+Rp) under high turbulent intensity (TI) 20.48% compared to 0.23(Rb+Rp) calculated from the traditional Pc model. Pc decreases as the distance of initial releasing annulus between bubble centre increases. Pc increases as particle Stokes number increase up to 0.66. The collision efficiency for particles of St less than 0.38 is higher under TI 11.78% compared to TI 4%.INTRODUCTION To increase mineral recovery, interactions between bubbles and particles are essential. All flotation devices achieve it through introducing some level of turbulence into the system by increasing specific energy dissipation rate. Figure 1 shows three different flotation equipment, traditional floatation cell, Concorde cell and cyclonic-static micro-bubble flotation column (FCSMC), with different turbulence generation mechanisms – impeller, down-flow liquid jet and pump recirculation, respectively."

Jan 1, 2018

By D. W. Feng

Thiosulfate leaching has been considered as the most promising alternative to cyanidation for the recovery of gold from ores. The chemistry of the ammonia-thiosulfate-copper system is complicated due to the simultaneous presence of complexing ligands such as ammonia and thiosulfate, the Cu(II)-CU(I) redox couple and the stability of thiosulfate in solution. However, acceptable gold leaching rates can be achieved by maintaining suitable concentrations of thiosulfate, ammonia, cop-per and oxygen in the leach solution. The leaching of gold in thiosulfate solution is an electrochemical reaction involving the oxidation of gold to gold thiosulfate and the reduction of Cu(II) to Cu(I). Previous studies have shown that the reaction rate of gold was much higher in the presence of am-monia thiosulfate than corresponding sodium thiosulfate. This indicates that cations may affect the anodic oxidation of gold in thiosulfate solution. The present study utilises electrochemical tech-niques to study the anodic oxidation of gold in thiosulfate medium in the presence of the different alkali metal and alkaline earth metal ions. It has been shown that the presence of the heavier cations such as potassium, calcium, and caesium enhance the oxidation of gold in thiosulfate solution. Leaching tests also indicated the improved recovery of gold from a sulfide ore with the addition of heavier cations. XPS results demonstrated that the binding energy for gold shifted to lower values in the presence of the heavier cations, indicating the ready formation of ion-pair with gold thiosulfate at the gold surface during adsorption.

Jan 1, 2014

By E. Emelyanenko, P. Solozhenkin, J. Yagudina, O. Ibragimova

To recover tetrahedrite-tennantite series minerals from porphyry copper-pyrite ores by the froth flotation method, further research on thiol collectors is launched to promote the utilization efficiency of copper ores. In the present paper the adsorption mechanism of the collectors on tennantite surface has been investigated by computational modeling and FTIR-spectroscopic analysis, which have revealed that the decrease in prognosis of collector activity evaluation (PCAE) for tennantite is in the following order: BX (-0.34318), AEROPHINE 3418A (- 0.61756), AERO 5100 (-14.18857). The lower PCAE the stronger the ability of the collector to interact with the mineral surface of tennantite and form the stable complex. More kinetic reliable conditions to form suitable adsorption layer and rupture of the liquid interlayer with AERO 5100 have been observed by FTIR spectra due to decrease of the intensity and stretching and bending vibrations of water (less than 20 and 65%, respectively). In order to verify the feasibility of AERO 5100 as a collector the industrial flotation tests have been conducted. Flotation performance has improved significantly with the stadially grinding and preflotation of tennantite in intercycle copper flotation that allows to avoid desliming of the fragile mineral and minimize loss of Cu and As in tailings. The recovery of copper in copper concentrate increases by 3.9% with the grade maintained.

Jan 1, 2018

By P. Somasundaran

Treatment of mineral surfaces with appropriate surfactants plays an important role in mineral processing operations such as flotation, flocculation and dewatering. Recently biosurfactants, in particular, have received a considerable amount of attention because of their unique surface active properties and biodegradability. In this work we examined the performance of biosurfactants, sugar based alkyl glycosides and sophorolipid esters as reagents to control the hydrophobicity of minerals with selectivity of adsorption on mineral surfaces for flotation applications. It was discovered that n-dodecyl-ß-D-maltoside adsorbs on alumina, titania and hematite but, interestingly, not on silica. The hydrophobicity obtained is governed both by the surface coverage as well as the nanostructure of the adsorbed layer in terms of orientation of the adsorbed species. Surprisingly, even though the above surfactants are non-ionic, their adsorption was pH-dependent. We have correlated this pH dependence to the type of species on the mineral surface. Also it is shown that mixing of these surfactants with traditional ones can help reduce the carbon footprint due to synergy between the reagents and help selectivity due to antagonism. The experimental results were analyzed to get information on optimal pH and dosage conditions, for mineral surface modification. The study provides guidance for mineral treatments using biosurfactants and the potential use of these next generation reagents in mineral processing.

Jan 1, 2014

By H. Y. Ran

Magneto-flotation is a recently developing technology of mineral processing. This technology combines the traditional magnetic separation with flotation and provides a magnetic and buoyant force compound field to separate different minerals based on the differences of magnetism and floatability between useful minerals and gangue minerals. Magneto-flotation is applicable to separate ferromagnetic from nonmagnetic minerals, especially to separate magnetite from floatable gangue minerals. This magneto-flotation column is equipped with pulse electromagnetic field in the middle upper part, a bubble producer and upwell water inlet in the bottom. The pulse time of electromagnetic field in the column can be optionally adjusted and the maximum intensity of pulse magnetic field can reach 35mT. Pulse magnetic field can not only restrain magnetic minerals from entering into the froth layer, but also destroy the magnetic agglomeration to ensure a higher recovery and a higher concentrate grade. The results of experiments with magnetite show that pulse magnetic field has remarkable influence on flotation process. Compared with single flotation, magneto-flotation column can improve the recovery of magnetite by ten percent. After one time?s magneto-flotation processing, the grade of iron concentrate can increase from 65.4% to 69.5%, the content of silicon oxide in iron concentrate decreases from 7.4% to 2.8%, and the total recovery is above 96%.

Jan 1, 2014

By Z. T. Yuan, S. L. Qi, Q. Y. Meng, G. X. Zou, L. X. Li, J. W. Lu

"The selective separation of pentlandite from serpentine was investigated using the magnetic coating-magnetic separation by conditioning slurry pH value, stirring speed, magnetic field intensity and controlling dosages of sodium hexametaphosphate (SHMP) and sodium oleate (SO). The optimal conditions were obtained as follows: the natural pH of 6.8-7.2, stirring speed of 2300 rpm, magnetic field intensity of 200 kA m-1, SHMP of 60 mg L-1, and SO of 400 mg L-1. Results showed that the Ni grade was 21.4% with the Ni recovery of 81.4% and MgO content of 3.8%. FTIR indicated that coagulant of SO preferentially adsorbed onto pentlandite and magnetite particles while hardly adsorbing onto serpentine particles when dispersant of SHMP was used. Thus, the selective magnetic coating of magnetite on pentlandite surfaces could be formed due to the formation of hydrophobic surfaces on pentlandite and magnetite particles. Calculations of DLVO (Derjaguin-Landau-Verwey-Overbeek) confirmed that interactions between magnetite and pentlandite particles were much stronger than that between magnetite and serpentine due to the existence of hydrophobic interactions with the addition of SO. Consequently, the pentlandite was successfully separated from serpentine. Therefore, this study exhibits the potential to separate pentlandite from serpentine minerals for practical applications and thus deserves further study.INTRODUCTION It has been well known that the separation of pentlandite from serpentine is a worldwide challenging issue in the processing of sulphide nickel-copper ores. Because the serpentine mainly causes the high pulp viscosity and slime coating on the pentlandite, which interferes with the flotation process of pentlandite (Cao et al., 2016; Feng et al., 2012). The fibrous mineral of serpentine preferentially attaches to the air bubble, forming bubble-macrofibers aggregates, which are easily floated into the nickel concentrates, resulting in the decline of Ni grade (Alvarez-Silva et al., 2016; Kusuma et al., 2014). In addition, the serpentine adheres to the pentlandite as hetero-aggregation or slime coating via the electrical interaction between a positively charged serpentine and a negatively charged pentlandite, which decreases the hydrophobicity of pentlandite and reduces the collector adsorption (Feng et al., 2013). In other words, the presence of serpentine or the occurrence of aggregates (including slime coating and bubble-macrofibers aggregates) seriously affects the flotation process and deteriorates the flotation of pentlandite. Therefore, we propose magnetic separation to recover pentlandite from serpentine with the magnetic coating technology, which is different from forth flotation."

Jan 1, 2018

By Axel Pankewitz, Andrew Smith, Mathias Stender, Christian Behrens

"Particle size measurement is one of the most important factors in obtaining peak performance of the mineral processing plant in order to ensure efficient milling and flotation circuit operation. Off-line particle distribution analysis technologies only allow an infrequent check of the ore slurry size and hence do not allow for timely process monitoring or intervention. Most existing on-line particle size analysers suffer from a variety of disabilities such as poor statistics, non-representative sampling or mechanically complex setup. This paper will describe an Ultrasonic Extinction based method which overcomes many limitations of existing online analysers and has proven its performance for mineral applications over many years. Installation examples will be given. Since new technologies usually raise e questions about comparability and agreement to common particle size analytical methods e.g. sieving or laser diffraction analysis, extensive studies were performed comparing these different technologies to quantify the quality of results as well as its mathematical robustness."

Jan 1, 2014

By S. Cagirici, Z. Öztürk, A. Hassanzadeh

Many flotation kinetics models have been studied in the literature. Their applicability was extensively investigated and argued in detail. However, model selection criteria were not adequately discussed from the statistical points of view. In this investigation, the kinetic behavior of a complex copper sulfide ore was studied in a mechanical Denver flotation cell focusing on flotation kinetics of chalcopyrite, pyrite and molybdenite. Different flotation kinetics models including nine common empirical models and four mathematical models namely Hill, Chapman (Sigmodial function), single rectangular (Hyperbola equation) and exponential were applied to the experimental data. In addition to assessment of the goodness of fit criterion for each model, a factor of model complexity was considered using information criteria (IC) (i.e. Bayesian information (BIC), low of iterated logarithm (LILC) and Akaike information (AIC) indices). The obtained results showed that the IC indices could simply manifest the best-fitted model to the experimental data. Whereas, the coefficient of determination values (R2) were relatively same for all models. By taking the R2 and model complexity criteria into account, the exponential model was chosen as the best representative mathematical model to demonstrate chalcopyrite kinetic behavior. However, Chapman model was selected as the best one for the flotation of pyrite and molybdenite. In case of the common first-order flotation kinetics models, fast and slow flotation kinetic model (Kelsall) was reasonably fitted the best to the given data of chalcopyrite. However, the gas/solid kinetics adsorption model was chosen as the best-fitted one for pyrite and molybdenite. Furthermore, it was found that mathematical models represent better results in association with flotation kinetic behavior of chalcopyrite, pyrite and molybdenite due to the consideration of more parameters in modeling. Finally, it was concluded that the IC indices must be applied to the process of model selection due to consideration of goodness of fit, complexity of a model and model consistency.

Jan 1, 2018

By Agnieszka Surowiak, Tomasz Niedoba

The paper presents a way of determining relations between ash content in coal, particle size and particle density by means of regression, multidimensional Morgenstern distribution functions and kernel approximation. The three-dimensional random vector (D, ?, ?), where D is a random variable describing particle size, ? - random variable describing particle density and ? - random variable describing ash content, where function ?=?(d, ?) is obtained by means of regressive function. The multidimensional Morgenstern distribution functions and kernel estimators with the use of Gauss function were applied to approximate the functions f(d, ?, ?) and f1(d, ?). This approach is a new way of multidimensional description of grained materials such as coal and it also allows to evaluate material features more properly than the classical statistical approach. The results were verified statistically.

Jan 1, 2014

By Hao Zhang, Dezhou Wei, Qiang Zhao, Caie Zhang, Baoyu Cui, Xuetao Wang

"Nowadays, long periods of relatively low iron ore prices have made the steel industry get the greater pressure. To develop appropriate processing technology based on characteristics of the iron ore, so as to reduce the beneficiation costs, is crucial to the improvement of iron and steel enterprise competition. For a typical low-grade iron ore from northeast China, beneficiation process research was conducted based on the in-depth studies of ore characteristics. Results show that the iron grade of the ore was 31.56%, the content of FeO was 6.59%, the main iron minerals were hematite and magnetite with fine dissemination sizes and partly scattering in gangue; With the grinding fineness of 65% passing 0.074mm, and regrinding fineness of 90% passing 0.074mm, the concentrate with 66.80% iron and recovery of 82.90% was obtained via the combined flowsheet of stage grinding – classification – gravity concentration – low and high intensity magnetic separation – reverse flotation. Ratios of gravity concentration and low intensity magnetic separation were 70.21% and 7.57% respectively in 40.42% of total concentrate yield; The loss of micro-size fractions can be reduced by feeding spiral tailings into magnetic separation and flotation; It’s helpful in reducing the dosage of reagents and beneficiation costs by increasing the throughput of gravity concentration and outputting concentrate of low intensity magnetic separation.INTRODUCTION Iron and steel industries are facing the increasing pressures in the continued falling iron ore prices. In order to improve the competitiveness, it is extremely urgent for them to develop more appropriate separation process for the reduction in iron ore beneficiation cost. As a typical low-grade iron ore, Anshan-type iron ore is one of the most important iron ore resources in China [1-3]. The flowsheet of stage grinding and separation contained the classification of the coarse particles and the fine particles, the gravity concentration, the magnetic separation and the anionic reverse flotation has been widely applied for Anshan-type iron ore. With the appropriate separation progress as well as equipment, satisfactory separation results had been obtained, and mineral particles with different size were recovered separately [4-7]. However, the low recovery of fine mineral particles and the relatively high beneficiation costs still prevented the efficient application of the process [8]. For a Anshan-type low-grade iron ore, a typical process flowsheet, as mentioned earlier, with stage grading, classification of the coarse particles and the fine particles, gravity concentration, magnetic separation, anionic reverse flotation was adopted currently. And the concentrate with 67.10% iron and recovery of 75.50% was obtained and the gravity concentrate accounted for 39% of the total concentrate. However, a large amount of fine liberated iron ore particles were lost in the tailings."

Jan 1, 2018

By I. N. Gridasov, V. V. Khromov, R. I. Ismagilov

"Over 50 mln.tonne is the average annual output of oxidized ferruginous quartzites typically containing Fe38-42% mined in Mikhailovskoye ore field. The most promising and cost-effective way to expand concentrate production maintaining current output of magnetite is processing of oxidized ferruginous quartzites (hereinafter referred to as OFQ) mined as a by-product in Mikhailovsky open pit mine. However lack of proven and efficient concentration and agglomeration process applicable to OFQ and insufficient data for feasibility evaluation of OFQ processing encumbered full-scale addressing of this challenge. Based on outcomes of multiple various studies a process of OFQ flotation was designed by MC Metalloinvest LLC and PJSC Mikhailovsky GOK engineers. Comparative lab-scale testwork have proven performance and production advantages of flotation against magnetic separation feat. flotation and combined concentration method. Lab-scale flotation enabled production of concentrate with average Fe66.6% and SiO22.06% grade. Geologic and production contouring of OFQ deposited in Mikhailovskoye ore field has been carried out to collect necessary data for feasibility study incl. cost and profit estimation. As a result processing and production properties of over 3,500 samples have been analyzed which is characteristic of every direction and level of prospective ore mining within Mikhailovskoye ore field up to year 2032. Following work has been done based on geologic and production contouring of OFQ: – natural typification of ores and production (processing) grades of OFQ, determination of average mineral composition; – correlation analysis of interrelation between OFQ mineral composition and processing features thereof for overall bulk of samples as well as for individual data blocks related to various directions of open pit mine; – OFQ classification with account of defined mineral composition and processing features. Total Fe weight content in chamber product of flotation (known as concentrating ability in flotation) was applied as a major differentiating factor for processing grade classification of OFQ. Three processing grades of oxidized ferruginous quartzites were established as a result of flotation tests run to determine concentrating ability, i.e. – hard concentrated OFQ (TO) – below Fe65%; – mean concentrated OFQ (SO) – Fe65-67%; – easy concentrated OFQ (LO) – over Fe67%. Outcome of this work provided initial data for feasibility study and cost-profit evaluation of medium-term industrial-scale processing of OFQ deposited in Mikhailovskoye ore field."

Jan 1, 2018

By A. Qaredaqi, M. Mohammadi

Wet High Intensity Magnetic Separators, for short, WHIMS are used for recovery of Iron ores with low magnetic susceptibility. A Jones patent WHIMS with "grooved plates" matrix is being used in Dry Tailing processing line in Hematite Recovery Plant at Golgohar mining & Industrial Co. for recovery of Hematite. In this kind of separators Matrices are used for increasing the Magnetic field intensity and providing high magnetic field gradient. The laboratory WHIMS in Golgohar Iron Ore and Steel research Institute is capable to provide a background magnetic field strength up to 0.85 Tesla and in presence of ‚expanded metal? matrix, magnetic field intensity could increase up to 0.9 Tesla. More than 50% of feed particles in this separator were finer than 36 micron and recovery of these particles needs more magnetic field intensity. Hence, ‚Grooved Plates? matrices with Js= 2 Tesla and 3.8 mm gap were constructed. Measurements indicated that magnetic field intensity around the matrix will increase to 1.25 Tesla. Graph of Magnetic field intensity around the matrix to background magnetic field intensity was plotted and a model with Rsquare= 0.9 was offered. In addition, magnetic field gradient and magnetic force were calculated. In WHIMS with feed top size of 150 micron, the main effective forces on separation process are the magnetic force and the hydrodynamic drag force. With assuming that the particles are smooth and spherical and the flow is laminar, Recovery of fine magnetic particles is problematic in this separator because of drag force. Considering these facts and mentioned model, finest particles that are recoverable in different magnetic field intensities were calculated. Computations illustrated that with magnetic field intensity more than 0.8 Tesla, particles as fine as 4 micron are theoretically separable but it should be noted that in practice a larger attractable particle size would be expected.

Jan 1, 2014

During incineration of municipal solid waste (MSW), some heavy metals and other environmentally harmful elements are liberated into bottom ash. The stricter environmental regulations require a higher immobilization efficiency of the ash before its safe disposal and application. Vitrification is one of the promising options, and has the advantages of high destruction efficiency of organics, high immobilization of heavy metals, and large volume reduction. The main components of the vitrified slag are SiO2, CaO, Al2O3, Fe2O3, Na2O and MgO, and the compositions have direct effect on the glass formation during vitrification, and further on the physical and mechanical properties of the slag. To provide essential data for the utilization of bottom ash as vitrified slag, the phase relations and thermodynamic properties of the oxide system need to be systematically investigated. In the present study, the liquidus temperature of the typical vitrified bottom ash slag was determined by using differential scanning calorimetry (DSC) measurement. High temperature equilibrium experiments were conducted to investigate the phase relations of the sub oxide system of CaO-SiO2-Na2O by means of Scanning Electron Microscopy (SEM), Electron Microprobe Analysis (EMPA) and X-ray Diffraction (XRD). The results show that the melting temperature of the vitrified bottom ash is around 930°C. In the CaO-SiO2-Na2O system with less than 50 mol% SiO2, the liquidus temperature de-creases with increasing amounts of Na2O along the tie-line of Na2O-Ca3Si2O7. Two compounds Na2Ca3Si2O8 and Na4Ca8Si5O20 are identified in the oxide system.

Jan 1, 2014

By D. Whittles, S. Kingman, S. Bradshaw, N. Miles

The influence of microwave energy at high electric field strength on ore strength has been investigated. Two ores of varying mineralogy were treated in both multimode and single mode microwave cavities. After treatment, any change in strength relative to untreated ore was established. It was shown that in the multimode cavity reduction in strength was related to the applied power level. Results of tests carried out in the single mode cavities showed that, for both ores, reductions in ore strength > 50% could be achieved in very short periods (<1 second). Thermal stress analysis showed that the mechanism of microwave induced failure was the development of tangential stresses at the grain boundaries. It was concluded that operation at 915 MHz with high power and short residence times gives feasible scale-up possibilities.

Jan 1, 2003

By H. Kasaini

Batch wise adsorption tests for platinum (Pt) on the surface of activated carbon pellets (Norit RO 0.8 BET surface area 1100 mg/g) were carried out in mixed chloride solution. The purpose of this study was to assess and compare the adsorption performance of amine-treated activated carbons (AACs) and native activated carbons (NACs) in terms of adsorption capacity and selectivity. The effect of pH and temperature on adsorption capacity and selectivity was established. The amine- treated ACs were prepared by anchoring the amino groups (butyl amines) on the surface of AC pellets in aqueous media and the UV-Vis was used to determine the amount of amine sequestered from solution by ACs. The dosage of butyl amine on the surface of ACs averaged 0.15 g/g, carbon. The adsorption mechanism was described by the ionization and complexation model whereby interaction between the protonated AAC surface and the anionic chlorocomplex ions (PtCl5 [H2O]-, PtCl62-) proceeded by either electrostatic attraction or/and by covalent bonding [(NH3)2PtCl6 or (CH2COO)2PtCl6]. By comparison, the adsorption capacities of Pt on amine-treated ACs and native ACs were 53.8 mg/g and 33.03 mg/g, respectively which highlight the benefits of anchoring functional molecules on ACs. The selectivity of AACs was influenced by solution pH. Pt adsorbed selectively on the surface of amine-treated ACs at pH<1.5. The highest separation factor that was recoded pertained to Pt and Fe species (ßPt/Fe = 90) then followed by Pt and Ni species (ßPt/Ni = 30) or Pt and Cu species (ßPt/Cu = 15). The lowest separation factor was recorded for Pt and Cr ions (ßPt/N= 5). Adsorption kinetics of Pt on amine-treated AC surfaces, according to the first and second order reactions, were investigated and results showed that rates were in the order 10= 5). -4 min-1 and 102 g?min/mg, respectively. The pseudo 1st order kinetics predicted the adsorption capacity of 51.81 mg/g which was almost similar to the experimental value (53.8 mg/g) while the second order rate equation predicted Pt adsorption capacity of 40.1 mg/g. Both The Langmuir and Toth isotherm fitted the Pt adsorption at pH < 1.0. The Freundlich isotherm tended to underestimate the adsorption capacity of AACs.

Jan 1, 2014

By A. M. Raichur, S. P. Vijayalakshmi

Fine coal dewatering is a major problem in the coal industry because the fines hold significant amounts of water and account for two-thirds of the product surface moisture. Present methods include flocculation using polymeric flocculants followed by filtration. But the kinetics of filtration are not favorable with such flocculants. In this study, a novel method involving flocculation with microorganisms for improving the settling rates and dewatering kinetics has been investigated. Two Gram-positive microorganisms, Mycobacterium phlei and Bacillus subtilis were used as bioflocculants. The effect of time, pH and ionic strength of the electrolyte used on adhesion and flocculation were studied. Adhesion tests showed that maximum adsorption occurred in 20 minutes in the pH range of 2-7 and the total amount of bacteria adsorbed was almost the same with both the flocculants. Nearly 98% of the coal flocculated with both the microorganisms in about 5 minutes. The filtration rate of fine coal almost doubled with addition of bacteria and electrolyte and maximum filtration occurred near the point-of-zero-charge of the bacteria.

Jan 1, 2003

By G. Venkateswara Rao

The multi-gravity separator (MGS) is a novel piece of equipment for the separation of fine and ultra-fine minerals. However, the published literature does not demonstrate its use in the separation of Iron ore fines. Therefore, an attempt was made to study the effects of different process variables on the performance of an MGS for the beneficiation of Iron ore fines. The results obtained from this study revealed that among the parameters studied, drum rotation, amount of wash water and angle of inclination play dominating roles in controlling the yield and grade of the Iron ore. The majority of the newly developed Multi gravity concentrators have tremendous potentials for various applications. Therefore, the performance evaluation of these concentrators treating various minerals, coals, heavy metal recovery from tailing dams, etc., have become an active research topic. Several attempts have also been made to develop appropriate mathematical models of individual concentrators. Despite all these efforts, these concentrators have yet to find the widespread applications they deserve. The ?as received? sample assayed 40.80% Fe, 40.90% SiO2,0.24% Al2O3and 0.20 % LOI and all other trace elements within the specified range. The current paper deals with the Mineralogical studies, characterization and process amenability studies of Sub grade Iron ore from Deposit No. 5, Bacheli complex of Bailadila using Multi Gravity Separator (MGS).

Sep 1, 2012

By Ernesto de la Torre, Karla Velín, Alicia Guevara

"The following study shows the improvement and simulation of a gold recovery plant of 24 t/day of capacity by gravity concentration, flotation and leaching. The ore processed had grades of 6 g/t Au, 15 g/t Ag, and 0.69 %Cu with the mineralogy consisting of 2 %chalcopyrite, 12 %pyrrhotite, 7 %plagioclase and 50 %quartz. The recovery process starts with crushing the ore followed by grinding it further in a ball mill. The ground ore is then concentrated in a Falcon centrifugal concentrator with concentrate being processed by amalgamation process. Gravity tails are sent to a flotation circuit where the copper minerals and some gold are concentrated. Lastly, the flotation tailings undergo cyanidation for gold recovery. Currently, the overall recoveries are 82.8 %Au, 49.6 %Ag and 99.1 % Cu. The optimization was developed in the laboratory using a Wilfley table by gravity concentration. Flotation tests in the laboratory were performed using potassium amyl xanthate and pine oil. Lastly, cyanidation was then performed on the flotation tailings. The results showed the optimum concentration of sodium cyanide in cyanidation is 2 g/L, which produced an increase in gold recovery from 30% to 44%. The reduction of diameter particle from 132 to 80 µm also produces an incremental recovery of gold and silver from 11% to 21% Au and 0.4 to 3% Ag in gravity concentration. Likewise in the cyanidation the recovery of gold and silver has shown a rise from 44 to 62% and 8 to 32% for Au and Ag respectively. However, the flotation method the gold recovery is reduced from 68 to 30% Au by reducing the particle size. Computer simulations using the programs, Moly-Cop and ModSim were performed to determine optimum parameters for the recovery of precious metals at the gold recovery plant."

Jan 1, 2014

By Wei Sun, Ruolin Wang, Jianjun Wang, Xiaodong Li, Honghu Tang, Yuehua Hu, Anh V. Nguyen, Haisheng Han, Kefeng Chen, Zhao Wei

It is difficult to separate scheelite especially from fluorite with fatty acid collectors because the adsorption mechanism of these collectors occurs through chemisorption of the oleate ion onto the mineral surface. A simplified flotation process using Pb-BHA complexes was developed to replace the energy-inefficient Petrov’s process of using a fatty acid, increasing the recovery of scheelite and reducing the cost. The relationship between surface chemical properties (crystal chemistry, solubility, and Zeta potential) of minerals and flotation by using a fatty acid or Pb-BHA complexes was studied in detail to provide new insights into the selective separation mechanism. The results indicate that the scheelite surface exposes more O atoms than Ca and that they are negatively charged due to the anisometric dissolution of Ca and WO4, which provides the possibility for separation using selective interfacial reaction. The FTIR and Zeta potential results indicate that both chemical and electrostatic adsorption play an important role in the adsorption of Pb-BHA complexes on the scheelite surface. The XPS results of the atomic composition and binding energies confirmed the presence of the adsorbed Pb-BHA complexes and that O and Ca may be the active adsorption sites. Therefore, scheelite was able to be collected by forming either a Ca-O-Pbcollector or W-O-Pb-collector (BHA). However, fluorite was only able to be collected by a fatty acid collector and colloidal [H2SiO3]n -, and a high temperature was needed improve the selective desorption of the adsorbed fatty acid collector by forming Ca-[H2SiO3]n - on the fluorite surface, resulting in serious problems in industry. However, the Pb-BHA complexes significantly contribute to improving the recovery of scheelite minerals, simplifying the flotation process, and circulation of the residual reagents and water. The new process has been applied in Shizhuyuan Mine, and improved the recovery by almost 10%.

Jan 1, 2018

By G. Sedelnikova

This paper is aimed to elucidate the problem of copper losses in pyrometallurgical slag. Currently, flotation is used to recover copper from the slag and return the metal into the pyrometallurgical process, but the percentage of recovery frequently remains unacceptable. The process of copper leaching from the slag flotation tailings using biologically regenerated ferric sulfate is considered here as an approach to the issue. A sample of the slag flotation tailings containing 0.67% Cu and 4.99% Zn was supplied by the Urals Mining and Metallurgical Company (UGMK, Russia). The Cu and Zn speciation analysis of the sample demonstrated that Cu occurred as 58.1% oxide, 15.4% native Cu, and 18.1% secondary sulfides whereas chalcopyrite proportion was as low as 8.4%. Prevailing Zn species were refractory (58.9% Zn ferrite), and zinc oxide and silicate species made just 37.2% of the total metal content. The silicate generated silica gel that strongly hampered filtration. As demonstrated, Cu recovery is a possibility, which is apparently not the case with Zn. In this work, the stirred tank bioreactor acid leaching employing bacterial Fe3+ sulfate solutions was studied, with ferric sulfate being a product of Fe2+ biological oxidation and not the chemical reactant adding of Fe3+ sulfate. Acidithiobacillus, Sulfobacillus, and Leptospirillum bacilli were employed in Fe2+ biooxidation. Temperature, pH, Eh, S:L ratio, leaching time, and Fe3+ concentration in the source leachate as the process controls were considered. As demonstrated, the process employing biologically regenerated ferric sulfate proved to be more efficient than conventional chemical leaching. Under the optimum conditions, the proportion of Cu extracted into leachate during 2 hours was 79.1%, and that of Zn 27.2%. Precipitation of high-grade Cu sulfide served to extract the metals from the leachate, and Cu extraction was 99.7%. All in all, 23.2% Cu, 0.03% Zn, and 0.02% Fe was returned into the pyrometallurgical process. Keywords: slag flotation tailings, copper leaching

Sep 1, 2012