Search Documents

By Meeok Kim, Paul Beljan, Gordon Chen

"Clinton combined sewer overflow storage (CSO) facility project developed by the Department of Water Environment Protection of Onondaga County, New York, is to improve sewer facilities and infrastructure in Syracuse, New York. The below grade facility will provide a storage of untreated stormwater during highflow periods to be treated later, thus reducing CSO discharges to Onondaga Creek.The CSO system consists of three parallel storage tunnels and two end chambers (west and east chambers) as main underground structure. The storage tunnels are about 850 ft. long, 55 ft. wide, 24 ft tall and located 20 ft deep below grade. The chambers, include above access and operation structure, are about 40 to 55 ft. deep and approximately 60 to 100 ft. wide.Kiewit Infrastructure and Weidlinger Associates Inc. developed an alternative approach for the tunnels to meet the facility completion schedule, strict design guide lines and quality control as an environmental and water tight concrete structure for the project. The original design anticipated use of a TBM machine to bore three parallel tunnels between two previously constructed chambers.The alternative design used a three barrel culvert cast-in-place structure in a cut and cover excavation supported by a soil bentonite wall. The SOE along the jet grouted bottom seal provided a ground water cut off as well.The SOE system is specially designed to enhance the quality of culvert CIP structure construction by providing enough space for a full height construction. Also it further reduces the construction time by having the less squarefootage of jet grout installation. The design of tunnel systems is accomplished effectively through the utilization of soil structure interaction using a finite element methodIntroductionTo avoid construction of an additional treatment plant to handle increases in combined sewage flows, the Department of Water Environment Protection of Onondaga opted to construct the Clinton combined sewer overflow storage (CSO) facility.The Clinton CSO facility provides an environmental friendly mitigation method for combined sewer overflows on Onondaga lake which is located in northwest of Syracuse."

Jan 1, 2015

By W. L. Chong, Y. Zou

There are many types of Earth Retention Systems (ERS) available in the market where more than one method can be a feasible solution for a project. This paper examines the design and construct process of a project in Dee Why, NSW using a hybrid ERS comprising contiguous piles with jet grout infill. The development comprises a deep basement and mixed-use urban superstructure. The site is located in an area of variable ground conditions, high ground water table and in proximity to existing buildings with multi-level basements. This paper details a comprehensive assessment of the geological conditions and strategies adopted to better understand the effectiveness of the proposed product and to minimise the associated risks of the proposed solution. This involved conducting additional geotechnical investigation, extensive numerical modelling and in-situ monitoring of the movements and the performance of the walls. A monitoring regime consisting of inclinometers, survey points on capping beam and prisms on the neighbouring buildings and roads surrounding shoring wall was implemented. The monitoring results were back-analysed using computer software WALLAP, Plaxis–2D and Plaxis–3D for the post-construction examinations. This paper details the effectiveness and advantages of a hybrid ERS using contiguous piles with jet grout infill.

Nov 1, 2022

By Ezra Ballinger, Matthew R. Glisson

Located in downtown Fargo, North Dakota, the Block 9 Redevelopment project site contains highly- compressible soils in the upper 100 feet with groundwater about 10 to 15 feet below the existing ground surface. The owner prohibited using driven piles to avoid disturbing neighbors of the project and historically, drilled shafts are used in Fargo as a reduced noise and vibration alternative to driven piles. However, developments over the last 20 to 30 years in drilling equipment, load testing and integrity testing resulted in the project team identifying augered cast-in-place piles as a suitable alternative for this project. To reduce the risks associated with using a relatively unproven foundation system in the area, the project team used the design-build delivery method for foundation design and construction. The team also specified compression load testing and higher-than-normal integrity testing. A successful bi-directional load test validated the design parameters for the augered cast-in-place pile while thermal integrity profiling gave the team confidence that these piles would perform similarly to the test pile. PROJECT DESCRIPTION The Block 9 Redevelopment project goal was to turn an existing, at-grade parking lot in downtown Fargo, North Dakota into a public outdoor plaza, a mixed-use building and a parking ramp. The project provides new offices, retail spaces, a hotel, a restaurant and private apartments. Situated in the southeast quadrant at the intersection of Broadway and 3rd Avenue North, the project site wraps around a bank building that was to remain. According to aerial photographs, the eastern portion of the site contained a public parking ramp that was constructed between 1952 and 1976, and subsequently demolished between 2009 and 2010. The western portion of the site had some combination of buildings and surface parking visible in aerial photographs taken between 1952 and 1979. Since 1984, aerial photographs show the western portion of the site being entirely surface parking. The redevelopment included the construction of three structures: the Tower, the Podium and the Parking Ramp, as shown in Fig. 1. With plan dimensions of roughly 100 feet by 100 feet, the Tower has 1 level of below-grade parking and 19 above-grade levels rising to a height of about 230 feet above grade. The Tower contains eight levels of commercial office space, four levels of hotel, six levels of residences and a mechanical level. This configuration resulted in column service loads ranging between 435 and 2,685 kips. The Tower core area has a total service load of about 30,000 kips.

Jan 1, 2019

By Tony P. Suckling

This paper describes an investigation into the bleeding behaviour of bentonite slurry observed on a trial diaphragm wall panel. The bleeding is thought to be due to the bentonite experiencing a chemical reaction leading to settlement of the solids within the fluid, possibly as a self-weight consolidation process. The trial panel was constructed in a busy airport environment where many different chemical products are used for de-icing the aeroplanes, runways, apron areas, vehicle access and pedestrian routes. The relationships between slurry contamination, bleeding, bentonite hydration time and filter loss behaviour were examined as no relevant published literature could be found. The results show that the amount of bleed strongly depends on both the degree of contamination and the hydration time. It is concluded that bentonite fluids should be allowed to sit in the storage tank for at least 24 hours after mixing, and that the filter loss test is a quick and effective method to determine the potential for bleeding of contaminated slurries.

Jan 1, 2011

By Hubert Law, Dan A. Brown, Kyle M. Rollins

"Soil mixing and jet grouting provide a means to significantly increase the lateral resistance of pile group foundations with relatively little investment of time, effort, and expense compared to the cost for additional piles necessary to produce the same increased resistance. Comparative field testing conducted on full-scale pile groups before and after treatment of small soil volumes showed significant improvement in lateral resistance. The lateral resistance of the pile group increased by 60% due to soil mixing and by 180% due to jet grouting. To provide additional understanding regarding the influence of the soil mix strength, depth of improvement and width of improvement, a series of parametric studies were performed using a 3D finite element model. This set of “virtual load tests” was then combined with the results from the actual field tests to help develop a simplified model to account for observed behavior. In general, the testing and analysis indicate the pile group and the surrounding improved soil block generally act as an equivalent “super pile”. The passive force, side shear and base shear on the improved soil surrounding the pile group itself increased lateral resistance. This increase in resistance from the soil block can be added to the lateral resistance of the pile group.INTRODUCTIONThe lateral resistance of pile groups is often critical to the design of bridges and high-rise structures subject to seismic, wind, wave and landslide forces. Typically, when analyses indicate that the lateral resistance of a foundation is inadequate, additional piles, drilled shafts or micro-piles are added to increase the lateral resistance. Furthermore, an expanded pile cap or connecting beam is often required to structurally connect the new piles to the existing pile group. While this approach provides the required lateral resistance, it may also be relatively expensive and time consuming. An alternative approach is to use soil improvement techniques to increase the strength and stiffness of the surrounding soil and thereby increase the lateral resistance of the pile group. The improved zone could potentially be relatively shallow because the lateral resistance of piles is typically transferred within 5 to 10 pile diameters. For example, the soil around the periphery of the foundation could be relatively easily improved for an existing foundation as illustrated in Fig. 1(a) using a variety of soil improvement techniques. Alternatively, the soil under the foundation could be improved for a new foundation or even for an existing foundation with a technique such as jet grouting (see Fig. 1(b)). Improving the soil under the foundation would have the potential for producing greater increases in lateral resistance because the improvement would reach interior piles. In addition, the process of creating a cemented “soilcrete” zone around pile foundations could potentially produce a zone which would behave like a reinforced “superpile” with increased structural stiffness."

Jan 1, 2015

By Kyle R. Lackner, Jared P. Williams

"The Sutter Butte Flood Control Agency initiated the Feather River West Levee (FRWL) Program in 2010 to bring 35 miles of levee along the Feather River into compliance with applicable Federal and State standards for levees protecting urban areas. A combination of soil-bentonite cutoff walls, soil-cement-bentonite cutoff walls, and seepage berms will reduce flood risk by correcting under and through seepage deficiencies and remove more than 34,000 properties from the FEMA Special Flood Hazard Areas. The FRWL program includes a combined total of 7,744,803 square feet (SF) of cutoff wall planned to be constructed between 2013 and 2015. Cutoff wall construction methods to meet the design depths included conventional excavation to a depth of 85 feet and deep soil mixing for depths up to 120 feet. A key component of the FRWL program was the development of site specific mix designs using the design boring logs to evaluate the expected backfill gradation and permeability results. Issues that required a partnership between Contractors, Owner and Engineers included substantial Archaeological and Cultural Resource delays, significant depth changes due to a change in competent key, right of way acquisitions for abutting land, and the magnitude of the project in a resource limited industry.IntroductionThe Feather River watershed basin is located 50 miles north of Sacramento, CA and incorporates the agriculture producing communities of Yuba City, Live Oak, Gridley and Biggs. These communities are protected from flooding by levees that contain under-seepage and through-seepage deficiencies and were the cause of major failures in 1955, 1986 and 1997. The Feather River West Levee (FRWL) program was initiated by the Sutter Butte Flood Control Agency (SBFCA) in 2010. The long term objective of SBFCA is to correct the levee deficiencies and provide 200 year flood protection to more than 34,000 at risk properties located within the FEMA Special Flood Hazard Areas.Although FRWL contained a variety of construction components such as earthwork and pipe replacement, the slurry cutoff wall is the primary construction element for addressing under and through seepage deficiencies. From 2013 to 2015 approximately 6,649,210 SF of cutoff wall were installed using conventional excavation and deep soil mixing (DSM) techniques leaving 1,095,593 SF to be completed in 2016. The work was designed, solicited and constructed under two separate contracts, titled Project Area C and Project Area B&D. A summary of the contracts and cutoff wall quantities is presented in Table 1."

Jan 1, 2016

By Fei-chiu Huang

A 17-acre landslide occurred in February 2001, on a slope below Via Bellota in the City of San Clemente, California. Three homes were destroyed and many others placed in jeopardy. The landslide, involving portions of five separate developments, continued to move significantly in the years following. Litigation ensued among the affected parties, and investigations continued through 2007. A mediated repair resolution was ultimately reached among the parties. The agreed upon repair consists of a multi-million dollar stabilization program that included grading, drainage, and structural systems. Part of the construction cost was offset by creating 4 new ocean view custom lots and 20 new mobile home lots. The landslide repair and slope stabilization design involved removal and replacement of portions of the landslide debris and construction of buttress and stabilization fills as well as installation of 74 shear pins in two rows. The shear pins were designed as 4-foot diameter by 50 feet in length and incorporated continuous W30x211 wide flange steel. The shear pins were designed to be installed 25 feet above the slide plane and 25 feet below the slide plane at each location. Construction of the 74 shear pins was initiated in 2008 and completed in 2009. Four-foot diameter holes were drilled by utilizing a truck-mounted, flight-auger-style drilling rig with a 4-foot diameter solid-flight auger. Prior to the installation of the shear pins, an engineering geologist downhole logged strategically selected holes to further evaluate the actual slide plane elevations. The wide flange steel shear pins were then lowered to the desired elevations and encased within 4,500 psi, Type V, 0.45 maximum water/cement ratio concrete. Inclinometers installed within four pin shafts and behind the pin rows indicated performance in accordance with the design. Slight to non-perceivable shear displacement was measured which mobilized the intended capacity at the monitored shear pins. No excessive slope movement was detected at any of the inclinometer locations during or after the construction period. Actual shear displacement of the steel wide flange elements was less than the movement anticipated before shear pin installation.

Jan 1, 2010

By Arash Khosravifar Ph. D. P. E., Thomas Torkelson P. E., Milad Souri Ph. D. P. E.

Kinematic demands from lateral ground deformations can be a major cause of damage to maritime and highway transportation structures such as wharves, piers, and bridges. These kinematic demands are different from the ground deformations in the free field in that the resisting forces from piles will reduce the ground deformations to some extent (i.e., pile pinning effect). Current design codes for wharf structures allow the beneficial resisting forces from pile pinning effects to be incorporated in pseudostatic slope stability analysis (e.g., ASCE/COPRI 61-14). While design guidelines that are specifically developed for bridge foundations provide recommendations on how to incorporate the pile pinning effects (e.g., Caltrans 2012), their applicability to wharf structures need to be evaluated. This study uses the results of a large-scale centrifuge test on a pile-supported wharf structure to evaluate the accuracy of available Newmark sliding block analysis in estimating the lateral ground deformations. Pile pinning effects are incorporated based on the approach outlined by Caltrans. The results of this study support the use of existing pile pinning methods that were primarily developed for bridge foundations in maritime structures (e.g., wharves and piers). It was found that median Newmark displacements provide a good estimate of the permanent end-of-shaking displacements and that the median plus 1 standard deviation Newmark displacements provide a good estimate of the peak transient displacements. Design considerations for use in the Newmark sliding block analysis to estimate the kinematic demands on piles are discussed.

Oct 1, 2022

By David Chadwick, Paul Marsden, Chris Hughes, Mathias Delapille

"Following damage caused by the 2011 Christchurch earthquakes, the NZ$127.5million Christchurch Town Hall Restoration project is due for completion in 2018. The building is undergoing extensive repairs and a strengthening regime to meet New Zealand’s New Building Standard. One major aspect of the project is the stabilisation of the soil directly beneath the building using interconnected jetgrouting columns installed a cellular configuration, the purpose of this being to decrease the likelihood and severity of foundation movements caused by earthquake-induced soil liquefaction and lateral spreading. The soils encountered on the site ranged from cobbles and gravels through to sandy silts with a significant quantity of timber and rootlets. This wide variation of soil types presented a number of challenges with regard to effective and consistent treatment by jet grouting. The paper presents an overview of the quality assurance practices and also the testing regime adopted on this project.INTRODUCTIONMost of the deformation experienced by the Christchurch Town Hall structure over the course of the Canterbury earthquakes was caused by movement of the underlying ground. Two primary mechanisms of ground deformation were observed:- Liquefaction of the soils underlying the building foundation- Lateral spread of surface soils towards the free face at the river edge which runs 20 metres from the building. This mechanism also resulted in additional vertical settlement of the building foundations.The overall foundation design philosophy adopted by the project team for the Christchurch Town Hall Conservation Project has been to improve the ground directly beneath the structure to mitigate against these two mechanisms of ground movement. Additionally, a robust raft slab is proposed to distribute the foundation loading more evenly and increase the ability of the structure to resist lateral stretch of the underlying ground.The ground improvement system proposed by the Client’s geotechnical consultants, Tonkin &Taylor, comprised a cellular arrangement of interlocking jet grout columns, this arrangement would effectively encapsulate the soil within the cells preventing lateral spread.In total 1,097 interlocking jet grout columns, extending over the entire floor plan of the structure, were required to satisfy the design requirements."

Jan 1, 1900

By Carlandrea Albonico, Salvatore Miranda

After a brief introduction of the whole Project, the paper describes two special geotechnical engineering solutions provided within the scope of the Galataport Project, in Istanbul, Turkey. The first refers to the new quay of Salıpazarı, which is a combination of retaining structure and ground improvement, formed by a combiwall, a reinforced concrete diaphragm wall and a soil improvement by deep soil mixing (Turbojet). The second, refers to the soil improvement works executed underneath three existing buildings. Single-fluid jet grouting columns had the scope of improving the mechanical properties of the bearing soil and reducing the associated risk of liquefaction. A set of underpinning micropiles was installed in order to allow the excavation of a partial basement inside two of these three buildings. All activities were conducted from inside the existing buildings, with reduced headroom. The paper highlights the importance of employing cutting-edge technologies within the foundation engineering field and state-of-the-art electronic control devices, in parallel with the essential human expertise, in order to obtain the desired results in this high-profile Project.

Nov 1, 2022

By Stuart Coutts

"This paper presents an overview of the author’s experience related to the assessment of the base capacity of straight shafted and enlarged-base bored piles in sand. A design approach based on CPT qc is described which has been calibrated using a database of load tests. The importance of correct installation techniques with instrumentation are illustrated and a discussion is presented on the current use of high strain dynamic testing to validate compliance with design. An example of a recent project with high quality instrumented load test data illustrates the close match to the proposed best practice approach and also highlights the importance for consideration of the effects of stress relief for deep foundations installed in deep excavations.1 INTRODUCTIONContinuous Flight Auger (CFA) piles are the bored foundation pile of choice for sand deposits across Australia. The evolution of the determination of the base resistance of CFA piles has been shaped by available investigative techniques, calculation methods, and calibration of designs with laboratory and field testing. The Cone Penetration Test (CPT) has been widely used in Western Australia (WA) where the test has been commercially available via multiple contractors for more than 25 years. On the East coast, the adoption of CPT testing has been slower with a transition from traditional Standard Penetration Testing (SPT) still occurring. Dynamic pile load tests are often used to derive parameters. The influence of pile installation on performance is commonly misunderstood and is an important element on any discussion of pile capacity for CFA pile types. The interface between the base of the constructed pile and the in-situ soil has an influence on capacity such that a poorly constructed pile base will have limited (if any) contribution to pile performance within the normal working range, generally within a 10 mm movement. The research presented in this paper pertains to CFA piles (no drilling fluids) and enlarged base piles constructed using CFA techniques under drilling fluids such that clean pile/base interface is targeted. Developments in modern piling equipment and instrumentation allow the pressure and volume of delivered concrete/grout to piles to be accurately monitored at various stages of installation such that repeatable ‘best practice’ can be achieved. The changes in soil conditions that occur due to the disturbance of the install technique are also important.Although the results of this research are likely applicable to bored piles, the interface between the pile and in-situ soil (shaft and base) need to be considered for various installation techniques. The effects of stress relaxation (due to removal of soil above pile base and adjacent shaft), time to concreting, and the zone of disturbed soil around the pile shaft are paramount.2 INSTALLATION CONSIDERATIONS The pile mix (concrete/grout) and interface with the in-situ soil are also an important consideration. For example, coarse grained, poorly graded, dry, clean sand will be partially permeated by most pile mixes; such that the influenced soil will be enhanced and in instances the overall effective pile dimensions increased. Permeation of the disturbed zone of a pile or anchor shaft along with scale effects (Lehane 2009) can have significant effect on shaft capacity and shaft frictions significantly exceeding expected are not uncommon based on ‘theoretical’ dimensions. Advancements in mix technology and mix techniques also have a large influence on the pile/soil interface. The ability of the piling rig and augers to excavate a plumb and gauge hole can also have a large influence on the zone of soil disturbed adjacent the constructed pile with a resulting influence on capacity."

Jan 1, 1900

By M. Melih Demirkan, Jared Deible, Michael Rosenmeier, Mazen Elias Adib, Juan J. Gutierrez, Raghav Ramanathan

Dewatering and groundwater control is required frequently for construction projects and needs to be accounted for and dealt with care during design and construction to complete the project successfully. Dewatering can cause changes in porewater pressure, which changes the effective vertical stress in a soil mass. Dewatering can also cause changes in groundwater chemistry which in turn can cause changes in porewater pressure and also dissolution of soluble minerals in the soil and rock. The Guideline developed in this study addresses the engineering issues, approaches to lessen the potential risks associated with construction dewatering, and presents dewatering practices to support dewatering applications regulated by the Municipality of Abu Dhabi City (ADM) in the United Arab Emirates (UAE). The subsurface condition within the city presents significant geotechnical problems due to presence of shallow subsurface cavities and soluble minerals in the soil and rock. Therefore it is critical to develop standards for dewatering practices to provide information for local dewatering engineers and contractors with special emphasis to control and to eliminate the subsidence/collapse problems related to dewatering projects within the Abu Dhabi city. The ADM is also responsible for approval of permit applications for projects that involve dewatering. In order to minimize the risk related to subsidence/collapse problems due to dewatering, construction companies and dewatering contractors need to be informed about possible mitigative measures that can be employed to reduce risks. The guidelines were developed as part of this study based on detailed analysis of the local subsurface conditions. A set of rules and regulations are developed for geotechnical and hydrogeological investigations, dewatering design and monitoring criteria depending on the hazard zones, proximity of excavation to critical structures, excavation depth. The Guidelines include examples of permit application packages for three types of dewatering projects; one involving shallow dewatering, one involving intermediate depth dewatering, and one involving deep dewatering. These Guidelines are considered as living document and will be updated as required, as additional information is collected and additional local experience is gained.

Jan 1, 2016

By Martin D. Larisch

The construction of diaphragm walls and most large-diameter bored piles (piers) is often carried out under drilling support fluids to temporarily stabilise the excavation prior to concrete placement. In most cases such fluids are either mineral-based slurries (bentonite) or polymer support fluids. The working mechanisms of these two fluid types are fundamentally different. Designers need to consider possible fluid-related impacts on the permanent design performance of the project-specific deep foundations as well as for the temporary excavation stage during construction. Robust design methods for bentonite slurry-supported excavations have been developed in the last few decades and the working principles and associated risks of such mineral-based slurries are understood reasonably well. However, such meth-ods have not been developed in detail for polymer-based drilling fluids. This document provides a brief overview of the main characteristics of bentonite- and polymer-based drilling fluids as a guide for construction practitioners and design engineers alike. The paper also high-lights some common construction risks related to casing installation and the selection of suitable fluid systems for different ground conditions. Typical defects caused by the incorrect application of drilling support fluids, and their pro-active mitigation, are discussed, too. In addition, the basic concepts of sta-bility calculations for bentonite fluid-supported deep excavations are briefly introduced and their ap-plicability for other fluid types such as polymer-based support fluids or water are reviewed.

Nov 1, 2022

By Waddah Akili

This paper describes the steps taken in planning, developing, and executing a case study/ case history course in geotechnical/ foundation engineering at an international university. The paper sheds light on: how a “workable” format for the course was arrived at; the organization of the course; and the results of evaluating the effectiveness of this approach versus traditional lecturing. Problems and challenges that could arise when offering the course for the first time are also addressed. Embedded in this experience and its related protocols are: the emphases on engineering design and the practice, teamwork and leadership development, organizational management, and oral and written communication skills. The paper concludes by confirming that discussions, through an open forum, are judged to be superior to traditional lectures in improving critical thinking, cultivating desirable personal attributes, and acquiring problem-solving skills.

By Amy B. Cerato, Shawn Allred, Tatiana Vargas

"Helical piles are deep foundation elements that resemble, and are installed like, a large steel soil screw — they have a slender steel shaft with one or more round helix bearing plates welded to the shaft to provide support to the structure they hold. Helical piles are rotated into the ground with a large torque motor and provide support through soil bearing on the helix bearing plates and along the shaft. The piles are available in many lengths and, due to their small footprint along with their ability to create minimal disturbance to surrounding structures, they are often used in urban settings for foundation repair, retrofitting existing buildings and for new construction projects. Helical piles are routinely installed as foundation elements in seismically active areas, such as New Zealand, Japan and the U.S.Anecdotal observations (e.g., from New Zealand, Japan and the U.S.) have shown that piles with a comparatively small cross-section and high anchoring capacity, such as helical piles, are beneficial for seismic resistance. This is presumably due to the pile’s slenderness, higher damping ratios, ductility and resistance to tipping uplift. In New Zealand, it was observed that helical pile foundations fared much better than driven and drilled concrete piles after the 2011 Christchurch earthquake. In a personal communication, Woods (2016) described that, out of the 300 structures in center city Christchurch that were supported by helical piles, fewer than 10 structures suffered significant structural damage. However, many structures supported by driven and drilled concrete piles were damaged to such an extent that they were condemned and subsequently demolished."

Jan 1, 2017

By Jim Slatter, Ben Collingwood

"It is well known that the adoption of an appropriate construction methodology is critical to quality outcomes for bored piles (drilled shafts). Many case studies have been published documenting quality issues that have arisen due to a range of causes involving ground conditions, ground support, drilling and cleaning techniques, groundwater, concrete properties and concreting methods, amongst other things. Despite the body of published information, pile defects remain common in practice. The authors share over 40 years’ experience in the Australian piling industry and have participated in many hundreds of projects involving bored piles in design, construction and testing roles. It is the authors’ experience that many defects are caused by conditions or practices that are known to be problematic, but that are often not recognised or addressed at the time of the works. This paper provides an overview of industry practices and key factors relevant to quality outcomes. The authors draw upon their own construction experience, published case studies and guidelines, and observations from independent pile testing activities they have been involved in across the Australian piling industry. The intent of the paper is to provide a consolidated review of typical industry practices and to highlight key areas in which construction quality can be enhanced.INTRODUCTIONThere are many published studies of cases where bored piles have been constructed and found to have concrete defects. The authors have had personal involvement in many cases where the outcomes and learnings are not publically available. The nature and cause of defects is always dependent on site and project specific factors, and therefore methodologies and materials that produce satisfactory outcomes in certain circumstances may be problematic elsewhere. The process of bored pile construction encompasses the following key areas:??excavation and ground support;??pile preparation and cleaning;??pile reinforcement and fitments.??concrete supply and mix performance;??concrete placement methodology;Each of these elements is equally important and can influence construction quality in completed piles. In the authors’ experience, it is often a combination of seemingly minor issues that leads to significant defects in piles. Conversely, attention to detail in all aspects of bored pile construction is required to produce outcomes of a consistently high standard."

Jan 1, 1900

By Manchanda H, Agarwal J.

The construction industry has one of the largest numbers of injuries compared to other industries. Thus, reducing accidents and determining construction risks are extremely important. One of the essential steps for construction safety management is hazard identification and risk assessment, since the most unmanageable risks are from unidentified hazards. While the urban rail transit systems are being developed rapidly in almost all major cities of India, adjoining Existing Building Structures and historic sites are facing possible threats of unexpected damages and accidents. The protection of these structures becomes one of the major challenges specifically when the infrastructure being developed involves construction of underground tunnels passing through old cities. The assessment of settlement induced damage on buildings during the preliminary phase of tunnel excavation projects, is nowadays receiving greater attention. Analyses at different levels of detail are performed on the surface building in proximity to the tunnel, to evaluate the risk of structural damage and the need of mitigation measures. The current paper presents current practices being adopted in India for prediction and excavation of tunnelling induced ground movement and building damage risk-assessment. The paper highlights empirical and numerical approaches towards predicting settlement induced damages on buildings during the tunnelling, detailed step by step methodologies for conducting building condition surveys, evaluating associated hazards, and adopting adequate building risk identification and mitigation methods. The paper also discusses associated technical and contractual challenges and highlights way forward to overcome them.

Sep 1, 2022

By P. J. Nicholson

The methods of reinforcement to be discussed in this paper are all insitu methods, ones that can be used on the soil structure as it exists in the ground, and do not rely on excavation and replacement of the soil. Current practice in the United States, as well as new ideas and methods, will be discussed as they relate to slope stability, retaining walls, and to other uses such as control of mine or cavity related subsidence and to liquefaction control under existing structures. The method is based on the concept of "nailing" or reinforcing the soil in place, and thereby causing a mass of soil to act as a coherent unit. When performed properly, a true gravity structure can be constructed, one that will remain intact under both horizontal and vertical loadings and that will also resist vibrational and seismic loadings.

Jan 1, 2010

By Frank Borda

Two recent projects were completed in Ontario, Canada for major hospital additions that involved excavation support of heritage masonry structures. Conventional continuous caisson wall schemes were replaced, with significant cost savings, by tied back shotcrete systems. Using a combination of conventional design and FLAC analysis, excavation support was designed to permit excavation in competent to weak soils that limited horizontal movements of the existing structures to between 3 and 8 mm. The use of vertical wall elements (micropiles) integral to the shotcrete wall to support both the vertical wall loads and the face of the excavation was deemed to significantly reduce lateral and vertical wall movements. FLAC analysis was used successfully to predict wall movements and optimize design. The shotcrete method proved to be flexible and adaptable to design changes during the project. This permitted convenient accommodation of changes to the building geometry after excavation support had commenced. In addition the method accommodated staged demolition and excavation support of portions of the existing structure at low cost, conveniently and without delays.

Jan 1, 2004

By James Warner

Investigations of the sinkhole indicated that the loose, disturbed ground was completely encircled by dense competent core. This confinement substantially increased the effectiveness of the compaction grouting compared to what might have been expected at a "greenfield" site. However, the 8 ft diameter circle shown in the plan view was only the surface expression of the sinkhole proper and the deep, loosened ground actually extended to a larger diameter of about 20 ft. The planned spacing of the grout holes was based on the finite element simulations using a target void ratio of less than 0.3 throughout the compacted ground within a 5 ft radius of the grout injection point. Because of the strong confinement effect, the layout of grout holes included one central primary hole surrounded by six secondary holes at a triangular spacing of about 5 ft. Since the disturbed ground was considered a confined cylinder, it was anticipated that the primary hole would perform the majority of work and the secondary holes would act as check holes, with progressively lesser grout takes as the loose ground densified.

Feb 10, 2003