Search Documents

By Håkan Schunnesson, Kirsten Holme

"When mining high grade, narrow ore bodies, the mining method often implies a very detailed knowledge of the ore contacts to avoid unacceptable ore loss and waste rock dilution. During the past decade, the use of microprocessor based drill monitoring equipment has become an accepted technique, even for percussive drilling. On the basis of the recorded drill performance, such as penetration rate, torque pressure, thrust etc., a fast evaluation of the lithological sequence of the ore zone can be made. In order to evaluate the potential of percussive drill monitoring to pro-vide detailed information of the geometry of the ore body, the technique was tested in the Viscaria copper mine in Sweden during 1996.To provide understandable information to the mine geologist, great emphasis was placed on the separation between the drilling response generated by variations in rock conditions from variations caused by the operator and the drill system. Due to the complicated geology in Viscaria, the drilling response presented to the geologists was separated in two independent signals, one representing the hardness of the rock and one representing the in homogeneity(fracturing) of the rock. With those signals a good separation between different rock types in the ore horizon was achieved.The experience from the Viscaria copper mine is that drill monitoring not only can be used to locate contacts between rock types, but also to characterize rock conditions and, often, also to specify the exact rock type present. Because it is possible to get the drill monitoring information very quickly it is a valuable complement to diamond drilling for increasing the specific knowledge of the geology and the ore body."

Jan 1, 1997

By Jan E. Nesset, James A. Finch, Wei Zhang

"Bubbles are unquestionably the heart of the flotation process. Their size and combined surface area are largely what drive the recovery process. This suggests that plant engineers should be aware of where their plants are operating with respect to what is achievable for these key parameters. The paper presents a model of how the key operating variables of frother type and concentration, gas rate, altitude (above sea level) and viscosity affect the Sauter mean bubble size (D32) and bubble surface area flux (Sb). The results are compared to a set of plant measurements that demonstrate the benchmarking capability of the approach. A case study is used to link hydrodynamic change to improved metallurgical performance.INTRODUCTION At the beginning of the 20th Century the early practitioners of flotation were aware of the importance of understanding bubble behaviour (Rickard, 1916) but measurement of individual bubble and gas behaviour in the industrial environment was not possible due to a lack of adequate sensors. This situation was not rectified until three quarters of a century later with the advent of industrially-robust sensors developed, notably, at the University of Queensland’s Julius Kruttschnitt Mineral Research Centre (JKMRC) (Schwarz & Alexander, 2006) and McGill University (Gomez & Finch, 2002). What emerged was not the chaotic environment perhaps expected, but defined relationships between gas rate, gas holdup, bubble size and the total surface area of bubbles. These relationships could be defined by mathematical expressions and predicted from an understanding of the key process variables (Gorain, Franzidis & Manlapig, 1997; 1999) (Hernandez-Aguilar, Gomez & Finch, 2002) (Gomez, Cortes-Lopez & Finch, 2003) (Nesset, Gomez & Finch, 2007). The early JKMRC work focused on a large pilot cell (3 m3) installed in plant environments, while the McGill work was initiated on flotation columns (Finch & Dobby, 1990) (Xu, Finch & Uribe-Sales, 1991) and later adapted to industrial mechanical cells (Cooper, Scott, Dahlke, Finch & Gomez, 2004) (Dahlke, Gomez & Finch, 2005) (Nesset, Gomez, Finch, Hernandez-Aguilar & Difeo, 2005). Yianatos of Santa Maria University (Chile), a graduate of the McGill research team, carried the work to industrial settings in South and Central America (Yianatos, Bergh, Condori & Aguilera, 2001). The methods of gas dispersion measurement are now well accepted and most major research centres and flotation cell manufacturers have adopted the technology (Pyecha, Sim, Lacouture, Hope & Stradling, 2006) (Yañez et al., 2009) (Collins, Schwarz & Alexander, 2009)."

Jan 1, 2012

Many mines in Canada, the US and S. Africa are reaching the hoisting limit. Very little payload will be possible without compromising safety due the excessive weight. It has been suggested (DeLorme, 2000), that one of the most attractive concepts to enable deeper hoisting is to reduce the allowable factor of safety in the wire rope. Researchers at the Spokane Research Lab are developing new technology to improve hoisting safety and productivity by providing new monitoring and analytical tools. A Shaft Conveyance Monitoring System (SCMS) has been developed which determines hoist rope end load, true conveyance position and acceleration, and rope safety factor, as well as other hoist operating parameters. This information is transmitted to the hoist operator display 20 times per second. Recent field measurements on 45 mm(1 ¾ in.) diameter hoist rope indicate that dynamic forces during loading of a 9000 kg(10 ton) skip may exceed the safety factor of the rope. To improve on the current understanding of the mechanical behavior of hoist ropes, and to help interpret the results from field-testing of the SCMS, a new approach to computer modeling of stranded wire rope is also being developed. Particle Flow Code, PFC3D (Itasca 1995b) is used to simulate the structural behavior of wire rope and the interaction between individual strands when the rope is subjected to static and dynamic end loading. Details of the SCMS, field results from the measured rope loads, and the results of numerical modeling on the wire rope will be discussed.

May 1, 2002

By Etienne S. Bieler

Mr. Chairman, Ladies and Gentlemen, I come to you tonight distinctly as a physicist, not as a geologist or a mining man. My experience in applied geophysics has been short, and I do not doubt that many of you have a much larger acquaintance: with the subject than I have. A little over a year ago, the firm of Alderson, MacKay & Armstrong decided to investigate the possibility of developing a new method of electrical prospecting suitable to our northern Quebec and northern Ontario conditions, and asked me to take up the work. A preliminary survey of existing literature convinced me that the field of induction methods was most promising. I wish to give you some account of the work carried on last summer in the Rouyn district in this connection with the very able assistance of Mr. H. G. I. Watson. Geophysical methods of prospecting can be divided generally into four classes: magnetic, electrical, gravitational, and seismic. Each class depends on the existence of a definite property in which the valuable mineral to be discovered differs materially from the surrounding rocks. In the four classes, the property will be, respectively, magnetic permeability, electrical conductivity, density, and elasticity. By far the largest differences occur in the case of electrical conductivity, where it is not rare to find ratios of the order of several millions, or even billions, between ores, sulphide ores especially, and the surrounding rock. Hence the sensitiveness and delicacy of electrical methods. Of these four classes, only two, the electrical and the magnetic methods, have been put to extensive practical use in the discovery of metallic ores. The other two classes are important mainly in connection with oil detection.

Jan 1, 1928

By Aparup Chattopadhyay, Barun K. Gorain

"Porphyry copper deposits are the most important source of copper and also gold within the orogenic belts. These deposits are characterized by low grade copper ore (0.2% to 1% copper) and host precious metals like gold, silver and platinum. A characterization tool has been developed for complex porphyry type copper-gold deposits with an aim to quantify copper and precious metal deportment. This quantification is a challenging task due to low grades and also due to the presence of both visible and invisible precious metal content in different sulphide and non-sulphide phases. Studies were initiated on various complex ore deposits and also on samples representing various processing streams such as flotation and leach products. This paper presents the development of a systematic approach to diagnostic metallurgy using state-of-the-art optical and automated mineralogy, micro-probe, dynamic SIMS and TOF-SIMS analysis for quantification of invisible and visible precious metals content in various species. The relevance of this characterization to metallurgy will also be briefly discussed in this paper.INTRODUCTIONA novel characterization tool has been developed for double refractory gold ores and complex copper-gold ores using state-of-the-art technology for quantitative gold and copper deportment study. The characterization of these ores is a challenging task due to low copper and gold grades in ores, presence of both primary and secondary copper sulphide phases and variable proportion of visible and invisible gold in different sulphides phases (pyrite, chalcopyrite, chalcocite and bornite) and iron oxide phases (magnetite, hematite and goethite). A study was initiated on various ore deposits and also on samples representing various processing streams of pilot plant batches such as flotation concentrates and tailings. This paper attempts to discuss the deportment characterization methodology through presenting results from investigations on four samples from a flotation circuit viz, Feed, Final concentrate, Cleaner Scavenger Tail and Rougher Tail samples. These four samples represent the key streams for a typical copper-gold flotation flow sheet. The key objective of this investigation was to identify and quantify visible and invisible gold along with understanding the morphology and liberation of gold associated with various sulphides, Fe- Oxides and non-sulphide gangue species. In addition, the aim of this study was also to relate this mineralogical and gold deportment information to metallurgical performance."

Jan 1, 2013

By Masayuki Ishikawa

In a radio frequency and optoelectoronic device packaging, Gold-Tin (Au-20 wt% Sn eutectic) solder is used widely due to the excellent electrical and thermal conductivity, high strength, and negligible creep characteristic under repetitive thermal cycling. With the recent lead-free movement, Gold-Tin solder is recognized as an alternative material for high temperature Lead-Tin solder. Generally, Gold-Tin solder is supplied in the forms such as ribbons, pellets, and ring frames. However, these forms must be set-up accurately on the joint area to press chips in bonding, therefore, it is difficult for these forms to satisfy the recent requirements for the down sizing in the connection areas. On the other hand, Au-20 wt% Sn solder paste can be applied flexibly to various supplying methods, such as printing, dispensing system and pin transcript. These methods also make it possible to reduce the production cost. However, in the case of using the solder paste, the void issue is one of the most undesirable problems. The void causes the degradation of the characteristics such as the bond strength, electrical characteristic and thermal conductivity. We have been intensifying the development of the void free paste, and have achieved void reduction by optimizing the powder size, the flux composition and the reflow condition.

Oct 1, 2003

By Patrick R. Stephenson

The current version of the JORC Code was issued in 2004 and since that date the Australian Securities Exchange, in collaboration with JORC, has issued a number of companies? updates to provide guidance on various reporting issues. An interim review will be undertaken during 2010 to meld these updates with the current 2004 Code. This will be followed by a full review during 2010/11 covering all aspects of the Code and focusing particular attention on: ? clauses / guidelines relating to Exploration Results1, exploration targets and the reporting of historical estimates; ? issues relating to the Public Report2, including definition, the requirements for Competent Person sign-off, level of disclosure and mandatory requirements; ? guidance on techniques to quantify resource / reserve estimation uncertainty; ? the level of study required to convert Mineral Resources to Ore Reserves, and disclosure of prices and economic factors; ? expansion of the requirements for reporting of marketable material for bulk commodities; ? the use of language and tone that anticipates new and emerging technologies and techniques for the qualitative and quantitative measurements of data; and ? linkages to valuation and the valuation code (The VALMIN Code). Although the Canadian and Australian reporting regimes for public statements on Exploration Results, Mineral Resources and Mineral (Ore) Reserves are similar in intent and coverage, they differ in detail, sometimes substantially. Canadian requirements are generally more wide-ranging and prescriptive than Australian requirements, including in the need in many situations to publicly lodge a Technical Report, a requirement that does not exist in Australia. Australian-listed companies seeking to list in Canada, and Competent Persons seeking to act as Qualified Persons in Canada, need to ensure that they are fully conversant with Canadian regulations and how they differ from those in Australia.

May 1, 2010

By K. Bartholomew

The Functional Performance Equation for ball milling circuits provides plant staff with a new means to improve circuit performance. However, successful execution of a plant processing performance improvement project, with verifiable improvements, requires a significant number of accompanying steps beyond using this equation. In order to identify and articulate all these steps, a study was undertaken with the metallurgical staff from two milling operations and process application specialists from a grinding media manufacturing company. “Task analysis” of improving plant grinding performance was carried out. This analysis identified the required steps, and ultimately yielded a “Plant Grinding Circuit Processing Performance Management/ Improvement System.

Jan 1, 2015

By Jamie King

This paper describes the use of dynamic scheduling and discrete event control to provide coordinated control of multiple automated vehicles. In the past decade there have been significant advances in the field of robotics for underground mining. As this trend progresses toward a realization of a completely automated underground mine the need for a central control system, capable of providing coordination for multiple vehicles in a semistructured environment, becomes more evident. In the past year general research into multi-robot coordination has been applied to the underground mining scenario and demonstrated in a scaled model underground mine in a laboratory setting. This system shows significant potential to be adopted into a full-scale implementation for mine wide automation.

May 1, 2001

By Stephen A. Gasiorowski, Frank J. Hrach, James D. Bittner

Separation Technologies, LLC (ST) has developed a processing system based on triboelectric charging and electrostatic separation that provides the mineral processing industry a means to beneficiate fine materials with an entirely dry technology. The environmentally friendly process can eliminate wet processing and required drying of the final material. The process requires little if any pre-treatment of the material other than grinding and operates at high capacity - up to 40 tonnes per hour by a compact machine. Energy consumption is low, approximately 1 kWh/tonne of material processed. Since the only potential emission of the process is dust, permitting is typically relatively easy. In contrast to the other available electrostatic separation processes that are typically limited to particles greater than 75 µm in size, the ST belt separator is ideally suited for separation of very fine (<1 µm) to moderately coarse (500 µm) materials with very high throughputs. The triboelectric particle charging is effective for a wide range of materials and only requires particle-particle contact. The small gap, high electric field, counter-current flow, vigorous particle-particle agitation and self-cleaning action of the belt on the electrodes are the critical features of the ST separator. The high efficiency multi-stage separation through charging / recharging and internal recycle results in far superior separations and is effective on fine materials that cannot be separated at all by the conventional electrostatic techniques. Since 1995, this triboelectric process has been extensively used for the beneficiation of coal fly ash with eighteen separators in place and over 100 machine-years of operation at locations in North America and Europe. The technology has been also successfully applied to the beneficiation of a variety of minerals including calcium carbonates, talc, and potash.

Jan 1, 2012

By Carlos F. Perucca

"Potassium is one of the three basic plant nutrients along with nitrogen and phosphorus. There is no substitute for potassium compounds in agriculture; they are essential to maintain and expand food production.Potash is extracted from buried ancient evaporites by underground or solution mining. This accounts for most of the potassium produced. Another important source is brine from landlocked water bodies, such as the Dead Sea, Salar de Atacama or Great Salt Lake.About 95% of potash produced worldwide is used in agriculture. The rest is found in several other industrial uses, including glass manufacturing, soaps, plastics and pharmaceuticals.Currently, three producers: IMC, PCS and Agrium operate 8 conventional and two solution mines in Saskatchewan, five of which run froth flotation circuits, two heavy media-flotation, two run forced crystallization and one natural crystallization.Potash in SaskatchewanPotash was discovered in Saskatchewan in the early 1940’s while drilling for oil. The deposits lie diagonally across the southern plains of Saskatchewan sloping southerly from a 1,000m depth at Saskatoon to more than 1,600 m depth at Belle Plaine and up to 3,000 m in depth in North Dakota. The known deposits are massive, accounting for more than 40% of the world’s known reserves."

Jan 1, 2003

By Michael Godard, Peter Cleyle

"Suncor Energy’s Project Millennium increased oilsands production capacity by an additional 95,000 barrels per day to its present level of 225,000 barrels per day. This massive venture included an expanded Mine, new Extraction and Upgrading facilities, as well as, steam and utilities infrastructuresIn the Primary Extraction process, removal of the bitumen from the oil sand begins with slurry preparation and is followed by primary , secondary and tertiary separation processes. The final cleaning step of the bitumen froth is the Secondary Extraction process, that removes residual water, mineral and solids to produce a clean diluted bitumen suitable for Upgrader feedstock.This paper will review the flowsheet of the Millennium Primary Extraction facility, from its recent commissioning through the ramp up to design production rates. In addition, new technologies in the Primary Extraction flowsheet will be reviewed.INTRODUCTIONAs conventional supplies of oil and gas are depleted in Canada, the Athabasca oil sands industry of Alberta becomes an increasingly important source of energy. Today, high quality crude from Alberta’s oil sands accounts for roughly 30% of Canada’s daily petroleum production. According to government projections, over the next 7 years, oil sands production is expected to more then double, and by 2010 more than half of Canada’s crude oil is expected to come from the oil sands.Oil sands deposits consist of a layer of sand saturated with bitumen covered by a muskeg overburden and underlain by silt and clay. The oil sand is mined where the overburden is economical to remove, typically less than thirty meters thick. The Athabasca oil sand deposits around Fort McMurrray is ideal for mining. Bitumen can be described as a diverse collection of hydrocarbons, organosulfur, and nitrogen compounds."

Jan 1, 2004

By M. Neven, R. A. Steane, E. Lam

"The Key Lake uranium mill is located in Northern Saskatchewan. It treats a high grade, complex uranium and metal sulphide ore. The plant and process are in many respects unique, because commercial treatment of this type of uranium ore had never been done before. The process and engineering design was based on extensive laboratory test results. A pilot plant testing stage was omitted because of confidence in the test results and time constraints to bring the plant into production.The bench scale testwork on exploration drill core samples along with preparation of the feasibility study and environmental impact statement were carried out between 1976 and 1979. The contract for detailed engineering was awarded to Wright Engineers of Vancouver in late 1980 and in August of 1981 following a public inquiry, approval to proceed with construction was granted.Construction began immediately, and during the winter the foundations for many of the plant buildings were poured and by the beginning of the following winter the buildings had been erected and installation of equipment began. Despite a six month construction worker strike in 1982, the crushing plant started up in June of 1983 and ore processing commenced in October of that year, approximately 3 months behind the original schedule.This paper describes the mill design and compares the expected performance, with the operating experience. Emphasis is directed towards flowsheet and equipment changes made since start-up, operational difficulties encountered and further improvements envisaged. Auxiliary systems are only discussed where they directly affect mill operation."

Jan 1, 1986

By Steve Cole

"The economic and strategic importance of PGE bearing deposits is fuelling renewed exploration and development efforts in the precious metals mining sector.This paper presents a review of the various techniques used in the processing of PGE bearing ores, from primary benificiation to processing routes for the different flowsheets that have been developed amongst current producers. Recent innovations such as preconcentration of ore using gravity separation, recent trends in flotation circuit design and the development of hydrometallurgical routes for the direct treatment of flotation concentrates without the need for smelting will be discussed. Data from recent projects will be presented to illustrate common characteristics of PGE ores and concentrates.INTRODUCTIONThe six platinum-group elements (PGE): ruthenium, rhodium, palladium, osmium, iridium and platinum, together with gold and silver, are considered to be ""precious"" metals. The recent spike in platinum and palladium prices coupled with the projected increase in demand for the metals has fuelled a spate of exploration and new projects in the PGE sector. Historically primary producers of PGE metals have controlled the flow of information relating to the mining and processing of these ores into the public domain. Very little published information relating to individual operations and processes is available in comparison to the abundant literature relating to other metals.The purpose of this paper is to provide a general overview of the issues relating to the processing of PGE ores. Each topic discussed could easily be the topic of a paper or book and so in many cases only the surface of the topic will be scratched. An attempt has therefore been made to provide as many references as possible.This paper discusses the classification and location of PGE ores, the mineralogical factors that affect recovery of PGE's, methods currently used for recovering PGE's and process trends in PGE metallurgy."

Jan 1, 2002

By T. Bhambhani, D. R. Nagaraj

"Ultramafic Ni ores present significant challenges in processing in that both recoveries and grades are not satisfactory, due to the presence of Mg silicates in large amounts. Significant quantities of xanthates and CMCs are generally used for their recovery by flotation. Additionally, given that some of these ores are processed under acidic conditions, CS2 generation due to xanthate decomposition presents some safety hazards. Technology to replace xanthate has been developed for which the safety and health issues are absent. Collector S-10294 shows significant improvements in Ni and overall S recovery at a dosing rate of one half that of xanthate. New polymeric modifiers have also been developed that help reduce the Mg content of the concentrates at very low dosages. The reagents are custom designed for use in normal or hypersaline water, and acid or alkaline conditions.INTRODUCTION The use of xanthates in sulfide mineral flotation is reported to have started as early as 1925 (Nagaraj 2005). The reagent is now ubiquitous in the mining industry, accounting for 40-50% of total collector consumption. In recent years, the development of more selective reagents has rendered xanthates largely obsolete in Cu flotation. However, xanthates continue to be sold in large amounts in the Au, PGM and Ni flotation industry, where bulk sulfide flotation is required. The low cost and easy availability is the largest driver for the use of xanthates in the minerals industry. Of particular interest to this study is the use of xanthates in the flotation of Ni sulfide ores. About 60% of the world’s annual nickel output is obtained from sulfide Ni ores (Hoatson, 2006). A strategically important category of these ores is the ultramafic hosted sulfides, such as those of Western Australia and Canada. These ores are characterized by low Ni grades (<1%), with the Ni minerals being pentlandite, violarite, millerite and mackinawite, and gangue minerals comprising an array of altered Mg silicates, mostly serpentines. The challenges associated with treating these ores are well documented (Eltham et al. 1973; Claridge et al. 1975). One challenge is that Ni recoveries from these ores are lower. This has been attributed to the increased pulp viscosity, as discussed in detail by Vasudevan et al., 2010. Additionally, Mg silicates tend to report to the concentrate in large quantities, which is problematic for two reasons: a) concentrate dilution, and b) the high melting point of Mg silicates tends accelerate wear on the refractory lining of smelters. This has been attributed to network transport to the froth phase via bubble flux and entrainment (Patra et al, 2010)."

Jan 1, 2012

By Martin Murenbeeld

Outlook: Nine Bullish Arguments 1. Global fiscal and monetary reflation: PIIGS, US, etc. 2. Global imbalances: the dollar must decline 3. Global FX reserves are ?excessive?: diversification 4. Central bank attitudes to gold: now positive 5. Gold is not in a bubble: room to rise 6. Mine supply is flat: ?peak? gold? 7. Investment demand: long-run uptrend 8. Commodity price cycle: many years to run 9. Geopolitical environment: positive

May 1, 2010

By Tony Robles

"A new process is disclosed for the recovery of gold and/or silver values from activated carbon wherein they are adsorbed as cyanide complexes. A unique chemistry allows the new process to use mill process water containing an inexpensive, non-hazardous compound as the eluant. The new process has an elution period of 5 hours at 98°C. The gold in the eluant can be recovered by electrowinning or zinc precipitation. The new elution process is simple, reliable, and provides an eluted carbon that may not require thermal regeneration before reuse. Retrofitting the new process to existing processes such as Zadra, Anglo, and others will not require significant capital expenditures.IntroductionThe efficient and reliable elution process for gold/silver from activated carbon is a very important process in the gold mining industry. The most common techniques for elution of gold cyanide from activated carbon are the Zadra and Anglo procedures.Specialized elution techniques like the Micron and Acetonitrile processes have not been commercialized to significant extent probably due to relatively complex unit operations and expensive reagents.Important functions of the gold recovery circuit are:Efficiently recover gold/silver from the loaded carbon.Carbon is in good condition for reuse for optimum recovery.The pregnant solution is amenable to electrowinning or zinc precipitation to recover gold/silver from the solution.The whole process to be simple and short to reduce gold inventories.Present Elution ProcessesTable 1 shows some carbon elution processes that are available today. The two main elution processes used in the industry are: (1) the Zadra process, in which hot cyanide solution is circulated through an elution column and electrowinning cells; and (2) the Anglo American Research Laboratory (Anglo) process, consisting of a pretreatment step with caustic cyanide solution, followed by elution with deionized water."

Jan 1, 2000

By S. Junnikkala, K. Föhr

"Experiments were performed with plant feeds with a continuous 1,8 m3 cell at Pyhasalmi mine with Cu flotation feed in order to test the applicability of the bubble surface area flux as an indicator of the flotation rate constant. It was found that bubble surface area flux could not predict the rate constants of coarse Cu containing fractions. In the middle size fraction, the correlation coefficient in the rate coefficient estimation was higher but not statistically significant. Only the fine fraction showed a linear relationship with a moderate correlation coefficient.The bubble surface area flux was shown not to be a function of the impeller velocity above a threshold value. The flux was an almost linear function of the superficial gas rate enabling to use the superficial gas rate instead of flux if the operation of an existing cell is to be estimated.INTRODUCTIONBubble area flux seems to offer a simple way of modeling flotation. It relates the flotation rate constant with the bubble surface area flux by a simple linear equation. Due to this, there has been a considerable interest in using the bubble area flux for flotation computations. It has even caused claims that a cell producing a high bubble surface area flux automatically produces a high rate constant and therefore a high recovery.This paper discusses some of the assumptions of the relationship and gives some plant results during two sampling campaigns.The bubble surface area flux s b is describing the area of bubbles available for flotation in a cell per unit area. The bubble surface area flux is related to the superficial gas rate J, by the Sauter mean diameter as follows"

Jan 1, 2001

By Ian Holl, Adam Hempstock, Rickardo Welyhorsky, Niel Morrison

"The Victor Diamond Mine is located in the James Bay lowlands, 90 km west of the First Nations village of Attawapiskat. The project was the first of its kind in northern Ontario and was completed approximately 9 months ahead of schedule.The Victor Mine process plant flowsheet was designed to produce a 95 - 98% by weight diamond concentrate. Main processing steps include 3 stages of comminution, dense medium separation and proprietary x-ray technology for final recovery. Reagent consumption for this process is limited to flocculant, for thickening of fine processed kimberlite, and FeSi for the dense medium separation.The commissioning phase of the Victor Project was executed over a period of 6 months and commenced prior to substantial completion of construction. The approach used was to focus on and complete commissioning of the higher risk dense medium separation and recovery systems prior to construction completion of up stream systems.INTRODUCTIONThe development of the Victor Diamond Mine took place over a period of approximately 5 years and had a capital cost of CAD997 million. It was a greenfields project in an undeveloped region of northern Ontario, only accessible by winter road. Figure 1, below, displays the location of the project within Ontario.The main stages of the project included feasibility, environmental permitting, engineering, construction, and commissioning. At the onset of the engineering phase, the mine was scheduled to enter production in October 2008. Through a team effort between AMEC and DeBeers Canada, the schedule was advanced by 6 months towards the goal of project completion in April 2008. Production status was attained in January 2008, approximately 9 months ahead of the original schedule. This paper focuses on the commissioning aspects of the project and includes a less detailed discussion of the engineering stage."

Jan 1, 2010

By Luke Keeney, Stephen Walters

"The start up of a new mining and metallurgical facility is a crucial step in the life of any mining project. The mining industries record is poor when evaluating processing plant operation relative to design capacity predictions made during feasibility studies. Multivariate geometallurgical orebody characterisation, using principle component analysis, is a method developed for improving predictive processing performance models during feasibility stages of mine development. This paper outlines the application of multivariate geometallurgical characterisation to the Cadia East deposit located in New South Wales, Australia. Cadia East is a low grade high tonnage copper-gold porphyry system in advanced stages of feasibility analysis. A dataset of ~32000 measurements and 150 comminution parameters (A*b and BMWI) has been used to develop class-based characterisation and modelling methodologies. The results of this study outline the development of class-based ore characterisation and provide a technique for analysing and interpreting large and complex geometallurgical datasets for prediction and optimisation of processing performance. The results enable sophisticated population modelling to be conducted which displays deposit scale processing variability, aiding circuit design specifications and predictions during feasibility studies.INTRODUCTIONA feasibility study is the major technical report on which the decision to proceed to production and on which financing is based (Shillabeer & Gypton, 2003). The mining industry’s record is not very good when actual construction time, costs, and operating performance are compared to the projections made in feasibility studies (Ballard, 1983; Gypton & Ward, 2000; Gypton 2002). A study by McNulty (1998) found that of 41 mineral processing and chemical plants built between 1965 and 1995, only 56% achieved design capacity within two years of commissioning and three were closed after failing to achieve design capacity within 36 months of start up (Shillabeer & Gypton, 2003). McNulty (1998) related this underachievement and failure of start up performance to the use of innovative process technology without appreciating and managing technical risk. Factors contributing to technical risk include inadequate pilot plant testing, scaled up prototype equipment without backup, design flaws and poorly understood complex process chemistry."

Jan 1, 2009