Search Documents

By Alfred Boyles

"Heredity"1 in cast iron has been a subject of much discussion. Numerous experimenters have found that the properties of gray iron may vary greatly without corresponding variations in composition or thermal treatment. The main structural difference in such cases is in the size and distribution of the graphite flakes and the explanations given usually attribute this difference to some chemical element not shown by ordinary analysis or to some physical factor, such as inclusions in the melt. It cannot be said that any of these theories is completely satisfactory. Much remains to be learned about cast iron and for this reason a study of the material was undertaken as a part of the program of fundamental research at Battelle Memorial Institute. A review of the literature indicated that very little systematic work had been done on the mechanism of freezing in cast iron. The experiments described below are largely concerned with that problem. Normal and "Dendritic" Cast Iron As examples of variation in type of structure, photomicrographs of two test bars of cast iron are shown (Figs. 1 and 2) and the composition and properties are given in Table 1. Both are common, unalloyed gray iron. Test bar No. 13 has normal graphite flakes while No. 49 has very fine, lacy graphite arranged in a dendritic pattern, the matrix in both being pearlite. These two types of cast iron are well known to foundry-men and need no detailed description.

Jan 1, 1937

At the meeting of the Board of Directors of the Institute on Jan. 26, 1917, the following actions were taken: Messrs. A. C. Clark, Lawrence Addicks and G. D. Van Arsdale were appointed Tellers to count ballots for Officers and Directors. Messrs. T. T. Read, V. S. Harper, and. E. J. Hall were appointed Tellers to count ballots on revised spelling. The Finance Committee's audit for the year 1916 was approved and ordered filed. The Report of the Finance Committee upon the method of raising this Institute's share of the deficit on the additions to the building was approved and accepted. Upon the recommendation of the Secretary, increases in the salaries of some of the employees were approved. The St. Louis Section received an appropriation of $200 for the year 1917. The Columbia Section received an appropriation of $150 for the year 1917. The Montana Section received an appropriation of $100 for the year 1917. The Colorado Section received an appropriation of $175 for the year 1917. The Utah Section received an appropriation of $125 for the year 1917. The Puget Sound Section received a set of Transactions in standard binding. The International Engineering Congress received a loan of $300 until the Congress can realize upon some of its assets.

Jan 3, 1917

By C. A. Heberlein

INTRODUCTION THE present war in Europe seems to have stimulated the demand for quicksilver. In July last, the price ranged around $35 per flask of 75 lb., while to-day it seems to fluctuate between $47.50 and $50. The use of quicksilver in the form of fulminate, containing 70 per cent., and as corrosive sublimate, containing 73.8 per cent., must be extensive and a further market advance may be expected. With such an advance, some revival in quicksilver mining maybe looked for, particularly in California, where many abandoned properties exist. What can be done with low-grade quicksilver ores under favorable conditions, particularly with low mining cost, may be seen from the following description of the Oceanic mine, near. San Luis Obispo, Cal. Its operations date back to 1876, when rich sand ores were discovered. In three years 7,400 flasks of quick-silver were produced, but since then the deposit has been only sporadically worked. Until two years ago various attempts had been made by the Oceanic Quicksilver Co. to mine the more refractory "mud rock," which was encountered lying beyond the "sand rock." Mud and sand rock in varying quantities were treated together with poor results, but operations were successful with sand rock of fair percentage. About two years ago,, when all the sand rock had been exhausted, Murray Innes purchased the Oceanic mine. He found large quantities of low-grade mud rock, varying from 6 to 8 lb. of quicksilver per ton, which at the prevailing low price of quick-silver demanded very cheap mining costs, in conjunction with high but cheap metallurgical extraction. At that time the extraction of quicksilver from mud rock ranged between 40 and 50 per cent., as far as I am able to, learn.

Jan 2, 1915

By McHenry Mosier

MeRcuRy is one of the strategic metals of which the supply has been raised from critical uncertainty to more than enough for essential demands. Work by the Bureau of Mines has contributed substantially to increased production of mercury in the United States and to consequent accumulation of Government stocks. Other contributing factors have been higher prices for mercury and Government loans to operators. The Bureau has undertaken 13 exploration projects, 10 of which have been completed. This work has comprised 28,376 ft. of several types of drilling and 23,798 lin. ft. of surface trenching, and has indicated commercial ore containing 34,800 flasks of mercury and marginal ore containing 26,200 flasks, a total of 61,000 flasks; equivalent, respectively, to domestic production for 8 months, 6 months, and 14 months. As Government stocks are now adequate, domestic production (currently at the rate of 50,000 flasks per year) is gradually being curtailed through Government control of labor and operating supplies. Introduction Mercury was one of the seven metals designated as strategic by the Army and Navy Munitions Board in 1939, when Congress appropriated funds for the investigation of domestic sources of supply of war minerals. The Bureau of Mines immediately started a limited search for strategic minerals, but the first mercury project was not begun until December 1940. The U. S. Geological Survey assisted in the search for cinnabar by contributing information on domestic mercury deposits, preparing maps, and making geological studies of exploration projects. The present high rate of production of mercury in the United States was encouraged by the increase in price to $196 per flask at New York (Fig. I) and Government loans to operators for mine development and plant construction. The Bureau of Mines has issued, for restricted distribution subject to wartime controls, 13 War Minerals Reports on individual mercury deposits (listed in appendix A). In March 1942 it also published a Progress Report of the Metallurgical Division, R. I. 3627, Cinnabar-reduction Plants of the Southwestern Arkansas Quicksilver District. Uses of Mercury Mercury and its compounds have more than 3000 uses. Its principal use is as a catalyst in the manufacture of gases for chemical warfare; the next largest is in pharmaceuticals. Mercury is essential also for: (I) certain electrical apparatus, (2) industrial control instruments at many war plants, (3) munitions, including blasting caps, (4) insecticides in agriculture, (5) antifouling paint for ship bottoms, (6) dental preparations, (7) general laboratory use, and (8) amalgamation of free-milling gold ores.

Jan 1, 1949

By McHenry Mosier

MeRcuRy is one of the strategic metals of which the supply has been raised from critical uncertainty to more than enough for essential demands. Work by the Bureau of Mines has contributed substantially to increased production of mercury in the United States and to consequent accumulation of Government stocks. Other contributing factors have been higher prices for mercury and Government loans to operators. The Bureau has undertaken 13 exploration projects, 10 of which have been completed. This work has comprised 28,376 ft. of several types of drilling and 23,798 lin. ft. of surface trenching, and has indicated commercial ore containing 34,800 flasks of mercury and marginal ore containing 26,200 flasks, a total of 61,000 flasks; equivalent, respectively, to domestic production for 8 months, 6 months, and 14 months. As Government stocks are now adequate, domestic production (currently at the rate of 50,000 flasks per year) is gradually being curtailed through Government control of labor and operating supplies. Introduction Mercury was one of the seven metals designated as strategic by the Army and Navy Munitions Board in 1939, when Congress appropriated funds for the investigation of domestic sources of supply of war minerals. The Bureau of Mines immediately started a limited search for strategic minerals, but the first mercury project was not begun until December 1940. The U. S. Geological Survey assisted in the search for cinnabar by contributing information on domestic mercury deposits, preparing maps, and making geological studies of exploration projects. The present high rate of production of mercury in the United States was encouraged by the increase in price to $196 per flask at New York (Fig. I) and Government loans to operators for mine development and plant construction. The Bureau of Mines has issued, for restricted distribution subject to wartime controls, 13 War Minerals Reports on individual mercury deposits (listed in appendix A). In March 1942 it also published a Progress Report of the Metallurgical Division, R. I. 3627, Cinnabar-reduction Plants of the Southwestern Arkansas Quicksilver District. Uses of Mercury Mercury and its compounds have more than 3000 uses. Its principal use is as a catalyst in the manufacture of gases for chemical warfare; the next largest is in pharmaceuticals. Mercury is essential also for: (I) certain electrical apparatus, (2) industrial control instruments at many war plants, (3) munitions, including blasting caps, (4) insecticides in agriculture, (5) antifouling paint for ship bottoms, (6) dental preparations, (7) general laboratory use, and (8) amalgamation of free-milling gold ores.

Jan 1, 1949

By J. R. Craig, T. N. Solberg, M. A. Linden

The central and southern Appalachian Mountains were the major sources of domestically produced gold throughout the first half of the 19th century and continue to yield gold today. Small amounts of gold were probably extracted by the Indians and the Spaniards but the first documented report of gold in the region was made by Thomas Jefferson who found, in the Rappahannock River of Virginia in 1782, a 1.8 kg (4 lb) lump of gold ore that yielded 26 g (0.85 oz). Gold was subsequently discovered in North Carolina between 1793 and 1799, in Virginia in 1806, in South Carolina in 1827, in Georgia in 1829, and in Alabama about 1830 (Becker, 1894-5; Pardee and Park, 1948). Production climbed to more than 933 kg/a (30,000 oz per year) between 1830 and 1852, but dropped sharply after the California gold rush in 1849 as experienced miners moved west in search of bigger and easier stakes. The Civil War briefly halted gold mining in the Appalachians, but production rose to an average of about 249 kg/a (8,000 oz per year) from 1865 until 1878 and to about 404 kg/a (13,000 oz per year) from 1881 until 1915 when it again fell to near nil (Pardee and Park, 1948). Minor resurgences occurred in the 1930s and 1940s. Although there has been no reported production in recent years, it is likely that "weekend panners" still remove hundreds of ounces from streams annually. The total reported production for the area through 1959 is more than 77 t (2.5 million oz). This paper reports some initial findings of a long-term project designed to investigate the mineralogy, chemistry, mode of occurrence, and petrology of gold occurrences in the Appalachians. The goal of the initial phase was to determine the compositional range of gold in the Appalachians as a step toward deciding if sufficient variations were present to allow the definition of "compositional signatures." The very few published data on gold fineness in the Appalachians are based on assays that commonly include gold and silver from several mineral species. Analyses in the present study were performed on individual grains of electrum using a spot size of 10 µm x 10 µm to 100 µm X 100 µm (394 X 394 micro in. to 3,940 X 3,940 micro in.), and thus reveal the true composition of the principal precious metal-bearing phase.

Jan 1, 1984

By Arthur V. Corry

GOLD was discovered in Alder Gulch, Virginia. City, Mont., on May 26, 1863. In a short time some 6000 people flocked to the new discovery, and on the banks of Alder Gulch six settlements sprang into existence, the principal one, Virginia City, alone surviving. This town today has a population of 800, and is the county seat of Madison County. It is estimated that between forty and fifty million dollars in gold was produced up to 1904. Virginia City is situated at the mouth of Alder Creek where that stream leaves the narrow canyon that cuts the steep foothills flanking Old Baldy Mountain, elevation 9572 ft., 12 mi. south. Virginia City itself is 5700 ft. above sea level.

Jan 1, 1936

By John E. Lanning

During the last decade, since most smelters have included Cottrell plants as standard equipment for the removal of dust from furnace gases, it has become apparent that smeltermen have had a new problem slowly developing. This problem has manifested itself in accelerated destruction of, or serious injury to, the masonry of flues and chimneys. The masonry either spalls, if the material is of low strength, or acquires large major cracks, either of which conditions attains such proportions that renewals or reinforcing become necessary to maintain the structure in satisfactory condition. This paper describes the failure of a large modern brick chimney to such an extent that its safety was vitally impaired; the investigation of its condition; the methods of restoring satisfactory strength to the structure; and the installation of an acidproof lining. Plant History The Clarkdale smelter of the United Verde Copper Co., which was put in operation in 1915, was primarily a blast-furnace plant. The smelter at Jerome had utilized blast furnaces exclusively, and in the design of the new (1915) plant, blast-furnace smelting evidently was considered of major importance, the smelting equipment consisting of four blast furnaces 48 in. by 26 ft. 8 in. and three reverberatories, each 19 by 101 ft. The latter, supplemented by roasters, were intended mainly for handling dust and fine ore resulting from the crushing operations. The original roasting equipment consisted of six six-hearth Wedge roasters, six more being added in 1917. All gases from blast furnaces, reverberatories, roasters and converters were conducted by means of suitable flues and dust chambers to one central chimney. This chimney, 30 ft. inside diameter by 400 ft. high, is a self-supporting steel structure, lined with 4-in. brick supported on steel shelf angles, riveted to the shell, spaced about 15 ft. vertically. The bricks were of local manufacture, not particularly hard-burned, and were laid in ordinary cement-fireclay-sand mortar. No record is available to indicate that any particular effort was made to secure an acidproof mortar. The same materials were employed in the construction of the reverberatory and roaster flues, and the roaster dust chamber. Parenthetically, it may

Jan 1, 1934

By H. DeWitt Smith, W. H. Sirdevan

The mine operated by the United Verde Copper Co. is situated near Jerome, Ariz., on the eastern flank of the Black Hills, at an elevation of approximately 5500 ft. (1676 m.) above sea level. The mine and the town of Jerome are located on a steep hillside, which slopes rapidly to the valley of the Verde River. The smelter town of Clarkdale is situated in the Verde valley 4.1 mi. (6.5 km.) distant in an air line from Jerome, and at an elevation of 3560 ft. The two towns are connected by the standard-gage railroad of the Verde Tunnel & Smelter R. R., a subsidiary of the United Verde Copper Co. This road is 11 mi. long and has a compensated 4 per cent. grade. At Clarkdale, it connects with the Verde Valley branch of the Santa Fe R. R. The narrow-gage (36-in.) line of the United Verde & Pacific Ry. was, until 1919, Jerome's only rail connection with a main trunk line. This road connects with a branch line of the Santa Fe system at Jerome Junction, after traversing 26 mi. of mountainous country. From the time of its location, in 1876, until its purchase by Senator W. A. Clark, of Montana, in 1889, the United Verde mine was worked on a small scale and shipments of high-grade gold-silver ore were made from the surface workings. Until 1894, when the narrow-gage railroad to Jerome Junction was completed, all supplies for the mine and smelter

Jan 1, 1922

By W. L. Remick

The hydrotator coal-cleaning process was developed as an economic necessity to meet the ever-increasing demand for an inexpensive method of cleaning coal down to the sizes ordinarily referred to as "dust." As the most urgent demand seemed to be in the anthracite field, all experimental work has been conducted in that territory during the past two years, with the exception of a few months during the strike of 1925-26, when some experiments were performed in the Alabama bituminous fields. The first commercial plant was constructed at the Middle Creek Colliery of the Philadelphia & Reading Coal & Iron Co.,. Pottsville, Pa. This plant is now operating. Application The field of application of the process is: 1. Cleaning anthracite fines, ordinarily described as "slush" or "silt." Slush contains all sizes from 3/32 in. down to and including I(dust." (Anthracite passing a 3/32-in. mesh is also referred to as No. 2 Barley and No. 4 Buckwheat.) 2. Cleaning sizes too fine for recovery by other methods. 3. Removal of coal from sand circulated in the Chance sand-flotation process. 4. Cleaning of bituminous sizes from % in. down to "dust." 5. As equipment for the performance of the froth flotation process. 6. Other separating, extraction and washing processes which may be considered outside the realm of coal cleaning. Principle of Operation Fig. 1 shows the method of classification practiced under the Hydrotator patent.' In coal cleaning the machines are operated as "hindered settling" classifiers, the flow of solids and liquids being so controlled that the units may be combined in series.

Jan 1, 1927

Jan 1, 1966

By Arthur Bell

(San Francisco Meeting, September, 1915) . PRIOR to 1908 the oil production in the State of California, had been almost entirely a heavy fuel, oil, with a high flash point, hut changed within a-short period to a large percentage of refining oil with a low flash, by reason of the coming in of the Santa Maria field, the Midway field, and the increased production of the Fullerton field. This is clearly shown in the following tabulation of California's production: Year Barrels . Below -20° Be, Above 20° Be,, Per Cent_ Per Cent. 1905 48,307,000 90 10 1910 77,698,000 SO 20 1912 90,075,000 6o 31 1914 10:3,600,000 47 53 The bringing in of these high percentage's of light oil with their dangerous low flash and the increasing demand for the refined products necessitated the devising of some cheap and efficient means of quickly separating the lighter elements either in the field or at the main distributing points; also it became necessary to remove the excessive percentage of water which many of the light oils carried in emulsion.

Jan 9, 1915

By Ronald C. Whiting

SINCE the advent of what has been aptly called "chemical flotation," about 1920, the number and complexity of the various chemicals used in practice have increased enormously. Over 300 patents have been issued dealing exclusively with flotation reagents, and many of these embrace from two or three up to a score or more of specific compounds. The exact number of compounds actually finding a practical use in flotation would be difficult to determine, though the U. S. Bureau of Mines gives an annual list by groups.

Jan 1, 1938

By B. DE MARE

THE No. 6 open-hearth furnace at the plant of the Worth Steel Co., Claymont, Del., is the first to be rebuilt according to the Kuehn system. This as well as the other five furnaces at Claymont, has a nominal capacity of 75 tons, but the actual charge is about 242,000 lb. No hot metal being available, the pig-iron is charged cold. Oil of low grade with an asphalt base is used as fuel. These two items have to be kept in mind when discussing the actual fuel consumption. Careful records have been kept covering a five weeks run and the following is a brief summary of them The time required to heat the furnace preparatory to charging from the time a wood fire was started until charging commenced was 36 hours. This, I understand, is much less than with furnaces of standard design. The draft of the furnace, as shown by a gage in the stack-flue, is 1.25 in. The maximum draft with new checkers on former runs was 1.50 in., this draft gradu¬ally decreasing as the checkers closed up. Both of the first helpers claim the present draft is all they need for the proper working of the furnace, and, as with the Kuehn regenerators the draft remains practically the same from beginning to end of a run, this is satisfactory.

Jan 1, 1929

THE following statement is contained in an article entitled "Mortgaging the Future." by Walter C. Teagle, president of the Standard Oil Co. of New Jer-sey, appearing in the current issue of the Lamp, the official organ of the Standard Oil Co.: "During the last eight months the domestic daily production. of crude oil has risen 300,000 bbl.. which means that no less a volume than 2,500,000 bbl. now are coming to market each day. . . . Every twenty-four hours 250,000 bbl. more than the consumer required are being added to our surplus oil storage. The temporary advantage of cheap petroleum products and the availability of fuel .oil, for a widespread use as a substitute for coal are not being weighed against the time when scarcity may follow on the heels of plenty and the public of tomor-row may have to pay for today's excesses. The over-production of crude and its consequences constitute a problem of national import which far outweighs the temporary advantages either to a part of the industry or to sections of the public.

Jan 8, 1927

By W. S. Morris

PETROLEUM'S importance in World War II can perhaps be better realized by the recitation of a few facts and figures: Gasoline needs in this war are already eighty times greater than in the last war. It takes nearly three pounds of gasoline to deliver one pound of bombs, filled with petroleum explosives, on an enemy objective. Every American soldier overseas requires an average of more than fifty gallons of petroleum products per week, with the oil used by Navy and supply ships and America's Allies boosting the consumption of oil per soldier to an even higher figure. Every oil well in the United States now must produce each day an average of four barrels of oil for war and combat jobs. More than fifty million gallons of gasoline, fuel oils, lubricants, and other petroleum products are now going directly to the fighting forces every day.

Jan 1, 1945

By K. D. Jacob

IN the decreasing order of the tonnages involved, the uses of phosphates can be grouped conveniently into three general classes, namely, fertilizer; chemicals for military, industrial, and technical purposes; and mineral feed for livestock. The quantity of phosphate used as fertilizer, principally in the form of superphosphate, has always exceeded by far that used for all other purposes, though in recent years a marked increase has occurred in its consumption for the other two general classes of uses. Prior to the present century large quantities of superphosphate, as well as a considerable portion of the production of phosphorus chemicals, score made from bone materials which were plentiful and cheap in some areas and which could be more easily processed than phosphate rock for the manufacture of chemicals. Today, however phosphate rock has almost completely displaced bone as a raw material for the manufacture of chemically processed phosphates in nearly all countries of the world.

Jan 1, 1944

Jan 1, 1970