Search Documents

By Pedro Augusto David Machado

The hot metal produced in small blast furnaces runs with a highly heterogeneous charcoal. The result is a significantly higher hot metal chemical composition variation, especially for the silicon content, which varies from 0.4 to 1.5% in Mini Blast Furnaces - MBFs, designed to feed an EAF and/or a BOF. These MBFs operate with frequent variation in their productivities to feed preferably only one of the steelmaking reactors, that is, EAF or BOF. The hot metal suitable amount, chemical composition and temperature, to be delivered at the steelmaking vessel, become the major concerns in the integrated operation MBF to EAF or BOF. In order to cope with those undesirable frequent variations, a solution has been proposed based on the existing technologies of oxygen jets and ladle refining techniques adapted to a hot metal ladle or to a Torpedo Car. The proposed technique is not only able to adjust hot metal temperature and chemical composition, but it also generates the adequate conditions for refinement from P and S, as well as “cleaning” hot metal ladles and Torpedo Cars by melting pig iron skulls. Therefore, this new technique development results in high hot metal yield, an adequate chemical composition and bigger campaign of hot metal ladle.

Aug 17, 2017

By Michael Brandner

HSM can be divided into different groups such as Conventional HSM with Roughing stands and HSM without Roughing stands = Mills with just finishing stands. The roll requirements for different stands are quite different. In Roughing stands the temperature of the slab is very high. Therefore the resistance against thermal wear/fatigue is the most dominating factor. Today mostly Chrome Steel, Semi HSS and HSS rolls are applied. A comparison and evaluation of such rolls will be described. In the finishing mill the tendency/wish is to use HSS rolls in all the stands. The grade HSS is defined by at least a certain amount of carbide forming elements such as V, W, Mo, Nb etc. The matrix and other precipitations can be adjusted according to the need and situation in the mill. In the pre-finishing stands the HSS is already well introduced. In the last finishing stands the original HSS tended to stick and the cobble rate increased. New development decreased the problem and gave some very promising results. In the last finishing stands beside the high performance a higher resistance against incidents is needed. Solutions in this direction including e.g. residual stresses and special core material will be discussed. Proper testing and grinding procedures can avoid losses and reduce the TCO. Data sourcing and evaluation in regards of rolling and grinding is the key for the optimization of the TCO. Several examples and comparison between different applications will be given in detail and explained. Future possibilities will be discussed as well as results of latest trials in mills.

Aug 17, 2017

By Yasser Ghobara

Phosphorus is a problematic impurity that has challenged steelmakers for decades. Steel producers have developed specific technologies to eliminate phosphorus prior to and during steelmaking. These process technologies reduce phosphorus to various degrees and increase the cost of making steel. The state-of-the art dephosphorization technologies are described and operating costs compared for each of the established technologies. Costs are discussed in terms of price penalties for high P iron ore and selling premiums for low P steel. From this, strategies to control P in a cost effective manner are described.

Aug 17, 2017

By Lucas Breder Teixeira

Esse trabalho discute a modelagem termo-mecânica fisicamente não linear de materiais refratários considerando os efeitos de danificação utilizando o Método dos Elementos Finitos. Inicialmente é feita uma descrição geral dos materiais refratários com foco em suas características termo-mecânicas, destacando principalmente suas propriedades elásticas e comportamento de amolecimento, e demonstrando sua considerável dependência da temperatura. Algumas considerações são feitas com relação à evolução dos modelos de simulação numérica aplicados a refratários, iniciando-se com os modelos lineares elásticos até o uso de modelos constitutivos complexos. O modelo de fissuração distribuída utilizado para calcular a perda de rigidez elástica é então apresentado, juntamente com a fundamentação matemática pertinente e sua relação com os parâmetros físicos do material. Para ilustrar a aplicabilidade do modelo alguns exemplos são apresentados, discutindo-se suas principais capacidades com relação ao projeto de estruturas refratárias.

Oct 30, 2017

By Patrick Tassot

Increased worldwide highly competition in steel market imposes innovative measure for the steelmaker targeting cost reduction and climate-friendly steelmaking process in order to have the ability to withstand the pressure of the market. At the same time the demand for high purity and highest quality steels continues to grow from year to year, especially in the sector automotive in transportation of oil and gas, in the construction Industry and in the manufacture of heavy plate. As they allow producers to be up to the requirements while allowing expanding their product mix, new secondary metallurgical treatments have become a must additionally to standard equipment elements of steel plants modern. Most of these treatments occurs in the steel ladle increasing the pressure to ensure a reliable and as possible neutral reactor. Intelligent solutions for refractory lining ladles should integrate better adaptation to the operational process parameters and the high reliability/availability at the best cost/performance. This challenge has conducted Refratechnik to develop new concepts to overcome the frontier between shaped and unshaped materials and that’s what will be covered in this paper.

Aug 17, 2017

By Giuseppe Pintaude

This study aims to evaluate the effect of specimen preparation on the dry sliding wear behavior of CA-6 NM stainless steel. Two different surface finishing manufacturing processes were applied: lapping and metallographic polishing. The wear tests were conducted in reciprocating ball-on-flat system, performed for two loads: 5 or 8 N. For all test conditions, hardmetal ball was employed as counterbody. The surfaces were evaluated using 3D interferometry technique to determine their surface roughness, including texture analysis regarding isotropy. Surface characterization results indicated the presence of texturing and preferential orientation, since the parameter Str was smaller than 0.5 for samples of both the studied conditions. Two distinct levels of isotropy evaluated through Str parameter were achieved: 0.13 for lapping and 0.3 for metallographic polishing process. It is clear from wear tests that the variation of average surface roughness is the key point for tribological behavior of CA-6 NM stainless steel.

Jul 31, 2018

By Andressa Pereira dos Reis Croucillo

O desenvolvimento de impressoras 3D permitiu uma maior produção de peças e próteses médicas provenientes de polímeros termoplásticos como PLA e ABS, para produção de filamentos. Este trabalho avaliou as características mecânicas de próteses impressas, em determinada temperatura, de filamento PLA. Foram impressos diversos corpos de provas, para a realização de testes de tração, verificando que a configuração com densidade 100%, espessura de 0,4 mm e direção de impressão de 45° e 135° apresentou melhor resultado de resistência mecânica. Realizaram-se também, simulações matemáticas para análise de resistência à queda e flambagem. O conjunto de testes físicos e matemáticos determinou que o PLA não atendeu os requisitos para aplicação deste como próteses.

Oct 30, 2017

By Uwe Wilhelm

Pittini Group has contracted Danieli in 2011 for the supply and replacement of the existing EAF at Ferriere Nord Plant in Osoppo. This was a very challenging project: giving the fact that the Meltshop was operating already under very high performance level, there were many elements involved for the project to improve (reduce the amount of charges, promote highest possible chemical energy utilization, allow best optimization on existing transformer power, modification on Drop Out box and Water Cooled Duct, Hydraulic System for EAF, Scrap Bucket design to fit to new EAF with existing loading and transport system, Automation System Review and Upgrade) as well as limitations of the existing installation (limited space, lifting capacity building and cranes and the required solutions for fast shell and roof exchange). All furnace parts, as well as installation engineering, were developed and discussed carefully with the Customer to either provide proven and reliable concepts, but also to define solutions for fast installation/maintenance access and quick exchange for offline turnaround. In the end, from disassembly of existing equipment up to the first heat of the new furnace, only 38 days were necessary. First heat was made on January 24th 2013, on the 6th production day 32 heats where produced at nominal design capacity and 28 days after start up 100,000 t liquid steel have already been produced.

Jul 30, 2018

By Ronaldo Santos Sampaio

This paper call attention to increasing ratio of oxygen depletion from atmosphere besides the global worries about CO2 concentration increase in the atmosphere. It highlights the big mistake in considering Carbon Capture and Storage, CCS, as a way to reduce the increasing concentration of CO2 in the atmosphere. As a hypothetical example it presents an existing pseudo-ecosystem of manufacturing that has real windows of opportunity to increase its share in the global materials production industry, even in highly industrialized countries. As a suggestion and example the author point out possibilities to almost fulfill the proposed simple rules to be considered inside an ecosystem of manufacturing utilizing the production of steel via biomass versus fossil coal. A relevant and difficult rule to be attained in a quasi-ecosystem of manufacture is to be a near zero atmosphere oxygen depletion integrated process. The industrial alternatives that utilizes the actual photosynthesis are the ones that can reach a higher ecosystem of manufacture’s index. It is presented an ideal integrated steelmaking process where the gaseous, liquids and solid residues generated in one part of the system are or can be utilized in the other parts of the same system. A potential ecosystem of manufacture to produce primary iron is illustrated in the paper.

Aug 17, 2017

By Douglas Glenn Stalheim

Production of structural hot strip coils in yield strengths up to 700 MPa and higher is increasing worldwide. In addition to requiring higher strengths, structural designs require good formability, toughness and weldability. Toughness and formability come from optimization of ductility properties while weldability comes from lower carbon equivalent alloy designs. The key to the production of optimized cost effective hot strip produced structural coils is to create the correct balance of a proper alloy/processing design to create as fine and uniformly distributed cross sectional grain size as possible. In addition to the creation of the fine/uniformly distributed cross sectional grain size, the correct microstructure needs to be created. In the higher yield strength grades, not only does the grain size/distribution play a role but a proper understanding and control of microalloying precipitation kinetics is required. This paper will present various examples of hot strip alloy designs to produce cost effective hot strip structural coil in yield strengths up to 700 MPa with good ductility and weldability. In addition, steelmaking/casting parameters will be discussed to assure successful production. Optimized reheating, rolling and cooling parameters of these alloy designs will be introduced in an accompanying paper.

Aug 17, 2017

By Henrique Silva Furtado

This paper presents the results obtained on the exchange of an original old blow charge model for a new up-to-date state of art global model, employing optimization techniques and process modelling, and, the results obtained in terms of fluxes consumption reduction and the introduction of user friendly tools and practices.

Aug 17, 2017

By Flávio Parreiras Marques

A microabrasão é uma técnica para produzir desgaste abrasivo em escala micrométrica. Neste trabalho estudamos uma liga fundida de cobalto com composição química próxima à da superliga comercial Stellite 6com composição eutética sendo a matriz constituída por uma solução sólida de cobalto, cromo e molibdênio que embebe uma grande quantidade carbonetos eutéticos de cromo. O objetivo deste estudo é avaliar a resistência ao desgaste bem como os micromecanismos dominantes através de ensaios de microabrasão. Foram usados três diferentes tipos de lama abrasiva, sílica, alumina e carbeto de silício com uma concentração de 0,1 g/cm3, carga de 0,3 N e uma distância deslizada de 48 metros. O menor coeficiente de desgaste foi obtido com sílica e o maior com carbeto de silício. O micromecanismo dominante foi o riscamento com riscos em toda superfície da amostra e presença de indentações apenas na matriz.

Aug 16, 2017

By Ângelo Siqueira da Silva

Este trabalho teve por objetivo avaliar o potencial gratifizante de adições de alumínio, em conjunto com inoculante a base de silício, diretamente no fundo do basquete antes do basculamento da panela de metal líquido no basquete da máquina centrífuga, a fim de produzir tubos centrifugados de ferro fundido nodular de matriz majoritariamente ferrítica. Amostras extraídas da ponta e cabeça dos tubos, sem e com distintas adições de alumínio, foram submetidas a tratamentos de recozimento (1050, 1000 e 900ºC), a fim de serem analisadas por meio de análise microestrutural e dureza Brinell. De acordo com os resultados obtidos a incorporação de alumínio ao ferro fundido foi mais efetiva para a incorporação de 1,7% de Al no ferro fundido, permitindo obter um ferro fundido nodular de composição ligeiramente hipereutética, com adequada grafitização e matriz 100% ferrítica, mesmo nas condições testadas com menor temperatura de encharque (900ºC) no recozimento, e com dureza dentro das especificações para a aplicação.

Aug 16, 2017

By Bianka Nani Venturelli

Estudou-se o efeito do tamanho de grão austenítico nas propriedades de tração do aço Hadfield refinado com Hf. Estas propriedades foram comparadas com as de um aço Hadfield sem refino, ambos com a composição química de acordo com a norma ASTM A128 – grau B2. Adicionalmente, foram usadas técnicas de caracterização macroestrutural, microestrutural e fractográfica. A caracterização macroestrutural mostrou que o aço Hadfield com adição de Hf apresentou tamanho do grão austenítico (600 ?m) aproximadamente cinco vezes menor do que o do aço Hadfield sem refino (3000 ?m). Os resultados do ensaio de tração mostraram um pequeno aumento (~6%) no valor do limite de escoamento com o refino do grão, em acordo com a Equação de Hall-Petch para materiais austeníticos. No entanto, os resultados dos ensaios de tração do aço Hadfield refinado mostraram aumentos que não foram previstos para as propriedades de resistência à tração (~37%), alongamento (~53%) e tenacidade (~88%). O exame fractográfico dos corpos de prova de tração indicou predominância do mecanismo de fratura dúctil para o aço Hadfield sem refino, enquanto que o aço Hadfield refinado apresentou predominância do mecanismo de fratura intergranular dúctil.

Oct 30, 2017

By Giuseppe Pintaude

The use of two-dimensional shape parameters to characterize abrasive particles is a possible approach to express their angularity. Nonetheless, in sliding abrasion, especially in pin abrasion testing, coated papers structure plays an important role and even its damage during the wear process should not be neglected. This manuscript discuss the limitations of two-dimensional shape descriptors in distinguishing wear caused by relatively hard particles, indicating that the wear data obtained in sliding abrasion tests are unable to distinguish different types of coated papers used when only the two-dimensional particle projection is considered for shape characterization.

Jul 31, 2018

By Marcella Gautê Cavalcante Xavier

As ligas livres de chumbo (Lead-free solder alloys) potencialmente utilizáveis em processos de soldagem branda, tais como as ligas à base de Sn, vêm sendo estudadas como alternativas para substituir as ligas do sistema Sn-Pb. Em vista disto, o presente trabalho, aborda tanto a análise das características microestruturais formadas durante a solidificação transitória das ligas eutética Sn-0,2%Ni e hipereutética Sn-0,5%Ni, quanto a determinação das suas respectivas correlações com os parâmetros térmicos de solidificação: velocidade da isoterma eutética (VE) e taxa de resfriamento (?E). Para tanto, as ligas foram solidificadas unidirecionalmente no sentido vertical ascendente e em regime transiente, e caracterizadas por técnicas de microscopias ótica e eletrônica de varredura. Na liga hipereutética Sn-0,5%Ni, o aumento da quantidade de Ni na liga influenciou tanto o comportamento térmico quanto o espaçamento celular (λC), proporcionando maiores valores de ?E, porém, λC mais grosseiros.O intermetálico NiSn4 formou-se na região eutética de ambas as ligas, enquanto que na liga Sn-0,5%Ni, as fases primárias identificadas por EDS-MEV foram NiSn4 e Ni3Sn4. A transição morfológica celular/dendrítica(?E> 1,2ºC/s) ocorreu apenas para a liga eutética, enquanto que as células regulares da liga hipereutética deram origem as células do tipo placas(?E> 1,4ºC/s).

Oct 30, 2017

By J. Kempken

Driven by customers, especially from the automotive sector, the supply of 100% prime quality has become essential. Furthermore the implication of quality costs and the yield of first class products define the steel companies' profitability and overall success significantly. The SMS group together with its subsidiary MET/Con has developed a comprehensive solution to assess the product quality over the production and processing chain. Process and production parameters originating from various data sources of the process automation are examined on their impact of quality related characteristics.Expert know how and comprehensive operational experience is translated into a quality guideline and a regulation framework as the sensitive core of the PQA solution.Once implemented, the system identifies immediately steel grade specific, deviations from ideal standard and proposes corrective actions including a final evaluation for each product at each processing step.The X-Pact® PQA (Product Quality Assessment) system is a substantial tool for root cause quality analysis and provides the required support to the production team. It will become an integral part of the corporate quality management system.

Aug 17, 2017

By Luiz Filipe Cardoso de Oliveira, Alex Milton Albergaria Campos, Paulo Santos Assis

Em usinas siderúrgicas integradas a coque, o carvão mineral tem papel fundamental principalmente na produção de coque metalúrgico, que será utilizado nos altos-fornos para produção do ferro-gusa. O coque é produzido a partir de misturas, de carvões minerais com diferentes propriedades, formuladas para atender os requisitos operacionais do processo de coqueificação e a garantir a qualidade do ferro-gusa que será produzido nos altos-fornos. Além disso, está mistura deve ter o menor custo possível uma vez que a maior parte do carvão metalúrgico utilizado no Brasil é importado, representando assim uma grande parcela do custo do aço. O grande desafio do setor é obter misturas de carvões que atendam a coqueria e produzam coque com alta qualidade e baixo custo. Para tanto, é necessário uma otimização de vários processos, desde a compra e transporte do carvão até sua estocagem, formação das misturas e abastecimento da coqueria. Com isto, este trabalho vem com o objetivo de sugerir uma otimização e planejamento da mistura de carvão para a coqueria com a utilização de rejeitos plásticos de menor valor agregado na mistura que possibilitem a produção de coque com menor custo e com a qualidade exigida no processo de fabricação de aço.

Oct 1, 2019

By Claudeir Carvalho Silveira

Para produzir os aços bifásicos galvanizados com revestimento de Zn-Fe as tecnologias de galvanização foram adaptadas visando à produção de aços com alta resistência, resistentes à corrosão e boa conformabilidade. Desta forma, e considerando as deformações obtidas na estampagem tornou importante a caracterização em laboratório da influência do nível e do caminho de deformação na geração de trincas do revestimento com Zn-Fe aplicado a um aço bifásico. O presente trabalho avaliou o efeito dos caminhos de Deformação Uniaxial, Deformação Plana e Estiramento Biaxial Simétrico na evolução das trincas do revestimento Zinco-Ferro (Galvannealed-GA) e sua conectividade considerando o aço base Dual Phase 600. Foi observado que aumento da área composta por trincas ocorre com o aumento do nível de deformação para todos os caminhos avaliados. O Estiramento Biaxial Simétrico foi o caminho de deformação que mais influenciou no aumento da área com trincas na superfície do revestimento e na conexão destas trincas com o aço base. Isso ocorreu em função do estado de tensão (tração-tração) imposta à superfície e à seção dos revestimentos. Mesmo sendo observada a conectividade das trincas com o aço base não foi verificado visualmente defeitos de desplacamento do revestimento tais como Powdering e Flaking.

Aug 16, 2017

By Wolfgang Linden

The emerging demands on higher steel grades call for improvements in the operation of production units and a corresponding increase in automated processes, and therefore international steel producers require viable functions. The avoidance of slag carry-over to secondary metallurgy processes is essential for achieving steel grade qualities and reducing alloys in order to compensate slag residues in the downstream unit. The automatic tapping procedure in BOF converters will be supported by the implementation of reliable measurements used in high-end steel plants. Automatic tapping will help to achieve the following: Reduced slag carry-over, improved yield, increased reproducibility, improved working environment and safety and operation with minimum possible crew. The automatic tapping procedure is capable of being implemented in new or retrofitted installations.

Aug 17, 2017