Search Documents

By I Hustwick

New Zealand Steel Mining Limited operates two independent sand mining operations on the West Coast of the North Island of New Zealand. Waikato North Head 30 km south of Auckland supplies ironsand concentrate as the raw feed for New Zealand Steel's works at Glenbrook and Taharoa 70 km further south, exports ironsand concentrate to Japan.   Taharoa uses two sets of six low pressure Warman centrifugal pumps in series to load bulk ore carriers 3 km off shore through two underwater pipelines. Waikato North Head delivers the ironsand to Glenbrook 18 km through a 200 mm ID buried pipeline using two stages of high pressure positive displacement (HPPD) pumping.   A high level of operating and maintenance expertise has been developed since commissioning the two systems which are proving to be reliable, efficient and of minimal impact environmentally.

Jan 1, 1990

By G. de B. van Niekerk

This paper briefly outlines some mining technology that is used with success in Australia but is not yet fully utilized in South Africa. The following aspects are discussed: improved rotary-drill bit performance, use of trucks and load haul- dump units underground, long-hole raising, blasting techniques, and the use of butterfly roofbolt plates for support.

Jan 1, 1989

By T. J. Driscoll

Methane-air mixtures can ignite as a result of sparking or rubbing of materials, particularly by impact involving light alloys and rusted steel where an exothermic thermite reaction can occur. This report reviews the published literature and describes a new method utilized by the Bureau of Mines for studying the processes occurring during collisions of light metals with rusted steels. The method involves measuring the spectra of sparks and explosions in methane-air mixtures using a photodiode array. Initial results obtained using magnesium and aluminum alloy 6061-T651 projectiles striking rusted steel are reported. These results indicate that the continuous parts of the spectra show a larger intensity for incendive sparks compared with nonincendive sparks, with the largest relative change in the higher energy, ultraviolet region. An unexpected shift of the intensity maximum for the continuous parts of the spectra towards the infrared region was observed for the more incendive sparks. Evaluation of rusted steel samples with electron microscopy, energy-dispersive X-ray spectrography, and Auger electron spectroscopy after they had been impacted by aluminum alloys indicated that aluminum was transferred to the steel in the form of islands that became larger as a function of increasing projectile velocity.

Jan 1, 1982

By Edward G. Cunney

[Track in underground bituminous coal mines was investigated and technology has taken from other industries in order to Main information on conditions that impair the safety and efficiency of the track and to develop guidelines ad useful information on the constriction, inspec¬tion and maintenance of mine track. Volume l contains information oil the investigations, observed track conditions, useful technology from railroads and other industries, derivations of track condition descriptors and limits, conclusions, and recommendations. Volume 2, Guidelines, contains recommended standards and practices for mine track. It includes the relation of track conditions to safe speeds; descriptions and limits for measurable track features such as gage, descriptions of conditions for track components that are normally not measurable, such as subbase soils; construction requirements and techniques; inspection requirements and methods; and methods for managing and performing track maintenance work. As a research product, it 0005 nut repeat the summary or derivations. Volume 5, Inspection Handbook, summarizes recommended standards and procedures from Volume 2 and provides related information for read: refer¬ence by inspectors in tin mines. As a research product to be used in mines, it does not repeat the summary, derivations or references.]

Jan 1, 1977

By J. L. Robson, C. M. Bristow

mass flow rates of particles and air (the loading ratio).

Dec 1, 1994

DURING September, the Coal Commission pre- pared for issue a series of 18 reports on varied aspects of- the bituminous coal industry; the final report, dated Sept. 22, sums up the facts and offers recommendations addressed to Congress, to the industry, and to the public. The few following paragraphs are selected: Bituminous coal is the real foundation of that great industrial and transportation structure which enables more than a hundred million people to live in America and be so well supplied with things necessary for their health, comfort; and convenience; it also furnishes domestic fuel for two-thirds of the homes of the land. The distribution of the output of the bituminous mines tells the story: 28 per cent. goes to the railroads, 25 per cent. to the boiler houses of factories and mills of all kinds, 15 per cent. to the coke ovens and gas plants, 10 per cent, to the homes, 7 per cent. to steel plants and the same percentage to power plants and street railways, 4 per cent. is exported, 2 per cent is used for power at the coal mines, and the remaining 2 per cent. goes to the seaboard for steamship fuel. Bituminous coal enters into interstate commerce on a scale approached by no other commodity; less than a fourth of the coal mined in the United States fails to enter interstate com-merce. All but one of the 45 coal producing districts in the United States ship coal outside the State in which it is mined. Three hundred miles of cars loaded with coal is the daily output of the bituminous mines of the United States. The public-welfare element in coal is seen in the dependence of public health and safety on an unfailing supply of fuel, in the close connection between the prosperity of most industries and the uninterrupted operation of the coal mines, and in the obvious fact that without coal the great network of railroads which binds together this great country would be idle. The railroads and the public utilities, themselves so clearly obligated to render what-ever public service is demanded of them that the constitutionality of their public regulation is unquestioned, are of all industries most dependent upon coal. Thus, coal makes up over 35 per cent. of the operating cost at the gas plant and over 25 per cent. at the electric power station, and in the operating expenses of. a railroad the cost of coal is the largest single item, next to labor. The practical logic that half a century ago clothed with a public interest the steam locomotive and in later years the electric-power station must recognize a large element of public service in the coal mine that furnishes the necessary energy to both locomotive and power-plant.

Jan 10, 1923

By G Liu

Seventy-nine gold deposits and prospects have been discovered in theJiamusi region of northeast China, and constitute one of the most important gold metallogenic belts in China. All these endogenic gold occurrences can be subdivided into three main deposit types: 1. porphyry related; 2. metamorphic-intrusive hosted, and 3. sediment-hosted deposit.   The first two types of gold deposit are spatially and temporally related to Mesozoic Yanshanian granitoid intrusions with hydrothermal activity channelled along crustal-scale fissures. The ultimate cause of the Yanshanian magmatism is considered to be the subduction of Pacific oceanic lithosphere beneath the Eurasian continent. In contrast, the chemical sediment-hosted deposit is typified by the Dongfengshan gold deposit, and genetically related to Proterozoic sedimentation and Mesozoic igneous activities.

Jan 1, 1995

Sixteen papers concerned with the technology and utilization of low-rank fossil fuels are presented as the proceedings of the 1973 lignite symposium. This symposium, the seventh in a series of biennial meetings, was cosponsored by the Bureau of Mines and the University of North Dakota.

Jan 1, 1974

By George A. Savanick

This paper reviews advances in the art of borehole (slurry) mining made by the Bureau of Mines from 1974 to 1980. The design of a proto-type borehole-mining tool (BMT) developed by the Bureau of Mines is pre-sented along with production data, reclamation data, and an application of the BMT to the mining of coal, uraniferous sandstone, oil sands, and phosphate ore. The BMT was first used near Wilkeson, WA, where steeply pitching metallurgical coal was mined at 8 st/h from a depth of 25 to 75 ft. Next, 940 st of uraniferous sandstone was mined at 8 st/h from a depth of 75 to 100 ft in Natrona County, WY. One thousand short tons of oil sands was mined in Kern County, CA, at the rate of 14 st/h from a depth of 110 to 150 ft in 1979. Most recently, 1,700 st of phosphate ore was produced at 25 st/h from deep (230-to 250-ft) deposits in St. Johns County, FL. Progressive improvements were made in the borehole mining technique. These include the use of the hydrostatic head of a water-filled borehole for roof support, and the development of methods to survey and backfill mined-out cavities.

Jan 1, 1987

By J. J. Forbes

The activities of the Bureau of Mines include the development and testing of self-contained oxygen breathing apparatus and other devices for respiratory protection, the development and tasting of devices for detecting dangerous or noxious mine atmospheres, and the training of men in the mineral industries in the use and care of this equipment to enable them to render effective service in mine rescue and recovery operations following mine fires and explosions, or under other conditions where irrespirable gases may be found in mines or mining plants. The first use of self-contained oxygen breathing apparatus for com- bating mine fires and explosions in the United States dates back about 30 years. Previous to that time, exploration for any distance ahead of fresh air was virtually impossible without great risk to life; moreover, the men called upon to render service at mine disasters were not well-versed in the properties and physiological effects of gases likely to be encountered. It was also impossible to work ahead of fresh air to restore ventilation, and if many stoppings were blown out by an explosion, air had to be introduced into whole areas or sections at once without knowledge of the conditions ahead; moving an explosive mixture of methane and air over live fire had to

Jan 1, 1938

The following pages discuss the objectives, the background, and scope of work of an industrial engineering analysis of far-,n haulage systems in underground retreat coal mining. This study ran concurrently with an existing industrial engineering study of methods of improving safety and production efficiency in underground pillar extraction. 1. OBJECTIVES The objective of this project was to provide basic data inputs that will inpart knowledge as to the major constraint to pillar extraction sections. Furthermore, the industrial engineering study will suggest ways to optimize haulage systems and to develop more efficient work practices and operational techniques that will maximize equipment utilization.

Jan 1, 1975

By M. A. T. Cocquerel, M. G. Burcher, J. G. Eacott

"This paper is based on work carried out to examine the feasibility of increasing the smelting rate of two oil-fired calcine-charged reverberatory furnaces . Various constraints prevented physical enlargement of the furnaces and so allention turned to the use of preheated combustion air or oxygen enrichment to bring about the required increase in production. As a basis for further calculation, a furnace heat balance is determined using the smelting metallurgy and combustion data for the current operation. Various other operational data are tabulated and compared with similar data from other operating copper smelters.New heat balances are derived for various levels of combustion air preheat at the current smelting rate, and the effects of air preheat on oil consumption, combustion air and waste gas volumes are tabulated. These data are used to demonstrate the level of increased throughput which would be obtained before constraints in existing gas handling equipment are encountered.A similar exercise for oxygen enrichment is set out, with oil consumption, combustion air and waste gas volumes at various enrichment levels tabulated for the current smelting rate. These data are in turn used to demon strate the smelting rate which would be achieved at a practical level of enrichment before waste heat boiler and gas handling constraints are encountered.The energy implications for both cases are summarized."

Jan 1, 1980

By D. D. Bush

Based on the results of this study, the underhand cut and fill stoping method, with mass destressing, is an effective method for controlling rock bursts and falls of ground for deep mining in the Coeur d'Alene Mining District. The procedure can be utilized to pull highly stressed pillars by converting from conventional overhand stoping methods or used as a primary recovery system. During the demonstration, only one minor rock burst occurred, with no injuries. The system facilitates accurate placement of vertical boreholes for effective mass destressing. Each mining cut is filled with cemented sandfill overlying a timbered mat that forms the back for the succeeding cut. For this demonstration, a cemented fill was mixed on the surface and piped to the stone. Costs for pillar recovery by this method are comparable and are considered cost effective over conventionally timbered overhand mining as a pillar recovery method.

Jan 1, 1982

By G. L. Oldright, J. D. Sullivan, W. E. Keck

"An apparatus and procedure developed in the laboratory of the South-west Experiment Station of the Bureau of Mines are capable not only of determining the rate and volume of penetration of solutions into porous materials but also of determining the total volume of voids within particles of porous material, and the density. The method is applicable to ores, bricks, concretes, tiles, filter bottoms, or other porous materials of this nature. As will be made clear in the descriptive matter to follow, the method measures (a) the volume of voids within the porous materials and is not concerned with the interstitial space between the particles.Porous materials usually contain some large voids and also pores that are capillary in nature. To measure the total volume of voids in a sample it is necessary to replace the gas or gases within the voids with some liquid of known density. The large cavities can be filled quite readily, but under ordinary conditions a long time may be required to fill capillary pores. As many porous materials are of a decomposable nature it is necessary to evacuate the porous materials and then submerge them in a liquid of known density to bring about saturation in a short time. Then by the use of a hydrostatic balance the volume of porous material (solid itself) can be determined. To determine the volume of porous material plus voids it is necessary to coat the sample with some material, such s paraffin, which will prevent solution from entering the voids; then, by means of a hydrostatic balance, the volume of porous material plus voids is determined and by subtracting that of the porous material from this the volume of voids is ascertained. The rate of penetration of solutions can be determined either (a) by measuring the change in weight as the sample becomes saturated when immersed ni a liquid of know density, or (b) by measuring the volume of liquid penetrating with a dilatometer. In either instance, due to the fact that some penetration takes place as soon as the sample comes in contact with solution and before a reading can be taken, the sample must be paraffined to determine the total volume of penetration. Since many porous materials partly decompose and disintegrate in liquids the rate and volume of penetration can better be measured by dilatometer than by the change in weight, as saturation takes place when immersed in a liquid. The details of procedure for determining (a) total volume of voids, and (b) rate and volume of penetration are given in this paper."

Oct 1, 1930

By S. G. Beattie, N. Mojtabai

A study was carried out which aimed to: determine the effects of blasting on excavation perimeters and nearby slopes; establish a low-cost blast monitoring and field observation programme to determine peak particle velocities and blast damage; and to develop criteria for observable blast damage that are based on the peak particle velocity. Full-scale production blasts in a large open pit copper mine were monitored and studied to develop damage criteria for various rock types. Better blast designs can be achieved by correlating the results of blast monitoring with field observations of damage at the pit walls and on benches. Back-break and damage are related to blast-induced ground vibration. Peak particle velocity is accepted as a reliable measure for the prediction of ground vibration levels. Empirical models for the estimation of rock damage can be developed and used for blast design. The models are used to determine the zones of damage within the rock face. Rock damage models can also be used to design trim shots to achieve further reduction of back-break in more critical areas

Apr 1, 1996

By C. E. Wood

A special appropriation made by Congress in July 1940 provided funds for the investigation of methods for recovering manganese from low-grade [ ] domestic deposits. These funds were assigned to the United States Department of the Interior, Bureau of Mines. A committee, identified as the Technologic Committee on manganese of the National Research Council, National Academy of Sciences, was appointed to recommend the allocation of the funds for investigation of the more promising projects.

Jan 1, 1942

By C. E. Wood

A special appropriation made by Congress in July 1940 provided funds for the investigation of methods for recovering manganese from low-grade [ ] domestic deposits. These funds were assigned to the United States Department of the Interior, Bureau of Mines. A committee, identified as the Technologic Committee on Manganese of the National Research Council, National Academy of Sciences, was appointed to recommend the allocation of the funds for investigation of the more promising projects.

Jan 1, 1942

By Robert J. Rothwell

Underground mining of coal by longwall mining methods has not been a predominant technique in Ohio. To date, only five mines in the state utilize this method, however, the technique has sparked a certain amount of controversy. As a mining technique, longwalling was introduced into southeastern Ohio in the early 1970's but it did not attract public attention until the mines began moving into privately held surface lands. This occurred coincidentally at about the same time that the state of Ohio began to regulate the environmental impacts of underground mining. Prior to the passage of the Surface Mining Control and Reclamation Act in 1977, (SMCRA), Ohio's reclamation law, Chapter 1513 Ohio Revised Code (O.R.C. 1513) did not regulate underground coal mines. As a result of SMCRA, the Ohio Statute was amended in 1978, to include regulation of the surface effects of subsidence. The inevitable result was that existing mines were immediately subject to regulations that were not considered during the initial mine planning process. (For an excellent survey of Ohio Laws that deal with coal mine subsidence, see Zima, 1985. ) The problem faced at that time by both the coal industry and the Ohio Division of Reclamation (the agency within ODNR charged with implementing O.R.C. Ch. 1513.1, was that of attempting to superimpose permitting requirements, and design performance standards onto mines that' had been operational for a number of years.

Jan 1, 1986

By V. E. Edlund

As part of a research program for recovering alumina from domestic nonbauxitic resources, the Bureau of Mines investigated a lime-sinter, caustic leach technology for anorthosite. This report discusses the unit operations--feed preparation, sintering, and leaching. Acceptable pellets for the bench-scale sintering studies were prepared from mixtures of minus 200-mesh anorthosite and limestone using water alone as the pelletizing agent. Heating pellets at 1,270° to 1,360° C for periods of 0.5 to 2 hr, followed by a 15-min soaking period at 700° C and cooling to room temperature, produced a sinter that dusted to more than 90 pct minus 65 mesh. The weight ratio of limestone to anorthnsite was critical in producing sinter exhibiting good dusting and leaching characteristics. A ratio of 2.0 was optimum for the bulk samples of anorthosite and limestone used in this research. Leach solutions from lower ratio sinters were unstable; gelation became progressively more severe with higher ratio sinters. Leaching the dusted sinter with 10-pct Na2CO3 at 60° C extracted 85 to 90 pct of the alumina in a product solution containing about 50 g/l A1203. Leach residue in contact with pregnant solution tended to set up as a rigid gel as a result of cementation, comp action, and gelation. The presence of a calcium-sodium zeolite [(Cn,Na2)6?(Al2Si04)12?27-3OH20] in the ungelled residues seemed to be the main difference between gelled and ungelled residues.

Jan 1, 1982

By G. W. Jones

The results presented in this report deal with the elimination of explosion hazards of ether-oxygen mixtures by the addition of helium. The method is based upon the fact that every combustible gas, vapor, or dust will not burn or explode when the oxygen content of the mixture is reduced below certain definite values. These critical oxygen values are usually different for each combustible, varying with the percentage of the combustible present in the mixture and also with the inert gaseous material used to reduce the oxygen content of the mixture.

Jan 1, 1941