Search Documents

By Norman F. Schulz

The technical excellence of separation achieved in a mineral concentration process, or any other process where two constituents of any kind are physically separated from each other, is expressed uniquely and quantitatively by the separation efficiency (E,): E. = (R - R,), where R is the percentage of the valuable constituent and R, the percentage of the waste appearing in the concentrate. The separation efficiency meets all the usual requirements of a true efficiency and is independent of the nature of the process used. It can be visualized as the percentage of the feed material that, in effect, actually undergoes complete separation while the rest of the feed is distributed randomly and unchanged into the two separation products. The problem of quantitatively assessing the results of a mineral concentration process recurs whenever one tries to decide which of two similar test results is more desirable. Although economic factors may greatly influence the eventual choice of process, they usually have very little to do with the technical excellence of a separation and are, therefore, not a consideration at this point. Concentrate grade and recovery, used simultaneously are the most widely accepted measures of performance, and if both the grade and the recovery are greater for one case than for another, the choice is simple. However, when the results of closely competitive operations are compared, it often occurs that one set of test results shows a higher grade and a lower recovery than another and the choice is no longer obvious. Laboratory investigations of a mineral concentration process applied to a given feed material can often be designed to yield successive paired values of concentrate grade and recovery over the practical range of the course of a separation process.' These results may be plotted as some combination of the cumulative values of grade, weight recovery, or unit recovery in the concentrate. The resulting correlations for two slightly different sets of conditions can then be compared qualitatively, or even quantitatively in particular cases.2 Such comparisons are not applicable, however, to individual concentration test results. The reduction of a separation test result to a single efficiency figure, preferably as a percentage of ideality, would afford the simplest and most precise means for comparing the results of competitive tests. The effective proportion of feed material that undergoes complete separation in any real concentration process, hereafter referred to as "separation efficiency," is such a figure. It is essily calculated from the usual feed and product data and can even be evaluated, in many cases, from data in publications describing various concentration processes. Mineral Concentration Processes and Their Evaluation Mineral Concentration Processes: The overall concentration process may be subdivided into a liberation process which severs the bonds between unlike mineral species, and a separation process, which sorts the resulting liberated particles into two products—a concentrate rich in mineral A and a tailing lean in mineral A. A perfect mineral concentration process is represented by the idealized scheme shown in Fig. 1 in which liberation and separation are not differentiated. The feed mixture consists of two mineral types which are completely liberated early in the process and then sorted by type. All the mineral particles of type A which respond uniquely to the selection forces acting in the ideal separator, report to the concentrate, while all the mineral particles of type non-A report to the tail-

Jan 1, 1971

The placer mining industry of the West Coast region of the South Island is based largely around the production of alluvial gold, although other valuable minerals are also present. Since the first major discoveries in 1864-65, reported gold production has totalled around 264 t (8.5 Moz). During the past 10 years, annual production has totalled around 1460 kg (47,000 oz). It is anticipated that gold production over the next three years will continue at a level of 1400-1800 kg.   Annual gold production peaked during 1866 at approximately 17,170 kg (550,000 oz) and has not exceeded 100,000 oz since 1885. This reflects the ease with which gold was won from shallow, rich deposits that were present at many localities. Subsequently, there has been a general decline in the availability of this type of deposit, a trend that will continue in the future. This paper outlines the present state of placer mining in the West Coast region, gives some historical background to the industry and briefly predicts future trends.

Jan 1, 1997

Close spatial relationships between the deposits of the Etheridge Goldfield (23 000 kg of bullion) and various regional geological and geophysical features suggest that genesis of the ore deposits was a multi-stage process that started with magmatic and metamorphic stages in the mid-Proterozoic, climaxed with structural and hydrothermal stages in the late Palaeozoic and terminated with an oxidation enrichment stage in the Cainozoic. Acceptance of this hypothesis permits classification of the Georgetown region into areas likely to contain deposits of the Etheridge type and those unlikely to do so. Consequently there is little scope for the discovery of extensions of this field. However, the stratigraphic interval between the source rocks of the Etheridge field and stratigraphically bigger host rocks of the Croydon field may contain disseminated replacement gold deposits of the Carlin type. The potential host (pyritic carbonaceous and locally dolomitic siltstone of the Candlow Formation) is locally faulted and cut by granitoids and the extension of a mineralised, long-standing zone of structural weakness.

Jan 1, 1980

By G. G. Barbante

Anode slimes produced during copper electrorefining are a valuable source of silver, gold, selenium and tellurium. The conventional pyrometallurgical process for treating slimes involves preliminary leaching in sulphuric acid followed by smelting in a reverberatory furnace with fluxes, but it is slow and has many recycle streams. The chemistry of the phases and the reactions that occur in slimes smelting are poorly understood and and this prevents major improvements to the process. Laboratory-scale experiments were conducted using unleached slimes, with and without the addition of fluxes and under neutral, oxidising and reducing conditions. Results show that selenium is readily removed as gaseous selenium dioxide and that molten Cu-Ag-Se-O phases form when fluxes are added. Oxidation-refining of these phases by air injection and flux addition can result in the formation of silver suitable for further electrorefining

Aug 1, 1995

By Pervez Patel, Martin G. Frohberg, Demetrios Papamantellos

Model experiments were carried out on the mass transfer of iodine between n-hexane and a 4 2 X 10-3 M aqueous sodium hydroxide solution. The influence of mechanical stirring by means of small gas bubbles (ca. 0.01 ml in volume) on mass transfer was examined in independent experiments. The results were described with the help of the penetration theory and in the case of bubble stirring with the help of a mathematical model based on this theory. S LAG-METAL reactions, especially those in steel-making processes, often occur under conditions where gas is evolved in the form of bubbles that break through the slag-metal interface. It is known that stirring by means of bubbles increases the mass transfer coefficient, but there has been very little quantitative work done in this field. Because of the difficulties that attach to experimental work at high temperatures this study was confined to model experiments at room temperature. EXPERIMENTAL APPARATUS The transport of iodine from an n-hexane layer into a weak sodium hydroxide solution was studied a) with stirring by means of bubbles and b) with mechanical stirring. The apparatus for the experiments with bubbles consisted of the cell, two Dreschel bottles filled with hexane in order to saturate the nitrogen flow, one flow meter, and a nitrogen gas cylinder fitted with a fine-regulating valve. Fig. 1 shows the cell consisting of a glass cylinder 33 cm in height with an overall diameter of 7.5 cm embedded in a copper flange. The flange is connected to a Plexiglas plate and to the gas inlet. The Plexiglas plate has holes of 0.2 mm diam bored into it which are spaced 1 cm from each other. For the experiments with mechanical stirring the bottom of the cell was sealed off by a Plexiglas plate. The upper layer was stirred by means of a glass stir-rer and the bottom layer with the help of a magnetic stirrer in a counter rotatory direction. Both stirrer speeds could be varied continuously. EXPERIMENTAL PROCEDURE Iodine dissolves in n-hexane producing a stable violet color thus enabling the iodine concentration in

Jan 1, 1970

An understanding of the origin of mineral deposits and their relationship to local and global geotectonics is essential if regional targets for mineral exploration are to be chosen. Volcanism, metamorphism and tectonism are especially significant for the origin and emplacement of mineral deposits, which, far from being fortuitous oddities of nature, occupy well defined positions within distinctive lithofacies. Thus, suggestions for mineral exploration targets can be made taking into consideration the position of 'fossil' convergent and divergent plate tectonic boundaries to indicate areas of specific types of mineralisation. To be borne in mind, though, that level of exposure, time and location of magma generation are all additional and important controlling factors. To further understand the importance of the above parameters, one must refer to the concept of paired metamorphic belts (Miyashiro 1973) which develop during an orognic cycle. These belts are generally constructed in such a way that an ophiolite type complex with metamorphic grades related to high pressure and moderate temperature regimes is flanked by an area of calc-alkaline volcanism and granitic activity with metamorphic grades within a region of high temperature and low pressure. The former situation is usually the seat of primary magmatic mineralisation, whereas the latter contains base metal. Deposits of acid plutonic and volcanic association. As will be seen later, this particular metamorphic-volcano-orogenic situation is well developed in some parts of New Zealand. For the present purpose a distribution of potential ores as related to plate tectonic processes is given below:a) Divergent plate boundaries: primary magmatic Ni-Cu, Pt,Cr, PeS2 and Cu, Pb,Zn in hot brines-hydrothermal environments Mn deposits.b) Convergent plate boundaries: stratabound Cu-Fb-Zn-Ag of felsic volcanogenic association. Porphyry eu-Au of island arc type, porphyry Cu-Mo of continental type. Cu, Au, Y, Sn, Hg, Sb of vein type and replacement lode related to granitic activity.c) Au of hydrothermal vein association, related to late dynamo-metamorphic events. By virtue of ocean floor spreading, regions of divergent plate boundaries are eventually juxtaposed or welded n to areas where plate collisions occur. This is then followed by partial melting due to various causes, just above the descending plate; thus creating a zone of acid to intermediate magmatism. The final picture is that of an orogenic zone with the paired metamorphic belts outlined above.

Jan 1, 1976

By Ernest J. Conway

Seventy-four human factors research and development projects were identified for possible Bureau funding. The projects were based on (1) literature surveys, (2) reviews of accident statistics and reports, (3) interviews with equipment manufacturers, MSHA, and Bureau personnel, and (4) site visits to 26 mines. The projects are divided into the following categories: those related to (1) mobile equipment, (2) maintenance shops and areas, (3) plants and mills, (4) organizational factors, (5) safety programs/data, and (6) training. The projects were rated by industry and MSHA people in terms of benefit to the industry. Projects were placed into three categories of priority. The highest priority contained 25 projects with 26 in Category 2, and 23 projects in the lowest category.

Jan 1, 1982

By H. S. Price, J. C. Cavendish, R. S. Varga

A numerical formulation of bigh-order accuracy, based on variational methods, is proposed for the solution of multidimensional diffusion-convection-type equations. Accurate solutions are obtained without the difficulties that standard finite difference approximations present. In addition, tests show that accurate solutions of a one-dimensional problem can be obtained in the neighborhood of a sharp front without the need for a large number of calculations for the entire region of interest. Results using these variational methods are compared with several standard finite difference approximations and with a technique based on the method of characteristics. The variational methods are shown to yield higher accuracies in less computer time. Finally, it is indicated how one can use these attractive features of the variational methods for solving miscible displacement problems in two dimensions. INTRODUCTION The problem of finding suitable numerical approximations for equations describing the transport of heat or mass by diffusion and convection simultaneously has been of interest for some time. Equations of this type, which will be called diffusionconvection equations, arise in describing many diverse physical processes. Of particular interest here is the equation describing the process by which one miscible liquid displaces another liquid in a one-dimensional porous medium. The behavior of such a system is described by the following parabolic partial differential equation:

Jan 1, 1969

By M. Karmis

The algorithms for the mathematical modeling to predict productivity of underground room-and-pillar mining systems are well known and documented. These algorithms consider the time-varying relationships between mining equipment for a given geometry of operations as well as other constraints. This paper presents WebConSim, a newly developed, Web-based, user-friendly computer simulation tool for the Windows environment. The simulator is easily customized for use by field engineers, planning engineers, and management and will help mine operators plan the optimum mining sequence for different mine geometries and equipment layouts. Program output includes production data and equipment utilization indices, as well as time driven event chains that can be used for virtual reality presentations.

Jan 1, 2001

By Albert W. Deurbrouck

The percentage of coal cleaned mechanically has increased greatly in the past 30 years. This technological change in preparation methods, accompanied by mechanical innovations in most phases of coal mining, has enabled the industry to supply quality coals at competitive prices. The Bureau of Mines has contributed to this progress by conducting research on coal-preparation problems, by evaluating the performance of domestic-and foreign-made preparation equipment, and by recording advances as they occur in industrial coal-cleaning practices. The Bureau's work in this field is recorded in the more than 150 technical and scientific publications listed in this volume. These reports, published by the Bureau over the past half century, document the Nation's progress in a vitally important phase of fuel technology.

Jan 1, 1961

By Patricia R. Devine

This appendix documents the mathematical approach to deriving the components of change presented in this report. The formulation closely follows that contained in Chapter IV of the documentation for the BEA 1977 Input-Output Tables.' The basic elements for the calculations include the "use" matrix (U), the "make" matrix (M), and any of the ten columns of final demand (generically represented by the symbol y). The use matrix contains information about changes in the technological processes of production, while the make matrix describes the nature of secondary product production in each industry. We adhere to BEA conventions in maintaining careful distinctions between commodity output (c) and industry output (x). The industry-by-industry 1-0 tables supplied by NYU for use in this analysis are square matrices, with the number of commodities and the number of industries both equal to 85. The BLS table for 1982 (commodity by industry) was aggregated and adjusted to be consistent with the earlier tables. The three basic steps for estimating components of change proceed as follows for each column of final demand. 1) Calculate the actual change in output of each commodity for each of the four time periods: 1963-72, 1972-77, 1977-82, and 1963-82.

Jan 1, 1988

By W C. Cook, S J. Mathews, A H. Purvis

The Golden Cross Gold Mine is located at the head of the Waite kauri Ri ver, 8 km northwest of Waihi near the southern end of the Coromandel Range. The mine produces gold and silver from epithermal veins hosted by Miocene andesitic flows and pyroclastics of the Coromandel Group. Golden Cross is owned in joint venture by Coeur Gold NZ Ltd (80 per cent) and Viking Mining Company Ltd (20 per cent). Mining is by open pit and underground methods. Mineralisation in a near-surface sheeted/stockworked vein zone is mined from the open pit. The deeper Empire Vein System is mined from underground where higher grade mineralisation is restricted to generally discrete veins. The open pit stockwork zone is west of and offset from the updip trend of the Empire Vein System. The Empire (hangingwall) Vein strikes generally north-northeast and dips steeply west. Dips become subvertical at greater depth. The hangingwall vein is a well developed, generally continuous structure with relatively high gold grades. A complex footwall vein system forms shallow west-dipping offshoots to the hangingwall vein. Structure and gold grades become increasingly erratic away from the hangingwall vein. The better developed footwall veins carry economic grades and high 'spot' grades over 50 g/t Au are not uncommon. Highest gold grades are associated with tightly crustiform banded sections of quartz veins and with dark fine grained siliceous breccias. The main hangingwall vein occupies a major north-northeast trending fault structure, the Empire Fault. Footwall veining forms within subordinate splinter fault zones. There has been extensive multidirectional pre-, syn- and post-mineralisation faulting. Fault manifestation is highly dependent on host rock characteristics. The central part of the hangingwall vein and surrounding silicified country rock has been shattered by a major fault structure, the West Mine Fault, forming a poorly consolidated, blocky quartz-breccia ore zone. Away from the more brittle ore zones and associated silicified envelope, wide clay-filled shears mark the major fault trends. Development of the deposit is considered to have occurred in two distinct stages related to separate episodes of dilational jog movement on the Empire Fault. The first phase reactivated the pre-existing Empire Fault as a dilational fissure with subordinate splinters on the footwall side. The Empire Vein System (hangingwall and associated footwall veining) formed during this phase. A second phase of renewed movement with further dilation resulted in more extensive fracturing of the Empire Vein and surrounding country rock and formed the sheeted/stockwork veining of the open pit. An upwards/westward migration of the hydrothermal system is assumed but fluid pathways between underground and open pit veining are unclear. Ore extraction and mining geology methods have responded to improved understanding of the grade and structural variability, and changing ground conditions inherent in the vein system. The underground mine produces ore from flatback cut and fill, post-pillar and bench stopes. Open pit and underground ores are campaign milled through a conventional CIP plant.

Jan 1, 1993

By T. R. A. Davey

The fundamental principles by which bismuth may be removed from lead by pyrometallurgical processes are enumerated. Qualitative discussion of the phase diagrams concerned is followed by presentation of quantitative diagrams. Brief mention is made of the practical aspects. Data presented show how chemical lead (<0.005 pct Bi) may be produced by the Jollivet, Dittmer, and Kroll-Betterton processes. BISMUTH is an element whose properties are very similar to those of lead, and its minerals are associated to a greater or lesser extent with nearly all the major lead ore deposits of the world. In consequence, the lead produced contains bismuth unless a special debismuthizing process is practiced. There does not appear to be any published comprehensive review of the effect of bismuth as an impurity on the properties of lead, and there is some uncertainty as to the beneficial or detrimental effects of small amounts of bismuth in lead used for particular applications. Standard specifications of most countries stipulate a maximum bismuth content of 0.005 pct for chemical lead. With one exception, this specification is met only by lead producers whose ores are relatively bismuth-free, or whose refineries are electrolytic. In lead for certain applications a higher bismuth content is preferred by some fabricators.&apos; In contrast to the refining for silver, copper, and antimony, the refining for bismuth does not usually result in a large overalil economic gain from the sale of byproduct. Thus, debismuthizing is customarily practiced only if market conditions demand a lead with a bismuth content lower than that produced by classical refining; i.e., softening, desilverizing, and zinc refining. Until this century, debismuthizing was carried out only a:; an incidental result of desilverizing, as later described. This century has seen the development of the Betts electrolytic process—the only successful one of many electrolytic processes proposed and patented —and a number of precipitation processes based on the pioneering work of Kroll,&apos; although only one of these, the Kroll-Better ton process,&apos; is in wide commercial use today. It is proposed in this paper to deal only with the pyrometallurgical processes, excluding those based on aqueous electrolysis. Historical Background Prior to 1833 silver (and incidentally bismuth) could not be removed from lead. To recover silver from rich bullion, the only course available to lead refineries was to cupel the bullion, forming a slag of litharge. The first slag tappings or skimmings, on reduction, yielded soft lead of very low silver and bismuth contents. Intermediate skimmings yielded a lead of somewhat higher silver and bismuth contents, which could if desired be recupelled. The last skimmings yielded a litharge very high in bismuth, which could by successive oxidation and reduction cycles be separated into high purity bismuth, and lead returns. This oxidation reduction process, with modern operating techniques, can still be used today to produce a portion of a lead refinery&apos;s output of very low bismuth content, as discussed later. In 1833 Pattinsone discovered that lead bullion could be purified of silver and bismuth by fractional crystallization, the primary lead crystals formed by partial freezing being purer than the melt. Repeated processing in pans produced a lead containing as little as 0.02 pct Bi. The simple explanation of this

Jan 1, 1957

By D. McSwain-Santos

Soda ash is the trade name for sodium carbonate, a chemical refined from the mineral trona or naturally occurring sodium carbonate-bearing brines (both referred to as natural soda ash) or manufactured from one of several chemical processes (referred to as synthetic soda ash). It is an essential raw material in glass, chemicals, detergents and other important industrial products. Production U.S. soda ash production during 2004 increased to10.9 million Mt (12 million st). Five companies comprised the domestic soda ash industry. Four were in Wyoming operating five plants. One was in California with one plant.

Jan 1, 2005

By William G. Doepken

With most of the mining industry emerging from the deepest business recession in 50 years, primary attention must be given to surviving in a business climate where dominant foreign competition, depressed prices, and potential overcapacity hang heavy over much of the industry. While already shackled with regulatory constraints, restrictive work rules, and high labor costs, mine operators are faced with the difficult task of reducing costs and improving productivity while operating at less than full capacity. To counter these nearly over-whelming factors, the mining industry must continue at the national level to seek regulatory relief and a rational policy toward foreign competition from government-controlled mines. In addition, dialogue with labor organizations must continue to minimize the impact of labor costs, cost escalators, and antiquated work practices. Although national and international actions have a tremendous impact on the future of domestic mining operations, local actions by mine operators to dramatically improve mining productivity will strengthen the industry&apos;s competitive stance. Before any substantial progress can be made, however, mine operators must recognize and define areas that depress productivity and establish goals and measures for improvement. Once problem areas are defined, a combination of technological and motivational concepts can be applied to improve productivity. Timing of Improvements While there is an immediate need for productivity improvements, only certain concepts offer near-term improvement potential while others must, of necessity, fit into a mid-range or long-range time frame. Near-term solutions (immediate to one year) likely will involve motivational concepts - work incentives and training - coupled with available technological concepts that require little capitalized development or site testing. Mid-range solutions (one to three years), by contrast, will include technological improvements in mining equipment, techniques, and systems automation. These concepts require a longer period of capitalized development and site testing before use. Long-range solutions (three years or more), which include adoption of new mining methods and computerized control systems, will appear only after prolonged research and capitalized development programs. Motivational Improvements Developing motivational con-

Jan 11, 1983

By Robert B. Fulton

The use of industrial minerals by the chemical industry as raw materials for manufacturing and in processing spans a wide assortment of minerals. This chapter aims to supplement rather than duplicate the commodity chapters. Its objective, to describe the uses of industrial minerals in the manufacture of chemicals, is attained by considering minerals used by the chemical industry in terms of the chemical element required and by giving particular emphasis to market factors. The mineral aspect, which is covered in the commodity chapters, is subordinated and attention is focused on the chemical and market aspects. Condensing this broad subject into a few pages permits treating only the most important elements derived from industrial minerals. The elements derived from petroleum, hydrogen and carbon, which quantitatively dominate as raw materials for the chemical industry, are omitted, as are the metallic elements and the minerals covered in other "use" chapters such as phosphorous, potash, and nitrogen for fertilizers and titanium dioxide for pigments. After eliminating on this basis, our definition leaves six elements of major importance: boron, bromine, chlorine, fluorine, sodium, and sulfur. These elements are treated individually under separate headings. Salt brines have particular importance as raw material sources for the chemical industry as shown in Table 1 "Salt Brine Derivatives" (Anon., 1967), which charts the chemical compounds derived from four types of brines: (1) Owens Lake type brines which are sources of boron and sodium compounds; (2) Midland type brines from which bromine, iodine, and chlorides of calcium, magnesium, potassium, and sodium are derived; (3) Searles Lake type yielding boron, bromine, lithium, magnesium, potassium, and sodium compounds; and (4) Silver Peak type produced mainly for lithium. Table 2 (Jones, 1973) affords an overview of the chief industrial minerals, the chemical products derived from them, and end uses of the products.

Jan 1, 1975

By E. J. (Kirk) Conway

Thirty-five years ago underground coal mining equipment consisted of simple but rugged machines powered by electric motors and hydraulics. The machines were maintained by maintenance personnel armed with a basic knowledge of hydraulics, electricity, and mechanical design. Over the years the the machine has been transformed into powerful complex mining systems. The maintenance burden has also increased. During this period significant advances have been made in maintainability engineering and system design techniques. Many of these innovations and techniques are applicable to the design of underground mining equipment. The objectives of this project were to; (1) determine the extent to which maintainability design concepts and principles have been applied to the design of underground coal mining equipment, (2) try to assess the impact of equipment design for maintenance on productivity and safety, and (3) develop a maintainability design guideline to enhance the design of new or rebuilt equipment. An equipment design review was completed at ten operational coal mines. Interviews were also conducted with mine management, safety, and maintenance personnel to identify machine specific design advantages and problems. Visits were also made to six original equipment manufacturers to discuss the design of their equipment for maintenance. Volume I presents an overview of the protocol used and a summary of the findings. Volume II includes the maintainability design guide for underground mobile mining equipment.

Jan 1, 1989

By J. Bennetts

As part of its mission to develop technology that will help increase the supply of critical and strategic minerals from domestic resources, the Bureau of Mines has investigated methods for beneficiating platinum-group metal ores from the Stillwater complex, Montana. This report presents the result of a bench-scale study employing froth flotation to recover a sulfide concentrate containing platinum-palladium values from a mineralized gabbro. Best results were obtained with a flotation scheme utilizing a mercaptobenzothiazone collector and sulfuric acid. Rougher concentrates containing approximately 11 oz Pt-Pd/ton and 90 pct of the metal values in the ore were obtained. Subsequently, cleaner concentrates containing approximately 26 oz Pt-Pd/ton and between 80 to 85 pct of the Pt-Pd values in the ore were prepared.

Jan 1, 1980

Education and training research is a major component of the Bureau of Mines human factors research program. The goal of human factors research is to enhance human performance for the purpose of improving both safety and the profitability of the minerals industries. This is achieved through the design of mining equipment, work tasks, management procedures, and development of human resources. This proceedings volume presents several new developments that are helping to improve the quality and efficiency of health, safety, and occupational skills training in the mining community. Several papers address the issue of how to teach and assess miner abilities to deal with underground mine emergencies. Other papers examine practical procedures for defining and cost justifying the integration of structured training and other performance improvement strategies to enhance the proficiency of the work system.

Jan 1, 1988

By Susumu Uchiyama

This machine was manufactured for excavation of the Roppongi station of the Tokyo Metro Line 12. This machine can excavate both the platform and the rail track at the same time in locations where the traffic is congested and has following features: A multi-centered TBM of the size of 7.06(H) x 13.18(W) m The world first H&V TBM, with right and left machine parts articulated vertically and separately for position control A large erector for simultaneous erection of column and central segments of special shape to construct a highly reliable tunnel This paper reports the design concept, construction, and work record.

Jan 1, 1999