Search Documents

By A. Galibois, M. Fiset, T. Vo Van

"RÉSUMÉUn groupe de 22 objets prov enant des Forges du St-Maurice a été étudié de façon systématique par analyse chimique et examen métallographique afin de préciser leurs caractéristiques et d'en évaluer la qualité métallurgique.La plupart des échantillons de fe r forgé et d'acier sont hétérogènes tant au niveau structural que composition chimique. L'examen de quelques produits fin is a mont ré qu 'on appliquait des traitements superficiels bien que le contrôle métallurgique fût plutôt empirique.AbstractA group of 22 specimens originating from ""Les Forges du St Maurice"" has been systematically studied by chemical analysis and metallographic examination in order to determine their characteristics and to evaluate their metallurgical quality.The bulk of the forged iron and steel samples are heterogeneous from both their microstructure and their chemical composition. Observation of a few finish products has permitted to establish that surface heat treating was applied although its metallurgical control was rather empirical."

Jan 1, 1984

By Andrew J. Brennan, Jonathan A. Knappett, Lewis Hamilton, Michael J. Brown

"Abstract This paper investigates the compressive behaviour of screw piles in sands and the key design parameters which control this. These types of foundation elements have typically been used as screw anchors onshore (i.e. for their tensile capacity), but there is increasing interest in their potential use as compression piles for supporting offshore marine renewable energy (MRE) devices (e.g. wind and tidal turbines) in deeper water. For such foundation applications, the compressive capacity is as important as the tensile capacity and is not well understood, particularly in cohesionless soils which are a likely seabed condition in MRE applications. A 1-g laboratory study was initially conducted on small scale model screw piles in sand beds of various relative density between 25 – 88%. These experiments were used to validate a Finite Element (FE) model having a stress-dependent constitutive model, making it useful for future up-scaling of the pile size for field applications. Following validation, the FE model was used to conduct a parametric study on the effects of flange spacing ratio (s/Dflange) and flange to shaft diameter ratio (Dflange/Dshaft). By using a validated FE model for this study, it was possible to observe the failure mechanisms (through the shear strain distribution) within the soil and correlate these with the pile capacity. This information was then used to comment on the most optimal (cost-effective) pile design for supporting compressive loads. This study represents a key step towards producing design tools appropriate for the design of screw piles in MREapplications.IntroductionAs defined in this paper, screw piles consist of a central small diameter hollow steel shaft, around which thin circular steel flanges run. Their principle of operation is that the flanges are spaced so as to trap the soil between them, thereby acting as an equivalent solid pile of the outer flange diameter, with a fully-rough ‘shaft’ interface (as shearing is soil-soil). One of the most important design decisions relates to the spacing of the flanges – if the flanges are spaced too far apart, then the soil will not be effectively trapped and the pile have a lower axial capacity and stiffness (controlled by the shaft friction along the central shaft and the bearing resistance arising from the individual flanges; If the flanges are spaced too close together, then there are potentially flanges which are not contributing to the pile capacity, therefore making the pile more expensive than it needs to be."

Jan 1, 2014

Recent improvements are described in several techniques for ground control in underground mining. Promising methods for analysis and mitigation of rockbursts are discussed. Methods of assessing damage to underground excavations from repetitive seismic loading are reviewed. Analysis of mining-induced surface subsidence is discussed.

Jan 1, 1989

By J. A. Ober

"In 2015, the estimated value of nonfuel mineral production in the United States decreased by 3 percent from that in 2014 (Table 1), mainly as a result of decreased metal and metallic mineral prices, especially iron ore, copper and precious metals. Lower metal prices were attributed to decreased consumption, especially in China and increased global inventories. Several U.S. metal mines were idled in 2015, including the only U.S. rare earths mine at Mountain Pass, CA. Downstream processors also were affected, with smelters and refiners either shutting down or idling production lines. Increases, however, took place in the value and quantity of production of industrial minerals, especially those used in the construction sector, including cement, construction sand and gravel and crushed stone. Trends in mineral-related sectors of the domestic economy, except for iron and steel manufacturing, aluminum manufacturing, coal mining and metals mining, all experienced growth (Table 2).Discussion of mine production is frequently segmented according to the type of materials produced within the broad categories of metals and industrial minerals (also known as nonmetallic minerals). Industrial minerals can be further subdivided as construction aggregates and other industrial minerals. Metals tend to have higher unit values but very low production quantities compared with those of industrial minerals, which have higher production quantities but are lower-valued materials, such as crushed stone or construction sand and gravel. Therefore, for discussion and analysis of the performance of the nonfuel minerals industry, the value of production is used rather than the tonnage produced. Tonnages of construction aggregates are orders of magnitude larger than those for most other mineral commodities thus making direct comparisons based on weight meaningless (Fig. 1).Mineral industry performanceThe estimated value of domestic nonfuel mineral production, including metals ($26.6 billion) and industrial minerals ($51.7 billion), in 2015 declined to a total of $78.3 billion, from $80.8 billion in 2014 (Table 1). However, as shown in Fig. 2, minerals remained fundamental to the United States economy, contributing to the real gross domestic product at several levels, including mining, processing and manufacturing finished products. Net exports of mineral raw materials and old scrap were $14.4 billion. Domestic raw materials, along with domestically recycled materials, were used to produce mineral materials worth $630 billion. These mineral materials, including aluminum, brick, copper, fertilizers and steel, and net imports of processed materials (worth about $32 billion) were, in turn, consumed by downstream industries with a value added to the gross domestic product estimated to be $2,490 billion."

May 1, 2016

By K. E. Wood, K. J. DiRocco, L. A. Becker

The Russia Wharf segment of the Silver Line Phase II Project for the MBTA incorporated ground freezing and underpinning during New Austrian Tunneling Method(NATM) tunneling through timber pile foundations, urban fill, and abandoned wharf structures beneath two historic 7-story buildings with steel frames and masonry facades. During construction, the project team implemented an extensive program to monitor, evaluate, and mitigate the ground and building movements caused by the various construction activities. Mitigation included freeze cycling and building raising/lowering to compensate for ground movements and safely maintain the serviceability and occupancy of the buildings. In this paper, we present the history of the freeze, tunnel construction, and thaw-related movements that occurred and the building response that we observed.

Jan 1, 2005

By J. MacFadyen

The U.S. cement industry experienced its best year ever during 2004 in terms of production and shipments of cement. Clinker, portland and masonry cements production and shipments were up considerably. Clinker production as reported to the U.S. Geological Survey (USGS) was 87.75 Mt (96.73 million st), an increase of 5.4 percent. Gray and white portland cement production from domestic and imported clinker was estimated to be 91.6 Mt (101 million st), up 5 Mt (5.5 million st) from 2003.

Jan 1, 2005

By Mary L. Pearson

Ibis report summarizes the results of the contract. Included are summaries of existing legislation pertaining to outcrop barriers and a state-of-the-art survey of outcrop barrier designs and related, mine closure techniques. Six sites were inspected in the field and are presented as case histories The data analysis presented includes a computer modeled seepage analysis, an overburden blew-out analysis, and a wedge stability analysis. The results tit these analyses are interpreted to form recommendations for coal outcrop barriers which will minimize seepage and the potential for failure. Supplementary support and reinforcement alternatives are also discussed.

Jan 1, 1981

By A. J. Vivyurka

"This is a talk about the experiences that Rio Algom Mines Ltd. has had in the Elliot Lake uranium area trying to make the tailings more compatible with the surrounding environment. To get a better idea of the problem that we are associated with we have to go back to the location. The Elliot Lake uranium area is situated about half way between Sault Ste Marie and Sudbury and is about 20 miles north of Lake Huron. In 1950, uranium was discovered along the north shore of Lake Huron and by 1961 we had up to 9 mines operating in the area. Then the United States Atomic Energy Connnission withdrew their contracts so that at present there are only 2 mines operating. From all the mines that we had operating, we ended up with 7 tailings areas. From these 7 tailings areas we have 5 sites where we have active treatment or rehabilitation. There is the Pronto site where we are treating uranium tailings and copper tailings. There is the Lacnor-Nordic site which is located just out of Ellio Lake. The Milliken-Stanleigh site is in the Crotch Lake area. The Panel tailings is off the north end of Quirke Lake and finally there is the operating property of Rio Algom Mines at Quirke Lake.To understand fully the problem with this rehabilitation we have to look at the constituents of the ore. The ore body is a quartz conglomerate with uraninite and brannerite as the uranium bearing minerals in a fine ground mass of quartz, sericite and pyrite which separates the larger quartz pebbles. The approximate composition of the ore is: 80% quartz, 13% chlorite, 7% pyrite and 0.2% uranium minerals. The processing method also adds a few constituents to the final tailings."

Jan 1, 1975

By J M. Laboz Bernard

Among the numerous technical evolutions in the blasting environment we are going to describe below the concep

Jan 1, 1995

By Adilson Curi

"A fundamental aspect in the development of any open-pit mining project is the determination of the mineable mineral reserves, obtained with the design of the so-called ultimate pit limits. In this paper, firstly the Vulcan software applied over the data of MR phosphate deposit will be introduced. Modeling of the ore deposit has been done by geostatistical and conventional methods by using geological data of 41 diamond core samples. Insitu geological reserves were estimated to a level of accuracy to support detailed mine planning. Ore body has been divided into regular three dimensional fixed blocks. The ultimate pit limits of the model deposit weredetermined by the vulcan program by an optimizing technique. Additionally, the approximate location of the deposit and drillholles and the contour map of the ultimate pit limits generated by the vulcan program are presented. "

Jul 17, 2000

By M. Leroux, S. R. Rao, J. A. Finch

"Poor Pb-Zn selectivity during Pb flotation in laboratory tests on a Mississippi Valley-type Pb-Zn ore was traced to apH effect. In the pH range, 9.5 to 11.0 sphalerite floated readily without copper activation. Compared to sphalerite flotation with copper activation this procedure gave equivalent selectivity but reduced flotation rate.Possible mechanisms of this sphalerite flotation without copper activation are discussed. Activation by Fe(OH)2 is suggested, the Fe- + ions being derived from superficial oxidation of pyrite in the ore. IntroductionGalena and sphalerite commonly occur together. A typical procedure, using xanthate collectors, is to float the galena first, at pH - 8, followed by flotation of sphalerite after activation with copper (II) sulphate at pH - 10 (to depress pyrite).Flotation tests following this procedure in an undergraduate laboratory course with a Pb-Zn ore from Polaris failed to achieve consistent selective flotation of galena. Occasionally a considerable amount of sphalerite, even though unactivated with CUSO4, floated. This was traced to accidentally high pH. A systematic study was carried out which revealed that sphalerite floated readily in the pH range 9.5 to 11.0 without activation by CuSO4 This paper describes the results of the study and discusses a possible mechanism of this flotation of sphalerite."

Jan 1, 1987

By N. E. Idenyi

The effects of compositions and firing temperatures on the physico-mechanical properties of blended Nsu fireclay and Nkalaha redbrick clay have been investigated. The clay samples were compounded according to the following ratios: 10:90, 20:80, 30:70, 40:60 50:50, 60:40, 70:30, 80:20 and 90:10 in the order Nsu: Nkalaha respectively, and test samples made and fired at 9000C, 10000C 11000C and 12000C. The properties tested for were the modulus of rupture, porosity, shrinkage, apparent density, water absorption and bulk density. From the results obtained, it is inferred that the blends have a maximum service temperature of 11000C, with the 30: 70 blend presenting the best characteristics. A conclusion is drawn to the effect that the blend could be adapted for the production of ceramic earthenware, electrical porcelain pin insulators, cement manufacture and for refractory linings where temperature requirements are less severe.

Jan 1, 2006

By Robert V. Berryhill

Reconnaissance studies of beach deposits along approximately 220 miles of the shoreline of Bristol Bay, Alaska, were made to determine if more detailed investigations were warranted. In addition to preliminary mapping of the deposits, samples were obtained from auger borings spaced at 1-mile intervals in key areas; shovel samples were collected to supplement the borings. Most samples were roughly concentrated in the field; magnetic separation tests, petrographic analyses, and determinations for radiometric equivalent uranium, gold, platinum, iron, and titanium were made in the Bureau of Mines laboratory at Juneau, Alaska. Spot samples from some beaches along the shores of the Alaska Peninsula indicate small deposits containing up to 10 percent recoverable titaniferous magnetite; some larger deposits were indicated to contain from 1 to 2 percent total heavy metal, principally as titaniferous magnetite. Significant amounts of other commercial minerals were not detected.

Jan 1, 1963

By D. C. Kaliampakos, A. G. Benardos

The existence of quarries near or even within the boundaries of urban centres is the cause of many environmental problems, despite their significant contribution to the cities’ development. Hence, the question arises as to how quarrying activities can be compromised within the spirit of sustainable development in big cities. In the case of Athens, two dominant, though opposite opinions have been formed. The first argues that all quarries must be forced to suspend their activities as soon as possible; the second presses for the continuation of quarrying. Consequently, the question is transposed on the dilemma between improved environmental conditions and economic development. This paper demonstrates that if a complete redesign is employed to specific, nonvisible quarrying sites, the continuation of quarrying activities is acceptable. It is a good compromise between the economical demand and environmental protection.

Jan 1, 2000

By G Q. Xie, J W. Mao, Y B Cheng

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The East China Mesozoic metallogenic province hosts the world’s largest resources of tungsten, tin, molybdenum, antimony and bismuth, with additional important gold, silver, mercury, lead, zinc, copper, uranium and iron deposits. These deposits form several giant metallogenic belts, including South China, Middle-Lower Yangtze River Valley, East Qinling-Dabie, eastern North China Craton and North-east China. Available data demonstrate that these metallogeneic belts are the products of episodic magmatic and related hydrothermal events between ~240 and ~80 Ma. Each magmatic-hydrothermal episode has produced distinct deposit assemblages that can be readily linked to the Mesozoic geodynamic evolution of East China, involving continental collision between the North China Craton and South China Block at 220–200 Ma, oblique subduction of the Izanagi plate under the Eurasian continent at ca 170–135 Ma and post-subduction extension and lithospheric delamination at 130–80 Ma. Metallogeny in north-eastern China is more complicated due to prolonged tectonic evolution related to southward subduction of the Mongolian–Okhotsk plate and westward oblique subduction of the Izanagi plate, and subsequent continental collision and post-collisional processes.CITATION:Mao, J W, Xie, G Q and Cheng, Y B, 2015. Mesozoic metallogeny in east China and their geodynamic processes , in Proceedings PACRIM 2015 Congress, pp 631–636 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By Qingzhu Li

The brewing industry byproduct, spent grain (SG), was evaluated for its ability to adsorb Ag(I) from aqueous solutions. Ag(I) adsorption was dependent on solution pH, contact time, adsorbent dose, initial Ag(I) concentration and temperature. The kinetic data were well described by pseudo-second-order kinetic model, indicating that chemical adsorption was the rate-controlling step. The equilibrium data followed Freundlich isotherm rather than Langmuir isotherm, suggesting heterogenity of the adsorption sites on spent grain. Ag(I) desorbed from Ag(I)-loaded spent grain was also evaluated in this study. HCl, NaOH, Na2S2O3 and ultrapure water were chosen as eluants and desorbed Ag(I)-loaded spent grain for 30min, Ag(I)-loaded spent grain desorbed in 0.1M Na2S2O3 exhibited higher elution efficiency as compared with other eluants. The results indicated that application of spent grain for adsorption and recovery of silver from aqueous solutions was feasible.

Jan 1, 2009

Session 1 ? Intro to MiHR ? Business Case for Aboriginal Inclusion ? Overview of the Mining HR Guide for Aboriginal Communities ? Two presentations of Programs featured in the Guide ?? The RAP Program from NWCC ?? First Nations Youth Employment Program PDAC-MM Session 2 ? Presentation from MAC ? Taking up the AFN Corporate Challenge ? Presentation on Mastering Aboriginal Inclusion in Mining About MiHR Who we are: ? National Sector Council for the Minerals and Metals Sector ? 18-person Board of Directors ? 100+ Industry Leaders volunteer on our project committees ? PPP - Funded by HRSDC and industry What we do: ? Identify national HR challenges and opportunities for the minerals and metals industry ? Create national solutions through collaboration, partnerships and Synergy

May 1, 2009

Recent accelerated exploration efforts in southwest China have progressively quantified the vast phosphate resources in the Yunnan Province. To date, according to Chinese geologists, potential reserves in the province may be on the order of 4 Gt, which would equal the entire US reserve base. Development of this vast reserve is underway at two sites located 60-70 km southwest of Kunming, the provincial capital of Yunnan. The first, the Kunyang open-pit phosphate mine, produces an estimated 1.5 Mt/a of 22-30% P20,5. The other project located north of Kunyang is the Haikou mine, which the Chinese consider a possible 2.0-Mt/a operation. Because average ore grades run 3% less than those of Kunyang, beneficiation will be necessary. While the latter project has been initiated on a small scale, it is basically still on the drawing board. Brown and Root and the US Bureau of Mines are assisting on the project. Both operations are under the direction a regional administration which reports to the Ministry of Chemical Industries in Beijing. Combined production from both mines could represent some 70% of China's future productive capacity. Ore reserves in the region are estimated at 400 Mt by local officials. Geology of the District The phosphates are considered Cambrian in age and rest on a Precambrian dolomite. The Indian Ocean, Chinese geologists say, may have been the original source. The line of deposition stretches on a trend from Vietnam in the southwest, through Yunnan, into Sichuan Province to the northeast. Because the area is considered very stable from a geologic viewpoint, large quantities of phosphate have been deposited and large outcrops are known to occur everywhere in the province, according to Chinese sources. The Kunyang and Haikou ore bodies are thought to be two wings of an anticline with the former the southern portion, and the latter the northern portion. Each ore body strikes on an east-west axis. While there are many localized phosphate operations throughout the province, the Kunyang mine is the premium producer. Kunyang's Mining Development The Kunyang open-pit mine was opened in 1966. During the early years, operations were considered somewhat disorganized. Systematic mine planning and normal operations were not initiated until just two years ago, according to mine management. In 1979, Kunyang finally reached its design capacity of 1.5 Mt/a. The ore body consists of two phosphate beds separated by a band of shale. The top layer of phosphate varies from 4 to 8 m, averaging 6 m. The middle shale layer is 2 in. The third layer, which is not as rich as the top, is approximately 4 m. To further complicate matters, the ore dips 15° to the south over a strike length that is currently undefined, but believed to be

Jan 3, 1980

By Albert Sauveur

It is delightful to read a technical paper like that of J. E. Johnson, The Effect of High Carbon on the Quality of Charcoal-Iron, presented in October, 1912, at the Cleveland meeting of the American Institute of Mining Engineers.' The clear, simple, and straightforward manner in which he describes his experiments and results makes you feel as if you had been, so to speak, at his elbow during the course of his investigations, while his method of procedure is so rational that you can fairly anticipate each step in the logical sequence of the tests performed. The following notes suggested by Mr. Johnson's paper are presented here in the hope that they may help, if only a mite, towards the final solution of a problem of considerable scientific and industrial importance. Physical Properties of Cast-Iron us. Its Ultimate Composition. Mr. Johnson writes that " an investigation along the lines of consumption showed that different irons have different characters totally independent of their analyses," and he declares that " the presence or absence of these elements [meaning carbon, phosphorus, silicon, and manganese] alone will not account for all, scarcely for a half, of the facts which have long been known." He further tells us that some foundries have " proved, by the most irrefutable tests, that they could take a certain iron of a given analysis and produce certain results," while with " another iron of the same analysis they could not produce these results at all." I feel confident that every experienced and thinking metallurgist will readily believe Mr. Johnson's statements and will share his views in regard to the hopelessness of inferring the

Jan 1, 1914

By W. D. Johnston, T. P. Thayer

THE minerals that collectively are known as chromite form an isomorphous series of the general formula (Mg,Fe) 0. (Cr,Al,Fe) 203. So wide is the range in chemical composition in this group that chrome ore consisting entirely of the mineral chromite may range from less than 30 pct to more than 60 pct Cr203. The most comprehensive published data on the chemical com- position of chromite are by Stevens,62 who made complete analyses of 52 samples of chromite concentrate from many localities in North, Cen- [ ] tral, and South America. These samples were mechanically purified to remove associated silicates and might be regarded as the cleanest chromite that could be obtained by any mechanical milling process. Fig 1 shows the predominant zone of isomorphism, within the triangular prism of composition defined by the mineralogical end members of the series, wherein his analyzed samples fell.

Jan 1, 1949