Search Documents

A process was developed to produce electrolytic manganese dioxide, suitable for use in high quality dry cells, from Risdon anode mud. ImpurItIes present In the anode mud were removed prior to the electrolysis which was performed from a manganese sulphate bath using the following conditions.Temp. 95°CH2S04 50-55 g/l.Mn2+ 55-60 g/l.Anode c.d. 10·0 A/sq. ft.Operation under these conditions yielded current efficiency and power consumption figures of 95 per cent and 0·8 kWh/lb respectively. The product conformed to battery manufacturers' specifications as regards physical and chemical properties and performed satisfactorily in a battery testing programme.

Jan 1, 1968

By Cassandra A. Wetzel

Rock socketed mini-piles are a desirable foundation alternative when design capacity is more than 40 tons and there is limited access. In this case history mini-piles were designed to support between 75 and 200 kips at 12 locations adjacent to a perimeter wall, a party wall and at cast iron column piers. Limited geotechnical information, low overhead clearance, and active building population tested the creativity of the team to get the piles installed. The key geotechnical concern during installation of the mini-piles was the presence of a glacial till layer above the bedrock surface that restricted the seating of the casing into bedrock with a track mounted drill rig. Soil loss during the advancement of the rock socket using an air hammer was excessive and increased the risk of subsidence. Over a three week period the engineer worked with the contractor to modify the design, means, methods, and materials to install piles with adequate load capacity. This paper will present the changes in design and construction methods that were required.

By P J. Hommert, D S. Preece

"Commercial development of the United States Oil Shale reserve will require substantial amounts of mining. In fact, even a modest 500,000 barrels per day industry requires a mining effort equivalent to nearly half of the current U.S. coal mining industry. Obviously, mining efforts on this scale will benefit from technological advances. There are a number of areas where advanced technology could impact mining. These include continuous miners, shale transport systems, and blasting. This paperexamines recent developments in computer modeling of blasting and assesses the likelihood of these advances being applied to practical oil shale mining problems."

Jan 1, 1989

By Vanessa C. Koppe

During ore body modeling normally additional samples are required to improve resources evaluation and mining planning. At this stage one rises the question about where additional samples should be located. Regular sampling pattern seems to be a reasonable choice, since all the regions within the deposit receive the same number of samples without a clear clustering. Nevertheless, values for certain attributes (grades for instance) from a mineral deposits may behave more erratic in some regions than others. Consequently, by adding samples to these regions could bring more benefit for reducing the uncertainty related to a transfer function such as Net Present Value (NPV), instead of adding samples to location of low grade uncertainty. Thus, for a given number of additional data, the test of a regular pattern and a pattern which add samples on areas of high uncertainty of the attribute of interest is worth. This paper presents an algorithm that allows the construction of these two patterns, automatically, on a software commonly used in the mining industry. The algorithm leads to a fast analysis on the efficiency of the two patterns in reducing the uncertainty associated with a transfer function.

Oct 1, 2009

Background: Frictional ignitions continue to be a problem facing the U.S. underground coal mining industry. Many methane igni-tions are associated with the impact of mining machine cutter bits on quartzitic material (e.g., sandstone) during the coal-cutting process. Most ignitions result in small methane-air fireballs often only a few feet in size and limited to the cutter head location. However, under certain conditions, frictional ignitions can lead to larger methane explosions and/or fires with the potential for causing serious injury or death to the mining machine operator and other nearby miners. The requirements for a frictional ignition are a flammable volume of methane-air and an ignition source. This source is usually the hot streak caused by the frictional impact of the mining bit on hard rock, and the frequency of occurrence increases with increased bit wear. Another possible ignition source is the fric-tional impact of rock on rock during a roof fall.

Mar 1, 2008

By Ben Bradshaw

Context ? Community engagement has become an increasingly significant and challenging part of mineral exploration and mine development; indeed, opposition from communities proximate to a proposed mine site has been known to derail technologically- and financially-sound projects. ? These cases suggest that mining firms need to better understand how to engage constructively with local communities in the pursuit of their claims. ? While a range of publications exist promoting various community engagement strategies, these recommendations, when viewed as a whole, are disjointed and largely untested in real development contexts. Aims of Presentation 1. Synthesize industry, NGO, government and academic publications focused on community engagement best practice in order to highlight those practices that are most commonly recommended. 2. Review the (Canadian) mining industry?s experience with some of these strategies based on existing case material in order to identify the extent to which commonly prescribed strategies are used and validated in practice.

May 1, 2010

By Andrew Jones

This paper discusses the worldwide market and cost environments for the bulk ferroalloys namely manganese alloys (ferromanganese, silicomanganese), ferrosilicon and ferrochrome (high-carbon ferrochrome, charge chrome). Annual average market prices since 1993 are presented graphically and analysed, and the main supply and demand trends for manganese, ferrosilicon and ferrochrome are summarized. The paper shows carbon and stainless steel output data for 1995, 2000 and 2005, mainly to demonstrate the rising importance of China as a ferroalloys market. Developments in ferroalloys capacity worldwide from 1991 to 2007 are discussed (plant start-ups and closures, ownership changes). Finally, the paper examines developments in the main cost factors for the bulk ferroalloys, i.e., chrome and manganese ore, electricity, carbon reductants and labour. Note that data for 2006 are estimated based on information available in November 2006.

Jan 1, 2007

By Detnet Solutions

1. “Daisy-Chain” concept The term “daisy-chain” stems from the fact that when the HotShot? detonators are connected there is a chain or electrical path for electrical current to flow from detonator A to detonator B, detonator B to detonator C etc until the path is terminated by an electrical means. The “daisy-chain” concept has long been used in electronic detonator systems, historically used in Expert Explosives’ ExEx 1000 5/6 wire system and currently in use in African Explosives Limited (AEL’s) Electrodet? electronic detonator system and has been adopted as the basis upon which the “auto-programmability” of the HotShot? electronic detonator system functions. HotShot? Detonators are connected to each other in a string, completing a “daisy chain”, and during the auto-detection mode of the control equipment, it is possible for the equipment to determine the order of hookup of the detonators as well as map the entire blast layout. The auxiliary components (Row Controllers & Branch Controllers) assist the control equipment in mapping the entire blast by indicating different points on the blast, i.e. The inflection point of a row of blast holes on a closed chevron timing pattern, the beginning of row of blast holes on open chevron timing pattern and extra blast holes or extra blast rows.

Jan 1, 2004

By B. R. Mohal, S. Chander

"A new technique to determine wettability of powders is presented in this paper. In this technique the times for immersion of individual particles from air into liquids, defined as imbibition times, are measured. Through the measurements of imbibition times for a large number of particles, it is possible to determine homogeneity/heterogeneity of a powder sample with regard to its wetting behavior. Quartz particles give a very narrow distribution of imbibition times showing a homogeneous wetting surface whereas coal particles give a broad distribution indicative of the heterogeneous nature of its surface. The imbibition time measurement technique is considered to have certain advantages over other methods to determine wettability of powders in surfactant solutions. In this study we have also compared the imbibition times with the wetting rate mea¬surements obtained by a modified Walker test.INTRODUCTIONSeveral methods are available for determining wetting characteristics of sol¬ids. Each of the methods has been used in the past to obtain very valuable information for comparing wetting behavior of various solids in a given liquid or for comparing the wetting behavior of several liquids for a given solid. Each method measures a somewhat different aspect of wetting and therefore quantitative correlations between techniques have been difficult. A general approach is to use a method in which close similarity between the technique and the application (where results of wetting measurements are to be used) can be maintained. The objective of this investigation was to develop a method which could be used to determine the wetting characteristics of single particles in surfactant solutions. Wetting of individual particles is of importance in cap¬ture of dust particles by sprays of surfactant solutions.METHODS FOR DETERMINING WETTING — A BRIEF REVIEWThe various methods available for measuring wetting characteristics of solids include: contact angle, immersion/sink time, bubble pick-up, induction time, capillary rise, and displacement method measurements. Some of the methods are briefly reviewed in the paragraphs that follow."

Mar 1, 1989

By Phillip Martin Warren

Safety and productivity are critical factors in the performance of the Australian Mining Industry. In this sense, the paper point out that while the multiple dimensions of both training and productivity make it difficult to quantify the relationship, it is clear from this study that organizations that conduct training consider that there is a very positive link. Training is seen as a very important activity by the vast majority of organizations surveyed, and is an activity from which they consider they are gaining significant, and often very substantial productivity benefits. Therefore, it predicts well for productivity of Australian enterprises which invest in training.

Sep 13, 2001

By H. Nan

Using the case of Qianqiu Mine, Yima Coal Mining Administration, theoretical analysis, laboratory physical simulation, and underground observation were performed to study the major parameters for fully mechanized sublevel caving mining method, including drawing spacing, drawing sequence, drawing numbers, and number of shields performing simultaneous drawing. The effects of those parameters on coal recovery and amount of waste rocks were also investigated. The optimal coal drawing technology for this case was obtained.

Jan 1, 2006

By Ren G. Dong, Richard McCormick, Dan E. Welcome

Vibration exposure at workplaces is generally multi-axial. The health effects of vibration exposure also likely depend on the vibration direction. Therefore, there is a wide interest in the simulation of multi-axial vibration in laboratory experiments. Advances in technology have led to the development of a new 3-D test system for studying hand-transmitted vibration exposure and health effects. The purposes of this paper are to introduce the system and to present the results of its preliminary evaluations. Test System As shown in Figure 1, the system is basically composed of three vibration generators, a multi-axis vibration control system, instrumented handle, handle fixture, and shaker-fixture linkages (stingers). [ ] Figure 2 shows the array of three vibration generators (MB Dynamics, Energizer BLACK-500 lbs) and their associated support bases and foundation developed by MB Dynamics (Cleveland, USA), which create the 3-axis simultaneous motion. These electrodynamic exciters are powered by power amplifiers which provide current proportional to the analog drive signal from a controller. The controller (JAGUAR Multi-Input/Multi-Output closed-loop vibration controller) was provided by Spectral Dynamics, San Jose, California, USA). NIOSH-designed instrumented handle was equipped on the system.

Jan 6, 2006

By Stewart A. Silling, Dale S. Preece

The two key results of rock blasting are fragmentation and movement of geomaterials. Movement/flow of the blasted rock is often referred to as heave. Modeling the movement of full scale blasting is now possible with 3D distinct element models and parallel processing.

Jan 1, 2016

Effects of Hydrated Mg2+ on KCl Flotation

Sep 13, 2010

By V. I. Kefeli

Public-private partnership efforts are working to create green landscapes from abandoned industrial sites. Fabricated soils, potentially an essential element of such landscapes, are designed to substitute for topsoil on the areas free from ground cover and plant community. The aluminosilicate matrix and humus form the soil micelle - the primary unit of any soil complex. Humus formation is a process based on carbon-nitrogen interaction. Sources of carbon can be materials rich in easily composted products like cellulose and polyphenols (plant leaves) or aged lignin polymers (saw dust from different woody plants). The pathways of carbon-nitrogen complexes are discussed. Properties of the fabricated soil components were examined by bio-tests and plant models.

Jan 1, 2002

The relationship between the maceral composition of coal and the strength of the coke produced from that coal has received a great deal of attention in recent years.Studies using two Bulli Seam coals, and blends of Bulli and Wongawilli Seam coals, from the IIIawarra Measures of the Southern Coalfield of New South Wales were carried out.The optimum range of vitrinite was found to lie between 45 per cent and 60 per cent (mineral matter free).Above and below this vitrinite range coke strength deteriorated. Coke strength indices increased with rank, and the optimum vitrinite content increased with an increase in rank. These changes require confirmation as trends by testing a third level of rank. It was noted that vitrinite content decreased with an increase in the specific gravity of separation of the coal.Use of petrographic analyses will increase confidence in choosing coals for coking, provided the coals are well known. Such analyses offer the possibility of greater flexibility in coal purchases and the possibility of producing a marketable blend from coals, which have limited market potential. Critical base coals for blends can be conserved.Significantly more work is required before coal reserves can be utilized to optimum advantage. This work would require extension of the studies discussed in this paper and, in particular, the testing of a wider range of rank.

Jan 1, 1971

By Sneddon N

In November, 1975, Aberdare North colliery was sealed at the surface to extinguish an open fire underground.The fire had developed from a spontaneous heating in one of the open goaf areas of the mine.The mine was re-entered with normal ventilation methods following the isolation of the working district containing the fire. The isolation was accomplished by remotely sealing the open roadways with lly ash emplaced through boreholes from the surface. A subsequent re-entry operation similarly closed the roadways close to the fire and enabled the re-opening of the sealed district.Most of the mine and the underground equipment was recovered after clearing of numerous falls and production recommenced on 25th October, 1976.

Jan 1, 1978

By R. H. Oitto

To determine whether reflectors could substitute for the trip lights referred to in the Federal Mine Safety Code, the Bureau of Mines studied trip safety devices under simulated haulageway conditions. The noticeability of reflectors compared with trip lights and fluorescent panels was evaluated from distances of up to 850 feet with light source intensities of up to 1-6 foot-candles (ft c). Reflectors tested consisted of a reflective lens in a holder secured to a frame that can be attached to a trip. Reflectors were found to be suitable for use as a trip safety device. In fact, for the conditions in many underground haulageways some reflectors would be more effective than a permissible trip light.

Jan 1, 1968

By E. O. RHODES

Germany's' wartime coal-tar industry had two main branches, which can best be considered individually because their raw materials, operations, and distributions were almost completely separated. One branch, old and well-established, was concerned almost entirely with processing coal tar produced by the high-temperature carbonization of caking bituminous coal. Carbonization was effected principally in byproduct- coke ovens and to less extent in vertical, horizontal, and inclined retorts. The high-temperature tar was all processed in tar-distilling plants that handled high-temperature tar almost exclusively.

Sep 1, 1947

By Jueun Lee, Jong-Hwa Yoon, K. Rider, Bernard J. Martin

Whole body vibration is known to affect movement accuracy [1], however little is known about changes in the organization of movement and movement strategies used to limit the influences of perturbations. The specific aim of this work is to analyze the motion and coordination of upper body segments of seated operators performing reaching tasks under whole-body sinusoidal vibration exposure and simulated vehicle ride motion. The long-term objective is to model reach coordination and predict the dynamic behavior of the upper body motion under vehicle vibration exposure. Method The reach task consisted of pointing with the right hand index finger to targets located on touch screens placed in front of the subject, 45° overhead and 90° to the right in the mockup cabin of an HMMWV placed on a 6 DOF ride motion simulator. The task was performed under stable (no vibration) and vibration (sinusoidal vibration or simulated ride motion) conditions. A motion capture system was used to record kinematic data of reflective markers to recreate body link trajectories. Joint angles (torso, shoulder and elbow; Figure 1) were then computed using quaternions. Coordination between body links was defined as a) the joints angle-versus-angle relationships between the upper arm and lower arm, and b) the joint motion onset relationships between torso, upper arm and lower arm in the time domain. Results Angle–versus-angle relationships. The relationship between upper arm vs. lower arm angle and torso vs. upper arm angle for a far forward reaching movement in the stable (solid lines) and vibration conditions (dotted lines) are illustrated in Figure 2. Fig 2A compares the control condition with a 4 Hz lateral vibration while Fig 2B compares the control condition with a 6 Hz vertical vibration. It appears that under vibration exposure the reduced upper arm extension is compensated by an increase in torso flexion. This effect is seen in the last phase of the movements (encircled areas). In addition, the lower arm extension is delayed under 6 Hz vertical vibration (Fig 2B left panel). Time of joint motion onset. The timing relationship between torso, upper arm and lower arm is largely a function of the target to be reached. Examples of delays between body links are illustrated in Figure 3. The control condition is compared to a 6 Hz vertical vibration for three

Jan 6, 2006